S t o r a g e S o l v e d®

M o b i l e

TECH DATAFACE PANELS FOR WHEELHOUSE SYSTEMS

STEEL FACE PANELSSteel face panels provide a clean, sturdy finishing treatment for the ends

of Spacesaver Wheelhouse™ High-Density Mobile Storage Systems.

DESIGN AND CAPABILITIESSpacesaver’s 18 gauge (1.2 mm thick) mobile system face panels provide a strong, steel finishing alternative that features a one-piece, 4 bend structural construction with no sharp exposed edges, and has the flexibility to work with all types of storage housings including those that are custom designed.

STRENGTH: Each steel panel is reinforced for strength and rigidity with a minimum of three horizontal hat channels welded to the inside of the top, base and center.

AESTHETICS: Steel face panels feature a clean, smooth exterior with no exposed assembly holes and no protruding hardware. They are secured to the mobile system with specially designed face panel supports to ensure and maintain accurate and true alignment. They are powder coat painted in any of the standard colors for a hard, durable finish that will complement the mobile system and the surrounding decor.

FLEXIBILITY: Steel face panels are designed to completely cover the full width and height of any storage housing and the carriage base providing a continuous, one-piece finish.

Standard Steel Face Panel

Wheelhouse Steel Spacer

Wheelhouse™

H I G H - D E N S I T Y M O B I L E S T O R A G E S Y S T E M

www.southwestsolutions.com

3.416”(87 mm)

2.250”(57 mm)

6.916”(176 mm)

3.5”(89 mm)

3.416”(87 mm)

2.250”(57 mm)

5.66”(144 mm)

2.25”(57 mm)

3.416”(87 mm)

2.250”(57 mm)

3.916”(99 mm)

.5”(13 mm)

Spacesaver Corporation1450 Janesville AvenueFort Atkinson, WI 53538-27981-800-492-3434www.spacesaver.com

KI1330 Bellevue Street

P.O. Box 8100Green Bay, WI 54302-8100

1-800-424-2432www.ki.com

STEEL FACE PANELS:All exposed ends (refer to drawings) shall have steel face panels covering the full width and height of the carriage and storage housing. Face panels shall be constructed of 18 gauge (1.2 mm thick) steel using a 4-bend (2-bend for manual systems) structural design that forms a 2 1/4” (57 mm) [3/4” (19 mm) for manual systems] thick edge channel that runs the full length of each vertical edge. A minimum of three 18 gauge (1.2 mm thick) structural hat channel supports shall be welded into the back of the

panel at the top, base and center to provide unit rigidity. Face panels shall be free of any exposed assembly holes or protruding hardware, and shall be assembled without any exposed sharp edges. Face panels shall be powder coat painted from manufacturer’s standard colors. For mobile applications with platforms, two 3” x 5” (76 mm x 127 mm) cardholders shall be provided per aisle entry location and attached to the end panels with centers located 60” (1524 mm) above the finished floor.

TECHNICAL SPECIFICATIONS

Specifications are subject to change.

FACE PANEL VERTICAL SPACER DETAILS AND DIMENSIONS:

POWERED WHEELHOUSE SYSTEMS MECHANICAL ASSIST WHEELHOUSE SYSTEMS MANUAL WHEELHOUSE SYSTEMS

Control Head

Spacesaver Corporation is a division of KI.

KI and Spacesaver are registered trademarks of Krueger International, Inc.

Spacesaver is a registered trademark of Spacesaver Corporation.

© 2010 KI and Spacesaver Corporation. All Rights Reserved. SC-10003 SSC/SSC 10/10

TECH DATA F a c e P a n e l s f o r W h e e l h o u s e S y s t e m s

www.southwestsolutions.com