15). After connection, it automatically adjusts to USB network Joystick setting

state of the last time.

16). Save all USB network Joystick settings in files.

2. Wireless Transmission Connection

1). Connect the receiver to the corresponding port of the console/computer,

the power LED indicator on the receiver light continuously and signal LED

indicator flashes;

2）Install batteries into the gamepad, it connects with the receiver if the

signal LED indicator on both the receiver and the gamepad turn into keep-on

from flashing.

3）In case of connection failure, check if the port of the console/computer

works. Re-turn on the gamepad, or re-connect the receiver to the

console/computer.

3. Special Functions

1). The two installed brand new motors brings good vibration effect if only the

game supports vibration (On computer, driver is needed.);

2). Sleeping mode (Power Saving Mode)

In order to save power and lengthen the using life of batteries, a power

saving system is designed in the wireless gamepad. The gamepad turns into

sleeping mode (power saving mode) under the following conditions:

A. If there is no operation within 30 seconds since the connection between

the controller and the receiver, the controller will turn into sleeping mode (power

saving mode).

B. There is operation since the connection between the controller and

receiver. If there is no operation for 5 minutes, the controller will turn into

sleeping mode (power saving mode).

Press【Start】button can stop this sleeping mode (power saving mode).

3). Low power alarm system

When the batteries are going to be out of power, the power LED indicator will

flash once per second to remind you of low power, and you need to change

batteries.

4). Modes shift function (It is applicable for PS1, PS2 and PC.)

Shift between digital and analogue modes.

-2--1-

WIRELESS GAMEPAD INSTRUCTIONSI.Product Photo

II.Package Contents.

III.Product Description

1. Gamepad X 1 PCS.

2. Receiver X1 PCS.

3. Driver disk X 1PCS.

1.Functions

1). Professional design, delicate outlook, comfortable feeling.

2). RF2.4G wireless technology, receiving range is up to 5-20 meters.

3). Installed double vibration feedback motors

4). Power saving mode (Sleeping Mode)

5). Alarm of low power.

6).Two modes for choice: digital mode and analogue mode. Can shift between the

two modes freely.

7). 8 way directional joysticks which work under both digital and analogue modes.

8). Connecting and modes shifting LED indicators

9). Motors on-off function

10). Power switch

11). Powered by 4 external batteries (AAA DC:1.2-1.5V)

12). Compatible with PS1, PS2, PS3 consoles and PC/computer operation systems

(WIN98 /ME/ 2000/ XP/ VISTA/ WIN7) with corresponding receivers.

13). 12 buttons, 1 point of view hat.

14). PC wireless game pad is Programmable. (The functions of the gamepad

buttons can be setted freely and can replace the keyboard and the mouse functions)

PS2/PS3/USB 3 IN 1 GAMEPAD MINI USB GAMEPAD

2) . 【Joy_Setup】 and 【Game Control ler】 icons as shown in Diagram 2 appear

on the desktop after the instal lat ion.

Diagram 2

A. 【Joy_Setup】: the shortcut to enter program sett ing.

B. 【Game Control ler】:shortcut to enter Joyst ick test ing

interface.

2. Un-instal lThe

USB Network Joystick is with self unload function. Players can delete all the

USB Network Driver f i les, program package and shortcuts. Cl ick【SART】-【CONTROL PANEL】-【ADD/DELETE】 to open the 【USB Network Joystick (BM)】instal ler. Then un-instal l or delete the USB Network Driver quickly following the

prompts.

1.Test

1）Start testing set up interface with the following two methods:

A.Double-Click the shortcut icon【Game Controller】on the desktop as shown in

Diagram 2;

B.Cl ick 【Start】-【Control ler Panel】-【Game Control ler】Window as shown in Diagram 3 would appear after the start of 【Game Controller】.

VI.Test and Program Settings

Diagram 3. Game Controllers

-4-

A. Digital mode: Under digital mode, the mode LED indicator is off, and the

analogue button is out of function. The left 3D joystick has the functions of the

directional buttons, while the right joystick has the same functions as the △、

○、X、□ fire buttons;

B. Analogue mode: Under analogue mode, the model Led indicator keeps on.

Press MODE button can shift to analogue mode from digital mode.

5). Motor ON/OFF function

Press SELCT + R3 (9+12) buttons can turn on/off the motors vibration function.

The motors vibration function turns off automatically when power is low.

Configuration Requirements:

1. Operating System: win98/ win2000/ win XP/ vista/ win 7;

2. Software requirements: Above Direct 7.0;

3. The Minimum configuration:

1). CUP: Above Pentium 166Mhz;

2). Computer memory: Above 128MB;

3). Display card: Standard VGA+ Above 256 color mode;

4). Hard disk: meeting the operational requirements of the operating system;

5). Other requirements: Keyboard, mouse, monitor, USB interface.

IV.Installation on Computers

1. Install

1）.【My Computer】-【DVD Driver】-【0523_USB_Network_Joystick_V203】,Double click 【0523_USB_Network_Joystick_V203】. Follow the tips to finish the

installation as shown in Diagram 1.

V. Install and Un-install the Driver

Diagram 1. Install USB

Network Joystick

-3-

2). 【Mouse】(refer to 【1】in Diagram 9):

A. Select 【Left joystick】 and click【OK】 to replace the mouse function with the

left stick of the joy pad. The directional buttons have the functions of mouse.

B. Select 【Right Joystick】 and click【OK】 to replace the mouse function with

the right stick of the joy pad.

C. Select 【None】 and click 【OK】 the sticks do not have Mouse function.

3).【Key send】(refer to 2 in Diagram 9):

A. Select 【one by one】 and click 【OK】 to set the controller buttons work only

one time when pressed.

B. Select 【Concurrent】 and click 【OK】 to set the controller buttons with turbo

function. ( The buttons works continuously when being pressed.)

4). 【Mouse Slow Fast】 ( refer to 3 in Diagram 9):

Click and drag the slider and click 【OK】to adjust the speed of Mouse function on

the controller.

5).To set the keyboard and mouse function to the controller buttons:

Select any key on the controller as shown in Diagram 8, and select 【Mouse】, 【Button map】, 【Keyboard setup】 or 【Clear】 in the drop-down list to set the

keyboard and mouse functions to the controller buttons.

A. 【Mouse】: set the Mouse key functions to the controller buttons.

B. 【Button map】: set the other buttons of the controller function to the selected

button.

C.【Keyboard setup】: set the keyboard keys function to the selected controller

buttons.(Note: Each controller button can replace 16 keyboard keys in maximum.)

D.【Clear】: clear the replacement functions of the selected buttons.

Diagram 9

-6-

2). Click 【Properties】in 【Game Controllers】 shown as Diagram 3 to start the

test interface as shown in Diagram 4.

　3). Test the controllers' functions of axis, buttons and point of view under 【

Function Test】as shown in Diagram 4.

　4). Under【Calibration Function】, the axis can be calibrated. Click 【Default】the

buttons functions would return to initial state, while click 【Set】 the buttons function

would turn to standard states as shown on Diagram 5.

Diagram 4. Test Interface Diagram 5. Calibration

5). Test the vibration function under 【Vibration Test】as shown in Diagram 6 .

Diagram 6. Vibration Test

2. The keyboard and Mouse Settings

　1). Click 【Joy_Setup】 as shown in Diagram 2 or click the 【Mouse Keyboard

Setup】as shown in Diagram 7 under 【Vibration】as shown in Diagram 4 to enter

the programming settings as shown in Diagram 8.

Diagram 7.

Diagram 8

-5-

For example: to set button【1】on the controller with the function of key【A】 of

the keyboard, first select button【1】of the controller as shown on diagram 8.

Second, select 【Keyboard setup】in the drop-down list to enter the setting up

interface as shown in diagram 10. Then select 【A】on the keyboard and click【OK】as shown in diagram 10. Then Button【1】of the controller has the function of of

key【A】of the keyboard.

After setting, the button turn to green, and beside it are the keys of the keyboard it

can replace.

Diagram 10

6). Click 【Save】 as shown in diagram 11 and diagram 12 to save the settings

in 【.pro】 file.

Diagram 11

-7-

Diagram 12

7). Click【Load】as shown in diagram 13 and diagram 14 can open and load the

settings 【.pro】file.

Diagram 13

-8-

Diagram 14

8). Click【Clear All】as shown in Diagram 15 all the buttons function return to the

default state.

Diagram 15

1. Before proper installing the right driver, some of the gamepad functions may not

works properly. Please uninstall the exist driver and install the right driver.

2. If any buttons can not work properly during games, please check the settings of

the gamepad.

3. The mini USB wireless receiver only works on computer, can not work on work

on consoles.

4. Please set the gamepad before your games.

5. If there is no vibration during games, please check if the game support vibration.

6. Use the gamepad at room temperature (5 °C—35 °C). Avoid using it in the

environment of high temperatures, high humidity or direct sunlight.

7. Do not let liquid or small particles to get into the gamepad.

8. Do not put heavy objects on the gamepad.

9. Never disassemble or modify the gamepad.

10. Do not bend, throw or drop the gamepad or subject it to the strong physical

shock.

-9-

11. When cleaning the gamepad, use a soft, dry cloth. Do not use paint thinner,

solvents or other chemicals.

-10-