storage.googleapis.com€¦ · Web viewProcedure: Power Meter Guided Practice Equipment Used: Simulation interface, PM, WSC3 in cabinet, PM power cord, , power sensor cable, and SPECTRA

Requested By: Rick Trembley Course: CMJIRA Ticket: 08_06_CM006806_Practice Lesson: PMProcedure: Power Meter Guided Practice Equipment Used: Simulation interface, PM, WSC3 in cabinet, PM power cord, ,

power sensor cable, and SPECTRA Radio.Source: SME and Scope Document Scope Documents: Power Meter Scope doc.docx

Step

Step Text Actions Indications/Effect

Trigger (to advance to next action) Remediation Trainee Prompt Warnings/Cautions/Notes

1 With the LINE switch set to the OFF position, set the meter indication to zero with the meter zero button.

1. None Power meter is displaying front panel. No indicator lit. No cables are connected to either the front or back panels.

Power meter front panel. LINE switch is set to OFF.

None None None

2. Select the meter zero button.

Meter indicator on left side of meter display, on zero. LINE switch set to off. Power sensor cable on the table top, disconnected.

Meter indicator moves to zero. Indicator moves all the way to the zero on the left of the meter display.

1. That is incorrect. Try again.

2. That is incorrect. Remember, the meter must indicate zero. Try again.

3. That is incorrect. You should have selected the meter zero button.

None None

2 Connect the power sensor cable to the front panel input connector.

1. Select and drag one end of the power sensor cable to connect to the input connector.

Power meter front panel with power sensor cable connected and the power cable on the table disconnected and a power outlet.

The power sensor cable connects to the power meter’s front panel input connector.


2. That is incorrect. Remember, the power meter

None None

/tt/file_convert/5fbe4a942da7ca7cb250e922/document.docx Page 1

Step



must receive input from the power sensor. Try again.

3. That is incorrect. You should have connected the power sensor cable to the input connector on the front panel.

3 Connect the power cable to the power outlet and power cord receptacle.

1. Select and drag the male end of the power cable toconnect it to the work bench's power outlet.

Power meter front panel , power cable connected to power outlet.

Male end of the power cable connects to work bench’s power outlet.


2. That is incorrect. Remember, you must connect the power cable to a primary power source. Try again.

3. That is incorrect. You should have connected the male end of the power cable to the workbench’s power outlet.

None None

2. Select the rotation arrow. The power meter rotates. Power meter rear panel. 1. That is incorrect. Try again.

2. That is incorrect.

None None


Step



Remember, you must access the rear panel of the power meter.

3. That is incorrect. You should have selected the rotation arrow to display the rear panel of the power meter.

3. Select and drag the female end of the power cable to connect it to the power meter's rear panel power cord receptacle.

Female end of the power cable connects to the power meter rear panel power cord receptacle.

Power meter rear panel power cable connected to the power meter.


2. That is incorrect. Remember, you must connect the power cable to the power meter. Try again.

3. That is incorrect. You should have connected the female end of the power cable to the power cord receptacle.

None None

4. Select the rotation arrow. The power meter rotates. Power meter is fully rotated to front panel.


2. That is

None None


Step



incorrect. Remember, you must have access to the front panel of the power meter. Try again.

3. That is incorrect. You should have selected the rotation arrow to rotate the power meter and fully display the front panel.

4 Set the LINE switch to the ON position to connect power to the power meter.

1. Select the LINE switch to place it in the ON position to apply power to the power meter.

Light within the LINE switch illuminates.

Front panel . The LINE switch is in the ON position and the lamp within the switch lens should be lit.


2. That is incorrect. Remember, you must power on the power meter. Try again.

3. That is incorrect. You should have selected the LINE switch to power on the power meter.

None None

5 Perform the RANGE switch scale selection procedure to

1. Select the left side of the RANGE switch to turn it CCW to unscrew and remove the outer knob from the knob switch

The outer knob turns the CCW and unscrews.

RANGE switch is unscrewed and pulled out.


2. That is

None None


Step



select the appropriate range for the test measurement. (1.50-2.00 W).

assembly. incorrect. Remember, you must remove the outer knob from the knob assembly. Try again

3. That is incorrect. You should have selected the left side of the RANGE switch to unscrew and remove the outer knob from the knob assembly.

2. Select each scale ring to remove it from the knob assembly.

The two scale rings are removed from the knob assembly.

Rings on the table top, with scales visible.


2. That is incorrect. Remember, you must remove the scales from the knob assembly. Try again.

3. That is incorrect. You should have selected each scale ring to remove them from the knob assembly.

None None

3. Select and drag the scale The scale ring not being Scale not being used is back on the 1. That is


Step



ring not being usedonto the knob assembly.

used goes back on to the knob assembly.

knob assembly knob assembly. incorrect. Try again.

2. That is incorrect. Remember, you must put the scale ring not being used back on the knob assembly. Try again.

3. That is incorrect. You should have selected and dragged the scale not being used onto the knob assembly.

4. Select and drag the scale ring being used ontothe knob assembly.

The scale ring being used goes back on to the knobassembly with the appropriate scale facing out.

The scale ring being used goes back on to the knob assembly with the appropriate scale facing out.


2. That is incorrect. Remember, you must put the scale ring being used back on the knob assembly. Try again.

3. That is incorrect. You should have selected and dragged the scale ring


Step



being used onto the knob assembly.

5. Select the right side of the ring to move it Clockwise (CW)

The tabs of the scale rings line up with the slot in the knob assembly.

Rings back on the knob assembly. 1. That is incorrect. Try again.

2. That is incorrect. Remember, you must line up the tabs of the scale rings with the slot on the knob assembly. Try again.

3. That is incorrect. You should have selected the right side of the ring to move it clockwise.

6. Select the right side of the RANGE switch to turn it CW to lightly tighten the knob switch assembly.

The RANGE switch turns CW and tightens switch assembly.

RANGE switch back in its in its original location on the power meter.

SPECTRA Radio on Table top. 1. That is incorrect. Try again.

2. That is incorrect. Remember, you must tighten the knob switch assembly. Try again.

3. That is incorrect. You should have selected the

None None


Step



right side of the RANGE switch to lightly tighten the knob switch assembly.

6 Connect the power meter to the RF source.

(In this case, the SPECTRA Radio)

1. Select the rotation arrow to turn the radio and view the back panel.

The SPECTRA radio rotates. Rear view of the radio is fully shown. 1. That is incorrect. Try again.

2. That is incorrect. Remember, you must have access to the rear panel of the SPECTRA radio. Try again.

3. That is incorrect. You should have selected the rotation arrow to fully rotate the SPECTRA radio.

None None

2. Select and drag the unconnected end of the power sensor cable to the radio antenna jack to connect the power meter to the radio.

The power meter connects to the radio antennajack, on the back of the radio, using the power sensor cable test adapter.

SPECTRA radio is connected to the power meter.


2. That is incorrect. Remember, you must connect the

None None


Step



power meter to the radio. Try again.

3. That is incorrect. You should have selected the unconnected end of the power sensor cable to the radio antenna jack to connect the power meter to the radio.

3. Select the rotation arrow. The radio rotates. SPECTRA radio, front view is fully shown.


2. That is incorrect. Remember, you must rotate the SPECTRA radio. Try again.

3. That is incorrect. You should have selected the rotation arrow to fully rotate the SPECTRA radio.

4. Select the transmit key to press and hold.

The transmit key presses and holds.

Radio transmit key is pressed. 1. That is incorrect. Try again.

2. That is


Step



incorrect. Remember, you must press and hold the transmit key. Try again.

3. That is incorrect. You should have selected the transmit key to press and hold.

5. Select the transmit key to release.

The transmit key releases. Radio transmit key is released. 1. That is incorrect. Try again.

2. That is incorrect. Remember, you must release the transmit key. Try again.

3. That is incorrect. You should have selected the transmit key to release.

6. Select and drag the end of the power sensor cable connected to the radio antenna jack to disconnect the power meter from the radio.

Power sensor cable connected to the radio jack disconnects.

Radio is disconnected from the power meter.


2. That is incorrect. Remember, you must disconnect the radio from the power meter.


Step



Try again.3. That is

incorrect. You should have selected an d dragged the end of the power sensor cable connected to the radio antenna jack to disconnect the power meter from the radio.

7 Read the power level in dBm or W on the meter.

1. Trainee will document the final rated output power reading.

Rated output power reading between 1.50-2.00 W on power meter display.

End of simulation. Show the following pop-up message:“You have successfully completed the Power Meter Practice.”

None
