COURSE: Power Generation and Economics COURSE CODE: 15EE42

DEPARTMENT: Electrical and Electronics Engineering SEMESTER: IV

ACADEMIC YEAR: 2016-17 TOTAL CONTACT HOURS: 50

hrs.

DURATION OF IA: 1 hr. IA MARKS: 20

DURATION OF SEE: 3 hrs. SEE MARKS: 80

OVERVIEW: This is one of the important core subjects which an electrical engineering student should study. In this course period, the student will learn the basics of Electrical Power Generation, The sources which are available in nature from which electric power can be harnessed. Also they study about Substation and Grounding in power system.

PRE REQUISITES

1. Basic knowledge about electrical power generation. 2. Basic knowledge about types of electrical power and its components. 3. Basic knowledge about working principle of Motors and Generators.

COURSE OBJECTIVES The main objectives of this course are

1. To make the students study about the different sources of electrical power generation.

2. To teach the students about the process involved for harnessing electrical power from different sources available.

3. To teach the students about the general layout of a substation. 4. To explain the necessity of tariffs and importance of power factor

improvement. 5. To explain the necessity and different methods of grounding.

COURSE OUTCOMES At the end of the course student will be able to:

CO210.1 Discuss about the different sources available for electrical power generation.

CO210.2 Analyse the process involved in generating electrical power using different sources and their environmental issues.

CO210.3 Explain the importance of economic aspects in power generation.

CO210.4 Acquire knowledge about the effects of power factor in setting up the tariff and its improvement.

CO210.5 Explain the operation of a substation, its types, and different Bus bar schemes in a substation.

CO210.6 Summarize the importance of grounding systems and different types of grounding in power system engineering.

CO – PO/PSO MAPPING

CO’S PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO1

0 PO1

1 PO1

2 PSO

1 PSO

2 PSO3

CO210.1 2 - - - - - 2 - - - - 1 - - -

CO210.2 2 - - - - 3 2 - - - 1 2 - -

CO210.3 2 - - - - - - - - - - - - - -

CO210.4 2 2 - - - - - - - - - - - - -

CO210.5 2 - - - - - - - - - - - - - -

CO210.6 2 - - - - 2 - - - - - 1 2 - -

CO210 2 2 - - - 2.5 2 - - - - 1 2 - -

Faculty: D.BABU RAJENDRA PRASAD

COURSE: MANAGEMENT AND ENTREPRENEURSHIP COURSE CODE: 15EE51

Semester: V Academic Year: 2017-18

IA Marks: 20 Exam Hours: 3

Teaching Hours: 40 Exam Marks: 80

COURSE OUTCOMES

Upon successful completion of the course, the students will be able to

CO1 ILLUSTRATE:the management characteristics, functions and importance of

planning(L2)

CO2 CATEGORISE:the types of organizations, nature of directing, and steps in

controlling of the organization (L1)

CO3 DISCUSS:the evaluation the social responsibility and concept of

entrepreneurship and intra preneurship(L1)

CO4 ANALYSE:the objectives, sickness of SSI and impact of globalization,

schemes of institutions on SSI (L2)

CO5 JUSTIFY:the need and significance of project management with report of

different control techniques(L3)

CO mapping with POs and PSOs (Relevance*)

CO PO1

PO2

PO3

PO4

PO5

PO6 PO7

PO8

PO9

PO10

PO11

PO12

PSO1

PSO2

PSO3

CO1 - - - - - - - 2 - 2 - - - - -

CO2 - - - - - 1 - 1 - 1 - - - - -

CO3 - - - - - 1 - - - - - - - - -

CO4 - - - - - 2 - 2 - - - - - - -

CO5 - - - - - - - 3 - 3 - - - - -

CO562

- - - - - 1.3

3 - 1.6 - 1.2 - - - - -

* Note: 1- Low correlation, 2 – Medium correlation, 3 – Strong correlation

CO target for the current academic year

Continuous Internal Evaluation

Semester End Examination

Course Outcomes

Target in %

Target in % 50

CO1 60

CO2 60 Attainment Level

CO3 60 50% students scoring more than set 1

target

CO4 60 60% students scoring more than set

target 2

CO5 60 70% students scoring more than set

target 3

Weightage - CIE 20% + SEE 80%

Faculty: RASHMI S

COURSE: MICROCONTROLLER COURSE CODE: 15EE52

Semester: V Academic Year: 2017-18

IA Marks: 20 Exam Hours: 3

Teaching Hours: 50 Exam Marks: 80

COURSE OUTCOMES

Upon successful completion of the course, the students should be able to

CO52.1 [L2] Describe the complete architecture of 8051, functions of various registers and its

operation with its uses.

CO52.2 [L2] Describe the complete instruction set of 8051and [L5] Write programs in AL for simple

applications

CO52.3 [L2 ] Describe the operations of Timers, Counter and Serial port communication as well

[L3]Design and [L5] Write programs in C for applications related to Timer, Counter and Serial port

communication.

CO52.4 [L5] Interface hardware like DC Motor, Stepper motor, ADC, DAC, LCD, Keyboard, 8255

etc., to 8051

CO mapping with POs and PSOs (Relevance*)

CO PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2 PSO3

CO1 3 3 - - - - - - - - - - - - -

CO2 3 3 3 - - - - - - - - - - 3 -

CO3 3 3 3 - - - - - - - - - - 3 -

CO4 3 3 3 - - - - - - - - - - 3 -

CO562 3 3 3 - - - - - - - - - - 3 -

* Note: 1- Low correlation, 2 – Medium correlation, 3 – Strong correlation

CO target for the current academic year

Continuous Internal Evaluation Semester End Examination

Course Outcomes Target in % Target in % 40%

CO1 60

CO2 60 Attainment Level

CO3 60 50% students scoring more than set target 1

CO4 60 60% students scoring more than set target 2

70% students scoring more than set target 3

Weightage - CIE 20% + SEE 80%

COURSE: POWER ELECTRONICS COURSE CODE: 15EE53

Department: EEE No. of lecture hours/week - 4

Academic Year: 2017-18 Semester: VII

Teaching Hours: 50 Exam Hours: 3

Exam Marks: 80 IA Marks: 20

Prerequisites: Knowledge of Laplace Transformation, Fourier Analysis, Kirchhoff’s

Voltage Law, basic concepts of transistors and diodes.

Course Overview

After studying this subject, students will be able to analyse different power electronic

converters

Course Objectives

The objectives of this course are to

Give an overview of applications power electronics, different types of power semiconductor devices, their switching characteristics.

Explain power diode characteristics, types, their operation and the effects of power diodes on RL circuits.

Explain the techniques for design and analysis of single phase diode rectifier circuits.

Explain different power transistors, their steady state and switching characteristics and limitations.

Explain different types of thyristors, their gate characteristics and gate control requirements.

Explain the design, analysis techniques, performance parameters and characteristics of controlled rectifiers, DC- DC, DC -AC converters and Voltage controllers

Course Outcomes After completing this course students will be able to

CO1 Explain the types of power diodes, their characteristics and analyze single phase diode rectifiers

CO2 Analyze steady state, switching characteristics and gate control requirements of different power transistors and their limitations

CO3 Describe different types of thyristors, their operation, gate characteristics, gate control requirement along with applications and design of snubber circuits

CO4 Analyze single phase and three phase thyristor controlled rectifiers and AC voltage controllers with R and RL load

CO5 Analyze the principle of operation of DC –AC converters and DC- DC

Course

Outcomes

PO

1

PO

2

PO

3

PO

4

PO

5

PO

6

PO

7

PO

8

PO

9

PO

10

PO

11

PO

12

PSO

1

PSO

2

PSO

3

CO1 1 1 - - -

- - - - 2 - -

- - -

CO2 - 2 - - - - -

- - - - - - 1 -

CO3 3 2 2 - - - -

- - - - - - - -

CO4 2 3 - - - - -

- - - - - 1 2 -

CO5 2 3 - - - - -

- - - - - 1 2 -

Avg 2 2.2 2 - - - - - - 2 - - 1 1.67 -

converters

COURSE ELECTRICAL ESTMATION AND COSTING

(Professional Elective) COURSE CODE 15EE553

DEPARTMENT Electrical and Electronics Engineering SEMESTER V

ACADEMIC YEAR 2018-19 TOTAL CONTACT HOURS 40 hrs.

DURATION OF IA 1 hr. IA MARKS 20

DURATION OF SEE 3 hrs. SEE MARKS 80

COURSE SYLLABUS MODULE 1 PRINCIPLES OF ESTIMATION 8 Hours Introduction to Estimation and Costing, Electrical Schedule, Catalogues, Market Survey and Source Selection, Recording of Estimates, Determination of Required Quantity of Material, Labour Conditions, Determination of Cost Material and Labour, Contingencies, Overhead Charges, Profit, Purchase System, Purchase Enquiry and Selection of Appropriate Purchase Mode, Comparative Statement, Purchase Orders, Payment Of Bills, Tender Form, General Idea about IE Rule, Indian Electricity(IE) Act and IE Rules -29,30,45,46,47,50,51,54,55,77 and79 MODULE 2 DOMESTIC WIRING ESTIMATION 8 Hours Introduction, Distribution of energy in a Building, PVC Casing and Capping, Conduit Wiring, Desirabilities of Wiring. Types of cables used in Internal Wiring, Multi Strand Cables, Voltage Grading and Specification of Cables. Main Switch and Distribution Board, Conduits and its accessories and Fittings. Lighting Accessories and Fittings, Types of Fuses, Size of Fuse, Fuse Units, Earthing Conductor. General rules for wiring, Design of Lighting Points (Refer to Seventh Chapter of the Textbook), Number of Points, Determination of Total Load, Number of Sub –Circuits, Ratings Main Switch and Distribution Board and Size of Conductor. Current Density, Layout. MODULE 3 SERVICE MAINS AND DESIGN AND ESTIMATION OF POWER CIRCUITS 8 Hours Introduction, Types, Estimation of Underground and Overhead Service Connections. Introduction, Important Considerations Regarding Motor Installation Wiring, Input Power, Input Current to Motors, Rating of Cables, Rating of Fuse, Size of Condit, Distribution Board Main Switch and Starter. MODULE 4 ESTIMATION OF OVERHEAD TRANSMISSION AND DISTRIBUTION LINES 8 Hours (Review of Line Supports, Conductor Materials, Size of Conductor for Overhead Transmission Line, Types of Insulators) [No Question Shall be Set from the Review Portion]. Cross Arms, Pole Brackets and Clamps, Guys and Stays, Conductors Configuration Spacing and Clearances, Span Lengths, Lightning Arrestors, Phase Plates, Danger Plates, Anti Climbing Devices, Bird Guards, Beads of Jumpers, Muffs, Points to be Considered at the

Time of Erection of Overhead Lines, Erection of Supports, Setting of Stays, Fixing of Cross Arms, Fixing of Insulators, Conductor Erection, Repairing and Jointing of Conductors, Dead End Clamps, Positioning of Conductors and Attachment to Insulators, Jumpers, Tee-Offs, Earthing of Transmission Lines, Guarding of Overhead Lines, Clearances of Conductor From Ground, Spacing Between Conductors, Important Specifications. MODULE 5 ESTIMATION OF SUBSTATIONS 8 Hours Main Electrical connection, Graphical Symbols for Various Types of Apparatus and Circuit Elements on Substation Main Connection Diagram, Single Line Diagram of Typical Substations, Equipment for Substation, Substation Auxiliaries Supply, Substation Earthing.

OVERVIEW: This is one of the professional elective subjects which an electrical engineering student should study. In this course period, the student will learn about the Basics of and Need for Estimation and Costing. The students study about the process that is carried out while doing an estimation for electrical work such as for Domestic premises, Service mains, Power circuits, Substations and Overhead Transmission lines. The mere cost of all the components are tabulated and the final estimation table is prepared.

PRE-REQUISITES 4. Basic knowledge about domestic wiring. 5. Basic knowledge about electrical components used in Transmission and Distribution. 6. Basic knowledge about Substations.

COURSE OBJECTIVES The main objectives of this course are to make students 6. Understand the Basics of Estimation and Costing. 7. Discuss about the need for Market Survey, Source selection, Determination of

material and Labour cost. 8. Prepare an Estimate of the materials required for any electrical installation and

calculate the approximate cost for the job

COURSE OUTCOMES

At the end of the course student will be able to

C305.1 Explain the purpose of estimation and costing and the processes involved in Estimating and preparing the final cost.

C305.2 Discuss about the distribution of energy in a building, General rules for wiring and its methods, wiring accessories and fittings, fuses and types of fuses, types of service mains.

C305.3 Design and estimate the cost for a power circuit and Service mains.

C305.4 Prepare an estimate of overhead transmission and distribution system.

C305.5 Choose the main components for a substation and prepare single line diagram for a substation.

CO – PO/PSO MAPPING

PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2 PSO3

C305.1 2 2 2

C305.2 2 2 1

C305.3 2 2 2 2 2

C305.4 2 2 2 2

C305.5 2

C305 2 2 2 2 2 1.7