Module 9: Topic 1Visibility

1. Driving at Night:a. Dirt on the lens of headlights can reduce light by up to _____ percent.b. How can you check to see if the lights are working properly?

c. How far do high beams let us see?

d. What is the sight distance rule?

e. When driving at night, drivers need to leave more ________than they would in the daytime.

2. Visibility:a. The distance a driver can see ahead is limited and headlights do not illuminate off-

road areas.b. Visibility is also compromised by the ___________ from other vehicles.

3. Headlights:a. High beam headlights

Used when safe and legal at speeds of ___________ mphb. Low beam headlights

Used in bad weather or when following or meeting another car at night - safe at speed of __________ mph

4. Night Driving Skills:a. Adjust speed to distance illuminated by headlightsb. Keep your eyes ____________ searching ahead and at edges of the roadwayc. Flash lights once quickly if oncoming vehicle is using high beams

5. Night Driving Risks:a. Reduces ability to see risksb. Requires eyes to adjust quickly to glarec. Places limitations on gathering and processing information in timed. The distance you can see ahead is shorter - especially at higher speedse. Headlights provide little illumination of off-road areasf. Ability to judge distances is compromisedg. The glare from oncoming and following vehicles impairs visionh. Must drive “blind” while recovering from the glare

6. Driving Tips for Poor Visibility:a. ________speed to accommodate shortened sight distanceb. Use _______________ flashers when traveling below speed limitc. Maintain appropriate lane position

d. If stopping distance longer than sight distance, slow down and don’t drive “blindly” into the darkness.

7. Safety Tips for Driving at Night:a. Before passing, the driver passing can flash his/her headlights to warn the other

driver.b. When two vehicles are ______ by _______, the passing driver may switch to high

beams and the driver being passed should switch to low beams.c. Be alert for pedestrians walking on unlit roadways. d. If you must walk on a dark roadway due to vehicle breakdown or another reason,

carry a white handkerchief or wear _______-colored clothing or reflective clothing to increase your chances of being seen.

e. In snow, wear ________ clothing to create a contrast.

Module 9: Topic 2Severe Weather Conditions

1. Drifting Fog:a. Reduce speedb. Turn on ______ beam headlights c. Turn on windshield wipersd. Turn on defroster or air conditioner

2. Heavy Fog:a. Reduce speedb. Turn on emergency flashers and fog lightsc. _________ stop in a travel laned. Look for an exit from the highwaye. If impossible to leave the highway, stop beyond the _____ of guardrail as far to the

right of the road as possible, and turn ______ lights and wait for fog to lift.

3. Visibility Limited by Rain and Snow:a. Keep headlights cleanb. Turn on the defroster to remove ice and condensation c. Clear the windshield and rear windowsd. Reduce Speede. Turn headlights to low beamf. Turn on windshield wipersg. Be alert for vehicles stopped in roadwayh. Be prepared for effects of gusting windsi. Make adjustments gently and smoothly

4. Sources of Glarea. Other vehicle headlightsb. Paper on the dashboardc. Snow covered landscape

d. The sun at dawn or dusk

5. Reducing Glarea. Look to the ______ edge of roadwayb. Do not place paper on dashboardc. Wear ____________ during the dayd. Adjust sun visors and mirrorse. Clean window

6. Describe how the conditions listed below affect a driver’s ability to see and what adjustment a driver should make to better cope with these conditions:

1. Sun glare:2. Driving at night:3. Fog:4. Rain:5. Snow:

7. Driving in Snow:a. In severe snow conditions look for an exit on highwayb. Check weather report c. If impossible to leave highway, stop beyond outboard end of guard rail d. Use cell phone to check conditionse. Snow may require use of windshield washer fluid

8. Strong Winds:a. Keep a _______ grip on the steering wheelb. __________ speedc. Adjust lane positiond. Do not over steere. Stay off the brakef. Prepare to counter steerg. Make all steering, accelerating, and braking actions gently and smoothlyh. Check for debris in roadway and oncoming traffic

9. Low water crossings:a. Flash flooding conditions are unpredictableb. Not specific to a time of yearc. Affects braking, steering and engine systems

10. Flash Flood Dangers:a. Nearly ______% of flash flood fatalities are vehicle related b. Search for flood prone areas:

Highway dips Bridges Low areas

c. Most vehicles will float d. Very little water on the road surface can cause loss of controle. ________ feet of water will “carry” most cars

f. Because visibility is limited at night, driving during flooding conditions is very dangerous

g. Heed all flash flood watches and warningsh. Monitor road conditions through the news media

11. Hot and Cold Temperatures:a. Vehicles are designed to operate in a wide range of temperatures, from very hot to

extremely cold.b. Extreme conditions cause stress on vehicle parts sensitive to temperature changec. Make sure to check tires, fluids, and belts

12. Cold Weather Driving Tips:a. Check your _______________b. Check your cooling systemc. Check your windshield wipers d. Check your tire treade. Check your gasf. Check your windshield washer reservoirg. Check radiator coolant, hoses, and connectionsh. Clean snow off of your entire car

13. Hot weather checks a. ______________ tires are subject to excessive flexion causing pressure buildup,

especially when driving for extended distances at higher speeds.b. The air conditioner, radiator coolant hoses, connections, and drive belts need special

attention due to the extra load placed on these cooling systems.

Module 9: Topic 3Occupant Protection

1. Occupant Protection:a. Occupant protection refers to safety features designed to protect occupants of motor

vehicles in the event of a crash. These systems can be 'active' or ‘passive.’b. Wearing a safety belt is your best defense for preventing severe life-altering injuries:

Slows occupant’s rate of deceleration in a frontal crash and keeps occupants securely in place

2. Airbags:a. The driver side airbag is located in the center of the steering wheel and the passenger

side airbag is located inside the dashboard. b. Side airbags that inflate during side collisions are usually located within the seat. c. Curtain airbags are installed above the side windows, in the headliner, on both sides. d. Knee airbags are located in front of the legs of the driver and front seat passenger.

They are concealed within the steering column or the lower part of the dashboard and deploy during frontal impacts.

e. Driver and front passenger air bags are designed to inflate in a frontal impact. Drivers should sit at least ______inches from the air bag because it inflates to six or

seven inches in size at speeds up to _______ mph. If you can, tilt the steering wheel to point the air bags at your _______, not your

face.f. Always wear a safety belt and secure children in the rear seat. g. To reduce forearm and hand injuries, place hands on the _______ half of the steering

wheel, with knuckles on the outside and thumbs along the inside of the rim of the wheel.

h. Side impact air bags are designed to protect the ______ and ______ in side impact collisions. Care should be taken not to sit too close to the door or to lean towards the air bag.

3. How do you adjust your seat and steering wheel hand position to protect you from the airbag?

4. We learned in Module 2 that adjusting the head restraints protects us from whiplash.

Module 9: Topic 4Highway Safety Design

1. Roadway Safety Design:

a. ____________ sign support posts

b. ________________ with ends angled away from roadway and buried

c. _______ attenuators - such as vinyl liquid or sand filled drums

d. Protected left and right turn bays

e. Collector/distributor lanes on high speed, high density highways

f. Variable message signs alerting drivers to weather conditions, construction, and traffic problems

Module 9: Topic 5

Vehicle Design and Technology

1. How do you think vehicle design and technology make a vehicle safer?

2. New Advances:a. All-wheel driveb. Antilock braking systems c. Electronic stability control d. Telematics (i.e. OnStar) e. Tire pressure monitoringf. Active head restraints g. Adaptive cruise control h. Adaptive headlights i. Advanced airbags j. Advanced seat belt pre tensionerk. Fatigue warning l. Forward collision warning systems m. Lane departure warning systems n. Side view assisto. Park assist and back over prevention

3. In Module 3 we learned about anti lock braking systems (ABS).a. What is the primary task of ABS?

b. What are the ABS rules?

c. What may you notice when using ABS brakes?

4. Electronic Stability System (ESP):a. What is the electronic stability program designed to do?

b. During an over-steering or skidding condition (rear-wheel lock-up), the ESP system applies the brake to which wheel?

c. During an under-steering or sliding condition (front-wheel lock-up), the ESP system applies the brake to which wheel?Answer:

5. Functions of Tires:a. Tires are air-filled cushions designed to reduce the effect of road hazards and

irregularities on the vehicle and are designed to flex and give as they meet the road surface.

b. Absorb shocks caused by road hazards c. Provide Traction — enables drivers to accelerate, brake and steerd. Tires ratings are indicated on the sidewall of the tire

6. Traction:a. Measured by the ability to stop a car in straight-ahead motion on a wet surface -

tires graded A have the best traction performance, B grading is an above average rating and C indicates the tire meets government standards.

b. Temperature —tire’s ability to withstand heat. Tires graded A are the most heat-resistant and less likely to suffer a blowout under the same conditions as tires with grades of B or C.

c. Tread wear rating — the higher the tread wear rating, the greater the mileage – a tire with a tread wear rating of 150 is expected to last 50 percent longer than one graded at 100.

7. After watching the tire safety video, list 3 things you learned about tires.

Module 9: Topic 6Dangerous Road Conditions

1. Dangerous Road Conditions:a. Ice, snow, or frost/sleetb. Wet--particularly the first 15 minutes of rain after a long dry period when oil and

rubber particles have collected on the road surface and mix with waterc. Heavy rain or standing water d. Mud near farm entrances, construction sites, and truck crossingse. Wet leavesf. Broken or uneven road surfaceg. Sand or gravel - frequently found on curves in rural areas

2. Slippery Conditions:a. Ice on the roadb. Dangerous curves and turnsc. Roads with slippery when wet warning signs d. Most dangerous when the temperature is near freezinge. Just after a rain has fallen on a hot dayf. Heavily traveled intersections when raining

3. Controlling Consequences:a. _______ off road rather than skid off the roadb. Hit something ______ rather than something hard c. Hit something going your way rather than something stationaryd. Hit stationary objects with a glancing blowe. Hit a stationary object rather than an approaching objectf. Steer to avoid oncoming traffic and head on collision

4. Preventing Loss of Traction:a. __________ speed b. ___________ spacec. Make gradual changes to speedd. Avoid abrupt changes in directione. Find the best path

5. Causes of Traction Lossa. Road surface conditionsb. The condition of the vehicle c. Actions of the driver

6. Signs of Hydroplaning:a. Standing waterb. Raindrops that bubble when they hit the roadc. Slushing soundd. Sensation that the steering wheel is loose or disconnected from the vehicle e. A vehicle ahead that is not leaving a track

7. Preventing Hydroplaning:a. _________down when there is water standing on the surface of the pavement.b. Tires should be properly __________ and have adequate tread.c. ___________ following distance, particularly when behind a large truck.d. Drive in the tracks left by any vehicle ahead.

8. If Hydroplaning Occurs:a. Ease off the ______________ graduallyb. ______________ speed until your tires regain traction.c. Do not ___________ until traction has been restored.d. Steer no more than necessary, continue to ______ and steer where you want to go.

9. What do you know about skids?a. When do most skids occur?

b. What are the steps to recover from a skid?

c. What is the best way to handle skids?

10. Causes of Skidsa. Slippery surfacesb. ____________ too hard c. ____________ too hardd. Steering too much or too quicklye. Entering a curve with too much speed

11. Preventing skids:

a. Apply the brakes in a __________ and progressive mannerb. Make smooth, precise steering wheel movementsc. Slowing down well in advance of curvesd. Maintaining speeds appropriate for conditions

12. Types of skids:a. There are two main types of skidding:

________-steering (fishtailing) ________-steering (plowing)

13. Front wheel loss of traction:a. Called “Under steer” and is when the vehicle moves straight ahead in spite of steering input

Look and steer toward intended path Smoothly ease up on accelerator Smoothly apply brakes to regain traction Do not steer more than necessary

14. When Brakes are Applied Too Hard or Too Quickly:a. Vehicle weight shifts to the front causing:

A noticeable drop of the hood A noticeable rise of the rear Forward movement of driver, passengers and items in vehicle

15. Correcting Front Traction Loss:a. Direct vision to targeted path of travel (look where you want to go)b. Activate ________ (if vehicle equipped)

Ease off conventional brake system Reestablish rolling traction (wheels rolling/not sliding)

c. Ease off steering inputs Abrupt steering can create traction loss Steer toward intended path of travel

d. Jab/Stab brake to move weight forward if no ABS (ABS performs this function automatically)

16. Rear-Wheel Loss of Traction:a. This is called an “over steer” when vehicle moves sideways without any additional

steering input• Look and __________ toward intended path • Ease off the accelerator and avoid using the brakes• Continue to steer and counter-steer until the vehicle is traveling straight• Use a light and progressive acceleration if the vehicle does not recover

17. Acceleration and Traction Loss:a. When acceleration is applied too hard or too quickly weight moves to the rear of the car causing:

• A noticeable rise of the hood • A noticeable drop of the rear • Rearward movement of driver and passengers

18. Causes of Traction Loss:a. Brakes __________ adjusted - Brakes pulling in one direction or the other can cause a

skid - as can wheels that are out of alignment when brakes are appliedb. Unevenly worn tire __________

The size of the front and rear tires do not match. The tread depth or the front and rear tire type are not the same.

19. Driver Actions that Cause Loss of Traction:a. Sudden steering movements on a slippery surfaceb. Abrupt and sudden changes in vehicle speedc. Panic stop or applying the brakes too hard on a hill, curve or slippery surfaced. Suddenly engaging the clutch on a slippery surface

20. Traction Loss – Shifts in Vehicle Weight:a. Sudden shifts of vehicle weight (left, right, forward or backward) will cause loss

of traction. b. Simultaneous steering, braking and/or acceleration creates sudden shifts in

vehicle balance.

21. When Steering is Applied Too Hard or Quickly Weight Moves to the Opposite Side of the Car:

a. Vehicle weight shift causes: • A noticeable ______ and tilt of the hood • A noticeable rise and tilt of the rear • Driver, passenger, items in car move towards the car’s corner

22. Managing Rear Traction Loss:a. Look at desired/targeted path of travelb. Activate traction control system orc. Ease off brake or acceleratord. Reestablish rolling traction to rear wheelse. Steer toward targeted path of travelf. Apply light progressive acceleration (2 mph is goal) to shift weight to the Rear g. Traction control system will adjust the speed/braking automatically when

activated)

Module 9: Topic 7Emergency Recovery & Controlling Consequences

1. What do you think causes run off the road crashes?

2. Run-Off the Road Crashes: Recognize, React, And Recovera. What are some reasons run-off the road crashes occur?

b. What increases the risk of being in a run-off the road crash?

c. What is the #1 tip from America’s best drivers when it comes to run-off the road crashes?

d. What steps should you take if you run-off the road? 3. Causes of Run Off the Road Crashes:

a. _________ or distractionsb. Drowsinessc. Steers onto the shoulder to avoid a collision and tries to return to the roadwayd. Vehicle may collide with a vehicle in the next lane, or drive off the far side of the road

4. Off road recoverya. To return to the pavement safely:

Keep a firm grip on the steering wheel Slow down, ease off the accelerator and allow the vehicle to slow ________ - avoid

braking ________ the edge of the pavement, after speed is reduced and there is a gap in

traffic . Steer back to the road with _______inputs, do not over steer Return to the pavement ________ wheels at a time, as soon as the front tire is back

on the roadway, counter-steer quickly left or right as necessary to stay in the correct lane

b. Blocked Roadside: If an object beside the road such as a tree, bridge abutment or pedestrian forces the driver to return to the road quickly, he/she has little time to slow down, to do this the driver should: Steer left or right so the off-road wheels are about 12 inches away from the edge of

the pavement Remove his/her foot from the accelerator and stay off the brakes. Turn the steering

wheel quickly about one-eighth turn toward the roadway Immediately, as the outer wheel makes contact with the edge of the pavement,

counter-steer about a quarter turn and make steering corrections to straighten vehicle

5. Reminders:a. Do not panic and steer abruptlyb. Ease off accelerator c. DO ______ BRAKEd. Get both wheels off the pavemente. Steer the vehicle parallel to the roadwayf. If clear, ease back on to the roadway one wheel at a timeg. _______ steering inputs to less than 1/8 of a turn of the wheel

h. Use even less input when edge of road is highi. Target the center of the adjacent lane to avoid a “Slingshot” maneuver into oncoming

traffic

6. Evasive Maneuvers:a. With ABS brakes, how can you stop quickly?

b. What is the safest maneuver if there is enough room?

c. What are the steps for making quick turns?

d. If there is a car beside you in the left lane and you need to avoid a car ahead, what should you do?

7. When do you use Evasive Steering?

a. When there is __________ to the sideb. When stopping distance is questionablec. When there are cars close behind

8. Procedures for Evasive Steering:a. Turn the wheel __________ degreesb. Counter-steer immediatelyc. Turn the wheel back to the original straight-ahead position

9. Evasive Braking:a. If the vehicle has ABS:

__________ press brake pedal until the vehicle stops May feel pedal pulse back against foot

b. If the vehicle does not have ABS:• Apply firm, steady pressure just short of lockup• Ease up on brakes if wheels lock, then apply the brakes again

10. Evasive Acceleration:a. Used less frequentlyb. Can be used to avoid crashes at intersections and in merging situationsc. May move point of impact to rear of vehicle if you can’t get out of the way

11. Controlling Consequencesa. Avoid __________collisionsb. Drive off the road rather than skid off the roadc. Hit something __________d. Hit something going in the __________ directione. Hit stationary object with glancing blowf. Hit stationary object rather than approaching object

Module 9: Topic 8Reporting Crashes

1. What are the four things that need to be done in the event of a crash?

a. What should you do to protect the scene? b. What should you do to take care of anyone who is injured?

c. What information should you get from the other driver if involved in a crash?

2. What should you do?a. __________ immediatelyb. Aid the injuredc. Prevent further damaged. Send for __________e. Exchange __________f. Record witnesses’ names and addressesg. Notify __________ agent

HOT

Module 10: Topic 1 Vehicle Warning Systems

Warning Symbol What does it mean? What should you do if you get a warning light?

__________________________________________

It warns you when the coolant in the engine is too hot or too

low.

If temperature warning light comes on or the gauge reads too hot, don’t drive the vehicle - seek

professional help.

Caution: Never attempt to remove the radiator cap when the engine is

hot - the pressure and hot steam may cause severe upper torso and

facial burns._________________________________ It warns you when the oil is

not circulating at proper pressure or there is not

enough oil.

When the oil warning light comes on it is recommended that you stop

at the nearest service center and have the oil level checked.

__________________________________________________________________

When the “ALT” light comes on or the gauge shows

“discharge” while the engine is running, the vehicle’s electrical

system is not functioning properly.

The engine must now use

The alternator is not generating enough electricity to charge the

battery.Turn off as many electrical devices

as possible. (i.e., the radio, heater/AC, etc.)

ALT

electricity stored in the battery.

Have this checked without delay. If the battery is drained, the car can

shut off.

_________________________________ This warning light serves two purposes:

(1) indicates the parking brake is set; and

(2) alerts you that part or all of the braking system is not working properly; or, (3) in some vehicles,

the brake fluid is low

If the parking brake is set, than take it off.

If it is not the parking brake, stop as soon as possible. Have the vehicle towed and the vehicle repaired.

_________________________________ The ABS light comes on when you start the vehicle indicating the

ABS system is functioning normally. If the light stays on, or comes on while you are driving,

there is a problem.

It should be checked by a qualified mechanic

_________________________________ When you start the engine, this light should illuminate

momentarily indicating the system is activated. If the air bag readiness light stays on or comes

on while you are driving, it is a warning that there is a problem.

If the air bag system in your vehicle is not working properly, it can be

dangerous as the air bags: May NOT inflate in a crash or May spontaneously inflate

while you are driving.

The SERVICE ENGINE or CHECK ENGINE light should flash for a

few seconds when you start

the engine and then go out.

If the light stays on, there may be a problem - make an appointment to

get it checked.

_________________________________This warning light will

illuminate when starting the engine and then goes out. If this light remains on, one or more of the vehicle doors is not completely latched. If it

comes on while driving, someone has opened a door or

the door latch was not properly fastened.

Pull off the road as soon as possible to secure the door.

_________________________________

The fuel gauge measures how much fuel is in the vehicle's

fuel tank. When the fuel level is low, the fuel warning light

will come on and stay on until you add more fuel to the tank.

Get more fuel immediately.

SERVICE

ENGINE SOON

Module 10: Topic 2Vehicle Malfunctions

DOOR OPEN

LOW FUEL

Type of Malfunction What happens to the vehicle?

What should the driver do?

_________________________________

_________________________________

This occurs when you hit a curb or

sharp object.

You have a defective tireOr

You have an under-inflated tire that

builds up heat and explodes or loses its seal to the rim while the tires are rotating.

If a front tire blows out, the vehicle will pull sharply in the

direction of the blowout.

If a rear tire blows out, the vehicle will

wobble and pull slightly in the

direction of the flat tire

1. Grip the wheel firmly2. Foot off accelerator3. DO NOT BRAKE4. Allow vehicle to slow5. Check traffic6. Turn on flashers7. Drive to a protected

area8. Change tire

_________________________________

_________________________________

The accelerator will not return to idle

when you release it and the engine is

racing.Accelerator failure is

caused by either a broken spring or the pedal getting stuck in

the down position.

In either case, you no longer have control over the vehicle’s

speed.

1. Shift to Neutral (engine may race but no harm done)

2. Search for an escape path

3. Steer smoothly and brake gently

4. Pull off the roadway and park

5. Turn off the vehicle. Caution — DO NOT turn the ignition off while the vehicle is moving--this may lock the steering wheel

6. Have the pedal repaired before driving again

_________________________________

_________________________________

When the engine stalls, the steering

mechanism will still work but will require

more effort.

1. Shift to neutral2. Look for escape path3. DO NOT BRAKE

HARD4. Pull off roadway5. Restart engine6. If unsuccessful, raise

hood and turn on emergency flashers.

_________________________________

________________________________

1. Turn off AC2. Turn on heater3. Pull off roadway if all

else fails

Module 10: Topic 3 Handling Special Vehicles & Pulling a Trailer

Two of the most important things to have when you tow are basic common sense and the ability to adjust your driving.

1. Handling Large Vehicles:a. Weigh more than a passenger vehicleb. Affect the ability to __________________, turn and slow down:

Allow enough space to get up to speed Slow down in advance of turns Allow more space between vehicles

c. Do not exceed load limitsd. Practice driving where there is no traffice. Allow a _________________in traffic before pulling outf. Check both side mirrors to be sure the trailer does not intrude into adjoining laneg. Roads that curve right

Allow more _________________ from edge of pavement Keep toward the center line

h. Roads that curve left Stay to the right so you do not cross the center line

Vehicle Normal Following Distance

Additional Following Distance

Total Following Distance

Automobile with no trailer

_________________ None needed 3 to 4 seconds

Automobile with 20-foot trailer

_________________ 2 seconds 5 to 6 seconds

35-foot motor home _________________ 2 seconds 5 to 6 seconds

2. Backing a Trailer by Turning Steering Wheel in Direction Driver Wants to Turn:a. Back slowly and look directly over your shoulder through the rear window b. Keep your hand at the _________________ of the steering wheel c. To move the trailer left, move your hand to the _________________ d. To back to the right, move your hand to the _________________

3. Backing a Trailer by Turning Steering Wheel in the Opposite Direction:a. To back to the left, turn the steering wheel to the rightb. Straighten the wheelc. Turn the wheel in the opposite directiond. Straighten the wheele. Turn the steering wheel to the rightf. Straighten the wheel and back the towing vehicle and trailer

4. Errors to Avoid When Backing:

a. Turning the steering wheel too farb. Holding the steering wheel in a turned position too long if trailer starts to

_________________

5. Essential Equipment for Towing:a. Additional equipment

Heavy-duty suspension Increased-capacity cooling system High-ratio axle Oversize mirrors

b. Emergency equipmentc. Trailer hitchd. Hitch ball

6. Connecting a Trailer:a. Ball and coupler combinations – sized correctly for tight fitb. Safety chains – crossed beneath the coupler and connected to the hitchc. Breakaway chains – hooked to hitch or frame memberd. Electrical connections – set up so lights function properly

7. Pre Trip Check:a. Attach tongue of trailer to hitchb. Snap locking mechanism c. Put lock pin in placed. Connect electrical wirese. Check Brakes and Lights

8. Loading a Trailer Properly:a. The rear of the vehicle should support 10 – 15% of the trailer load.b. Arrange _________ of weight in the front half of trailer and _________ in rear.

c. Make sure trailer is level.

9. Pulling Heavy Loads:a. The larger the load, the _________________ it will take to stopb. _________________ following distance and test your stopping powerc. Use caution d. Slow down

10. Jackknifing a Trailer:a. Common when backing – will damage the hitch and the trailerb. Occurs when angle between vehicle and trailer is less than ________ degreesc. Back slowly and keep steering wheel movements to a minimumd. If you get in trouble, pull _________________.