WiFi-103 WiFi Lighting Control System · Repeat the a-b-c steps if you are connecting multiple WiFi-103 controller to same wireless router. d). Exit WiFi-103 application, go to mobile

This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).

Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.

This product is rated for indoor installation and only for dry locations.

Do not modify this product beyond the instructions in this guide or the warranty will be voided.Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding

Safety & Warnings

Before you begin, read all warnings and installation instructions.

1. Product Parameter:

WiFi-103 is a versatile RGB color control lighting system. Through WiFi function and mobile devices, the wi-103 can control various types of RGB LED lighting products VIA iOS or Android.

WiFi-103 lighting control system integrates four functional controls including; dimming, color temperature adjusting, and RGB controller. The WiFi-103 can work with the optional wireless T3 controller and T3-CV Receiving controller.

Communication Standard

Input Voltage

Max Current Load

Max Output Power

Product Size

Weight(G.W.)

2.4 GHz Wi-Fi, 802.11 b/g/n Protocol

DC12V~DC24V (Use only with Class 2 listed regulated power supply)

4A x 3CH Max 12A

144W/288W (12V/24V)

L128 × W73 × H45 mm

290g

WiFi-103 control system supports direct connection or by router:In directly connection, mobile phone, IOS and Android can directly control the WiFi-103 controller + T3-CV wireless control, without any third party of network equipment. Optional remote (T3) is available, if software is not used.

WiFi Control Distance

Working Temperature

Package Size

100m

-20°C ~ 40°C

WiFi-103 Controller

L135 x W80 x H50mm

WiFi-103 WiFi Lighting Control System

1LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA

Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

RGB Color Change Mode 32 xed modes, 8 DIY modes

Scene Mode 9 RGB modes, 3 CT (Color Temperature) modes

WiFi-103 Wi-Controller

2. Conguration Diagram

www.ledworldlighting.com

Working Frequency

Input Voltage

Max Current Load

Max Output Power

Product Size

2.4GHz

DC5V~DC24V (Use only with Class 2 listed regulated power supply)

6A x 3CH Max 18A

90W/216W/432W (5V/12V/24V)

L 178 x W 48 x H 33 mm

T3-CV Receiver

3. Controller Operating Instructions

ANTENNA installation instruction

1). Install / Uninstall ANTENNARotate Antenna clockwise to install. To uninstall rotate Antenna anti-clockwise

2). Light Indicator InstructionsŸ RUN : It ashes quickly about 25s during the electric

initialization. Flashes once per second after initialization

Ÿ LINK: It keeps on when the mobile device connected with WiFi controller, and turns off when disconnected

T3 Remote Controller

Wireless Frequency

Input Voltage

Battery Capacity

Remote Distance

2.4GHz

DC5V built-in Lithium Battery

≤30mA

1000mAh

30m

Current

Standby Time

Product Size

Weight(G.W.)

≤6 months

L 145 × W 55 × H 22 mm

200g



Power input/LED output

RUN

RX/TX

LINK

EXT KEY

SSID

MATCH

SCENE

SSID code switchIndicator Learning ID sceneManufacturerinterface

127.6mm

44.5mm

73m

m

RUN

RX/TX

LINK

EXT KEY

SSID

MATCH

FUN


4. ios/Android application instructions:

1). Download Application:


Channel Color

3). SSID Number SettingUse code switch to set the controller's SSID Number. WiFi-103-SSID-X, X is the code switch with numerical value (from 0 to F). Which means our product could set 16 isolated LAN in the same area. The controller will re-enter initialization status once the code switch changes. RUN LED indicator light will ash quickly about 25 seconds. Search with Mobile device and connect WiFi again after Initialization nished.

4). MATCH Key and SCENE KeyShort press SCENE to the user-dened scene modes sequentially, Scene mode will cycle through scenes 1 to 9, then cycle back from scenes 9 to 1.

Restore factory settings/Delete passwordLong press MATCH key and SCENE key simultaneously more than 2 seconds, the mach ine w i l l back to the defau l t parameter, including the parameters of changing modes and network parameters.

WiFi-103 controllers will be restored and connection password will be erased to blank..

scan to download android appscan to download ios app

2). How to operate the Application:A). Network connection setting :WiFi-103 support 2 connection modes: Directly connection as router or connect by additional router.

Ÿ Connecting WiFi-103 controller as a routerGo to mobile device's WiFi setting, Search the available WiFi Network. From the list select WiFi Network, appended with SSID-Number.(As Legend-1), (no password is set by default).

IOS WiFi connectionAndroid WiFi connection

(Legend-1)



Ÿ RX/TX: The indicator light turns on when the controller receives or transmits the WiFi data. Turns off in idle time

54 63 72 81 90 AF BE CD

RUN

RX/TX

LINK

EXT KEY

SSID

MATC

HSCENE

RGB scene interface CT scene interface

MATCH

SCENE

RUN

RX/TX

LINK

EXT KEY

SSID

MATCH

SCENE

Scene1 Scene2 Scene3



G 255255 255B 50R

PlayPlay

DIYScene Mode Device

Long press scene icons to Exchange pictures

WWW 10050


50

Save

12:34 PM 100% 12:34 PM 100%

WLAN settings

WLAN

Connect to WiFi-103-SSID-0

Network notification

Auto Connect

WiFi-103-SSID-0

TP-008

ACW1F

Notify me when an open network is

available

set the way of network’s connection

Connected

Remembered, secured with WPA/

WPA2 PSK

Remembered

WLAN networks

16:0714:17 PM

Wi-FiSettings

Wi-Fi

Other...

Ask t o jin Networks

Known networks will be joined automatically.if no known networks are available, you willhave to manually select a network.

CHOOSE A NETWORK...

WiFi-103-SSID-0

WiFi-103-SSID-1

100%


Ÿ Connect WiFi-103 with a additional router:

a). Connect to the WiFi-103 controller, as same procedure as (A)b). Click WiFi-103 application icon to start the app. The app will search and list the working WiFi controller automatically


c). Click Network key to enter Network interface(as legend-3-1). Turn ON connect to existing LAN option and app will search the available WiFi SSID list. Choose the available router to connect (Note : Do not choose WiFi-103 controller)(as legend-3-2 )

Repeat the a-b-c steps if you are connecting multiple WiFi-103 controller to same wireless router.

d). Exit WiFi-103 application, go to mobile wireless network setting, choose the wireless router to connect. Start WiFi-103 application again, device will list interface as legend-2-2. Complete the same steps to connect to the additional router.

(Legend 3-1)

Network interface

(Legend 3-2)

Note: In this connection mode, to avoid the mobile device automatically connect to WiFi-103 after the setting has completed, please click “workable WiFi-103". On dialog box click "Forget this network" or "Cancel save".

Cancel saved WiFi-103 connection information



Version:WiFi-103.0.15

Network

WiFi-103- 02SSID-

32:AA:3C:7E:B4:DA

Disconnected

Device List

WiFi-103-SSID-01

32:AA:3C:7E:B4:DA

Network

Driver

Connect to WiFi WiFi-103...

Driver

RGB

DIM

Version:WiFi-103.0.15

Network

WiFi-103- 02SSID-

32:AA:3C:7E:B4:DA

Connect to TP-LINK1

Device List

WiFi-103-SSID-01

32:AA:3C:7E:B4:DA

Network

Driver

Connect to TP-LINK1

Driver

RGB

DIM

Delete WiFi-103 controller from list

RGB Driver mode

Disconnected WiFi-103 controller

Network interface

RGB/CT/DIM Driver settingChange the background interface

Connected additional router

Available WiFi-103

14:17 PM 100%14:17 PM 100%

Connect with additional routerWiFi-103 connected as a router

Connected to WiFi-103

Manual searching button for WiFi-103 controller

NetworkBack

User setting

Wireless mode

Connect to existing LAN

Change SSID and password

NetworkBack

Available wireless LAN networks

TP-LINK1

WiFi-103-SSID-0

WiFi103SSID1- - -

User setting

Wireless mode



WiFi-103-SSID-2

WiFi-103-SSID-3

WiFi-103-SSID-4

12:34 PM 100% 12:34 PM 100%

WLAN settings

WLAN


Network notification

Auto Connect

WiFi-103-SSID-0

TP-008

ACW1F

Notify me when an open network is

available

set the way of network’s connection

Connected

Remembered, secured with WPA/

WPA2 PSK

Remembered

WLAN networks

16:07

WiFi-103-SSID-0

Cancel Forget Disconnect

StatusConnected

Signal strengthExcellent

Link speed65Mbps

SecurityOpen

IP address10.10.100.103

14:17 PM

WiFi-103-SSID-0Wi-Fi

Forget t his Netnwork

IP ADDRESS

100%

DHCP BootP Static

IP Address

Subnet Mask

Router

DNS

Search Domains

10.10.100.103

255.255.255.0

10.10.100.254

10.10.100.254

Hi_flying

www.ledworldlighting.com WiFi-103 Wi-Controller

B). RGB, CT, DIM Driver color wheel interface

C). RGB Linear Toning Interface

Click To modify linear toning interface in the RGB mode color wheel

Click on SCENE Button on the RGB driver interface. 9 scenes available in interface to choose from. The corresponding scene changing mode will display immediately, the mode parameters are displayed above the screen. Click Play key to cycle through dynamic change mode.

Click SAVE Button on the interface of RGB color wheel, linear toning, and mode. Select any Scene from 1 to 9, and click OK, the Scene name dialogue box will displayed. Scene name can be modied from dialogue box. Click OK to save current changing mode or CANCEL to Cancel the Save operation.



On application front screen, Device List interface is the default one. Click Driver into the Driver selection screen. Select the RGB/CT/DIM drive and return to the Device List interface. Click the color palette into the color palette interface, touch the color wheel to change and control the color, CT, brightness, saturation (RGB mode only) which connected to the controller, drag the brightness bar to adjust the brightness of the lighting. Click the ON / OFF button to turn off or turn on the controller. Click the save button to save scene operation.

50

GR 255 B255 255

Save


12:34 PM 100%

W 255

50

RGB mode

ON/OFF

RGB Values

Brightness Slider

Selected Color

Color Wheel

Driver interface

changing mode

Linear toning Interface

Scene saving

DIY interface

Select Driver

CT

RGB

DIM

Driver interface

Driver Interface

DriverWWW 10050


50

Save

12:34 PM 100% 12:34 PM 100% 12:34 PM 100%

Scene interfaceDimming modeCT mode

50

GR 197 B161 132

Save


78% 64% 52%

50

GR 197 B161 132

Save


78% 64% 52%

1 2 31 2 3

7 8 9

4 5 64

7

5

8

6

9

00Done

A B CA B C D E FD E F

GH IGH I J K LJ K L MNOMNO

P QRP QRSS T U VT U V WX YWX YZZ

12:34 PM 100% 12:34 PM 100%

RGB Slider

Scene Save

Brightness Slider

RGB value adjuster

RGB linear toning interface RGB value adjuster

D). RGB Scene Interface




G 255255 255B 50R

PlayPlay


Long press scene icons to Exchange pictures

12:34 PM 100%RGB Parameter Values

Long press changes the background scene

Scene modes

Dynamic scene play Button

RGB scene interface

E). RGB Scene Saving Interface


F). RGB Mode Interface



DeviceDIYScene Mode

Save

M1.Static red

M2.Static green

M3.Static blue

M4.Static yellow

M5.Static purple

ModeMode

Speed 8

Brightness 100%

12:34 PM 100%

DeviceDIYScene Mode

Save

M1.Static red

M2.Static green

M3.Static blue

M4.Static yellow

M5.Static purple

ModeMode

Speed 8

Brightness 100%

12:34 PM 100%

Saved to the Scene




OKOKCancelCancel

Modify the Scene nameScene saving interface

可修改场景名称CANCELCANCEL OKOK

Scene1

Please enter the scene name Please enter the scene name

Saved to the Scene




OKOKCancelCancel

Changing the Scene name

DeviceDIYScene Mode

Save

M1.Static red

M2.Static green

M3.Static blue

M4.Static yellow

M5.Static purple

ModeMode

Speed 8

Brightness 100%

12:34 PM 100%

Mode interface

Changing mode selection

Speed Slider

Brightness Slider

Play/Pause

Scene Saving

Static Red

Static Green

Static Blue

Static Yellow

RGB Skipping

7 Color Skipping

7 Colors Strobe

Red Fade out and Fade in

Static Purple

Static Cyan

Static White

Green Fade out and Fade in

White Strobe

Blue Fade out and Fade in

Mode Description

Adjustable Brightness







Adjustable Brightness/Speed







Yellow Fade out and Fade in

Mode Description















Purple Fade out and Fade in

Cyan Fade out and Fade in

White Fade out and Fade in

RGB Fade out and Fade in

Red Green color smooth

Red Blue color smooth

Green Blue color smooth

Red Yellow color smooth

Green Cyan color smooth

Blue Purple color smooth

Green Yellow color smooth

Blue Cyan color smooth

Red Purple color smooth

Color Changing Modes:

Blue White color smooth

Yellow/Purple/Cyan smooth





RGB color smooth

Full color gradual alternatively


G). DIY Interface

The Sequence for 10 color boxes is shown above. If the type of changing mode is jump, carry out the black, red, black, green, black, blue, black, yellow jump changing mode. That is red, green, blue, yellow strobe changing mode. If the changing mode is gradual, carry out the black,red, black, green, black, blue, black, yellow gradual changing mode. That is red fade out and fade in, green fade out and fade in, blue fade out and fade in, yellow fade out and fade in.

5. WiFi Network SSID Name and Password Setting

In Device list interface, click NETWORK KEY to enter Network interface. Select Change SSID and Password to enter User Setting interface. New SSID name and password must min 8 characters and consist of 0-9, a-z and A-Z. Click APPLY button on the top right corner of the interface to save the changes.



50

GR 255 B255 255


S6

S7

S5

75%

87%

62%

Jump

Gradual

D3

D4

D2SPEEDBRTMODEDIY

Delete the color

by long pressing

Save

12:34 PM 100%

DIY interface

Jump/Gradual/Strobe switching

Mode D1-D8

Long press to delete current color

Brightness adjustment

Color select box

Play/Pause

Scene saving

Speed selection

Brightness selection

Color wheel

For example:

H). CT Interface

1). Select Scene:Select any scene from 1 to 3 on the CT interface,The corresponding scene changing mode will be displayed immediately. Mode parameters are as shown on screen above.

2). Save Scene:On CT (Color Temprature) interface, from the color wheel select color temperature. Click SAVE to select any scene from 1 to 3, the Scene name prompt box will displayed. Click OK to save current changing mode as Scene changing mode or click CANCEL to Cancel the Save operation.

Parameter Values

Scene

Save Scene

CT mode Scene name

Modify the Scene Name

Settings

WWW 10050


50

Save

12:34 PM 100%

WWW 10050


50

Save

12:34 PM 100%

可修改场景名称CANCELCANCEL OKOK

Scene1

Please enter the scene name Please enter the scene name

8


LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA


NetworkBack

User setting

Wireless mode



14:17 PM 100%

User Setting

SSID

Password

WiFi-103-SSID-0

Ent the new Password

Back

Restore factory settings

Change the SSID name and password Apply

14:17 PM 100%

User Setting

Accoun

Change the account name and password

SSID

Password

Ltech-WiFi-103-0

Ent the new Password

Admin

Password

Restore factory settings

Change the SSID name and password

Cancel OK

Change the SSID password

Ent the NEW Password

Ent the NEW Password again

Back

14:17 PM 100%

Device List

2 3 4

5 6 7

1

8

10 11 129

WiFi-103-SSID-0

32:AA:3C:7E:B4:DA

Network

Zone


14:17 PM 100%

1.Device List interface 2.Network interface 3.Change SSID name interface 4.Change SSID password interface

Note: In direct connection of the WiFi-103 as a router, please close application after changing the SSID name and the password, then enter the mobile device system setting to reconnect the WiFi-103. In additional wireless router connection, it only needs to search again the WiFi-103 controller.

Note: To reset WiFi network password, simultaneously press : and more than 2s.It will delete the WiFi network password. More details in page 3 [Restore factory settings/Delete password].

MATCH SCENE

6. Remote Control Operating Instructions

1). Learning method of T3 to WiFi-103Learning ID:Short press learning key MATCH on WiFi-103 (buzzer sound), then short press any key on Remote within 5 seconds until the green LED indicator or the white one ashes 3 times (Long buzzer sound) means the controlling between remote and WiFi-103 is activated.

Cancelling ID:long press “MATCH” on WiFi-103 over 5 seconds (until long buzzer sound) means the conection between remote and WiFi-103 is cancelled.

2). T3 Remote Control Function Overview

T3

Color Circle

On/Off

Speed Control Buttons

Mode Control Buttons

Pause Key

Sync Indicator Light

Brightness Control Buttons

Saved Scenes




7. Conjunction Diagram

1). Wireless branch control connection:Can add branch control with T3-CV

The method of synchronization for the WiFi-103 controller and T3-CV:Learning ID: Long press the SCENE key on the WiFi-103 controller more than 2 second until the long buzzer sound. Then short press the ID on the T3-CV until the long buzzer sound. During the synchronization RUN light will ash quickly.

Cancelling ID: Long press the SCENE Key on the WiFi-103 controller untill long buzzer sound twice. It will cancel the synchronization between the WIFi-103 and T3-CV.

50 G

R255

B

255

255

Save

DIY

Scene

Mode

Settings

12:34 PM

100%

50

GR 197

B161

132

Save

DIY

SceneMode

Settings

78%

64%52%

12:34 PM100%

T3-CV

T3-CV

T3-CVT3-CV

T3-CV

Router

50

GR 255 B255 255

Save


12:34 PM 100%

Mobile phone

WiFi-103

T3-CV

T3-CV

WiFi-103

T3-CV

T3-CV




2). Remote Distance Reference

Router

50

GR 255 B255 255

Save


12:34 PM 100%

Mobile phone

WiFi-103

T3-CV

T3-CV

WiFi-103

T3-CV

T3-CV

3). LED Strip Connection

Warning: Input voltage must be identical to output voltage of the LED Fixture!

Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 22 to 16 AWG gauge wire for output terminals.

WIRE 6-8 MM (0.25-0.30")

RGB mode

CT mode

121

121

121

121

121

121

121

121

RGB three-in-one LED strip

+

B

R

G

+

B

R

G

121

121

121

Two- in -One color temperature led strip

121

121

121

ww

w

511

511

331

511

511

331 331

121

121

511

511

331

511

511

331 331

+

B

R

G

+

B

R

GWiFi-103

WiFi-103

DIM mode

121

121

121

+

single color LED strip

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

121

WiFi-103

Class 2 Low Regulated Power SupplyL

N

AC Power50/60Hz

G

N

L tu

pnI

tu

ptu

O

V+

V-


N

AC Power50/60Hz

G

N

L tu

pnI

tu

ptu

O

V+

V-


N

AC Power50/60Hz

G

N

L tu

pnI

tu

ptu

O

V+

V-




8. Limited Warranty

We provide lifelong technical assistance with this product

A 1-year Limited factory warranty from the date of purchase. The warranty is for free repair or replacement and covers manufacturing faults only.

Documents

WiFi-103 WiFi Lighting Control System · Repeat the a-b-c steps if you are connecting multiple WiFi-103 controller to same wireless router. d). Exit WiFi-103 application, go to mobile