Upload
lehanh
View
250
Download
3
Embed Size (px)
Citation preview
1
Volute Centrifugal Pumps PN 16 / PN 25for Heat Transfer MediaTheraml Oil up to 350 °CHot Water up to 207 °C
ALLHHEEAATT®
Series NTWH/CTWHprocess model
Series NBWH/CBWHblock model
Series NIWH/CIWHin-line model
ApplicationFor circulating heat transfer media such as thermal oil or hot water inheat transfer systems (DIN 4754 and 4752). The media to be pum-ped may not contain any abrasive constituents or chemically attackthe pump material.
SeriesAll series may be used with organic and synthetic thermal oils at tem-peratures of up to 350°C.The series NTWH, NBWH and NIWH (PN16) can be used with hotwater at temperatures of up to 183 °C and series CTWH, CBWH andCIWH (PN25) at temperatures of up to 207 °C.The application limits with regard to temperature, pump series andhousing material are specified in the table "Application limits" and inthe diagram "Pressure/ temperature limits depending on the housingmaterials”.
DesignSeries NTWH/CTWH:
Process models of a horizontal volute centrifugal pump. Single-flow, single-stage with optimised bearing support (consisting ofhousing cover incl. throttle/cooling section and bearing support).Shaft bearing consisting of a silicon carbide or carbon slidingbearing lubricated by the pumped medium on the pump side anda grease-lubricated deep groove ball bearing on the drive side.Spiral casing with cast-on pump feet.
Series NBWH/CBWH:Block model of a volute centrifugal pump. Single-flow, single-stage with optimised bearing support (consisting of housingcover incl. throttle/cooling section and bearing support).Plug-in shaft and motor shaft are rigidly connected to each other.Shaft bearing consisting of a silicon carbide or carbon slidingbearing lubricated by the pumped medium on the pump side andthe grease-lubricated deep groove ball bearing of the drivemotor. Motors with axial thrust bearings.Spiral casing with cast-on pump feet.Horizontal or vertical installation, however, not with motor arran-gement facing downwards.
Series NIWH/CIWH:In-line model of volute centrifugal pump, other details as for seriesNBWH/CBWH.
Shaft sealUncooled, balanced or unbalanced, maintenance-free mechanicalseals acc. to DIN 24 960.A safety gland and a subsequent throttle/cooling section are providedupstream of the shaft seal.
FlangesFlange connection dimension correspond to EN 1092-2, PN 16 or PN 25.
Performance data at 50 Hz
➀ The entry pressure and pressure during zero flow rate may not exceed thespecifed values. for permissible values per series, see diagram on page 2.
The mentioned performance data are to be considered as a product and perfor-mance abstract only. The particular operating limits can be taken from the quo-tation or order acknowledgement.
➀ Requirement to hot water quality: Water with low salt content or deionised water acc. to VdTÜV Directive 02.89 TCH 1466 solids content ≤ 5mg/l,without settling additives.
➁ Toxic thermal oils are not hermetically sealed from the environment. In this casewe recommend the use of our magnetically coupled pumps.
Series NIWH/CIWHSeries NBWH/CBWH
Series NTWH/CTWH
permissible internal pump pressure ➀
max. pump output max. pump heat
p [bar] Q [m3/h] H [m]
NTWH 660 100NBWH 270 92NIWH 220 92
CTWH 300 145CBWH 240 63CIWH 105 58
≤ 16
≤ 25
Series
Product Materialcode code
DIN 24 960
U2.11Abalanced
mechanical Counter ring SiC, silicone carbide Qseal O-ring Rubber fluoride (FPM) V
U3.3A Spring CrNiMo steel Gunbalanced other design
mechanical seal components
Shaft seal
Material type
CrNiMo steel G
Carbon graphite, anitmony impregnated
ASliding ring
Mechanical seal permissible permissible Hot water Thermal oil
Bearing type internal pump suction ➀ ➁
pressure pressure
NTWH U3.3A - K1NBWHNIWH
CTWH U3.3A - K1CBWHCIWH
p ≤ 22 bar
Series
Einsatzgrenzen
t ≤ + 207 °C
t ≤ + 183 °Ct = -30°C bis
+ 350 °C
U2.11A - S1
U2.11A - S1
p ≤ 16 barp ≤ 12 bar
p ≤ 25 bar
ALLHHEEAATT®
2
Pressure and temperature limits depending on housingmaterials
Materials
Abbreviation
NTWH 32 - 200 / 01 /180 U3.3A-K1 W128 - 38 / 300
Series
SizeNominal width of discharge nozzle
Nominal diameter of impeller
Hydraulic-No.
Actual diameter of impeller
Shaft seal
Bearing type
Material type
Bore diameter of plug-in shaft forattachment to end of motor shaft
External diameter of motor stool resp.flange size of electric motor➀ For series CIWH ACTUAL width of discharge nozzle
The abbreviation is displayed on the nameplate.
Bearing and lubrication
NTWH/CTWHPump side: Sliding bearing, lubricated by pumped mediumDrive side: Deep groove ball bearing, grease-lubricated
NBWH/CBWH/NIWH/CIWHPump side: Sliding bearing, lubricated by pumped fluidDrive side: Deep groove ball bearing of drive motor,
grease-lubricated
ConnectionsThe following connections are always provided:
FD1 DrainingFD2 DrainingFF2 / FV1 Filling / BleedingFF4 / FV4 Filling / Bleeding
(only for vertical block and in-line installation)LO1 Leakage outlet** According to DIN 4754 for non-hazardous draining of heat transfer medium
leaking from the shaft seal.
Component combinationsThe table on page 5 shows the possible combinations of componentsfor all ALLHEAT sizes.
Due to the modular design, spare parts management is simplified.
Dismantling of push-in unit NTWH/CTWHWhere a shaft coupling with a dismantling unit is used, the push-inunit can be removed towards the motor side, whilst the volute casingand the motor may remain on the base plate and the pipes connetedto the volute casing.
Dismantling of drive unit NBWH/CBWH/NIWH/CIWHDuring dismantling of the drive unit, the volute casing can remain inthe pipeline.
Shaft coupling and contact protectionElastic shaft coupling acc. to DIN 740 with or without disassemblysection. A coupling protection is supplied as a contact protection acc.to DIN 31001, where the scope of delivery includes a pump, baseplate and shaft coupling.
Option:Equipped with an elastic torsionally elastic cardanic coupling (baseplate must have been adapted).We recommend the use of double cardanic couplings under the follo-wing operating conditions:
$ In case of changing temperatures of the pumped medium$ In case of changing ambient temperatures or ventilation$ In case of plants that are sensitive to vibration
Series NTWH for sizes 65-315, 65-400, 80-315 and 100-315 with anominal impeller diameter of 315 and 400, a double cardanic couplingat t ≥ 207°C is supplied as standard.
Denomination PartNo. NTWH CTWH
NBWH CBWHNIWH CIWH
W128 W110
Volute casing 102.01 EN-GJS-400-15 EN-GJS-400-18LT(GGG-40) (GGG-40.3)
Impeller 230.01Casing cover 161.01Shaft 210.01Plug-in shaft 220.01Bearing bracket 330.01Motor stool 341.01Intermediate ring 509.01 EN-GJS-400-15 EN-GJS-400-18LT
(GGG-40) (GGG-40.3)
Bearing sleeve-S1 529.01Bearing bush-S1 545.01Bearing bush-K1 545.01
1.4021 / 1.7139
Material type
Series
EN-GJL-200 (GG-20)EN-GJS-400-18LT (GGG-40.3)
1.4021
SSiCSSiC
Kohle / 1.7139
EN-GJS-400-18LT (GGG-40.3)EN-GJL-250 (GG-25)
18
14
12
16
-30 100
20
300
22
24
26
400
10
0
EN-GJS-400-15 (GGG-40)
EN-GJS-400-18LT (GGG-40.3)
NTWH / NBWH / NIWH
8
25 CTWH / CBWH / CIWH
p bar
350200t ° C
Steam pressure curve - water
only for seriesNBWH / NIWHCBWH / CIWH
➀
ALLHHEEAATT®
3
Base plate series NTWH/CTWHWarp-resistant base plate made from steel, U section steel or castiron including collecting channel (see separate installation plans).
For couplings with / without dismantling unit:
Installation plan VM 854 D/GB/F/...U section steel Cast-iron plates
without with without with
Dog coupling 3100 -... 3200 -... 3300 -... 3400 -...double cardanic 3500 -... 3600 -... 3700 -... 3800 -...coupling
DriveSurface-cooled IEC three-phase cage motors; model IM B3, protec-tion type IP 55, insulation class F, performances and main dimensionsacc. to DIN 42 673.
Attention: Motors provided by the client must be able to generate acooling airflow in axial direction to the pump side that unimpededlycontacts the pump surface. It must also be ensured that any heat canbe freely dissipated into the atmosphere.
Block and in-line pumps of series NBWH, CBWH, NIWH, CIWHDriven by surface-cooled IEC three-phase cage motors with axialthrust bearing, model IM V1, protection type IP55, insulation class F,performances and main dimensions acc. to DIN 42 677.
Attention: Motors provided by the client must contain a axial thrustbearing on the drive side for block or in-line pumps.
ALLHHEEAATT®
Sectional drawing - series NTWH / CTWH
4cm
4cm
Maintenance-friendlydesign, easy to dis-mantle, pump housingcan remain in pipework
Low axial thrust on shaftbearing as a result ofhydraulically-balancedimpellers
Impellers with optimisedhydraulics and excellentefficiency
Pressure-containing casingparts in nodular cast ironfor high operationalreliability
Solid sliding bearing, lubricatedwith pumped medium,due to low temperature level,no evaporation of pumpingmedium,offering a high carrying force andlong life,available in SSiC/SSiC orcarbon/ steel
Optimum temperaturereduction, due to long coo-ling-off section and largesurface area of the sealingspace, no additional coo-ling is required
Large sealing area speci-al design to prevent therotation of gas bubblesand partial dry running ofthe mechanical seal
Optimised modularsystem as a result ofusing identical parts forthe process, block andin-line models
Optimised rolling bearingoffering exceptional ope-rational reliability andlong life
Balanced or unbalanced,maintenance-free stan-dard mechaincal seal withchambered O-ring,no additional cooling
High mechanical stabilityand strength due tooptimum stiffening ribsarrangement
Added operationalreliability due to safetystuffing box followed by athrottle and cooling section
Rigid, robust pump shaft
Wear-resistant casingdesign
4
Thermal isolation ofvolute casing is allowedup to this line
ALLHHEEAATT®
5
Interchangability of componentsParts with the same number are interchangeable within a vertical column.
Bearing Im- Inter- Casing Bearing Shaft Bearing Bearing Plug- Motor
bracket peller mediate cover bracket sleeve bush in stoolsize ring shaft
NTWH
NTWH NBWH NIWH NBWH NIWH NTWH NBWH
25-160/11 $ $ - 1 - 1 1 1
25-200/01 $ $ $ 2 1 2 2 2
32-160/01 $ $ $ 3 2 3 1 1
32-200/01 $ $ $ 4 3 4 2 2
40-160/01 $ $ $ 5 4 5 1 1
40-200/01 $ $ $ 6 5 6 2 2
40-250/01 $ $ $ 7 6 7 1 3 3
50-160/01 $ $ $ 8 7 8 2 2
50-200/01 $ $ $ 9 8 9 2 2
50-250/01 $ $ $ 10 9 10 1 3 3
65-160/01 $ $ $ 11 10 11 - 2 2
65-200/02 $ $ $ 12 12 12 1 3 3
80-160/01 $ $ $ 13 12 13 3 3
100-160/01 $ $ - 14 - 14 4 4
65-250/01 $ 15 - 15 - 5
65-315/01 $ 16 - 16 2 6
65-400/01 $ 17 - 17 3 7
80-200/02 $ 18 - 18 8
80-250/01 $ 19 - 19 5
80-315/01 $ 20 - 20 2 7
100-200/01 $ 21 - 21 5
100-250/01 $ 22 - 22 6
100-315/01 $ 23 - 23 2 7
125-200/01 $ 24 - 24 7
125-250/01 $ 25 - 25 7
150-200/01 $ 26 - 26 8
Bearing Im- Inter- Casing Bearing Shaft Bearing Bearing Plug- Motor
bracket peller mediate cover bracket sleeve bush in stoolsize ring shaft
CTWH
CTWH CBWH CIWH CBWH CIWH CTWH CBWH
25-160/11 $ $ - 27 - 1 1 1
25-200/01 $ $ 32-200/11 28 13 2 2 2
32-160/11 $ $ 40-160/11 29 14 3 1 1
32-200/11 $ $ 40-200/11 30 15 4 2 2
40-160/11 $ $ 50-160/11 31 16 5 1 1
40-200/11 $ $ 50-200/11 32 17 6 2 2
50-160/11 $ $ 65-160/11 33 18 8 2 2
50-200/11 $ $ 65-200/11 34 19 9 2 2
65-160/11 $ $ - 35 - 27 2 2
80-160/11 $ $ - 36 - 28 3 3
32-250/11 $ 37 29 8
40-250/11 $ 38 30 8
40-315/11 $ 39 31 4 5
50-250/11 $ 40 32 - 8
50-315/11 $ 41 33 4 6
65-200/11 $ 42 34 8
65-250/11 $ 43 15 5
80-200/11 $ 44 35 8
80-250/11 $ 45 19 6
100-200/11 $ 46 21 5
foot
foot
Assignment to sizes depends on the
speed, motor output and motor model
2 2
Supporting
2
2
1 1
2 2 - -
200 250 300 350 400
19 24 28 38 42 48 55
-
Pump Volute
casing
Volute
--
Pump Series
Series
size
--
2
-
-
-
-
-
1
-
1 1
casing
2
1 1
2 2
-
-
1 1
-
2 2
-
size
Assignment to sizes depends on the
speed, motor output and motor model
-
Supporting
1 1 1
19 24 28 38 42 48 55
200 250 300 350 400
- -
ALLHHEEAATT®
6
Performance graphsSeries NTWH
For exact performance data please refer to the individual characteristics.
NTWH
NTWH
NTWH
CTWH
CTWH
NTWH
Series CTWH
CTWH
CTWH
ALLHHEEAATT®
7
For exact performance data please refer to the individual characteristics.
Performance graphsSeries NBWH
NBWH
NBWH
NBWH
CBWH
CBWH
NBWH
Series CBWH
CBWH
CBWH
ALLHHEEAATT®
8
For exact performance data please refer to the individual characteristics.
Performance graphsSeries NIWH
NIWH
NIWH
NIWH
CIWH
CIWH
NIWH
Series CIWH
CIWH
CIWH
ALLHHEEAATT®
9VM 854 GB/11.01 1000 - Ident-No. 796 219
Sectional drawing - Series NTWH / CTWH on bearing bracket size 1 and 2Design U2.11A-S1 (balanced mechanical seal and SiC-bearing)
Denomination Part No.
Volute casing 102.01Casing cover 161.01Supporting foot 183.01Shaft 210.01Impeller 230.01Groove ball bearing 321.02Bearing bracket 330.01Bearing cover 360.02Gasket 400.01Gasket 400.02Gasket 400.03Seal ring 411.02Seal ring 411.06Seal ring 411.07Seal ring 411.08Mechanical seal 433.01Stuffing box packing 461.01Intermediate ring 509.01Centering ring ➀ 511.01Centering ring ➀ 511.02Flexible clamp ring 517.01Flexible clamp ring ➀ 517.02Bearing sleeve ➀ 529.01Bearing bush 545.01
Denomination Part No.
Disc ➀ 550.01Disc ➀ 550.02Disc spacer 551.01Disc spacer 551.02Disc spacer 551.04Disc spacer 551.05Disc spacer ➀ 551.06Disc spacer ➀ 551.07Rivet 565.01Pipe 710.01Hexagon screw 901.01Hexagon screw 901.02Hexagon screw 901.06Hexagon screw 901.13Stud bolt ➁ 902.01Stud bolt ➁ 902.02Screw plug 903.02Screw plug 903.06Screw plug 903.07Screw plug 903.08Socket-head cap screw 914.08Nut ➁ 920.01Nut ➁ 920.02Impeller nut 922.01
Denomination Part No.
Bearing nut ➀ 923.01Circlip 932.01Circlip 932.02Circlip 932.03Circlip 932.05Circlip ➀ 932.06Spring ring 936.01Key 940.01Key 940.02Name plate 971.01
➀ not present for desing with carbon bearing➁ only with series CTWH
Connections
FD1 DrainingFD2 DrainingFF2 / FV1 Filling / BleedingFF4 / FV4 Filling / Bleeding
only for vertical block and in-lineinstallations
LO1 Leakage outlet
902.01920.01
971.01
710.01
210.01321.02411.06433.01551.02551.07529.01545.01551.05551.04903.06400.03923.01932.03517.01 565.01
914.08901.06
550.01 550.02 932.02 411.08 183.01 360.02 940.02
932.05901.13330.01903.08511.02
551.06
517.02511.01932.06
901.01 411.07 903.07
102.01
400.01
161.01
230.01
551.01
936.01
922.01
940.01
932.01
461.01
903.02
411.02
210.01545.01 433.01
509.01 901.01901.02400.01 400.02
902.02920.02
902.01920.01
Design U3.3A-K1(unbalanced mechanical seal and carbon bearing)
Design with intermediate ring
ALLHHEEAATT®
10VM 854 GB/11.01 1001 - Ident-No. 796 219
Sectional drawing - Series NBWH / CBWHDesign U2.11A-S1 (balanced mechanical seal and SiC-bearing)
Denomination Part-No.
Volute casing 102.01Casing cover 161.01Supporting foot 183.01Plug-in shaft 220.01Impeller 230.01Bearing bracket 330.01Motor stool 341.01Gasket 400.01Gasket 400.02Gasket 400.03Seal ring 411.02Seal ring 411.06Seal ring 411.07Seal ring 411.08O-ring ➀ 412.07Mechanical seal 433.01Stuffing box packing 461.01Intermediate ring 509.01Centering ring ➀ 511.01Centering ring ➀ 511.02Flexible clamp ring 517.01Flexible clamp ring ➀ 517.02Shaft sleeve ➀ 524.01Bearing sleeve ➀ 529.01Bearing bush 545.01
Denomination Part-No.
Disc ➀ 550.01Disc ➀ 550.02Disc spacer 551.01Disc spacer ➁ 551.02Disc spacer ➀ 551.06Disc spacer ➀ 551.07Washer 554.08Washer 554.13Rivet 565.01Guard plate 686.01Guard plate 686.02Pipe 710.01Flange motor 801.01Fan 831.01Hexagon screw 901.01Hexagon screw 901.02Hexagon screw 901.06Hexagon screw 901.07Hexagon screw 901.08Hexagon screw 901.10Hexagon screw 901.13Screw plug 903.02Screw plug 903.06Screw plug 903.07Screw plug 903.08
Denomination Part-No.
Socket-head cap screw 914.06Nut 920.13Impeller nut 922.01Bearing nut ➀ 923.01Circlip 932.01Circlip ➁ 932.02Circlip 932.03Circlip ➀ 932.06Spring ring 936.01Key 940.01Name plate 971.01
➀ not present for design with carbon bearing➁ not present for design with SiC-bearing
903.02
903.08
801.01901.10330.01903.06923.01511.02517.01545.01 400.03 524.01 411.06 831.01 341.01
412.07 554.13 901.13 914.06551.07550.02550.01932.06551.06 517.02 932.03 411.08 433.01 920.13 183.01 220.01
529.01565.01 511.01
971.01
411.02
461.01
932.01
940.01
922.01
936.01
161.01
230.01
551.01
102.01
400.01
220.01433.01551.02932.02545.01
710.01
686.01554.08901.08901.01901.07686.02901.06
400.01400.02
509.01901.02
901.01 411.07 903.07
Design U3.3A-K1(unbalanced mechanicalseal and carbon bearing
Design withintermediate ring
Connections
FD1 DrainingFD2 DrainingFF2 / FV1 Filling / BleedingFF4 / FV4 Filling / Bleeding
only for vertical installationsLO1 Leakage outlet
ALLHHEEAATT®
11VM 854 GB/11.01 1002 - Ident-No. 796 219
Sectional drawing - Series NIWH / CIWHDesign U2.11A-S1 (balanced mechanical seal and SiC-bearing)
710.01
903.07
433.01
411.08
903.08
400.03
932.03
914.06
330.01
411.06
903.06
412.07
524.01
517.01
551.07
511.02
565.01
550.02
971.01
400.01 551.01 936.01 940.01 461.01 411.02
161.01903.02932.01922.01102.01230.01
529.01
901.10
801.01
220.01
831.01
341.01
923.01
517.02
545.01
550.01
511.01
551.06
932.06
901.08
554.08
686.02
901.06
686.01
901.07
901.01
411.07
220.01
545.01
433.01
932.02
551.02
902.01920.01
Denomination Part-No.
Volute casing 102.01Casing cover 161.01Plug-in shaft 220.01Impeller 230.01Bearing bracket 330.01Motor stool 341.01Gasket 400.01Gasket 400.02Gasket 400.03Seal ring 411.02Seal ring 411.06Seal ring 411.07Seal ring 411.08O-ring ➀ 412.07Mechanical seal 433.01Stuffing box packing 461.01Intermediate ring 509.01Centering ring ➀ 511.01Centering ring ➀ 511.02Flexible clamp ring 517.01Flexible clamp ring ➀ 517.02Shaft sleeve ➀ 524.01Bearing sleeve ➀ 529.01Bearing bush 545.01
Denomination Part-No.
Disc ➀ 550.01Disc ➀ 550.02Disc spacer 551.01Disc spacer ➁ 551.02Disc spacer ➀ 551.06Disc spacer ➀ 551.07Washer 554.08Rivet 565.01Guard plate 686.01Guard plate 686.02Pipe 710.01Flange motor 801.01Fan 831.01Hexagon screw 901.01Hexagon screw 901.02Hexagon screw 901.06Hexagon screw 901.07Hexagon screw 901.08Hexagon screw 901.10Screw plug 903.02Screw plug 903.06Screw plug 903.07Screw plug 903.08Socket-head cap screw 914.06
Denomination Part-No.
Impeller nut 922.01Bearing nut ➀ 923.01Circlip 932.01Circlip ➁ 932.02Circlip 932.03Circlip ➀ 932.06Spring ring 936.01Key 940.01Name plate 971.01
➀ not present for design with carbon bearing➁ not present for design with SiC-bearing
Connections
FD1 DrainingFD2 DrainingFF2 / FV1 Filling / BleedingFF4 / FV4 Filling / Bleeding
only for vertical installationsLO1 Leakage outlet
Design U3.3A-K1(unbalanced mechanicalseal and carbon bearing)
Design withintermediate ring
400.01
400.02
509.01
901.02
901.01
ALLHHEEAATT®
VM 854 GB/11.01 2000 - Ident-No. 796 219 12
Pump dimension - Series NTWH / CTWHSizes on bearing bracket sizes 1 and 2
Key acc. toDIN 6885
bfbf
s2
t
d1
um3
n4n3
n1
n2
s1b
c
h2
b1
w
m1
m2
DNd
e
c1
l
x
fa
DN
s
h1
b2
Arrangement
Arrangement Arrangement4 holes
8 holes
12 holes
k
g
D
DN
dD
Ns
No. ofholes
25 115 16 85 14 432 140 18 100 19 440 150 18 110 19 450 165 20 125 19 465 185 20 145 19 480 200 22 160 19 8100 220 24 180 19 8125 250 26 210 19 8150 285 26 240 23 8200 340 30 295 23 12
Flanges acc. to EN 1092-2 PN 16
DNs/DNd D bf k gTolerances of companion dimensionsaccording to DIN EN 735
Sence of rotation: clockwise, as seen from the driving side
Dimensions in mmSubject to alteration
No. ofholes
25 115 18 85 14 432 140 20 100 19 440 150 20 110 19 450 165 22 125 19 465 185 24 145 19 880 200 26 160 19 8100 235 28 190 23 8125 270 30 220 28 8
Flanges acc. to EN 1092-2 PN 25
DNs/DNd D bf k g
Series NTWH
Series CTWH
ALLHHEEAATT®
VM 854 GB/11.01 2001 - Ident-No. 796 219
Bearing Pump Suction Deliverybracket size flange flangesize
DNs DNd a f b1 b2 h1 h2 b c c1 e m1 m2 m3 n1 n2 n3 n4 w s1 s2 x d1 l t u 25-160/11 40 25 80 360 128 128 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 80 24 50 27 8 25-200/01 40 25 80 360 132 132 160 180 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 80 24 50 27 8 32-160/01 50 32 80 360 130 130 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 80 24 50 27 8 32-200/01 50 32 80 360 124 130 160 180 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 80 24 50 27 8 40-160/01 65 40 80 360 130 130 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 80 24 50 27 8 40-200/01 65 40 100 360 125 135 160 180 50 15 4 28 100 70 45 265 212 160 110 260 M 12 M 12 80 24 50 27 8 40-250/01 65 40 100 360 150 156 180 225 65 15 4 28 125 95 45 320 250 160 110 260 M 12 M 12 80 24 50 27 8 50-160/01 65 50 100 360 125 130 160 180 50 15 4 28 100 70 45 265 212 160 110 260 M 12 M 12 80 24 50 27 8 50-200/01 65 50 100 360 133 145 160 200 50 15 4 28 100 70 45 265 212 160 110 260 M 12 M 12 80 24 50 27 8 50-250/01 65 50 100 360 156 169 180 225 65 15 4 28 125 95 45 320 250 160 110 260 M 12 M 12 80 24 50 27 8 65-160/01 80 65 100 360 133 162 160 200 65 15 4 28 125 95 45 280 212 160 110 260 M 12 M 12 80 24 50 27 8 65-200/02 80 65 100 360 150 170 180 225 65 15 4 28 125 95 45 320 250 160 110 260 M 12 M 12 100 24 50 27 8 80-160/01 100 80 125 360 136 170 180 225 65 15 4 28 125 95 45 320 250 160 110 260 M 12 M 12 100 24 50 27 8 100-160/01 125 100 125 360 165 200 200 280 65 15 4 28 125 95 45 320 250 160 110 260 M 12 M 12 100 24 50 27 8 65-250/01 80 65 100 470 164 184 200 250 80 18 4 28 160 120 45 360 280 160 110 340 M 16 M 12 100 32 80 35 10 65-315/01 80 65 125 470 202 219 225 280 80 25 6 30 160 120 47 400 315 160 110 340 M 16 M 12 100 32 80 35 10 65-400/01 80 65 125 470 239 255 250 355 80 25 6 30 160 120 47 420 335 160 110 340 M 16 M 12 100 32 80 35 10 80-200/02 100 80 125 470 172 190 180 250 65 18 4 28 125 95 45 345 280 160 110 340 M 16 M 12 100 32 80 35 10 80-250/01 100 80 125 470 182 208 200 280 80 18 4 28 160 120 45 400 315 160 110 340 M 16 M 12 100 32 80 35 10 80-315/01 100 80 125 470 210 231 250 315 80 25 6 30 160 120 47 400 315 160 110 340 M 16 M 12 100 32 80 35 10 100-200/01 125 100 125 470 165 203 200 280 80 18 4 28 160 120 45 360 280 160 110 340 M 16 M 12 120 32 80 35 10 100-250/01 125 100 140 470 189 224 225 280 80 18 6 30 160 120 47 400 315 160 110 340 M 16 M 12 120 32 80 35 10 100-315/01 125 100 140 470 220 250 250 315 80 25 6 30 160 120 47 400 315 160 110 340 M 16 M 12 120 32 80 35 10 125-200/01 150 125 140 470 196 236 250 315 80 18 6 30 160 120 47 400 315 160 110 340 M 16 M 12 120 32 80 35 10 125-250/01 150 125 140 470 212 255 250 355 80 18 6 30 160 120 47 400 315 160 110 340 M 16 M 12 120 32 80 35 10 150-200/01 200 150 160 470 214 268 280 370 100 27 6 30 200 150 47 550 450 160 110 340 M 20 M 12 120 32 80 35 10
Pump dimensions
2
1
Shaft endfor
Exten-sion dim.
Foot dimenensions
screwacc. to DIN 748
LO1 FV4FF4
FV1FF2
FD2FD1
Bearingbracket Leakagesize outlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
1
2
Connections
G 1/4
Draining Filling/Bleeding
G 1/4
G 1/4G 1/4
G 1/2G 3/8
G 1/4 only for
vertical block and in-lineinstallation
Connection FD1 in size 25-160/11 and 25-200/01 each G 1/2
Arrangement of connections - Series NTWH
Dimensions in mmSubject to alteration
13
ALLHHEEAATT®
VM 854 GB/11.01 2002 - Ident-No. 796 219
Bearing Pump Suction Druck-bracket size flange flanschsize
DNs DNd a f b1 b2 h1 h2 b c c1 e m1 m2 m3 n1 n2 n3 n4 w s1 s2 x d1 l t u 25-160/11 40 25 80 360 128 128 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 100 24 50 27 8 25-200/01 40 25 80 360 132 132 160 180 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 100 24 50 27 8 32-160/11 50 32 80 360 130 130 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 100 24 50 27 8 32-200/11 50 32 80 360 130 135 160 180 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 100 24 50 27 8 40-160/11 65 40 80 360 130 130 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M 12 M 12 100 24 50 27 8 40-200/11 65 40 100 360 130 140 160 180 50 15 4 28 100 70 45 265 212 160 110 260 M 12 M 12 100 24 50 27 8 50-160/11 80 50 100 360 130 130 160 180 50 15 4 28 100 70 45 265 212 160 110 260 M 12 M 12 100 24 50 27 8 50-200/11 80 50 100 360 135 150 160 200 50 15 4 28 100 70 45 265 212 160 110 260 M 12 M 12 100 24 50 27 8 65-160/11 100 65 100 360 130 155 160 200 65 15 4 28 125 95 45 280 212 160 110 260 M 12 M 12 100 24 50 27 8 80-160/11 125 80 125 360 145 180 180 225 65 15 4 28 125 95 45 320 250 160 110 260 M 12 M 12 140 24 50 27 8 32-250/11 50 32 100 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M 12 M 12 100 32 80 35 10 40-250/11 65 40 100 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M 12 M 12 100 32 80 35 10 40-315/11 65 40 125 470 200 200 200 250 65 20 4 28 125 95 45 345 280 160 110 340 M 12 M 12 100 32 80 35 10 50-250/11 80 50 125 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M 12 M 12 100 32 80 35 10 50-315/11 80 50 125 470 200 200 225 280 65 20 6 30 125 95 47 345 280 160 110 340 M 12 M 12 100 32 80 35 10 65-200/11 100 65 100 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M 12 M 12 140 32 80 35 10 65-250/11 100 65 125 470 170 190 200 250 80 18 4 28 160 120 45 360 280 160 110 340 M 16 M 12 140 32 80 35 10 80-200/11 125 80 125 470 170 190 180 250 65 18 4 28 125 95 45 345 280 160 110 340 M 12 M 12 140 32 80 35 10 80-250/11 125 80 125 470 185 210 225 280 80 18 6 30 160 120 47 400 315 160 110 340 M 16 M 12 140 32 80 35 10 100-200/11 125 100 125 470 170 205 200 280 80 18 4 28 160 120 45 360 280 160 110 340 M 16 M 12 140 32 80 35 10
2
1
Pump dimensions Shaft endfor
Exten-sion dim.
Foot dimensions
screw
LO1 FV4FF4
FV1FF2
FD2FD1
Bearingbracket Leakagesize outlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
1
2
G 1/2
G 1/4 only for
vertical block and in-line installation
Connections
G 1/4
Draining Filling/Bleeding
G 1/4
G 1/2
G 1/4
Arrangement of connections - Series CTWH
Dimensions in mmSubject to alteration
14
ALLHHEEAATT®
15
ALLHHEEAATT®
Unit dimensions - Series NBWH / CBWHSizes with a shaft diameter of 32 at the shaft seal
DNd
DN
s
for
M12
110
bfbf
4
c
45
27
h3
s1
for screws
h3
n1
n2
b
b1 b2
x
l1
l
f
340
m1
m2
a
h1h2
d
a1
160
45°
Arrangementof terminal boxonly for motorsize 200L
VM 854 GB/11.01 3000 - Ident-No. 796 219 16
No. ofholes
25 115 16 85 14 432 140 18 100 19 440 150 18 110 19 450 165 20 125 19 465 185 20 145 19 480 200 22 160 19 8100 220 24 180 19 8125 250 26 210 19 8
Flanges acc. to EN 1092-2 PN 16
DNs/DNd D bf k g
Leakageoutlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
G 1/4G 1/4 G 1/4
Connections
G 1/4
Draining Filling/Bleeding
G 1/4 only for vertical
installation
FD1
LO1
FD2
FF2FV1
FF4FV4
FD1FD2
LO1
FF2FV1
Connections for horizontal and vertical installation
Connection FD1 in size 25-160/11 and 25-200/01 each G 1/2
Tolerances of companion dimensionsaccording to DIN EN 735
Sence of rotation: clockwise, as seen fromthe driving side
Dimensions in mmSubject to alteration
DN
sD
Nd
D
g
Arrangement8 holes
Arragement4 holes
k
Series NBWH
No. ofholes
25 115 18 85 14 432 140 20 100 19 440 150 20 110 19 450 165 22 125 19 465 185 24 145 19 880 200 26 160 19 8100 235 28 190 23 8125 270 30 220 28 8
Flanges acc. to EN 1092-2 PN 25
DNs/DNd D bf k g
Leakageoutlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
G 1/4G 1/2 G 1/4
Connections
G 1/4
Draining Filling/Bleeding
G 1/4 only for vertical
installation
Series CBWH
a1
d
h1
a1
d
h1
ALLHHEEAATT®
n = 1450 / 1750 1/min
VM 854 GB/11.01 3001 - Ident-No. 796 219 17
Unit dimensions - Series NBWH
marking in table $ marking in table X
d2 2
h1 > ora1 a1 d2 2
h1 < orBase plate and/or foundation design
Pump Motorsize size Exten-
siondim.
DNs DNd a f b1 b2 h1 h2 b c m1 m2 n1 n2 s1 a1 d h3 l1 l x
25-160/11 80 $ 0,55 0,75 40 25 80 371 128 128 132 160 50 15 100 70 240 190 M 12 200 162 124 234 685 102 19/20080 $ 0,55 0,75 162 124 234 685 19/200
90 S $ 181 130 282 733 24/20080 $ 0,55 0,75 162 124 234 685 19/200
90 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 2,2 3 250 203 158 312 763 28/250
80 $ 0,55 0,75 162 124 234 685 19/20090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 2,2 3 250 203 158 312 763 28/250
80 $ 0,55 0,75 162 124 234 685 19/20090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 2,2 3 250 203 158 312 763 28/250
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 250 203 158 312 783 28/25090 S $ 181 130 282 705 24/20090 L $ 181 130 282 705 24/200100 L $ 2,2 3 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 412 300 266 196 375 887 38/300
Base
plat
e an
d/or
fo
unda
tion
desig
n se
e ab
ove
Flanges Feet
Assignment plug-in shaft/ motor stool
Motor dimensionsApproximate dimensions
different depending upon manufacturer
Pump
Performance Unit dimensions
kW
102
200
200
200
M 12
19050180
123
M 12
250
102
102
85
102
250
190
200
200
212 M 12
M 12
100
M 12
70
70
70
265
240
240
32095
50
50
100
10015
125
371
371
125
160
160
132
135
124 160
123
150 156
15130
15
15
225 65
180371100
371
80
100
80
40
32
4065
1,1
1,1
1,1
1,1
1,5
1,5
180
1,1
40
25-200/01 40 1323718025
371
102200M 12190240701001550180160132
123 123 19024070100155016013232-160/01 32 80
4
40-160/01
50
40-250/01 65
65
5032-200/01
40-200/011,1
5,5
1,5
1,5
1,5
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
Dimensions in mmSubject to alteration
ALLHHEEAATT®
n = 1450 / 1750 1/min
VM 854 GB/11.01 3002 - Ident-No. 796 219 18
Unit dimensions - Series NBWH
Pump Motorsize size Exten-
siondim.
DNs DNd a f b1 b2 h1 h2 b c m1 m2 n1 n2 s1 a1 d h3 l1 l x
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 250 203 158 312 783 28/250
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 412 300 266 196 375 887 38/30090 L $ 200 181 130 282 753 24/200100 L $ 2,2 3 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 266 196 375 887 38/300132 M $ 266 196 375 887 38/300
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 203 158 312 783 28/250112 M $ 228 171 335 806 28/25090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 250 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 266 196 375 887 38/300132 M $ 266 196 375 887 38/30090 S $ 181 130 282 778 24/20090 L $ 181 130 282 778 24/200100 L $ 2,2 3 203 158 312 808 28/250112 M $ 228 171 335 831 28/250132 S $ 412 300 266 196 375 912 38/30090 L $ 200 181 130 282 778 24/200100 L $ 2,2 3 203 158 312 808 28/250112 M $ 228 171 335 831 28/250132 S $ 266 196 375 912 38/300132 M $ 266 196 375 912 38/300
Assignment plug-in shaft/ motor stool
Motor dimensionsApproximate dimensions
different depending upon manufacturer
Unit dimensions
Flanges
37150
100 15
15169
133 145 160
Base
plat
e an
d/or
fo
unda
tion
desig
n se
e ab
ove
page
17
Feet
Pump
Performance
300
102
300
kW
200
4
100
85
102
250
102250200 280 65 15 125 95 320250
M 12
M 12
65
9565 15 125
25095
412
165 2004371
1,5
200
25032095
95 280 212
M 12
M 12
300
250102320 250
200
M 12
125
15 125
12515
250
150
156
133
320
65
65
225
170 180
180 225136 170
162 200
225
180
160
371
371
412
371
412
100
125
125
100
80
100
7,55,5
80
5,5
5,5
100
125
7,5
65
65
80
4
1,5
4
65
5,57,5
1,5
1,51,1
1,1
65-200/02
80-160/014
1,11,5
50-160/01 65 50
50-200/01 65 50
100-160/01
50-250/01
65-160/01
100371 125 130 160
100371
200102
1,11,5
70 265 212 M 12180 50
M 12200 50 15 100
200
102
1,11,5
2504
5,5
70 265 212
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
Dimensions in mmSubject to alteration
ALLHHEEAATT®
Unit dimensions - Series NBWH / CBWHSizes with a shaft diameter of 32 at the shaft seal
DNd
DN
s
for
M12
110
bfbf
4
c
45
27
h3
s1
for screws
h3
n1
n2
b
b1 b2
x
l1
l
f
340
m1
m2
a
h1h2
d
a1
160
45°
Arrangementof terminal boxonly for motorsize 200L
VM 854 GB/11.01 3000 - Ident-No. 796 219 19
No. ofholes
25 115 16 85 14 432 140 18 100 19 440 150 18 110 19 450 165 20 125 19 465 185 20 145 19 480 200 22 160 19 8100 220 24 180 19 8125 250 26 210 19 8
Flanges acc. to EN 1092-2 PN 16
DNs/DNd D bf k g
Leakageoutlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
G 1/4G 1/4 G 1/4
Connections
G 1/4
Draining Filling/Bleeding
G 1/4 only for vertical
installation
FD1
LO1
FD2
FF2FV1
FF4FV4
FD1FD2
LO1
FF2FV1
Connections for horizontal and vertical installation
Connection FD1 in size 25-160/11 and 25-200/01 each G 1/2
Tolerances of companion dimensionsaccording to DIN EN 735
Sence of rotation: clockwise, as seen from the driving side
Dimensions in mmSubject to alteration
DN
sD
Nd
D
g
Arrangement8 holes
Arragement4 holes
k
Series NBWH
No. ofholes
25 115 18 85 14 432 140 20 100 19 440 150 20 110 19 450 165 22 125 19 465 185 24 145 19 880 200 26 160 19 8100 235 28 190 23 8125 270 30 220 28 8
Flanges acc. to EN 1092-2 PN 25
DNs/DNd D bf k g
Leakageoutlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
G 1/4G 1/2 G 1/4
Connections
G 1/4
Draining Filling/Bleeding
G 1/4 only for vertical
installation
Series CBWH
ALLHHEEAATT®
a1
d
h1
a1
d
h1
n = 2900 / 3500 1/min
VM 854 GB/11.01 3003 - Ident-No. 796 219 20
Unit dimensions - Series NBWH
marking in tabele $ marking in table X
d2 2
h1 > ora1 a1 d2 2
h1 < orBase plate and/or foundation design
Pump Motorsize size Exten-
siondim.
DNs DNd a f b1 b2 h1 h2 b c m1 m2 n1 n2 s1 a1 d h3 l1 l x
80 $ 0,75 1,1 162 124 234 685 19/20090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/25090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/250132 S $ 5,5 7,5 412 300 266 196 375 867 38/30090 L $ 200 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/250132 S X 5,5 7,5 300 266 196 375 867 38/300160 M X 11 15 350 320 234 481 973 42/350112 M $ 371 250 228 171 335 786 28/250132 S $ 5,5 7,5 300 266 196 375 867 38/300160 M X 11 15 320 234 481 973 42/350160 L X 320 234 481 973 42/35090 L $ 200 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/250132 S X 5,5 7,5 300 266 196 375 867 38/300160 M X 11 15 320 234 481 973 42/350160 L X 320 234 481 973 42/350112 M $ 371 250 228 171 335 806 28/250132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400
80
180 50
123 132123
371
50
25-200/01
250
100
100 70
24070100
13240 25 80
124412
8032
32371
412
1,5
6540-200/01
18,5
65
4
40-160/01
32-160/01
34
123
132 15
160 50 15
132123
15
160
50
412
8040 160
18,5
102250
250102
200
10040
2,2
2,2
22
18,5
160
2,2
4
3
3
4
4
1001550
70
1550 100 70
M 12
240
50180
190
190
240
102M 1226570 212350
180160135125412
Base
plat
e an
d/or
fo
unda
tion
desig
nse
e ab
ove
Pump
Performance Unit dimensionsMotor dimensions
Approximate dimensionsdifferent depending upon manufacturerFeetFlanges
kW
Assignment plug-in shaft/ motor stool
200
371
M 12
102
350
M 12190240
102350
M 1219013032-200/01
4
102
250
M 12190240701001550160132254025-160/11 128128371802,23
1,5
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
Dimensions in mmSubject to alteration
ALLHHEEAATT®
n = 2900 / 3500 1/min
VM 854 GB/11.01 3004 - Ident-No. 796 219 21
Unit dimensions - Series NBWH
Pump Motorsize size Exten-
siondim.
DNs DNd a f b1 b2 h1 h2 b c m1 m2 n1 n2 s1 a1 d h3 l1 l x
132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M $ 11 15 320 234 481 993 42/350160 L $ 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400100 L $ 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400160 M $ 11 15 320 234 481 993 42/350160 L $ 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400112 M $ 371 250 228 171 335 806 28/250132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M $ 11 15 320 234 481 993 42/350160 L $ 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400132 S $ 5,5 7,5 300 266 196 375 912 38/300160 M $ 11 15 320 234 481 1018 42/350160 L $ 320 234 481 1018 42/350180 M X 375 275 610 1147 48/350200 L X 30 37 400 415 310 665 1202 55/400132 S $ 5,5 7,5 300 266 196 375 912 38/300160 M $ 11 15 320 234 481 1018 42/350160 L $ 320 234 481 1018 42/350180 M $ 375 275 610 1147 48/350200 L X 30 37 400 415 310 665 1202 55/400
65225180 102350
350
15
320 250 M 12
25095
95 M 12212
102350
350 102
165 200 200412
65225
M 12280 65 15 125 95 320 250
412 156 169
412
170
100-160/01
350250 M 12
250
15
95
65 100 41265-200/02
80-160/01
15615065 40 100 412
50 100
40-250/0122
18,5
18,5
18,522
4
50-200/01
18,5
2218,5
22
22
18,5
18,5
22
4
22
125
80
65
100 80 125
125100
225
136
180
150
180170
160130125
15
180
95
225 65 15 125
1565200
15 125
50-250/01
50-160/01
125
125
1005065
3
M 12
320
320 250
M 12
70100
125 95
280
320
265
85
85
350102
102
350
M 12412
371
1550180
65
Base
plat
e an
d/or
fo
unda
tion
desig
nse
e ab
ove
page
20
Pump
Performance Unit dimensionsMotor dimensions
Approximate dimensionsdifferent depending upon manufacturerFeetFlanges
kW
Assignment plug-in shaft/ motor stool
160162133412
1006580
133
65-160/0118,5
102350M 12212502001601454121005065
21226570100
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
Dimensions in mmSubject to alteration
ALLHHEEAATT®
Unit dimensions - Series CBWH
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
d2 2
h1 > ora1 Base plate and/or foundation design a1 d2 2
h1 < ora1
d
h1
a1
d
h1
marking in table $ marking in table X
n = 1450 / 1750 1/minPump Motorsize size Exten-
siondim.
DNs DNd a f b1 b2 h1 h2 b c m1 m2 n1 n2 s1 a1 d h3 l1 l x
25-160/11 80 $ 0,55 0,75 40 25 80 371 128 128 132 160 50 15 100 70 240 190 M 12 200 162 124 234 685 102 19/20080 $ 0,55 0,75 162 124 234 685 19/200
90 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/20080 $ 0,55 0,75 162 124 234 685 19/200
90 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/20080 $ 0,55 0,75 162 124 234 685 19/200
90 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 2,2 3 250 203 158 312 763 28/250
80 $ 0,55 0,75 162 124 234 685 19/20090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 2,2 3 250 203 158 312 763 28/250
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 250 203 158 312 783 28/250
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 250 203 158 312 783 28/250
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 412 300 266 196 375 887 38/300
80 $ 0,55 0,75 162 124 234 705 19/20090 S $ 181 130 282 753 24/20090 L $ 181 130 282 753 24/200100 L $ 2,2 3 203 158 312 783 28/250112 M $ 228 171 335 806 28/25090 S $ 181 130 282 778 24/20090 L $ 181 130 282 778 24/200100 L $ 2,2 3 203 158 312 808 28/250112 M $ 228 171 335 831 28/250132 S $ 412 300 266 196 375 912 38/300
4025-200/01
10270 240 190 M 12160 50 15 100371 130 130 13232-160/11 50 32 80
M 12
200
1021,5
2504
5,5
125 95 320 250180 225 65 15125371
145 18080-160/11
1,1
125 80
200102
1,11,5
2504
95 280 212 M 12200 65 15 125371 130 155 16065-160/11 100 65 100
200
102
1,11,5
2504
5,5
70 265 212 M 12200 50 15 100371
135 150 16050-200/11 80 50 100
200102
1,11,5
70 265 212 M 12180 50 15 100371 130 130 16050-160/11 80 50 100
32-200/11
40-200/111,1
1,5
1,5
40-160/11
80
40
32
130
130
50180160132 2407010015 102200M 121901323718025
65
1,1
1,1
1,1
1,1
1,5
1,5
65
50
1,5
50
40 371100
80 371
160 15135
130
160
160
132
140 180 50 100
10015
100
15 70
70
70
265
240
240 102
102
102
190
200212 M 12
M 12
kW
200
200
20019050180
130
M 12371
Base
plat
e an
d/or
fo
unda
tion
desig
nse
e ab
ove
Flanges Feet
Assignment plug-in shaft/ motor stool
Motor dimensionsApproximate dimensions
different depending upon manufacturer
Pump
Performance Unit dimensions
Dimensions in mmSubject to alteration
VM 854 GB/11.01 3005 - Ident-No. 796 219 22
ALLHHEEAATT®
Unit dimensions - Series CBWH
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
n = 2900 / 3500 1/min
Pump Motorsize size Exten-
siondim.
DNs DNd a f b1 b2 h1 h2 b c m1 m2 n1 n2 s1 a1 d h3 l1 l x
80 $ 0,75 1,1 162 124 234 685 19/20090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/25090 S $ 181 130 282 733 24/20090 L $ 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/250132 S $ 5,5 7,5 412 300 266 196 375 867 38/30090 L $ 200 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/250132 S X 5,5 7,5 412 300 266 196 375 867 38/300112 M $ 371 250 228 171 335 786 28/250132 S $ 5,5 7,5 300 266 196 375 867 38/300160 M X 11 15 350 320 234 481 973 42/35090 L $ 200 181 130 282 733 24/200100 L $ 203 158 312 763 28/250112 M $ 228 171 335 786 28/250132 S X 5,5 7,5 300 266 196 375 867 38/300160 M X 11 15 350 320 234 481 973 42/350112 M $ 371 250 228 171 335 806 28/250132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350100 L $ 203 158 312 783 28/250112 M $ 228 171 335 806 28/250132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400112 M $ 371 250 228 171 335 806 28/250132 S $ 5,5 7,5 300 266 196 375 887 38/300160 M X 11 15 320 234 481 993 42/350160 L X 320 234 481 993 42/350180 M X 375 275 610 1122 48/350200 L X 30 37 400 415 310 665 1177 55/400132 S $ 5,5 7,5 300 266 196 375 912 38/300160 M $ 11 15 320 234 481 1018 42/350160 L $ 320 234 481 1018 42/350180 M X 375 275 610 1147 48/350200 L X 30 37 400 415 310 665 1202 55/400
190 M 1215 100 70 240
4025-160/11
32-160/11 50
1,5
25-200/01 4034
1283718025
32 80 130
50160132128
160 50132
25 80
1,5
130
132
412130
130
371
371
15132 180 50
180 50 15
2,2
2,2
4
3
3
4
4
M 12350
102
2,2M 12160 102
250
250
102
Base
plat
e an
d/or
fo
unda
tion
desig
n se
e ab
ove
page
22
Pump
Performance Unit dimensionsMotor dimensions
Approximate dimensionsdifferent depending upon manufacturerFeetFlanges
kW
Assignment plug-in shaft/ motor stool
200
371
200
70 190
15
412
100 240
M 12 102250
2,234
102
250
M 12190
50-160/11
3
80 50 100
371
130 130 212160 180 50 15 M 12
250
1024
412350
18,5
100 70 265
50-200/11 80 50 100 15 100412 135 150 160 10235018,522
70 265 212 M 12200 50
65-160/11
4
100 65 65 15 125100 130 155 160 102412 35018,5
22
95 280 212 M 12200
80-160/11 125 80 125 15 125412 145 180 180 10235018,522
95 320 250 M 12225 65
2407010015
32-200/11 50 32 80 100 70 240135 160 180 50 M 12
40-160/11 65 40 80 130 132 160 50
15
40-200/11 65 40 100
18,5
4
412130 140 160
102
100 70 265 212
100 70 240 190
190
Dimensions in mmSubject to alteration
VM 854 GB/11.01 3006 - Ident-No. 796 219 23
ALLHHEEAATT®
Unit dimensions - Series NIWHSizes with a shaft diameter of 32 at the shaft seal
DN
d
DN
s
bfbf
h1h2
a1
d
l
l1f
a
b1b2
h3h3
x
Arrangement of terminal boxonly for motor size 200 L
45°
VM 854 GB/11.01 3007 - Ident-No. 796 219 24
DN
sD
Nd
D
g
Arrangement8 holes
Arrangement4 holes
k
No. ofholes
32 140 18 100 19 440 150 18 110 19 450 165 20 125 19 465 185 20 145 19 480 200 22 160 19 8100 220 24 180 19 8
Flanges acc. to EN 1092-2 PN 16
DNs/DNd D bf k g
Leakageoutlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
G 1/4G 3/8 G 1/4
Connections
G 1/4
Draining Filling/Bleeding
G 1/4 only for vertical
installation
FD2
FD1
FF4FV4
LO1FF2FV1FF2
FV1
LO1
FD2 FD1
Connections for horizontal and vertical installation
ALLHHEEAATT®
n = 1450 / 1750 1/min
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
Pump Motor
size size Exten-
sion
dim.
DNs DNd a f b1 b2 h1 h2 a1 d h3 l1 l x80 0,55 0,75 162 124 234 694 19/200
90 S 181 130 282 742 24/20080 0,55 0,75 162 124 234 702 19/200
90 S 181 130 282 750 24/20090 L 181 130 282 750 24/200100 L 2,2 3 250 203 158 312 780 28/250
80 0,55 0,75 162 124 234 698 19/20090 S 181 130 282 746 24/20090 L 181 130 282 746 24/200100 L 2,2 3 250 203 158 312 776 28/250
80 0,55 0,75 162 124 234 708 19/20090 S 181 130 282 756 24/20090 L 181 130 282 756 24/200100 L 2,2 3 250 203 158 312 786 28/250
80 0,55 0,75 162 124 234 708 19/20090 S 181 130 282 756 24/20090 L 181 130 282 756 24/200100 L 2,2 3 250 203 158 312 786 28/25090 S 181 130 282 756 24/20090 L 181 130 282 756 24/200100 L 2,2 3 203 158 312 786 28/250112 M 228 171 335 809 28/250132 S 412 300 266 196 375 890 38/300
80 0,55 0,75 162 124 234 717 19/20090 S 181 130 282 765 24/20090 L 181 130 282 765 24/200100 L 2,2 3 250 203 158 312 795 28/250
80 0,55 0,75 162 124 234 717 19/20090 S 181 130 282 765 24/20090 L 181 130 282 765 24/200100 L 2,2 3 203 158 312 795 28/250112 M 228 171 335 818 28/250132 S 412 300 266 196 375 899 38/30090 L 200 181 130 282 767 24/200100 L 2,2 3 203 158 312 797 28/250112 M 228 171 335 820 28/250132 S 266 196 375 901 38/300132 M 266 196 375 901 38/300
80 0,55 0,75 162 124 234 725 19/20090 S 181 130 282 773 24/20090 L 181 130 282 773 24/200100 L 2,2 3 203 158 312 803 28/250112 M 228 171 335 826 28/25090 S 181 130 282 755 24/20090 L 181 130 282 755 24/200100 L 2,2 3 203 158 312 785 28/250112 M 228 171 335 808 28/250132 S 266 196 375 889 38/300132 M 266 196 375 889 38/30090 S 181 130 282 783 24/20090 L 181 130 282 783 24/200100 L 2,2 3 203 158 312 813 28/250112 M 228 171 335 836 28/250132 S 412 300 266 196 375 917 38/300
102
5,5
80-160/01 100 100371
130 136 1704
102371
412
162133371 10223027080 120
6550-200/01
1,11,5
50-250/01
65-160/01
102146371
132 225
200102
50 50 103371
148 156 240 225
123 123 200 190
85
300
371
412
156 165 265 245
25085
200102
200
220
102200210
205
371200
123 123
93 190200130124371
13289 371 200180190132
40
32
50
40
32
40 40 97 371
65
80
103
371
65
50
50 50 125 135
130371 125
1,5
1,11,5
4
1,5
1,51,1
1,1
25-200/01
32-160/01
50-160/01
40-200/01
40-160/01
40-250/01
32-200/01
1,11,5
5,57,5
1,11,5
4
1,51,1
5,57,5
1,1
1,11,5
1,1
1,1
5,5
114
65 112
1,5
4
45,5
1,5
103
65
11265
230
200
240
275250
220
250
250
200
245
Assignment plug-in shaft/ motor stool
200
200
250
200
250
102
102200
102
Performance
kW
Motor dimensions
Approximate dimensions
PumpUnit dimensions
different depending upon manufacturerFlanges
65-200/02
300
80 80 102 150 170 275 2354
VM 854 GB/11.01 3008 - Ident-No. 796 219 25
Tolerances of companion dimensionssimilar to DIN EN 735
Sence of rotation: clockwise, as seen from Dimensions in mmthe driving side Subject to alteration
Unit dimensions - Series NIWH
ALLHHEEAATT®
VM 854 GB/11.01 3009 - Ident-No. 796 219 26
n = 2900 / 3500 1/minPump Motor
size size Exten-
sion
dim.
DNs DNd a f b1 b2 h1 h2 a1 d h3 l1 l x90 S 181 130 282 742 24/20090 L 181 130 282 742 24/200100 L 203 158 312 772 28/250112 M 228 171 335 795 28/250132 S 5,5 7,5 412 300 266 196 375 876 38/30090 L 200 181 130 282 750 24/200100 L 203 158 312 780 28/250112 M 228 171 335 803 28/250132 S 5,5 7,5 300 266 196 375 884 38/300160 M 11 15 350 320 234 481 990 42/350112 M 371 250 228 171 335 799 28/250132 S 5,5 7,5 300 266 196 375 880 38/300160 M 11 15 320 234 481 986 42/350160 L 320 234 481 986 42/35090 L 200 181 130 282 756 24/200100 L 203 158 312 786 28/250112 M 228 171 335 809 28/250132 S 5,5 7,5 300 266 196 375 890 38/300160 M 11 15 320 234 481 996 42/350160 L 320 234 481 996 42/350112 M 371 250 228 171 335 809 28/250132 S 5,5 7,5 300 266 196 375 890 38/300160 M 11 15 320 234 481 996 42/350160 L 320 234 481 996 42/350180 M 375 275 610 1125 48/350200 L 30 37 400 415 310 665 1180 55/400132 S 5,5 7,5 300 266 196 375 890 38/300160 M 11 15 320 234 481 996 42/350160 L 320 234 481 996 42/350180 M 375 275 610 1125 48/350200 L 30 37 400 415 310 665 1180 55/400100 L 203 158 312 795 28/250112 M 228 171 335 818 28/250132 S 5,5 7,5 300 266 196 375 899 38/300160 M 11 15 320 234 481 1005 42/350160 L 320 234 481 1005 42/350132 S 5,5 7,5 300 266 196 375 899 38/300160 M 11 15 320 234 481 1005 42/350160 L 320 234 481 1005 42/350180 M 375 275 610 1134 48/350200 L 30 37 400 415 310 665 1189 55/400160 M 11 15 320 234 481 1007 42/350160 L 320 234 481 1007 42/350180 M 375 275 610 1136 48/350200 L 30 37 400 415 310 665 1191 55/400112 M 371 250 228 171 335 826 28/250132 S 5,5 7,5 300 266 196 375 907 38/300160 M 11 15 320 234 481 1013 42/350160 L 320 234 481 1013 42/350180 M 375 275 610 1142 48/350200 L 30 37 400 415 310 665 1197 55/400132 S 5,5 7,5 300 266 196 375 889 38/300160 M 11 15 320 234 481 995 42/350160 L 320 234 481 995 42/350180 M 375 275 610 1124 48/350200 L 30 37 400 415 310 665 1179 55/400132 S 5,5 7,5 300 266 196 375 917 38/300160 M 11 15 320 234 481 1023 42/350160 L 320 234 481 1023 42/350180 M 375 275 610 1152 48/350200 L 30 37 400 415 310 665 1207 55/400
6565 146132412112
210 200
350
102250
103
412
123 123
35032-200/01 40 40 93
412124 130 200 190
170 275 245 350100 130 412 136
170 275 235 35080 102 412 150
162 270 230
156 265 245
250
350
225240
22
10265-160/01 80
4
80 120412
133350
371
65 112412
156 240 225 35050 103 412 148
22412
50 50 103 125 135 220 205
190250
412
371123 102
102
102
102
102
85
100
80
65
102
102
8565 114 412 16522
PumpUnit dimensions
34
3
50
123
350
Performance
kW
2,2
2,2
3
4
4
4
18,5
1903
4
4
200
371
18,5
50
40 97
Motor dimensions
Approximate dimensions
180
200
250
different depending upon manufacturer
371132 132
40
40-160/01
18,540-200/01
80-160/01
65-200/02
18,5
18,5
18,522
22
50-250/01
40-250/01
50-160/01
50-200/01 18,5
18,5
22
22
18,5
32-160/01
50
350
65 125 130 230 220
350
18,5
Flanges
Assignment plug-in shaft/ motor stool
25-200/01 32 32 89 102
1,52,2
Unit dimensions - Series NIWH
Dimensions in mmSubject to alteration
ALLHHEEAATT®
Unit dimensions - Series CIWHSizes with a shaft diameter of 32 at the shaft seal
DN
d
DN
s
bfbf
h1h2
a1
d
l
l1f
a
b1b2
h3h3
x
Arrangement of terminal boxonly for motor size 200 L
45°
VM 854 GB/11.01 3010 - Ident-No. 796 219 27
DN
sD
Nd
D
g
Arrangement8 holes
Arrangement4 holes
k
No. ofholes
32 140 20 100 19 440 150 20 110 19 450 165 22 125 19 465 185 24 145 19 8
Flanges acc. to EN 1092-2 PN 25
DNs/DNd D bf k g
Leakageoutlet
FD1 FD2 FF2 / FV1 FF4 / FV4 LO1
G 1/4G 1/2 G 1/4
Connections
G 1/4
Draining Filling/Bleeding
G 1/4 only for vertical
installation
FD2
FD1
FF4FV4
LO1FF2FV1FF2
FV1
LO1
FD2 FD1
Connections for horizontal and vertical installation
ALLHHEEAATT®
n = 1450 / 1750 1/min
The motor dimensions as indicated are approximate values.Exact data depend on the motor make.
When using special motors, it must be noted that depending uponthe enclosure, different performances are allocated to the individualsizes. The main dimensions are changed accordinagly.Attention: Motors provided by the client must also contain a axialthrust bearing on the drive side!Binding motor dimension information must be submitted with eachorder.
Pump Motorsize size Exten-
sion
dim.
DNs DNd a f b1 b2 h1 h2 a1 d h3 l1 l x80 0,55 0,75 162 124 234 694 19/200
90 S 181 130 282 742 24/20080 0,55 0,75 162 124 234 702 19/200
90 S 181 130 282 750 24/20090 L 181 130 282 750 24/20080 0,55 0,75 162 124 234 698 19/200
90 S 181 130 282 746 24/20090 L 181 130 282 746 24/200100 L 2,2 3 250 203 158 312 776 28/250
80 0,55 0,75 162 124 234 708 19/20090 S 181 130 282 756 24/20090 L 181 130 282 756 24/200100 L 2,2 3 250 203 158 312 786 28/250
80 0,55 0,75 162 124 234 708 19/20090 S 181 130 282 756 24/20090 L 181 130 282 756 24/200100 L 2,2 3 203 158 312 786 28/250112 M 228 171 335 809 28/250
80 0,55 0,75 162 124 234 717 19/20090 S 181 130 282 765 24/20090 L 181 130 282 765 24/200100 L 2,2 3 250 203 158 312 795 28/250
80 0,55 0,75 162 124 234 717 19/20090 S 181 130 282 765 24/20090 L 181 130 282 765 24/200100 L 2,2 3 203 158 312 795 28/250112 M 228 171 335 818 28/250132 S 412 300 266 196 375 899 38/300
65-200/01
1,11,5
371
45,5
65371
1,51,1
130
240
200
148
130
200
190200135130
102220
200210
220 205
102
371200
130 130
10213289 371 200180132 19032
93 37140
32
50-200/011,1
32-200/01
65-160/01
50-160/01
40-200/01
1,1
1,11,5
1,1
5050
1,5
1,51,1
1,5
50
40
135130371103
225
230
40-160/01 97 371 130 130 200 190
4
134
40 40
65 112
11265
50 103
65
Assignment plug-in shaft/ motor stool
200
200
250
200
102
102
102
250
102
Performance
kW
Motor dimensions
Approximate dimensions
PumpUnit dimensions
different depending upon manufacturerFlanges
VM 854 GB/11.01 3011 - Ident-No. 796 219 28
Tolerances of companion dimensionssimilar to DIN EN 735
Sence of rotation: clockwise, as seen from Dimensions in mmthe driving side Subject to alteration
Unit dimensions - Series CIWH
ALLHHEEAATT®
VM 854 GB/11.01 3012 - Ident-No. 796 219 29
n = 2900 / 3500 1/minPump Motorsize size Exten-
sion
dim.
DNs DNd a f b1 b2 h1 h2 a1 d h3 l1 l x90 S 181 130 282 742 24/20090 L 181 130 282 742 24/200100 L 203 158 312 772 28/250112 M 228 171 335 795 28/250132 S 5,5 7,5 412 300 266 196 375 876 38/30090 L 200 181 130 282 750 24/200100 L 203 158 312 780 28/250112 M 228 171 335 803 28/250132 S 5,5 7,5 300 266 196 375 884 38/300160 M 11 15 350 320 234 481 990 42/350112 M 371 250 228 171 335 799 28/250132 S 5,5 7,5 300 266 196 375 880 38/300160 M 11 15 320 234 481 986 42/350160 L 320 234 481 986 42/35090 L 200 181 130 282 756 24/200100 L 203 158 312 786 28/250112 M 228 171 335 809 28/250132 S 5,5 7,5 300 266 196 375 890 38/300160 M 11 15 350 320 234 481 996 42/350112 M 371 250 228 171 335 809 28/250132 S 5,5 7,5 300 266 196 375 890 38/300160 M 11 15 320 234 481 996 42/350160 L 320 234 481 996 42/350180 M 375 275 610 1125 48/350200 L 30 37 400 415 310 665 1180 55/400100 L 203 158 312 795 28/250112 M 228 171 335 818 28/250132 S 5,5 7,5 300 266 196 375 899 38/300160 M 11 15 320 234 481 1015 42/350160 L 320 234 481 1005 42/350132 S 5,5 7,5 300 266 196 375 899 38/300160 M 11 15 320 234 481 1005 42/350160 L 320 234 481 1005 42/350180 M 375 275 610 1134 48/350200 L 30 37 400 415 310 665 1189 55/400
50-160/01
Flanges
40-160/01
3
40
4
4
4
4
18,5
different depending upon manufacturer
Assignment plug-in shaft/ motor stool
32-200/01 32 32 89 102
1,52,2
371
65 130 130 23065 112412
371
220 205412
130130
412
50 50 103
5050 103
65-160/01
65-200/01
18,550-200/01
4
22
18,522
18,5
3
132 132
40
Motor dimensions
Approximate dimensions
180
200
250190
200
4
3
130371
130
130 135
97
2,2
371
102
102
190250
200
350
220
350
102
250
Performance
102
102
102
412
PumpUnit dimensions
kW
2,2
3
35040-200/01 40 40 93
412130 135 200 190
250210
225240 3506565 148134412112
Unit dimensions - Series CIWH
Dimensions in mmSubject to alteration
ALLHHEEAATT®
Subject to technical alterations.
VM 854 GB/11.01 - Ident-No. 796 219