12
Weather Balloon Project ECE 298 TJ Sullivan Matt Salazar Curt Watson Team Members

Weather Balloon Project ECE 298

  • Upload
    red

  • View
    34

  • Download
    0

Embed Size (px)

DESCRIPTION

Team Members. TJ Sullivan. Curt Watson. Matt Salazar. Weather Balloon Project ECE 298. Structure: Plexiglass tube (5” wide & 1/8” thick) Lids are Plexiglass (5.1” wide .05 thick) Center (.5” inner hole, .25 wall) Insulation: Foam insulation tape Gold heat reflective film. - PowerPoint PPT Presentation

Citation preview

Page 1: Weather Balloon Project ECE 298

Weather Balloon ProjectECE 298

TJ Sullivan

Matt Salazar

Curt Watson

Team Members

Page 2: Weather Balloon Project ECE 298

THE CAPSULE Structure:P lex ig lass tube (5” wide & 1/8” th ick)L ids are P lexig lass(5.1” wide .05 th ick)Center ( .5” inner hole, .25 wal l )Insulat ion:Foam insulat ion tapeGold heat reflect ive fi lm

Page 3: Weather Balloon Project ECE 298

PICAXE DATA LOGGER

The PICAXE datalogger is a complete and pre-assembled 4 channel datalogger, supplied with PICAXE-18M2, LDR light sensor and digital temperature sensor. Uses easily expandable i2c EEPROM to store data, and additional sensors can be added as desired.

Page 4: Weather Balloon Project ECE 298

SENSORS Digital internal temperature sensor Digital external temperature sensor Barometer Accelerometer

Page 5: Weather Balloon Project ECE 298

EXTRAS Control heater through picaxe Control camera through picaxe

Page 6: Weather Balloon Project ECE 298

TEMPERATURE SENSORS

The DS18S20 i s a d ig i ta l temperature sensor that w i l l ou tput tempera tures be tween –55 to + 125 degrees Ce ls ius . Th i s makes i t s imp le to so lder to w i res o r p r in ted c i r cu i t boards

We ran an in te rna l and ex terna l tempera tu re sensor. We d id th i s so we wou ld know how we l l ou r capsu le was insu la ted . The in te rna l sensor wou ld be used to cont ro l our heate r and come on a t ze ro degrees Ce ls ius and tu rn off when i t wou ld go back above th i s t empera ture . Th i s wou ld be cont ro l l ed th rough p i caxe .

Page 7: Weather Balloon Project ECE 298

ACCELEROMETER (X/Y)

Dual ax is ±5g sense rangeUp to 312mV/g sens i t iv i tyOperat ing vo l tage 3 to 5VReverse vo l tage protect ionOvervo l tage protected up to 14VOutput short protect ionDraws under 2mA

Page 8: Weather Balloon Project ECE 298

BAROMETERPressure range:

300 to 11OOhPa (+9000m to 500m above sea level) Supply voltage:

1.8 ..... 3.6v (V0o4) 1.62V ...3.6V (VDoo)

Dimensions: 5.0mm L x 5.0mm W x

1.2mm H Low power:

5pA at 1 sample /sec. Power mode

0.O3hPa (0.25m I2C interface

Page 9: Weather Balloon Project ECE 298

HEATER:

Materials: *2 ceramic resistors*Fuse(2amp)*10K resistor*Transistor (2N2222)

Page 10: Weather Balloon Project ECE 298

We used this to ground the camera. It would turn the camera on and off as to conserve the battery. Now we could focus on what we felt would be the most interesting parts of the flight.

PODGIZMO:

Page 11: Weather Balloon Project ECE 298

Energizer Ultimate Lithium AA

Temperature range:-40 º F to 140º F

Weight:14.5g

BATTERY:

Page 12: Weather Balloon Project ECE 298

GOPRO HD HERO

Stats: 1080p: 1920x1080 p ixe l s (16 :9 ) , 30 fps , 15 Mb i t / s

data ra te960p : 1280x960 p ixe l s (4 :3 ) , 30 fps , 12 Mb i t / s data ra te720p : 1280x720 p ixe l s (16 :9 ) , 30 fps w i th 8 Mb i t / s data ra te ,o r 60 fps w i th 15 Mb i t / s data ra te