Start

The router supports

WPS.

Connection via wireless

router

In ready mode, press WPS button on the printer for 3 seconds.Then WPS LED will flicker slowly and printer will seek AP for 2mins.

Press WPS button on the router.WPS LED on the printer will flicker faster.

If the connection is successful,WPS LED will remain on.And Network configuration report will be printed.

Insert install CD in PC and click on Install now.

PC will seek printer to connect AP.

Check IP address after connected.

Click on Next to continue to install the

driver.

General Tips1. When connecting with initial setting router, sometimes wireless network is enabled only to the printer device. So, other devices could not be in wireless network. It's required to set security level such as WPA2-PSK/AES in router setting, or required to setup as if the printer does not support WPS.

2. When WPS connection is not working properly by the router error, turning off/on the router could solve the problem.3 . Able to check wireless connection between printer and router by ping test on PC. (Use the IP address from network configuration report)4. If more than 2 APs are found when printer is seeking AP, the connection could be failed. 5. If wired network is connected to the printer, it's required to remover the LAN cable.6. Printer supports security configurations such OPEN, WEP, WPA-Personal (WPA-PSK), WPA-Personal (WPA-PSK) modes. Other configuration could not be able to connect.

Connect PC and Printer with USB cable and insert install CD.

Then select "Wireless Setting and installation menu" and click Next

Select "Configure the wireless setting

manually"

The priner will seek the routers around. Choose the wirelss router that the user uses.

※ Router can be not shown in the list in case customer set the network hidden option.

Input wireless router network key,

if it is set.

Check the router information to be connected to the

printer.

When connection is done successfully you will see below

screen

Check printer IP and continue to

install driver.

Trouble shootings 1. If the user turn on/off the wireless router often, the Printer IP can be changed every time and could fail to connect. So, it is recommended to set static IP address . The static IP should be in same range with PC IP address , but not the IP address in DHCP allocation range of the router . Ex. PC IP : 192.168.0.100, DHCP IP address range : from 192.168.0.100 to 192.168.0.199 / The printer IP should be like 192.168.0.99

2. Error messases 1) Connection failure - General Connection Error 2) Connection failure - Not found SSID ▶ USB connection error : Pull out USB cable and connect back. Can not find wireless router : Need to check router setting or start printer setting ▶

again. Then select "Try again and reconnect"

3) Connection failure - PC connection Error ▶ Communication failure between PC and Printer : Requried to check PC IP setting status. Go to cmd > ipconfig and check if the allocated IP to PC is correct. If the IP is like 169.254.x.x, it's required to renew IP or set IP configuration again. Execute cmd > ipconfig/release, and execute ipconfig/renew to get new IP address.

Go to next sheet

NO

Yes Yes

No

Start

Does the Printer have

local UI?

Connection with mobile

device

Go to next sheet

NO

Yes

No

Does the Printer have

local UI?

Enable Wi-Fi direct function of printer referring to the menu map below

Yes

Install printer driver on PC via USB

Execute Samsung Easy Printer

Manager

Turn on the Wi-fi direct on mobile device. Search the printer and press connect on mobile menu.

Does the mobile device

support Wi Fi direct?

Go to wifi network configuration on mobile device

Yes

No

Execute Samsung Easy Printer

ManagerGo to advanced mode Go to Network under

device setting

Turn on the Wi-fi direct on mobile device. Search the printer and press connect on mobile menu.

Press WPS button on printer when the LED starts to flicker.

Go to wifi network configuration on mobile device

Search network and connect to DIRECT-XXML-2160 (printer model name)

Input network key

※ Wifi direct can connect max. 4devices

Go to Network under device setting

Set Wi-Fi direct value to On and

check current network key and

click save.

Input network key

※ Wifi direct can connect max. 4devices

Execute mobile print application on mobile device.※Download from Samsung Apps, Google market or Apple App store

If user doesnt know the network key, user can verify in easy printer manager

Set Wi-Fi direct value to On and

check current network key and

click save.

Start

Does the Printer have

local UI?Connection

with PC

Go to next sheet

NO

Yes

No

Does the Printer have

local UI?

Enable Wi-Fi direct function of printer referring to the menu map below

Yes

Install printer driver on PC via USB

Execute Samsung Easy Printer

Manager

Go to wifi network configuration on PC

Execute Samsung Easy Printer

ManagerGo to advanced mode Go to Network under

device setting

Search network and connect to DIRECT-XXML-2160 (printer model name)

Input Network Key

Trouble shootingsIf the printer is not shown in network list,1. Check Wi-Fi direct is on .2. Check if there are more than 4devices connected to the printer. (Max 4devices can be supported via Wi-Fi direct) 3. Reboot PC wireless module (disable -> Enable)

Go to Network under device setting

Set Wi-Fi direct value to On and

check current network key and

IP address.

Input Network Key

If user doesnt know the network key, user can verify in easy printer manager

Change printer port in Devices and printers

Trouble shootingsIf the printer is not shown in network list,1. Check Wi-Fi direct is on .2. Check if there are more than 4devices connected to the printer. (Max 4devices can be supported via Wi-Fi direct) 3. Reboot PC wireless module (disable -> Enable)

Set Wi-Fi direct value to On and

check current network key and

IP address.

Change printer port in Devices and printers

Left click on the printer to use and go to printer properties

Click Add port and select Standard TCP/IP port, and click New port

Click Add port and select Standard TCP/IP port, and click New port

Click Next and input IP address Complete setting

User can see printer IP address in easy printer manager

Complete setting

Trouble shootingsIf printing via wifi is not able after setting up, check the setting is correct from Network configuration report.

Wi-Fi Direct InformationWi-Fi Direct : Enabled Device Name : ML-2160 (Model name) IP Address : 192.168.3.1 Role : Group Owner Current SSID : Direct-xxML2160 (Model name) Network Key : 12345678 Current Status : Connected (1) ← This is the number of device connected to the printer.

Trouble shootingsIf printing via wifi is not able after setting up, check the setting is correct from Network configuration report.

Wi-Fi Direct InformationWi-Fi Direct : Enabled Device Name : ML-2160 (Model name) IP Address : 192.168.3.1 Role : Group Owner Current SSID : Direct-xxML2160 (Model name) Network Key : 12345678 Current Status : Connected (1) ← This is the number of device connected to the printer.

Ad-hoc connection

Connect PC and printer via USB and insert install CD.

※ PC wi-fi should not be connected to any network.

Select Wireless Setting and Installation menu

If user sees the screen as below, connect PC network to portthru

When connected, user will see below screen.

Select Wireless Setting and Installation menu

Select Configure the wireless settings manually

Remove USB connection Move to driver installation stage

Select Configure the wireless settings manually

Select portthru at the bottom of network list

Check if the protocol property is set as Obtain IP address automatically. If wired network is connected, it is required to remove LAN cable.

Move to driver installation stage

After installation is completed, go to Devices and Printers to check if the printer is installed correctly

Left mouse click and go to printer properties

Select portthru at the bottom of network list

Check the network name and operation mode. And click next

Left mouse click and go to printer properties

Go to "Ports" tab and click "Configure port.."

Check the network name and operation mode. And click next

Go to "Ports" tab and click "Configure port.."

If printer name is shown correctly, the printer is set up well.

If printer name is shown correctly, the printer is set up well.

Trouble shooting guide

1. Check the connection status between printer and AP. - Check WPS LED. LED would be off when printer is off or in power saving mode. (Press power button) - WPS LED status . Off : not connected / Flickering : Connecting / On : Connected

2. Check followings - Whether the printer is conneced to other mobile devices. - Whether the distance between printer and router or the devices is far. - The printer and router or devices should be located within 50m without wall or other obstructions. . Also metal case near printer can stop the signal

3. Check the IP information set in Printer - Print out Network configuration report and check followings . If the IP address of printer is same as the IP address that the router allocated. : If not same, reboot wireless router. - If there is PC connected to wireless router, perform ping test (cmd > ping -t <ip address>)

4. Check printer driver(port) on PC. - In case of using DHCP, IP can be changed sometimes when turning off/on the router or printer for long time. - Re-install printer port to host name. - Change the printer IP to static and change printer port on PC to the IP address. - Configure router option to allocate same IP address to the printer.

5. Initialize printer network setting - Restore the printer network setting to default value on Easy printer manager

6. Check printer wireless module. - Print out network configuration report and check if wireless network information is shown - If not recognized, it will be not shown or shown like Not installed.

- In case the information is not shown properly, check followings. . Upgrade to latest F/W . H/W connection status. (Wireless module or cables) . Report to HQ with information (Model name, FW ver, wireless setting information, symptom, wireless module HW version)

- Check WPS LED. LED would be off when printer is off or in power saving mode. (Press power button)

- The printer and router or devices should be located within 50m without wall or other obstructions.

. If the IP address of printer is same as the IP address that the router allocated. : If not same, reboot wireless router.

- In case of using DHCP, IP can be changed sometimes when turning off/on the router or printer for long time.

. Report to HQ with information (Model name, FW ver, wireless setting information, symptom, wireless module HW version)