Wal-Mart Universal Monitor Stand Installation Manual › wp-content › uploads › 2017 › ... · Walmart Universal Monitor Stand Conversion\Installation Instructions 26 Mounting

$Page 1: Wal-Mart Universal Monitor Stand Installation Manual › wp-content › uploads › 2017 › ... · Walmart Universal Monitor Stand Conversion\Installation Instructions 26 Mounting$
Wal-Mart Universal Monitor Stand

Installation Manual

CIM 2122 10/14/16

Walmart Universal Monitor Stand Conversion\Installation Instructions

1

Refer to the illustrated instructions below to convert the Universal Monitor Stands from Single

to Dual version, and Left Hand to Right Hand versions for both Mainline and Speedy check lanes

– before installing on the conveyor or cabinet.

Attachment hardware is included with each Universal Monitor Stand. Refer to the hardware

specifications on page #3.

The Universal Monitor Stand will be shipped as a Single Monitor Left Hand Version (as shown

below). To convert the Monitor Stand to a Dual or Right Hand (Mainline or Speedy) version,

follow the appropriate instructions designated for each configuration.

If you require assistance with the conversion or installation, please call the Pan Oston Field

Operations Department at 1-800-472-6678.


2

Configuration Reference Page

Version Page

BM-132895-KIT Universal Accessory Kit 3

QR Code Information 4

Hardware Kit \ Tools Required 5

Convert Single Left Hand Stand to Single Right Hand Stand 6 - 14

Convert Single Monitor Stand to Dual Monitor Stand (Left \ Right Hand) 15 - 21

Installation of Monitor Stand to belted Check lanes 22 - 23

Installation of Monitor Stand to Speedy lanes 24 – 29

Installation of Monitors and EFT Card Reader 30 - 32


3

BM-132895-KIT Article Number: 100590296


4

QR CODE INFORMATION The checkout lanes and accessory kits have a QR code that may be read with a standard QR

codereader app on a cell phone. The purpose of the QR code is to provide a link to

documentation pertaining to the installation of the checkstands.


5

Universal Monitor Stand Hardware Kit

The Hardware Kit is made up of machine screws and star washers designated for the

components that are to be removed or repositioned depending on the different configurations

(Single or Dual Monitor, Left Hand or Right Hand, Belted or Speedy Lanes) . Refer to the

installation instructions below in regard to the correct hardware required. A Square head drive

and Phillips head screwdriver will be needed to perform this installation.

Quantity of 2

¼-20 x 1 ¼

Machine Screw

Quantity of 8

¼-20 x ¾”

Machine Screw

Quantity of 8

M4 x 12mm

Machine Screw

Quantity of 10

1/4” Star Washer


6

Universal Monitor Stand – Single Left Hand

Follow the steps below to convert the Single Left Hand version to the Single Right

Hand version.


7

STEP 1: Remove the (7) ¼-20 machine screws\washers, from both sides and top, which attaches

the existing check shelf to the monitor base. Relocate the check shelf to the opposite

side of the monitor base to create a Right Hand version.

Check Shelf

Monitor Base

(7) Mounting Screws\Washers


8

STEP 2: Mount the check shelf to the opposite side of the Monitor Base – using the same (7) ¼-20”

machine screws \ washers previously removed in STEP 1.


9

STEP 3: When converting the Monitor Stand from a Left Hand version to a Right Hand version, the check shelf must be repositioned to have the overhang on the side opposite the EFT Pull Bracket (as shown by the arrows below). NOTE: The overhang position is standard regardless of orientation (Left Hand or Right Hand). Using a Phillips head screwdriver, remove the (2) mounting screws that attach the Policy Cover to the Check Shelf, then remove the Policy Cover.

Policy Cover mounting

screws


10

STEP 4: Remove the (4) ¼-20 x 1” machine screws that attach the Check Shelf to the Monitor Base, then

reposition the Check Shelf where the overhang is opposite the EFT Pull Bracket – then reattach

with the same hardware as was removed.

Insert mounting screws

into the (4) holes shown


11

STEP 5: Reposition the Monitor Extension Bracket to attach directly to the Monitor Base by first

removing the (4) ¼-20 x ½” mounting screws\washers (as shown below).


12

STEP 6: Remove the (4) ¼-20 x ½” machine screws\washers that attach the Monitor Extension Bracket to

the Monitor Base.


13

STEP 7: Reattach the Monitor Mount to the Monitor Base using the same (4) ¼-20 x ½” machine screws

\ washers previously removed.


14

The Single Right Hand Monitor Stand will look like this upon completion of the conversion. Repeat the

above Steps in reverse order to convert back a Single Right Hand Monitor Stand.

Universal Monitor Stand – Single Right Hand Version


15

Universal Monitor Stand – Single to Dual ( Left Hand Version)

Follow the steps below to convert the Universal Monitor Stand - Single Left Hand version to the

Dual Left Hand version. Refer to the Single Left to Single Right Hand instructions on pages (4

through 12) to reposition the Check shelf and Monitor plate (Cashiers side)

STEP 1: Reposition the Check Shelf to the extended position by first removing the (7) ¼-20 x ½” machine

screws \ washers (as shown below).


16

STEP 2: Extend the Check Shelf outward and align the mounting holes with the open threaded rivet nuts

at the end of the Monitor Base. Attach the Check Shelf to the Monitor Base using the (7) ¼-20 x

½” machine screws previously removed.


17

STEP 3: Remove the (4) # 8-32 x ½” machine screws that attach the EFT Pull Bracket to the EFT Riser

Bracket as shown – then remove the EFT Riser Bracket to access the additional (4) screws that

attach the EFT Pull Bracket to the Monitor Base.

Mounting Screws


18

STEP 4: Remove the (4) #8-32 x ½” machine screws that attach the EFT Pull Bracket to the Monitor Stand

Base.

Mounting Screws


19

STEP 5 : Align the (4) mounting holes on the Monitor\EFT Bracket, with the (4) threaded rivet nuts on

the Monitor Stand Base.

STEP 6: Attach the Dual Monitor plate to Monitor Stand Base using the (4) #8-32 x ½” machine screws

removed in STEP 4.

Rivet Nuts


20

STEP 7: Attach the EFT Riser Bracket to the Monitor\EFT Bracket using (4) #8-32 x ½” machine screws

which are attached from behind (as shown below).

Attach EFT Riser Bracket from the back side


21

STEP 8: The EFT ISD Adaptor Plate is NOT included as part of the Universal Monitor Stand or Hardware

Kit from Pan Oston. This plate and EFT mounting hardware is supplied by Walmart ISD

STEP 9: Attach the EFT Adaptor Plate to the EFT Riser Bracket using (4) #8-32 x ½” machine screws.

EFT Adaptor Plate

Mounting screw locations


22

Mounting the Universal Monitor Stand Base to the Belted Conveyor

STEP 1: Place the Monitor Stand Base over the scanner end of the rail on the conveyor, aligning

the inner sets of both slots (refer to the RED arrows for proper alignment) – with the

3rd and 4th hole locations.

Scanner End


23

STEP 2: Attach the Monitor Stand Base to the conveyor by using (2) ¼-20 x ¾” machine screws

on EACH side of the rail. From the scanner end of the conveyor, use the 3rd and 4th

hole locations - on each side – as stated in STEP 1 above.

Outer Mounting Screw Locations

Inner Mounting Screw Locations


24

Mounting the Universal Monitor Stand Base to the Speedy Cabinet

STEP 1: Place the Monitor Stand Base over the scanner end of the rail on Speedy cabinet,

aligning both inner sets of slots (refer to the illustrations below for proper alignment) –

with the 1st and 2nd rivet nuts.

From the customer

side (Left) – align

2nd slot with 1st rivet

nut.

From the customer side

(Right) – align 2nd slot

with 3rd rivet nut


25

STEP 2: Place the Rail Extension into the opening at the intake end of the Monitor Stand.

Ensure the end of the Rail Extension is flush with the end of the Monitor Stand. Attach

the Rail Extension to the Monitor Stand using (2) ¼”-20 x ¾” machine screws. (refer to

the illustrations below for proper alignment).

Rail Extension is to be flush

with Monitor Stand


26

Mounting the Touch Screen Monitor on the Cashier Side (Single or Dual Monitor)

STEP 1: Place \ align the mounting holes on the backside of the monitor with the mounting

holes on the Monitor Stand plate and attach with (4) #8-32 x ½” machine screws.

Monitor mounting hole

locations


27

Mounting the Touch Screen Monitor on the Customer Side (Dual Monitor Only)

STEP 1: Place \ align the mounting holes on the backside of the monitor with the mounting

holes on the Monitor Stand plate and attach with (4) #8-32 x ½” machine screws.

Monitor mounting hole

locations


28

STEP 2: Route the cables for the monitors (Single and Dual) through the opening in Mount Extension

into the scanner well area.

Opening for Monitor

Cable Routing


29

Mounting the EFT Card Reader on the Customer Side (Single or Dual Monitor)

Refer to the ISD EFT Plate instructions for EFT mounting

Mounting the LED Customer Display (Single Monitor Only)

STEP 1: Before mounting the LED Display to the Monitor Base Stand it will be necessary to

feed the cables through the routing holes as shown below.

Cable Routing Path


30

STEP 2: Mount the LED Customer Display to the Monitor Stand Base by using (2) ¼-20 x 1 ¼”

machine screws

Cable Routing Path


31

Completed Dual Monitor Stand Version

Customer Side

Cashier Side


32

Completed Single Monitor Stand Version

Cashier Side

Customer Side

Documents

Wal-Mart Universal Monitor Stand Installation Manual › wp-content › uploads › 2017 › ... · Walmart Universal Monitor Stand Conversion\Installation Instructions 26 Mounting