Wall Mot Manual Eng

7/25/2019 Wall Mot Manual Eng

1/23

Hfele GmbH & Co KG 1

MOT - Multi Output TerminalTerminal data sheet

The Dialoc Multi Output Terminal !MOT" is based on the Dialoc terminal firm#are of$ersion % 'n (eneral it is compatible to a standard )T in follo#in( features*

Compatible to the Dialoc s+stem*,tand lone,.Hotel !#ithout indi$idual (uest room support"

Clinic !#ithout indi$idual (uest room support"/ni$ersal !#ithout indi$idual (uest room support"0ersonnelOnline s+stem !0ersonnel Hotel"

Multie+ support* /p to 2 lo(ical e+s on one transponder Macro pro(rammable

MOT specific macros supported b+ DMD 3 114 or hi(her 56tended 0ersonnel Ke+ !70K" 5as+ confi(uration #ith ,pecial 8unction Transponders More comfortable confi(uration #ith 0arameter Transponders Dia(nostic parameters

Onl+ one firm#are for T'9', :5G'C and Ta(-'t;',O $ersion because of separatedintelli(ent readin( unit

Ke+ stamps for realisin( usa(e count;chec Output timers for realisin( output acti$ation in a sort of


2/23

Hfele GmbH & Co KG ?

Principle of access rights at the MOT

The (eneral access ri(hts of the MOT are confi(ured accordin( to the correspondin(Dialoc s+stem*

, s+stem*:earnin( , e+s

0ersonnel s+stem*0ersonnel (roup confi(uration #ith 0ersonnel soft#are and transfer of data b+ oneof the follo#in( options*- ,er$ice soft#are and MD/- ,er$ice soft#are online or #ith MD/ '9-don(le

- 0arameter e+ Hotel s+stem

,ettin( (uest options b+ one of the follo#in( options*- ,er$ice soft#are and MD/- ,er$ice soft#are online or #ith MD/ '9-don(le- 0arameter e+Optionall+ the (uest e+ $alidation can be done (eneration-controlled @ut thisshould onl+ be done #hen it can be ensured that nearl+ all (uest reall+ use theterminal Other#ise the (enerations ma+ not be actuali>ed and are not $alid #henmore than 1A (uests in a ro# are not usin( the terminalB

The confi(uration of the access ri(hts for floors or special ele$ator functions !e6 priorit+ oremer(enc+ s#itches" is based on rules rule has follo#in( parameters*

9an(e of outputs ; rela+ s#itches !ele$ator* floors" for #hich the rule applies't has to be a coherent ran(e - no (aps are allo#ed )hen there are (aps then anadditional rule #ith another ran(e is needed

ccess condition of ruleThere are follo#in( possible conditions*


3/23

Hfele GmbH & Co KG

SA Key - ID numbers, 'D number has to be #ithin a (i$en ran(e !A?%%" , s+stem

Guest keys - oom numberGuest e+ number has to be #ithin a (i$en ran(e of room numbers!1EEEE"

Hotel s+stem

Guest ke - oom ! key number"not at ele#ator terminal$Guest room and e+ numbers ha$e to be identical #ith the (i$en$alues

9oom number* 1EEEKe+ number* 12

Hotel s+stem#ith multiple occupation!e6 clinics"

Guest keys - Option flag "stan%ar%$t least one of the specified (uest options has to be setThe $alue is interpreted bit#ise

Hotel s+stem

Guest keys - Option #alue3alue of (uest e+ option has to be #ithin a specified ran(e !A"

Hotel s+stem

&isitor keys - Option flagt least one of the specified (uest options has to be set

Hotel s+stem

Maintenance keysMaintenance e+ number has to be #ithin a (i$en ran(e of room

numbers!1EEEE"

Hotel s+stem

Personnel keys - Key numberKe+ number has to be #ithin a (i$en ran(e !1AAAA"

0ersonnel s+stem

Personnel keys - Group numberGroup number has to be #ithin a (i$en ran(e !A?4A"A stands for


4/23


Time )one startCondition (ets true once at start of specified time >one

an+ Dialoc s+stem

Time )one en%Condition (ets true once at end of specified time >one

an+ Dialoc s+stem

During time )one"all *+s$This rule action is done e$er+ 14 seconds #hen specified time >oneis $alid

an+ Dialoc s+stem

Digital input con%ition,tate of di(ital inputs must ha$e a specified pattern

an+ Dialoc s+stem

Macro rule %efinitionThis rule condition can be acti$ated b+ macro pro(ramThere can be up to ?44 different rules to be acti$ated b+ macro!Macro ,tate ,et 1")ith this rule it is possible to set the specified outputs toanothern open time than the standard open time or to setthem to special loc states

an+ Dialoc s+stem

Time >one condition of the ruleThere is no time condition

oractual time has to be #ithin one of the 2 time >ones

ction to perform #hen rule is $alidThis specifies the rela+s contact state

1 off

? on

c+cle!#ith standard open time"

2 to((le

The rules are stored to(ether #ith the e+s in the e+ memor+ of the terminal 5ach ruleneeds as much memor+ as one e+ ! b+tes"

Operation of OT' "output e,ten%er$ outputs an% .Ds

ll output contacts are operated b+ independent timers #hen c+clin( This means that

another contact can be acti$ated b+ another access condition as soon as one contact #asacti$ated timer is


5/23


The output timers ha$e a duration tolerance of ma6 -1 sec dependent on the moment ofstart of acti$ation

,o it is (ood practice to define the openin( time at least 1 second lon(er than needed

The :5Ds at the readin( unit are s#itched as follo#s* (eneral access ri(ht of a e+ is si(naled b+ in$ertin( the (reen :5D state for Ams)hen at least one OT7 output is acti$ated for the specified open time then the (reen :5Dis s#itched on for that time 0ermanentl+ acti$ated outputs !e6 to((led outputs" are not

sho#n b+ (reen :5DThe :5D control can be deacti$ated b+ macro pro(ram #ith the macro

? @linin( !OT7 outputs are alternatin( all acti$ated ; all deacte$ated ",peed appr ? H>


6/23


7/23

Hfele GmbH & Co KG %

Opentime for 45ycle4 operation

The ma6imum open time is ?2A sec Hi(her $alues ma+ cause errors

,tandard time is 4 sec

Au%it trail

udit trail entries are made #ithout report of the loc state because this cannot be

specified for all rela+ outputs ,o the audit trail onl+ reports the usa(e of e+s - not #hichor if an+ output contacts #ere acti$ated

MOT specific configuration parameters

elay 65This parameter has to be set #hen rela+s #ith =C contacts are used)hen acti$ated all rela+ output states are in$erted*

elay 65 "normally close%$In#ert OT' output acti#e states

Outputinacti#e state

Outputacti#e state

0arameter not checed !standard" 9ela+ not po#ered 9ela+ po#ered

0arameter checed 9ela+ po#ered 9ela+ not po#ered

7se main relays/se rela+s on main control unit as OT7 1@+ settin( this parameter the first 2 outputs are redirected to the 2 rela+s on themain control unit The outputs 4- are not a$ailable then

@e(innin( #ith ouput E all follo#in( outputs are on OT71 and further cascadedOT7

6umber of OT'The the number of connected OT7 has to be setThe ma6imum number is 1 the minimum number is 1)hen the rela+s on the main control unit are used then this counts as one OT7


8/23

Hfele GmbH & Co KG

MOT configuration

dditionall+ to the standard confi(uration #ith terminal parameters the MOT has to be

confi(ured b+ acces rules #hich are stored in the terminals e+ list These rules data hasto be created #ith the MOT Confi(uration soft#are

The most comfortable #a+ to confi(ure a MOT is to do it #ith a terminal data base b+ theDialoc ,er$ice soft#are The confi(uration data can then be tranfered to the terminal b+MD/ !1A or hi(her" or b+ online connection

There is follo#in( alternati$e possibilit+ to confi(ure a MOT after definin( the confi(uration#ith the MOTCO=8'G pro(ram*

56port the MOT rules to a D0K file :oad this file into the e+ list menu in Dialoc ,er$ice soft#are !0C @eam menu" Then the rules can be transferred b+ online connection to the MOT or can be

pro(rammed to a parameter transponder !ma6 14 rules"

MOT macro programming

8ollo#in( macros are specific for the MOT*

Macro5omman%

IDParameter /unction

Do ction ? -,ets output e6tender accordin( to the bits of391

Do ction -MOT buffer to OT7,et OT7 to actual state of buffer

,tate ,et 1MOT macro rule

'D !A?44",et buffer accordin( to specified macro rule

,tate ,et ?

A* ll off1?2A* Open time?4?* To((le?4* Off loced?42* On loced?44* Onpermanentl+

,ets complete buffer to specified $alue

,tate is set in buffer To tae place at outputsthe macro Do ction must be called


9/23

Hfele GmbH & Co KG E

,tate ,et

A* Off1?2A* Open time?4?* To((le?4* Off loced?42* On loced?44* Onpermanentl+

MOT set output specified b+ 391 to specified$alue391* A1?% A is first output,tate is set in buffer To tae place at outputsthe macro Do ction must be called

To((le does not chan(e outputs #ith


10/23

Hfele GmbH & Co KG 1A

9ar%:are :iring %iagrams

MOT main control unit


11/23


7sing optically %ecouple% inputs I6* - I6;

Principle interconnection of components


12/23

Hfele GmbH & Co KG 1?

5onnections at OT'

Schematic of MOT :iring


13/23


sp

ecial application of the MOT is the access control for floors in an ele$ator 'n thisapplication the MOT is also named as Dialoc 5le$ator Terminal !D5T"

The Dialoc 5le$ator Terminal !D5T" is desi(ned for controllin( access to the floor selectbuttons of an ele$ator )hen a e+ is presented to the D5T reader inside the ele$atorcabin then all b+ Dialoc authori>ed floors select buttons are enabled b+ rela+s

The D5T consists of follo#in( components*

Transponder 9eadin( /nit !T'9', :5G'C or ',O;Ta('t"Optionall+ a D5T can be operated #ith up to 2 readin( units

MOT Control /nitOptionall+ the 2 relais of this control unit can be used

optional* /p to 1 Output 56tenders !OT7"5ach OT7 can be connected to ma6 floor selection buttons'n total the D5T is able to control the access of ma6 1? floors

The positionin( of Transponder 9eadin( /nit the Control /nit and the Output 56tender!s"depends on the space a$ailable in cabin and on the location of the ele$ator control room

The cable t+pe and len(th has to be carefull+ selected

Dependend on the application the rela+s of the OT7 can be connected in parallel or inserial to the floor selection buttons To fall into a sa$e state in case of failure of the D5T anappropriate #irin( to rela+ contacts should be done*

D5T - Dialoc 5le$ator Terminal


14/23


.nabling of floor select button by D.T

)hen presentin( a e+ to D5T all floor select buttons are enabled to #hich the o#ner ofthe e+ has access ri(hts The user has to press the floor button to select his #anteddestination floor

.nable% on D.T failure

The rela+ is connected in serial to the floor selectbutton

The OT7 must ha$e the


15/23


.nable% on D.T failure

The rela+ is connected parallel to the floor selectbutton

The OT7 must ha$e the


16/23


specified ran(e of rela+s is set #hen all follo#in( conditions are true*

Ke+ is of the reIuired t+pe!e6 (uest e+ room number ran(e personnel e+ number ran(e "

,pecified time >one is $alid !>one 12 or al#a+s"

MOT 5onfiguration soft:are

The MOT confi(uration soft#are is installed to(ether #ith the Dialoc ,er$ice soft#are!Dialoc ,er$ice ?A or hi(her"'t can be started directl+ or it can be started b+ Dialoc ,er$ice for comfortabel

confi(uration of a MOT in the terminal data baseThe pro(ram MOTCO=8'G is for definition and $isualisation of MOT access rulesMOTCO=8'G creates a parameter defnition file !D9C" and a rules definition file !ta( file666-?1TTG" These files are located al#a+s in the TDT director+

Multi Output Terminal Confi(uration

9o: to configure an MOT in the Dialock System


17/23

Hfele GmbH & Co KG 1%

4 ,et up a terminal data base

The MOT has to be defined in the terminal data base #ith the accordin( terminalcate(orie !#ith terminal t+pe MOT")hen a MOT terminal is selected in terminal list then the


18/23


D5T - Dialoc 5le$ator Terminalpplication 56ample

8ollo#in( a description of reIuirements for an ele$ator terminal in a hotel 't is a hotel #ith?4 floors and special access ri(hts for (uests and personnel #ith time >ones

/loors * - +1

5$er+bod+ can access these floors b+ pressin( one !or more" of the buttons 1 to 4=o time restrictions

/loors > - *?@ =; an% =+1

'n the time bet#een A*AA and ??*AA e$er+bod+ can access these floors b+pressin( one !or more" of the buttons - 1E ?2 and ?4

'n the time bet#een ??*AA and A*AA (uests ha$e to present their Ke+ to thereader fter presentin( the Ke+ the button of the correspondin( floor is acti$atedautomaticall+ 't is not possible to (o to a different floor than the


19/23

Hfele GmbH & Co KG 1E

D.T configuration for these re8uirements

8ollo#in( basic settin(s ha$e to be done*

?4 floors reIuire 2 OT7 =o usa(e of rela+s on main control unit =O !normall+ open" rela+s are used Hotel and 0ersonnel s+stem 9ela+ acti$ation time is 4 sec One time >one is used !an+ da+ *AA until ??*AA" ll rela+ contacts are named #ith the accordin( floor number

5onfiguration of relay s:itches

ll floor select buttons of the ela$ator are connected in serial to the OT7 rela+ contactslthou(h floors 1 to 4 do not reIuire an access control the+ should also be #ired becausethis allo#s eas+ chan(es of access ri(hts later ,o the rela+s for floors 1 to 4 ha$e to be

enabled all the time ll other floors ha$e e+ and time dependent access rules


20/23

Hfele GmbH & Co KG ?A


21/23

Hfele GmbH & Co KG ?1

8ollo#in( the main #indo# #ith the


22/23

Hfele GmbH & Co KG ??


23/23

Documents

Wall Mot Manual Eng