1
Storage Solutions Fishing Enthusiast for the 2300 Bethards Drive, Suite S Santa Rosa, California 95405 888.654.8281 www.orgfishing.com Assembly Instructions WFR-012 Tackle Trolley 1. Lay out all parts and components on a flat surface. 2. With arrow pointing up and side by side, attach 2 plastic holders (2) to the end of the lower tube with locking wheel (4). Slide up or down until it clicks, making. sure that the ridge inside the plastic holder (2) fits in the indent around the tube (4) 3. Repeat step 2 on the other lower tube with locking wheel (4) and the 2 lower tubes with non-locking wheels (5). Make sure that all plastic holders (2) are at the same height on all four lower tubes. 4. With the shelf apron facing down, slide a shelf (6) down over the four lower tubes (4 & 5). By pressing down on the shelf make sure that the shelf (6) sits balanced and firmly on top of the plastic holders (2) 5. Screw the upper tubes (3) in to the top of the lower tubes (4 & 5). 6. By repeating step 2, attach 2 plastic holders (2) to each tube at the desired location for the second shelf. Slide up or down until it clicks, making sure that the ridge inside the plastic holder (2) fits in the indent around the tube (4) It is recommended that the second shelf is at least one foot above the bottom shelf. Make sure that all plastic holders (2) are at the same height on all four tubes. 7. With the shelf apron facing down, slide a shelf (6) down the lower tubes (3, 4 & 5). By pressing down on the shelf make sure that the shelf (6) sits balanced and firmly on top of the plastic holders (2). 8. Repeat steps 6 & 7 for the third shelf (6) 9. With the hooks on the back of the rod butt holder (8) slide the rod butt holder down on to the wire apron at the narrow side of the bottom shelf (6). Repeat for the other rod butt holder on the opposite side of the bottom shelf. 10. With the hooks on the back of the rod tip holder (1) slide the rod tip holder down on to the wire apron at the narrow side of the top shelf (6). Repeat for the other rod tip holder on the opposite side of the top shelf. Slide rubber clips along rod tip holder for desired spacing between rods. 11. Reducing or increasing the distance between the rod tip holders (1) and the rod butt holders (8) can be made by attaching either holder to a different shelf and/or by adjusting the height of the shelves. You can find appropriate distances between the rod tip and rod butt holders for all sizes of fishing rods. 12. Apply the peg hooks (7) to the front of the shelves. 13. Please make sure that the locking wheels (4) are unlocked when you want to move the unit. This product is not designed to hold a total weight of more than 150 pounds. Please distribute the weight on the shelves evenly for best results. TM

WFR-012 assembly instructions - Kotula's · 2013-04-18 · Storage Solutions Fishing Enthusiast for the 2300 Bethards Drive, Suite S Santa Rosa, California 95405 888.654.8281 ˜shing.com

  • Upload
    others

  • View
    0

  • Download
    0

Embed Size (px)

Citation preview

Page 1: WFR-012 assembly instructions - Kotula's · 2013-04-18 · Storage Solutions Fishing Enthusiast for the 2300 Bethards Drive, Suite S Santa Rosa, California 95405 888.654.8281 ˜shing.com

StorageSolutions

FishingEnthusiastforthe

2300 Bethards Drive, Suite S Santa Rosa, California 95405 888.654.8281 www.org�shing.com

Assembly InstructionsWFR-012 Tackle Trolley

1. Lay out all parts and components on a �at surface.2. With arrow pointing up and side by side, attach 2 plastic holders (2) to the end of the lower tube with locking wheel (4). Slide up or down until it clicks, making. sure that the ridge inside the plastic holder (2) �ts in the indent around the tube (4)3. Repeat step 2 on the other lower tube with locking wheel (4) and the 2 lower tubes with non-locking wheels (5). Make sure that all plastic holders (2) are at the same height on all four lower tubes.4. With the shelf apron facing down, slide a shelf (6) down over the four lower tubes (4 & 5). By pressing down on the shelf make sure that the shelf (6) sits balanced and �rmly on top of the plastic holders (2)5. Screw the upper tubes (3) in to the top of the lower tubes (4 & 5).6. By repeating step 2, attach 2 plastic holders (2) to each tube at the desired location for the second shelf. Slide up or down until it clicks, making sure that the ridge inside the plastic holder (2) �ts in the indent around the tube (4) It is recommended that the second shelf is at least one foot above the bottom shelf. Make sure that all plastic holders (2) are at the same height on all four tubes.7. With the shelf apron facing down, slide a shelf (6) down the lower tubes (3, 4 & 5). By pressing down on the shelf make sure that the shelf (6) sits balanced and �rmly on top of the plastic holders (2).8. Repeat steps 6 & 7 for the third shelf (6)9. With the hooks on the back of the rod butt holder (8) slide the rod butt holder down on to the wire apron at the narrow side of the bottom shelf (6). Repeat for the other rod butt holder on the opposite side of the bottom shelf.10. With the hooks on the back of the rod tip holder (1) slide the rod tip holder down on to the wire apron at the narrow side of the top shelf (6). Repeat for the other rod tip holder on the opposite side of the top shelf. Slide rubber clips along rod tip holder for desiredspacing between rods.11. Reducing or increasing the distance between the rod tip holders (1) and the rod butt holders (8) can be made by attaching either holder to a di�erent shelf and/or by adjusting the height of the shelves. You can �nd appropriate distances between the rod tip and rod butt holders for all sizes of �shing rods.12. Apply the peg hooks (7) to the front of the shelves.13. Please make sure that the locking wheels (4) are unlocked when you want to move the unit.

This product is not designed to hold a total weight of more than 150 pounds. Please distribute the weight on the shelves evenly for best results.

TM