Allsteel Inc. Muscatine, lowa 52761-0071

3430462600 A (09/2019)

Wall Mounted Worksurface Installation Packet

www.allsteeloffice.com

IndexAttach Legs and Stiffeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1Cut Wall Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1Attach Worksurface to the Wall Mount Bracket. . . . . . . . . . . . . . . . . . Page 2 and 3Twine Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 and 4

3430462600 APAGE 1 OF 4 (09/2019)

Wall Mounted Worksurface Installation Packet

Illustration 1. Attach Legs and Stiffeners

Illustration 2. Cut Wall Mount Bracket

Tools:- Level- Drill- Hacksaw- 1/4” Driver- Extra tools/hardware appropriate for connecting mounting kit to the wall

Note: Customers to provide wall attachment hardware. For attaching to wall with wood studs: use 1/4" 3" long (minimum) wood screws into the studs and 1 “Molly” anchor between studs. For attaching to a wall with metal studs: suitable 1/4" “Molly” anchors are to be installed through the metal studs and drywall and 2 “Molly” anchors are to be used between studs.

An improperly installed wall mount kit and worksurface can fail and fall resulting in severe injury to yourself or others. Follow the important instructions below and all the installation guidelines in this instruction sheet: • Do not attach horizontal wall mount kit to masonry walls. • Use only Allsteel worksurfaces.

Note: When securing the wall mount bracket to the wall, it is necessary to connect to a minimum of three studs on worksurfaces 54" or less and four studs on worksurfaces greater than 54"

Step 1 - Assemble legs and stiffeners to worksurface according to Allsteel instructions (installation instructions provided with base or found on hniproductinstall.com). Do not flip worksurface until Step 3 has been completed.

Step 1 - Using a hacksaw, cut wall mount bracket to match the table width using the notches as a guide (dimensions below correspond to overall table width)

48"54"

60"

3430462600 APAGE 2 OF 4 (09/2019)

Illustration 3. Attach Worksurface to the Wall Mount Bracket to Wall

Illustration 4. Attach Worksurface to the Wall Mount Bracket

Wall Mounted Worksurface Installation Packet

Wall Mount Bracket

Leg

Height

Using appropriate fasteners (not provided), attach the wall mount bracket to the wall studs so that the top face of the bracket is equal to the leg height.

Wall

Wall Mount Bracket

Step 2 - With a minimum of two people, flip the worksurface upright and rest the back end of the worksurface on the wall mount bracket. Push the worksurface flush against the wall and center it on the bracket.

Note: Customers to provide wall attachment hardware. For attaching to wall with wood studs: use 1/4" 3" long (minimum) wood screws into the studs and “Molly” anchors between studs. For attaching to a wall with metal studs: suitable 1/4" “Molly” anchors are to be installed through the metal studs and drywall and 2 “Molly” anchors are to be used between studs.

Top Width

# of Studs

# of Molly Anchors Between Studs

48-54 3 260 4 2

3430462600 APAGE 3 OF 4 (09/2019)

Illustration 5. Attach Worksurface to the Wall Mount Bracket

Wall Mounted Worksurface Installation Packet

48" Table Shown

Step 3 - Using a Philips driver and the 3/4” long screws provided, attach the worksurface to the wall mount bracket.

111” Pan Head Phillips Screw

1. Identify appropriate twine and minitap configuration on “Twine Configuration Guide.”

2. Using screws provided, attach minitap unit(s) flush with the edge of the worksurface.

3. Attach the node retainer bracket(s) in the approximate locations on the “Twine Configuration Guide.” Snap the nodes into place.

4.

Bundle and secure any excess cords to the bottom of the work surface as needed.

Node

Node Retainer BracketMini Tap

Illustration 6. Twine Electrical Installation:

3430462600 APAGE 4 OF 4 (09/2019)

Wall Mounted Worksurface Installation Packet

Twine Model Number Module Qty

A AMPTUSPS1A/U 1B AMPTUSPS2 2C AMPTUSPL3 3D AMPTUSPS4 4E AMPTUSPM4 4F AMPTUSPL4 4G AMPTUSPXL4 4

A

B

CD

E F

G

Wall Mounted Worksurface Installation Packet

3430462600 APAGE 5 OF 5 (09/2019)

Illustration 7. Pop-up Power Caddy Installation1. See Pop-up Power Caddy instruction for metal spring

spacer placement and plastic retainer clip installation.2. To install Pop-Up Power Caddy:

• A. Route Pop-Up Power Caddy cord, set Power Caddy into hole in worksurface.• B. Run cord along underside of worksurface to base or wire management solution.

A

B