VISTA-KM512-PCI-DC-English Manual V.0711.pdf

VISTA DIGITAL INKJET PRINTER MANUAL

Beijing Innovation Technology Co.,Ltd. PAGE 1

www.jhfvista.com TEL86 10 62950101 FAX86 10 82410746

1 CHAPTER PROLOGUE .................................................................................................................................. 5

1.1. DESCRIPTION ............................................................................................................................................. 5

1.2. SAFETY PRECAUTIONS! WARNING!............................................................................................................ 7

1.3. THE MODEL IMAGE OF VISTA INKJET PRINTER ........................................................................................... 8

1.4. MANUAL CATALOGUE FOR VISTA INKJET PRINTER .................................................................................... 9

2 CHAPTER 2: EQUIPMENT STRUCTURE AND PERFORMANCE....................................................... 12

2.1. COMPOSING ................................................................................................................................................. 12

2.2. SYSTEM PERFORMANCE........................................................................................................................... 12

2.2.1 Mechanism System:.......................................................................................................................... 12

.2.2.1.1 Media Movement System ................................................................................................................ 14

2.2.1.2 Carriage Movement............................................................................................................................ 14

2..2.2 Electric System .................................................................................................................................. 15

2.2.2.1 Electricity Control Diagram............................................................................................................... 15

2.2.2.2 Control Box Map................................................................................................................................ 16

2.2.2.3 Heating System............................................................................................................................. 17

2.2.3Ink Supply System................................................................................................................................... 19

2.2.4. The Control System .............................................................................................................................. 21

2.2.4.1 Computer Configuration Request: ..................................................................................................... 21

2.2.4.2. Boards, Connections and diagram .................................................................................................... 21

2.2.4.3 the control system of electrical board image and connection for the control system................... 22

2.2.4.4. OPERATING INSTRUCTION FOR THE MACHINE SWITCHES................................................................... 24

2.2.5. Maintenance......................................................................................................................................... 26

3 OPERATION INSTRUCTION ...................................................................................................................... 28




3.1 Operation sequence outline...................................................................................................................... 28

3.2 Operation Instrutions ............................................................................................................................... 29

3.2.1 Power Operation ................................................................................................................................... 29

3.2.2. Feeding the Media................................................................................................................................ 29

3.2.3. Installation Print head.........................................................................................................30

3.2.4 Testing the Electric Circuit Board ....................................................................................30

3.2.5 Check the Raster Positioning System...............................................................................31

3.2.6. Ink Supply............................................................................................................................................. 31

3.2.7. Start Printing.......................................................................................................................32

3.2.8. End Printing.....................................................................................................................32

4 THE WAY OF DEALING WITH THE IMAGE FOR THE VISTA SOFTWARE..................................... 33

4.1 DESIGN IMAGE......................................................................................................................................... 33

4.2 CHANGE THE IMAGE AS CMYK FORMAT ................................................................................................. 33

4.3 SETTING IMAGE SIZE ............................................................................................................................... 34

4.4 MERGE IMAGE LAYERS............................................................................................................................ 35

4.5 SAVE THE IMAGE FILE............................................................................................................................... 36

5 RIP SOFTWARE PHOTOPRINT GUIDE.................................................................................................... 38

5.1 INSTALL PHOTOPRINT.......................................................................................................................... 38

5.2 SET THE PRINTER ..................................................................................................................................... 38

5.3 ADD ICC ALIGN FILE ............................................................................................................................... 40

5.4 SET THE PRINT JOB ................................................................................................................................... 41

5.5 SEND THE OPERATION .............................................................................................................................. 47

5.6 CONTROL SOFTWARE AND THE CONNECTION OF PHOTOPRINT SOFTWARE ......................................... 48




5.7 THE NOTICE FOR PHOTOPRINT............................................................................................................. 48

6 THE BASIC OPERATION OF THE PRINTING SYSTEM ....................................................................... 49

6.1. THE CHARACTERISTIC OF THIS PRINTING SYSTEM: ................................................................................... 49

6.2. PRINTING SOFTWARE INSTALLATION........................................................................................................ 49

6.2.1. Control Software Installation ............................................................................................................... 49

6.2.2. PCI Card Installation ........................................................................................................................... 50

6.3. THE APPLICATION FOR CONTROL SOFTWARE............................................................................................. 50

6.3.1. Printer Configuration........................................................................................................................... 50

6.3.2. Main Page ............................................................................................................................................ 51

6.3.3. Main Menu ........................................................................................................................................... 51

6.3.4. Keyboard Shortcuts .............................................................................................................................. 54

6.3.5. Default Parameter, Shortcut icon ......................................................................................................... 54

6.3.6. Printing Mode ...................................................................................................................................... 56

6.3.7. The array of print heads ....................................................................................................................... 58

6.3.8. Automatic Vacuum cleaning ................................................................................................................. 59

6.3.9. STATUS BAR ........................................................................................................................................ 59

6.4. FIBER INSTALLATION: .............................................................................................................................. 60

7 DAILY MAINTENANCE AND REPAIR ...................................................................................................... 61

7.1. Operating environment request............................................................................................................... 61

7.2 Operation & Maintenance Requirement .................................................................................................. 61

7.3. PRINT HEAD MAINTENANCE..................................................................................................................... 63

7.3.1. Print head maintenance reason............................................................................................................ 63

7.3.2. The tactic of maintenance..................................................................................................................... 64




7.3.3. Print Head Maintenance ...................................................................................................................... 64

7.4. THE MAINTENANCE FOR THE SYSTEM OF M MODEL ................................................................................. 66

8 DAILY TROUBLESHOOTING..................................................................................................................... 67

9 KONICA MINOLTA PRINT HEAD INTRODUCTION ............................................................................. 73

9.1. HOW TO PROTECT THE PRINT HEAD .......................................................................................................... 73

9.2. PRINT HEAD DESCRIPTION....................................................................................................................... 75

9.3. THE INK INSIDE MOVEMENT DIRECTION ................................................................................................... 75




1 Chapter Prologue 1.1. Description

The VISTA series Large Format Digital Inkjet Printer is produced by Beijing JinHengFeng Digital Science & Technology Development Co., Ltd. It is digital equipment, which is controlled by the computer, can output colorful images automatically. It adopts automatic colorful output, which is controlled by computer, and all of the digital equipment makes sure the easy operation.

1.1.1 The Expected aim

It can be used for outdoors printing such as billboards, bus advertisement, light box, poster, display, stage backgrounds, signboards, and etc, which needs durability and high speed.

1.1.2 The media:

Solvent- based flexes, paper, banner, mesh, vinyl and so on. Any media manufacturer is ok, but good quality media is strongly suggested to get great printing impact and long lifespan printing outdoors.

1.1.3 The Ink

Solvent based inkoil based ink, UV ink this is up to the print head model and ink supply system and resolution.Any ink manufacturer is ok, but good quality ink is strongly suggested to extend the print heads life, get great printing impact, and longer lifespan printing outdoors.

1.1.4 The Print-Heads

Print heads of British XAAR Company and American SPECTRA Company, Japan Seiko and Japan Konica. With the development of market, more print-heads will be optional.

1.1.5 The RIP Software

Maintop, Photo print, Wasatchdifferent control system with different RIP.

1.1.6 Models

Media width: 1.8m, 2.5m, 3.3m, 3.5m, 5m

1.1.7 Print-head quantity:

Konica: KM512 (MN/14PL, LN/42PL) 4 print heads/ 4 color, 6 print heads/ 6 color, 8 heads/4 color




Konica KM256 (MN/14PL, LN/42PL) 4 print heads/ 4 color, 6 print heads/ 6 color, 8 heads/4 color

Xaar XJ500: 4 print heads/4colors, 6 print heads/6 colors

Xaar XJ128/200: 8, 12 print heads/4 color12 print heads/6 color

Xaar XJ128/360: 8, 12 print heads/4 color12 print heads/6 color

Spectra 256: 4, 8 print heads/4 color

Spectra skywalker 128 8, 12, 16 print heads/4 color12 print heads/6 color

Servo System: AC, DC Working Station: WIN98, WINXP Printing Port: PCI, USB Shape: M, V, A, and so on..

Non-Guarantee Spare Parts of the Equipment

Print-heads, ink-pumps, filters and ink tubes

1.1.8 Warranty

One year since the machine left factory.

1.1.9 Non-warranty Items

The warranty doesnt cover the force majeure and user damage.

1.1.10 Package

Legs assembled and legs unassembled, suffocated and un-suffocated veneer case, vacuum and non-vacuum covers are optional.

1.1.11 Operators

One or two operators, which is familiar with computer, electronics, electrics and mechanism, and got professional printing training.

1.1.12 Environment

Power: 220V, 50HZ, single-phase, AC




Temperature: 20-28

Humidity40%-60% the temperature watch and barothermohy grogram must be installed

Air: 0.7 MPA dry air, dustproof device, and ventilation device.

Regulator: 1KVA UPS

Grounding: The printer must be grounded; the earth-plate must be firm and effective, so that the printer can prevent itself from static and leakage. If you dont have the standard grounding device in the workshop, you must do as the following:

Dig a hole of 1 meter-length,1 meter-width and 1.5 Meter-depth, put one piece of metal plate, especially copperplate, of 10mm-thickness and connect a lead wire to the ground as the grounding end. You should not use the pipe or the conductor you think of. The static of the printer can not be higher than 5V!

1.2. Safety Precautions! Warning!

Vista printers are designed accord with all the safety requirements of printing equipments. But to ensure 100% safety, the operator should follow the safety precaution and operation instruction of this manual and the improved version in future seriously.

Only the operator who is correctly trained and qualified to operation can be allowed to do installation & maintenance.

Without JHFs written permission, any modification, deletion, or replacement of the printer is prohibited; or the machine warranty will be invalidate immediately.

The operator should learn this manual seriously and keep the manual somewhere, which is easy to get.

Since the equipment is a separate system, please do not use same power supply with other power-eating equipments or electric interferential equipments to prevent the machine from electric harm.

During the process of equipment works, the abruptly power off or Over-strong voltage (current) will bring to un-forecast damages.

Neither let the equipment works near flammable liquid or gas, nor under the environment of excessive dry and wet place.

To prevent the electronic parts from hot, please do not block the intake.


Beijing Innovation T

www.jhfvista.com

The computer is only used for controlling the printer. You are recommended that you wont install any other software except the printing software lest occur the software interference caused by virus or different RIP software, and decrease the working speed and even the computer freezes suddenly. You are also recommended that you have another computer for designing the RIP file purpose. When the RIP file is ready, you save it in the printers computer. You are recommended to delete the file or save the file in disc, floppy disc or other computer after the file has been printed instead of saving the file in the printers computer.

The ink and solution ar harmful for peoples eyes and skin; you should clean it as soon as it splashes into the eyes. Please ke

The ink and solution against the volatilizatinvalidation. The invalused.

Please make sure there

It is strongly suggestedof the printer.

Some cables in chain should be fixed tightly-signal.

It the equipment can noand repair, and also you

JHF Company can nooperate, test and calibra

JHF Company has righyour purchased machimachine.

1.3. The model image

eechnology Co.,Ltd. PAGE 8

TEL86 10 62950101 FAX86 10 82410746

ep the ink and solution away from the children.

have the property of volatilization, so you should cover it when it isnt used ion of the efficient components, which may cause the ink and solution id ink will damage the print head. The ink should be shook before it will be

is no ink on the electric circuit board and cables lest circuit short or turn-off.

that you turn off the general power before you disconnect or connect any parts

along the print-head carriage move frequently, so the connection on both ends in case the strong movement causes the phenomenon of incomplete sending

t work normally, please check the troubleshooting and make some maintenance should contact with service department of JHF Company to get some help.

t promise that once a person read this manual then he/she can be eligible to te this printer.

t to explain this manual, and can not ensure this manual is totally in line with ne model due to the market change. Please ask latest manual to match your

of Vista Inkjet Printer




Image 1-1M model

(Image 1-2 )V model-KONICA print head

(Image 1-3 )V model -KONICA-print head

(image 1-4)A model KONICA print head

1.4. Manual Catalogue for Vista Inkjet Printer

model

VISTA10000: adopt KONICA KM512MN 14PLprint head

VISTA9000: adopt KONICA KM512LN 42PLprint head

VISTA8000: adopt KONICA KM256MN 14PL print head

VISTA6000: adopt KONICA KM256LN 42PL print head

The standard default for printeryou can check the configuration demand on the standard default




Signal definition for printer

X XX OX X X X

S means 6 color, without S means 4color

N means 14PL, without N means 42PL

F means KM512 print head, E means KM256 print head

4, 6, 8 is the quantity of print heads

50, 33, 26, 25, 22, 18 is the printing width of the printer: 5m, 3.3m, 2.6m, 2.5m, 2.2m, 1.8m

A, V is the printer shape and body

For example A3306ENS stand for A model, 3.3m, 6 print heads, konica256, 14PL, 6 color

The parameter for the model:

Specification A3308E A2604E

A2606ES

A2606ENS

A2604EN

A1606ENS

A1604EN

V3304F

V3306FS

V2504F

V2506FS

V2504FN V1804FN

V2506FNS

V1806FNS

L*W*H 4410*800*1350

3760*800*1350

3760*800*1350

2760*800*1350

4750*930*1280

4100*930*1280

4100*930*1280

3350*930*1280

Weight 600KG 530KG 530KG 460KG 520KG 450KG 450KG 380KG

Max Resolution 720DPI 720DPI 1440DPI 1440DPI 720DPI 720DPI 1440DPI 1440DPI

Printing Speed(m

56 2/h)

26 24 24 40 37 22 19

Power Supply Single Phase, AC, 220v50hz Power 0.8KW includes single heater, 1.3KW includes two heaters, 1.75KW includes

three heater Ink Solvent Ink C M Y K LC LM Ink Supply Automatic continuously ink supply by pump, positive cleaning RIP Photoprint or Wasatch Positioning Optical Encoder Position (Raster)




Head & MediaDistance

2-3mm, adjustable

Media Control Roll to roll, (80KG/roll, out diameter235mm), automatic/manual feeding and collecting

Media Suction Media Suction under the printing table Heating Pre-heater and Post-heater, separate temperature control and display Drying Front Fan Head Maintenance

Automatic Vacuum Cleaning, Positive Cleaning, Head Cover to keep head wet

Media PVC, Vinyl, Mesh, Non-woven Textile, File TIFF (RGB&CMYK), BMP, JPEG Interface High Speed PCI Card Data Transferring

Optical Fiber

Working Station

WINXP




2 Equipment Structure and Performance 2.1. Composing

Mechanism System

Electrical System

Ink-supply System

Control System

Maintenance System

2.2. System Performance

2.2.1 Mechanism System:

It includes media movement system and carriage movement system. The structure map of the mechanism

system is as follows




Picture 2-1VISTA-UM/V model -Mechanism System




.2.2.1.1 Media Movement System

Media Movement System includes initiative movement system and driven movement.

Initiative movement system:

It includes stepping- motor driver, stepping motor, reducer and initiative roller.

The initiative movement system can move or stop after receiving the order of printing software from the computer. The moving orientation and distance of the media can be changed by the way of changing the relevant parameters in the software. For more details of the parameters adjustment in the software, please refer to software explaining chapter.

Driven movement system:

It includes Reducer, single phase motor and winding roller. The media roller switch on the panel of the printer controls the movement of the driven movement system.

2.2.1.2 Carriage Movement

The Movement System of the Print head carriage is also named as Servo Control System. It includes Servo Motor, Reducer of Servo Motor, Driver of Servo Motor and Feeding Belt.

The print head carriage receives the order from the printing control software in the computer, and it will move or stop through the feeding belt. The movement of the Servo Motor is controlled by the Driver of the Servo motor. The adjustment way of the parameters for the Servo motor is as follows.


Beijing Innovation Technology Co

www.jhfvista.com TEL86 10

Print Head Fixation Screws

2..2.2 Electric System

2.2.2.1 Electricity Control Diagram

(Picture 2-2) Electricity Control Syst

.,Ltd. PAGE 15

62950101 FAX86 10 82410746

em




2.2.2.2 Control Box Map

Picture 2-3 V model-PCI sytem-SPT510 print head machine Electricity Control diagram




Picture 2-4 UM model-PCI sytem-SPT510 print head machine Electricity Control diagram

2.2.2.3 Heating System

(Picture 2-5) Heating System Diagram

Note: Heater controller, namely thermostat




Heater ControllerSwitch

(Picture 2-6) Thermostat panel diagram

Indicator:

AL1: Indicator of Relay J1

AL2: Indicator of Relay J2.

AT: Self-adjustor Indicator (blinking during self-adjusting)

Parameter adjust button -up /increase button

Parameter adjust button-down/decrease butto

Replacement Button/Self -adjustor button

Set/ok

Controller display

Heater Controller Parameter Settings Illumination

Initial Parameters: (press , enter password to enter the system)

parameter Marks Meaning Option/Scope Initial Parameter

inty inty Heat Sensor Model See Pic 2-8 Pt 10.0 outy outy output Control Mode 0,1,2 2 2 caty caty PID Control Arithmetic 0,1,2 0 0




Psb

Psb sensor Error amend parameter

-100~100 0

Rd

Corf

end

Rd

Corf

end

running model

Unit option

end

0:heating 1:cool

0: 1:of

0

0

1. Pressing the increase or minish switch when the thermostat is working, the panel window will show

temperature setting value (SV). Press the increase switch, the temperature setting value will add 1 and

press the minish switch, the temperature setting value (SV) will decrease 1.

2. The temperature setting and alarm setting is same as initial parameters setup.

3. Relay connection value and break value illumination.

If you set AH1=AL1, or AH2=AL2, the relay cannot work;

If you set AH1>AL1, or AH2>AL2, relay works, it is used to up limit alarm;

If you set AH1




Note

1), A, electric magnetic valve; B, air pump C, reset switch D, filter

2), Press the reset switch then the electric magnetic valve and air pump begin to press ink separately

3), ink supply system

*Ink Supply: when the ink is on the bottom, floater sensor is on the bottom of the sub ink tank, it gives the signal of connection, the ink supply board and the main ink tank is connected by the 24V, and the pump works, the ink is going to the ink tank; when is on the upper limit level, the floater sensor gives the break signal, ink supply is stopped. During printing, the ink in sub ink tank will falls gradually, after the ink supply, the ink level increases again. It means the ink will be kept in a suitable scope to keep the printing works well.

*Lack-ink Alarm: when the ink in the main ink tank is going finishing, the pump will keep working because the connection signal keeps. When the pump works out of the time limit (the time to fill two sub ink tanks time under the normal ink supply condition), the ink supply board will alarm and the indicator will blink to remind the operator to fill the ink.

4) Electromagnetic valve ink cleaning system diagram




(1)The electronic circuit of electromagnetism valve and air pump is link parallel, and they will work together and press the ink automatically to meet the aim of balancing the air pressure.

2Press the ink: Press the button, the air pump press the air to electromagnetism valve and it will work, this time B and A is thorough to keep the effect of press ink.

3Printing: loose the button, the air pump and electromagnetism valve all stop working, now the A and C is thorough to keep the balance of ink box pressure.

4Cleaning the ink from the surface of print head and beginning working.

2.2.4. The Control System

The controlling system of VISTA printer consists of computer (software included), relevant electronic circuit board, the controlling switch, electronic cable etc.

2.2.4.1 Computer Configuration Request:

Work station:: WINDOWS XP

MAINBOARD: Intel suggested

CPU: above Pentium IV, 2.4 G

MEMORY: 512 M DDR

Hard disk: 80G, High Speed RS 720020G free memory for use

Display: 64M/8X

Computer device provide by the customer themselves

2.2.4.2. Boards, Connections and diagram

Coordinate:




Printhead setting order

Front View Rail

Carriag Power

Heater

2.2.4.3 the control system of electrical board image and connection for the control system.

make sure the connection of AB port is good. Make sure the connection of FCC is good. When you insert or pull out the PCI card, make sure the computer is off. After you installed PCI card, must fix it use the screw. Forbid to insert or pull out the yellow signal cable for the PCI card and high thick cable.




Picture 2-11Color board(left),PCI card (right ), Servo motor (bottom ) indicator light and connector diagram

1. 12V/24V Power Input Switch Power Supply

2. Position Limit Switch, Emergency Stop Switch

24V Power Input Step Motor

Servo Card 3. Stepping Signal Output Driver 24V Output

Control Signal Output

4 Ink Pump Power Cable Ink Pump

5 Floater Sensor Cable, Raster Signal Cable Color Board

6 Vacuum Cleaning Signal Vacuum Cleaner Power Output

Serial Port A 24V Power Input Servo Motor

PC 7 Servo Signal Output 24V Output

Optical Fiber B Control Signal Output

Color Board




Picture 2-12Electric distributor board connector diagram

2.2.4.4. Operating Instruction for the machine switches

notethe position of the switch for V model and UM model if differentplease peruse what you need.




Picture 2-14V Model operation switches diagram

Picture 2-159- switch panel diagram




3. Control Panel and switches functions:

Emergency Switchpresses it down, it will break the servo motor driver (encoder) power, and the carriage will stop movement. When the printing has something abnormally, you have to stop the machine running immediately; you can press this button down. This operation will prevent the print heads and other components from damage, but it will also lose the printing, you must print it again. Please do use this button carefully

Switch 9(general power switch): Press it down, the light will turn on and the machine gets the power. Also, it connects 5v/24 v, 48 v power supply board and supply the power for the servo motor driver.

Switch 8(fan switch): Press it down, the light will turn on and the machine gets the power. Also, it connects 5v/24 v, 48 v power supply board and supply the power for the servo motor driver.

Switch 3 (print head switch): Press it down, the light will turn on and the print head gets the power. Also, it connects 35v power supply board.

Switch 1, 2, 3,5,6,7 switches: Press it down, the light on it will turn on and it connects single phase power, controlling the feeding and take-up rollers.

Machine operation order

To make sure if the printer is out of power Press down general power switch and the machine gets the electricity when the indicator light is on Open the computer to run the JHF Printing Management. Press the print head switch down, the light indicator turns on, the print head gets the power. If the output is almost dry, please press down the fan switch. Press the automatic feeding advance, automatic feeding reverse, manual take-up advance and manual

take-up reverse. Please note that it is not allowed to press down two switches or more than two switches. Otherwise, the single direction power will not run.

The order of turn off: Turn off the print head power, turn off the computer power, and then turn off other witches to make all light indicators off. Finally, turn off the general power switch and let the light off.

2.2.5. Maintenance

To maintain the machine, you need: one pc of vacuum cleaner;

Print Heads Cleaning Tools: injector, test paper, solvent.

Vacuum cleaner: it is used to clean the print head during the printing, controlled by the software. The user is required to connect the vacuum cleaner tube and vacuum terminal tightly as the picture 2-16.




The vacuum cleaner is prepared by the user. It is suggested to use dry-wet multiple use type vacuum cleaner, with about 1000 w power.

Picture 2-16Automatic Cleaning Terminal Picture2-17Print head protection tray

3Cleaning print head tool: The user needs non-spin fabric, injector, test paper, and solvent to clean the print head.

4. The machine is equipped with a print head protection salver as the picture 2-7. The end-user can put the solvent into the antisepsis sponge and cover the tray below the print head carriage holder after stopping printing but with the print heads on the machine. When you doing that, please make sure the tray covers the print heads and absorb the magnet against the print head carriage holder. It can last the print head wet for at most 8 hours if there isnt any space. If there is any space between the magnet and print head carriage holder, please use the antisepsis sponge for replacement. It is not absolutely safety way. It is just a kind of convenient tool.

Note: when the general power or the power for the print head is on , do not use the protection salver, or else the circuit in the print head will be disturb, and affect the print head.




3 Operation Instruction 3.1 Operation sequence outline

1) Please put the package at working place. Prevent it from shaking.

2) Please disassemble the crate step by step and check the spare parts according to the attached package list. Using a forklift to move the printer to the working house.

3) Check if the printer is put at a good level.

4) Move away all fastened spare parts from the print head carriage and install all the spare parts.

5) Move the print head carriage by hand to make sure if the print head carriage belt and linear encoder sensor are installed in suitable position.

6) Grounding the printer to make sure the static voltage is below 1 V.

7) Put the PCI card inside the computer and connect the flat cable and movement controlling cable between the computer and printer and also check its other power cables and signal cables to make sure they are connected well and rightly.

8) Install the printing software and RIP software with the computer.

9) When turn on the printer, please put the hand nearby the emergency switch to deal with the accident.

10) Send a file to the printer to check the printing

11) Turn off the printer. Please fix the print head and then fix the signal cables between the print head and transforming board.

12) Please clean the print head one by one with the cleaning solution. Please keep the cleaning solution in the print head at least 10 minutes in order to get ride of the protection liquid inside the print head absolutely. Additionally, please let off the cleaning solution from the print head completely.

13) Connect the ink supply system, which supplies the ink.

14) Please use the positive or negative pressure to make the ink out of the print head, and then wipe off the superfluous ink on the print head face.

15)Printing color bar to see how the print head jets ink


Beijing Innovation Technology Co.,Ltd.

www.jhfvista.com TEL86 10 6295

16) Adjusting the print head

3.2 Operation Instructions

3.2.1 Power Operation

UM model: turn on the printer general power witch breaker (AC 220V, 50HZ, make it sure the power socket is connected to the ground well). V model: turn on the general power on the control panel. Turn on the computer with Windows XP, install PCI card and its driver and printing software.

(Please refer to the software installation manual). Before printing, please make it sure that the distance switches work well. It needs two people to

operate. Operator A operate the computer, moves the carriage to right side by software, the operator B press the right distance switch, the carriage will stop immediately at normal condition. And then press down the emergency switch, and loose the right distance switch. Repeat it to make it sure the right distance switch is ok. A moves the carriage to left, B presses the left distance switch, the carriage will stop at the normal condition. Repeat it, make it sure the left distance switch is ok. Operate the software, control the each part of the machine movements, and confirm the machine

is ok.

3.2.2. Feeding the Media

(Picture 3-1) V Model Feeding Structure

PAGE 29

0101 FAX86 10 82410746

(Picture 3-2) UM Model Feeding Structure




A Model Feeding Structure

Please put the media between the two feed rollers, thread through the feeding wheels and press wheels, align the media edge, press the media handle, move the media and see if it is flat or not. If not, please do it again.

3.2.3. Installation Print head

Firstly, please fix the print head, secondly, connect the ink tube and print head ink inlet tubes and thirdly connect the cable between the print head and transforming board. Please remember to block the outlet after the print head can jet.

Cleaning print head: Clean the print head one by one with the cleaning solution. Please keep the cleaning solution in the print head at least 10 minutes in order to get rid of the protection liquid inside the print head absolutely. Additionally, please let off the cleaning solution from the print head completely.

When installing or uninstalling the print heads, please do not turn on the printer power. Please

wear special gloves to keep from static. The static will damage the small print heads chips and print heads.

3.2.4 Testing the Electric Circuit Board

Testing the color boar: The light for the 12v and 24 are on and these lights are winking when the computer loading the program, but not printing. If so, it means that the color board is working well.




Print head chip: If the light on the chip glitters, it means that the chip is working well.

The servo motor board: The status light shines, the ink supply light is on when supplying ink and the 12v and 24 v indicators light is on all the time and distance switch indicator light is off all the time. If so, it means that the servo motor board works well.

PCI card: The power indicator light is on, the direction light is on when moving and two lights are on all the time when working. If so, it means that the PCI card works well.

3.2.5 Check the Raster Positioning System

Check if the raster is installed well or not: it should be straight and tension, the blocks should be close to the raster, and the two sides should be fixed firmly.

Check the Raster sensor: should be 1-2mm to the raster top edge.

Check raster: if there is scar, or there is ink, oil on it.

3.2.6. Ink Supply

Supply the ink to the sub ink tank:

A) Make sure all the ink tube is connected well.

B) Turn-on the printer general power.

C) Connect the ink level sensor of each color to floater accordingly.

D) Make sure 4 or 6 ink pumps to start work and second ink tank refilling the ink.

When you turn on the ink-supply power, the indicator light which is on the ink-supply board will be shining, and

ink-pumps will be turning. Then the secondary ink tank will reserve ink and the pump will stop working. It is because when

The ink rises to a certain level , the ink-level sensor inside the secondary ink tank sends signal to the pump.

Supply ink to the print head

Please connect the print head ink outlet and inlet ink tube and connect a small length of small size ink tube with the print head ink outlet tube. Press down the positive switch to let the ink come in from the




inlet ink tube. Please lift this length of the tube when the ink is out from the ink tube. Normally, the ink will flow from the print head caused from the positive pressure

3.2.7. Start Printing

Start printing: Please print the required image according to the manual of the printing software.

3.2.8. End Printing

Finish printing: exit the printing system software, and then turn off the switch of the print head, of computer, of heating system, of power supply (close the breaker of the power supply), and also cover the electric box.




4 The way of dealing with the image for the vista software This printing system software only supplies printing process for chosen file, but not able to do image edition and pretreatment. Meanwhile, the printing system software can only identify and print 180DPI, single color 8- bitmap file. The user shall use third party software with powerful function to edit and pre-treat the image. The users are recommended to use PHOTOSHOP 6.01 version software which is produced by ADOBE Company to design the image for printer.

This manual takes the PHOTOSHOP 6.01 as an example to explain to provide the image file for the printing system software. As for the detailed usage of PHOTOSHOP, please refer to the special book for Photoshop.

4.1 Design Image

The image designer uses suitable image editing software to design wanted and needed image, and save it as the format, which can be identified, by Photoshop software.

4.2 Change the image as CMYK format

The users adopt PHOTOSHOP to open the saved image, and transfer the image by Image/Mode/ CMYK Color to CMYK format, and change the image as 8 Bits/Channel.




(Pic 5-1)

4.3 Setting Image Size

The practical size of the image file, which is set up in the computer, should be in accordance with the size of printing image, so the practical size of the image file should be adjusted. Please refer to the following picture

Note: the image designer should finish the operation of this part, so this manual wont introduce in detail. For further detailed information, please refer to the special book of PHOTOSHOP.




(Pic 5-2)

4.4 Merge Image Layers

The users may use more image layer when they design the image, and they need to use the order in picture to merge the image layer. Refer to image.

(Pic 5-3)

Click the right button on the arrowhead of the picture, it will flip the menu, please refer to the picture for this. To choose merge order to put together all image layers. If the users dont use more image




layer, the order of merge will show gray. The users can skip over this operational step, and go through to the next operational step.

4.5 Save the image file

The s e by orders of file/save after modifying the image file. user can save the image fil

The users choose the file format as TIFF, BMP, EPS or JPEG in the dialog box of save, then the name of the file can be modified.

be saved as TIFF, because the saved image file have to set up type by MAINTOP software, and then the image can be printer with the printing system software by the digital Note: the file format must

printer. However, the MAINTOP software typeset software can only identify the image file of TIFF format

(Pic 5-4)

After click save button, it will show following picture, and then its OK to click IBM PC ,and then click OK

At present, one image file has been modified, you make typesetting and output.




(Pic 5-5)




5 RIP Software PHOTOPRINT Guide 5.1 Install PHOTOPRINT

Insert PHOTOPRINT CD

PHOTOPRINT will install itself

Enter will install the procedureprocedure choicePHOTOPRINT language choiceChinese or Englishthen click the next

install enactment put in the user and passwordthen click the nextthe name of the user and the password in the dongle.

welcome click the next

license agreement choose agreeclick the next

function choicechoose the disk which has large memoryclick the next

Choose the installation type to install the software.we suggest the standard installationthen click the next.

Choose the folder, which is used for save the software. If you accept the default foldera new folder will come automatically to save the software. Click the next.

Click yes clean the presetting or click no save the primary presetting .

you must make sure the password for the dongle is rightor else you can not open the RIP softwareif do not have the dongle ,the RIP software will not work. The dongle is used to forbidden the stealing copy , whenever you use the software , you must install the dongle in your computer.

5.2 Set the printer

After finish the installationat first you must set the printer.

Production Manager the procedure run automatically then collocate the printer, choose the printer in the new menu.




In the add the equipment the manufacture is JingHengFengthe model is VISTA3306FSKONICA KM512 42PL print headorVISTA3306FNS KONICA KM512 14PL print headchoose color printer click next

installation default Vista V3306FS orVISTA3306FNSchoose install the desktop driver for printingclick the next.

Two ways of connecting with the computer

Print model

Item one Item two Item three function

Network

print

TCP/IP web site 127.0.0.1

Port No.

9100

Click to confirm, click finish

When you set this port, after the Production Manager RIP the imagethe control software for printing will be set as network printingthe inkjet printer will print directly

Print the file

When the TCP/IP web site comes, please click the cancel

Port choose FILE

This operation will be deal with and save as the default file for your computerprt file

When you set this portand after the Production Manager RIP the image, it will begin to print, while RIP while printing.

COM serial communication portthis port only supported by CNC ROUTER.

LPT parallel port is always be used for the connection of printer and the computer.

USB: The USB port supplied by the applicable equipment, and must make sure install the right driver procedure.

TCP/IP, the TCP/IP port can be adopted if the output equipment support the network connection, you should input the IP site which was distributed to you

FTP supports the network connection for the output equipment and the FTP agreement. You should input the IP sit which was distributed to you.

LPR, some network equipment can not work together with the TCP/IP, they only work together with FTP agreement, you should input the IP site which was distributed to you.

SCSI, This port can be adopted if your equipment supports the SCSI connection.




Finish add the printer as the following image

image 5-1

5.3 Add ICC align file

Click the file in the menu open menu Production Managerand click the import reset in the coming menu

Choose the FS_6C_Preset in the open, look in




(Image 5-2)

Choose the all click selectthe system will inform reset successful imported

5.4 Set the print job

Click the file in the Production Managerclick add job in the coming menuthe following image will come ,after finish the additionall of the operation can be add, delete and change the attribute production manager

image 5-3

More than one printer can be operated together, if the computer is applicable.

Double click the operation name, the image job properties, will come as the following




image 5-4

There are ten setting function in the job properties

1 Arrange

2 Item 3 Content 4 Remark

5 Media size

6 The system will alarm when media width, length excess the provisionthere must leave the blank in the front and the back , the left and the right while print

7 the media width should nearly meet the width of the machine

8 Width 9 Set the width and the length 10 /

11 Distance margin and between space 12 /

13 Workgroup





17 Operation 18 Display information 19 /

20 Path 21 Display information 22 /

23 Set 24 Display information 25 /

26 Finish out put

27 Choose delete /save 28 Choose save, it is convenient for using in the future.

29 Color manage


33 Beforehand 1,choose the beforehand usethe alignment file must be applicable to the inkif you choose this setting, the operation for the color alignment has been performed. The output file must be applicable to the ink, media, and resolution, dithering of the output equipment. When you choose the configuration file must make sure all of the configuration file must be applicable for the standard matching. Choose the ICC file from the disk.

2operation attribute; We suggest you use color alignment file

34 Beforehand example 4pass-lclm-360*360

35 The printing set 4pass

36 Media the media is optional 37 The alignment color file will be chose automatically

38 Print model The quality you want 39 The alignment color file will be chose automatically

40 Color alignment

41 Yes /no 42 The alignment color file will be chose automatically




43 Form sheet 44 Yes /no 45 The alignment color file will be chose automatically

46 Color 47 Color model: if your output equipment support multicolor model. Thus you can choose the sustaining color model.

48 /

49 superimposition 50 Yes/no 51 /

52 resolution Choose the applicable DPI for your operation. High DPI for high quality, but it need more time.

53 /

54 Note 1click the advanced in the color alignment, and click the solid color in the coming menu input ICC file the new menu will come, the setting as the following image:

55

56 57 58 59 60 image 5-5 61 Note 2

The printing label displays the correlative setting, it is up to the output equipment, the label model may be different. When you change some setting in the output equipment, it will adjust to the best position, but some manual setting.

Media choose the media type, it will come while printing.

Printing model choose the quality you want

Resolution choose the output resolution




Driver click this button to display the driver procedure dialog box, the dialog box include all the setting which correlative the output equipment. The output equipment panel can set the most setting for the driver procedure.

Liberation model choose the liberation model for output.

Screen the button is practicable, when you choose the angle screen. You can explain each frequency, angle, figure for the color belt screen.

Consistency adjustment it used for the consistency contour of output equipment.

Color alignment: check the option and make sure it is activation. If you did not check this setting, the ICC configuration file which aligned color in the internet application software will check this option, force RIP to use the ICC configuration file which exist in the operation file.

ICC input configuration file: choose ICC configuration file to change the dicey color space.

Color management: use the default color management.

ICC output configuration file: choose the ICC configuration file to match the media, fill the ink to the printer.

color space conversion mode: Choose the space conversion model, which exist in the bitmap image.

Vector color space transform model: choose space model, which was used in the vector object

Information: click this button to display the attribute dialog box of configuration; the details of the output configuration file, which has selected will be displayed. Thus you can use it to check if the selected configuration files match the media.

Color model: choose the applicable ink for the setting of printer. If the printer support manifold color model, you can choose one from them.

Separate the printing color: choose this page, and print one by one

Frontispiece: this option is optional when you choose when you check this optionit will print the image as frontispiece.

Liberation model is device model. each point for the image will be adopted by the media. Each liberation model has the advantage in the RIP speed and the quality. The best liberation model for the machine is the default.




62 Printer option: do not use this function. 63 Connection : the excess printing size should be delaminate before the output.

64 Item 65 Set content 66 Remark

Connection parts size

The width, high, blank for connection parts /

Choose the connection parts

The number, width, high for connection /

All the spell The same width, same high, fixed width, high, superposition width.

/

67 68 image 5-6 69 Label and sign

70 Item 71 Set Content 72 remark

Color Choose KCMYLCLM / width Set the width / Printing label / / Spelling the superposition line

You can set the measure between the row and the tier. Depend on the superposition, you can banish the aperture between the division at the end of combination output. The metrical superposition part will be look on as the gross superposition for the two rows and the two tiers.

/

Printing belt / /

73 Color alignment




Color belt allow you to adjust the color. Block stands for each color channel of the output equipment. Add or reduce the block to control the ink density. You can input the parameter in the compilation box.

image 5-7

74 Separate seldom use 75 Preview : preview function 76 Set the default set it as default

5.5 Send the operation

After you set the attribute in the photo print, then click send

1while set the network print, the printer will print directly. 2, when you choose the FILE to printphoto print software will save the image in the ordered file as the printing file. For example D:\rip




While printing open the control softwareclick add RIP file in the coming menu, the route is D:\ripafter the addition you can begin to print.

The details of deal with the image ,please refer to PHOTOPRIN Trip manualsoftware assistant document

5.6 Control software and the connection of PHOTOPRINT software

TCP/IP web site 127.0.0.1

Port choose FILE

5.7 The notice for PHOTOPRINT

The PHOTOPRINT software enclose the manual, and the file references. The operation notice as the following:

The image resolution, pass number must match the printing control system, while you deal with RIP, in order to get the perfect effect. The image resolution, size correspond with data size, the date size decide the operation time for

computer. After PHOTOPRINT finish RIP, the color route will become CMYK, thus the image should be

TIFF.




6 The basic operation of the printing system 6.1. The characteristic of this printing system:

Print head group: 4 or 6 KM512 print head Resolution: X point: 360DPI\240DPI\180DPI; Y point: 720DPI\540DPI\360DPI\180DPI Color: 4 or 6 color Printing mode: 1,2,3,4,6,8,12,16 pass; The input of the image: File or TCP/IP (printing while ripping) Output preview: Preview the image after changing the pm file into bmp little picture file. Any of print head can be turned on or turned off freely Automatic printing: Blank skip in X & Y direction It can print with so many pictures copied lengthways. Automatic pump: It can pump the print head automatically while printing. Flashing: It is used for protecting the print head from block while it is not working. The color bar: Used to protect the print head from concreting, monitor the state of the print head,

and set the distance & width between the image and the color bar. Adjust the data of print head alignment and media feeding size during printing. The printing direction can be set accordingly with option of unilateralist printing and

bi-directional printing, mirror image printing. Lighten the edge: Use to lighten the pass line. Automatic cleaning system Chinese and English interface Revising printing image

6.2. Printing Software Installation

6.2.1. Control Software Installation

open the CD V1806FNS /V2506FNS/V2506FS/V3306FSdifferent software for different model double click circulate Setup.exe choose install langue choose Chinese English then click ok Welcome usethen next choose a place to install the procedurethen next for example you install it in C:\Program

Files choose programmed group then next copy the filethen next Finish installation click finish A shortcut way will come on the desktop, for example JHF V3306FS V2.07cn The way of the programming will like this C:\Program Files\Digital Printers\JHF Printer V2.07




6.2.2. PCI Card Installation

Plug the PCI card into the PC, and then start the PC.

Attentions: please make sure that the right procedure is followed whenever you want to plug or pull out the PCI card, otherwise, the PCI may be damaged.

After the windows started, it find PCI card. You should search the subdirectory of PCI Card driver while install the Driver. (Or decompress PCI Card Driver)

6.3. The application for control software

6.3.1. Printer Configuration

Double click the shortcut mode JHF V3306FS V2.07Enrun the control software, please choose the printing configuration file, as the following

Choose the V3306FS180dpi/ V3306FS240dpi/ V3306FS360dpi/choice gistthe resolution must be the same as the image resolution which was deal with the RIP software and ICC.

Choose the default reposition; click ok, the carriage return to the original position. it is the printing original point The control software will be opened and enter the main interface, or choose do not anything, the carriage has no reaction, then the control software will be opened and enter the main interface.




6.3.2. Main Page

6.3.3. Main Menu

First grade menu Second Grade Menu

Function description

Open Open the wanted image directory , the image list will show the wanted image

Delete Choose the wanted job on the image list, press Del button to delete the wanted job.

Print Preview If the file under the folder is changed a little, please preview and refresh the image list

File

Exit Exit the software, it will show a diagram to ensure if the printer will return to the print head protection place.

Reposition Initialize the PCI card, the print head carriage will return to the cleaning terminal position

Print Option Open the option setting diagram and set the parameter




Basic Parameter The basic parameter is made by the engineer. The operator is not allowed to change the these basic parameter

Internet Printing

Choose this item; the printing software will follow to the printing order made by the RIP software. It can do RIP while printing. Please note that if the Ripped file sizes over 2 GB, please choose internet printing mode. Otherwise, it cannot print correctly. Additionally, please connect the computer network card and enter print mode under the print optional menu to choose the print mode.

Print Choose wanted image or double click the image list to run this function

Stop Stop printing, the print head carriage moves to cleaning terminal.

Pause Pause printing, the print head carriage moves to cleaning terminal

Continue Continue printing Cleaning Print

head Cleaning print head. Choose the details in the optional setting dialog box

Printing Test Printing test bar. Adjust the print head parameter accordingly

Flash Turn on /off pinhead flash to prevent the print head block. Choose the flash frequency in the optional setting dialog box

Cleaner Turn on/ off vacuum cleaner

Heads parametersEnter the print head voltage adjustment dialog box( for the details, please refer to the following instruction)

Status bar Show/hide status bar Refresh Refresh the image list View

Print Preview enlarge/ reduce preview file Help About Show the version code

Automatic pressure adjustment optional (choose the voltage, it adjust automatically)

When the printer is on, enter this dialog and press Read switch and download 4 and 6 print head voltage parameter.




Note: please dont press Write first, otherwise it will write wrong parameter into the print head transforming board.

Only the HV offset row parameter is revisable. The PH 1 column matches print head K, the PH2 column matches print head C, the PH3 column matches print head M, the PH4 column matches print head Y, the PH5 column matches print head Lc, and the PH6 column matches print head Lm. The value adjustable scope for the HV offset row is -127-127. If set this parameter as Zero, it means that voltage will not do excursion.. If choose permit the print head adjust electric pressure, it will adjust automatically according to the temperature change. If dont choose permit the print head adjust electric pressure, the print head voltage will not change.

Note: When press down Read or Write switch and turn on printer, the software system will automatically return to the automatically adjusting voltage status except that you dont choose the permit the print head voltage adjust function.

The voltage is the power of the ink jetting, the temperature and the humidity will affect the ink jetting serious. The lower voltage can cause the ink jump, the higher voltage can cause the ink break. You should adjust the voltage depend on the ink

Adjust the voltage to make sure the voltage is above 15, when you adjust the voltage you should put in the parameter between -5----+5 in the voltage excursion

Adjust the voltage excursion parameter according to the temperature/ voltage value listed on above-listed table to make the head voltage to close the actual output voltage. When the value is close




to the actual output voltage, normally, it can print formally. If it is still lack of lack of ink, please low the voltage until the printer can print normally.

6.3.4. Keyboard Shortcuts

To efficient the operatin, we offered keyboard shortcuts:

Ctrl+Home Initialization

Ctrl+End Cleaning

Ctrl+Pause Pause

Ctrl+ Move to left

Ctrl+ Move to Right

Ctrl+ Media back

Ctrl+ Media forward

6.3.5. Default Parameter, Shortcut icon

In order to set the regular setting easily, there is parameter column under the tool bar.

Path: the path for the wanted job

Pass: printing mode at 1,2,3,4,6,8,12,16 pass optional

Printhead carriage speed

Quantity : Quantity for each job




Printing position: the distance between the start print position and the cleaning terminal. Unit is mm.

Blank edge: the distance between the left edge of the material and the cleaning terminal. The unit is mm.

Movement value: the distance for the movement of the printhead carriage and the media when enter Ctrl+ direction

Testing: Printing testing bar to adjust the printhead excursion parameter

Item Aim Note Status Check the ink jetting, ink break, print head block Alignment Color alignment the adjustment for bi-direction color

alignment

Stepping offset Repair adjustment should happen together each circulate of stepping motor

Completely jetting 4 color 100% jetting need to check the ink capacity Testing output the square meter per hour

Test the print head

image 6-4

You can see each print head block from the following image.

The array of the print heads

Adjust the Excursion value of each print heads according to the above drawing, which should be as the first black print heads on the left side .

Step Excursion




This drawing is for testing the Excursion value for different pass printing . after adjusting the step Excursion and make it equal with the correct line number ,the printer can accurate print .

Full Printing

You can print mixed color square with 100% density ink quantity. By this test you can check the ink saturation, and you can cancel one or more colors to test one or mixed colors full printing effect.

6.3.6. Printing Mode

Pass 1,2,3,4,6,8,12,16 pass optional Carriage Speed High, middle and low speed optional

Media-feeding speed High, middle and low speed optional Quantity Quantity for each printing job Horizontal mirror It is used for the double-side mirror image

Vertical mirror Vertical mirror printing of each pass Blank-skip Skip the blank area of the printing job

Print mode

Printing direction This system prints from left to right.




Uni- direction Uni-direction printing Setting the color bar besides the printing job to prevent print head from block during printing and follow the heads condition Color bar/ No color bar Turn on/ off the color bar

Distance Distance between the color bar and printing job The unit is one jet dot distance.

Width Two values. The former is separate color bar width; the latter is mixed color bar width. The unit is one jet dot distance.

Color bar

Position The color bar is put at the right side of the image or the left side of the image. The unit is one jet dot distance.

Automatically vacuum suction during printing Automatic cleaning/ Non automatic cleaning

Turn on/ off the color bar

Frequency Cleaning one time every xx pass

Times The times of the print head carriage moves through each cleaning

Mode Cleaner: use the vacuum cleaning to clean; Flash: Flash cleaning the print head

Automatic cleaning

Flash frequency 0~16 flash frequency. Normally choose 8 or 16. Printing position The position which the printer start printing from.

Start point The width between the start point and the edge of the media

Width Material Width (unit: mm)

Material setting

Blank edge The distance between the left edge of the material and cleaning terminal ( Unit: mm)




6.3.7. The array of print heads

Print head Quantity

The quantity of the print heads which is used to print

Colors 4color, 6color Nozzles Quantity

The quantity of the nozzle for each print head Print Heads Group

Print Heads Resolution

The physical resolution of each print head

Step Excursion The step excursion is different at different pass (unit :1/4 printing point distance)

Acceleration Length During printing the acceleration/deceleration speed of the carriage when it moves through the printed outs two sides. (unit: one print pint distance)

Color Excursion Each print head has three parameter as the excursion value (unit: one printing point distance)

Moving to left When the printer prints from right left, the excursion will be increased when you increased the value, and will be decreased if decreased the value.




Moving to right When the printer prints from left to right, the excursion will be increased when you increased the value, and will be decreased if decreased the value.

Vertical movement excursion

the Excursion value for each print heads vertical movement (this value cant be minus)

Attention : If you need replace the Setup.ini option ,please restart the printer software

6.3.8. Automatic Vacuum cleaning

Open the procedure file C:\Program Files\Digital Printers\JHF Printer V2.07/setup-V3306FS-240/180/360dpi.ini

uiCleaning=0the carriage, suck ink for the left

uiCleaningWidth=2700the width of carriage move

6.3.9. STATUS BAR

POS:xxxxx/xxxx: the absolute position of carriage on raster (unit: the printing point distance) the relative position of the carriage on the raster (unit :mm)

PSS:xx/xx/xxxxx: printed out finished lines/ print out total lines / printing status

STS:xxxxx: on/off state ( the status is 1/0): 0/0/left limited switch/right limited switch/l

Basic parameter setting:

Put in the engineer passwordplease refer to JHF company

After entered, the following parameter setting will come

print head arrangement

item Purpose remark Print head channel

Set the sequence number of print head for the color board.

Color channel

Set the sequence number of ink for the color board.


Beijing Innovation

www.jhfvista.com

Movement system setting

Item purpose Remark X reposition

speed

The speed of the carriage return to the original

slow/middle/fast the carriage speed while printing X movement Click movement, the carriage move, the raster

transfer the signal, click calculate, the system will account the step parameter automatically.

Y movement Click movement, the stepping driver move, measure the moved distance. Input the parameter you measured, the system will account the stepping parameter automatically.

6.4. Fiber Installation:

Two fibers A & B usport of fiber for eachplug into Tx, then thright port.

Attentions: the

be damaged in the rwant to change the pB Technology Co.,Ltd. PAGE 60

TEL86 10 62950101 FAX86 10 82410746

ed for connect the control card of the print head and PCI c control card. There is Tx and Rx stick on the port. Whil

e other one should plug into Rx. Please kindly notice that y

fiber shouldnt be curved or tied less than 90 degree. Oth

etrieval condition. Even lead to its disability to transfer thoint of the fiber, then 3cm Turning radius should be kept. ABAard, as there is connect e one end of the fiber ou should point to the

erwise, the may e data directly. If you




7 Daily maintenance and repair JHF-Vista digital inkjet printer is a high-resolution, high-performance electronic production with professional output of image which requires maintenance and repairs strictly in order to keep the system in normal and stable order to insure output image with high resolution

7.1. Operating environment request

Power supply: single-phase 220v 50Hz; Power on 24hrs/ day

Operating temperature: 20-28

Relative humidity: 40-60%

Note: the working environment will affect the ink and then affect the output of printe

7.2 Operation & Maintenance Requirement

The task of the operation and maintenance need to be operated and maintained with professional operator or the operator who got training from our Company and to be certified qualified. The user must do strictly according to this manual.

1) Wear anti-static device when touching circuits, electric parts, cable, and print heads.

2) Strictly prohibit pull out or insert any plugs, circuits, and cables with electricity.

3) Strictly prohibit measure all kinds of electric parts of appliance with electricity.

4) When contacting the ink you should try to wear protect-eyepiece to avoid the ink entering

the eyes. If it is entering the eyes, you should wash with a plenty of clear water. And please go to see a doctor, if necessary.

5) Shake the ink evenly twice every day.

6Check distance switch and home position switch before turning on the printer every time.




The distance-switch is a limit protection for the print head movement, it gives stop instruction to the print heads by the electronic device. Please check it if these limit-switches work before running the printer every time. In case, the limit-switched dont work well, which will affects the output of printing, making output in misalignment. If so, please follow the following steps:

Please move the carriage from left to right after turn on the printer. When touching lightly the right limit switch, the print head carriage stops, which means that the right limit-switch works well; if not, please click the Stop button on tool bar under the printing software and stop the carriage, then check the circuit and shoot the trouble.

Please move the carriage from right to left. When touching lightly the left limit switch, the print head carriage stops, which means that the left limit-switch works well; if not, please click the Stop button on tool bar under the printing software and stop the carriage, then check the circuit and make the trouble-shooting.

Please move the carriage from right to left. When touching lightly the home position switch, the print head carriage stops, which means that the home position-switch works well; if not, please click the Stop button on tool bar under the printing software and stop the carriage, then check the circuit and make the trouble-shooting.

7Before printing and after printing, please clean the print head and make the print head in good condition.

Please use special cloth or paper with cleaning solution on it to wipe the print head when cleaning the print head. It is suggested to do like this every day before printing, if necessary repeat this work between two printing jobs, which will ensure the output in perfect position.

Print head is very important device, the following is cleaning requirement:

Please wear gloves, glasses and protective cloth to protect the operation. Please use the professional duster cloth, wipe paper to clean print heads Please use professional cleaning solvent or solution recommended by us to clean the print head

and its surrounding; Sucking print heads one by one to take the solvent and ink remained on the print heads surface by

the vacuum cleaner; Please dont scrape the surface of the print head when sucking; After cleaning and sucking please test the print heads. If they are working well or not. Automatic suction is critical to maintain print heads. To keep the print heads jetting please wipe

off the remained ink on the print heads surface. Please lacquer the vacuum surface black to prevent the photoelectric cell running. Please clean the print head lightly in uni-direction when cleaning the print head; Please suck the print heads surface completely by vacuum after clean the print head by solvent.

8Turn on and off the machine strictly in order.




9Please change the filter every two months; if the filter is clogged, please replace immediately.

Drain the ink from the ink tube Disconnect the ink tubes in the two ends of the filter, replace the filter. Reconnect the ink tube and check if they are connected tightly and safely; Make sure if the direction of the filter is in same direction as the direction of supplying ink

Note: The filter is a single direction appliance; when connecting, please make sure the flow of

the ink is in same direction as the filter.

10Change the ink tube one time every year

We suggest to replace the ink tube every year, if any ink tubes broke unexpected, please replace immediately.

Exhaust all inks in the ink tube after turn off the printer and computer; Clean new ink tubes one time by special cleaning solution to get rid of impurity inside the tube

and dry the cleaning solution inside new ink tube completely;

11Cleaning the vacuum cleaner

The flexible tube with the vacuum cleaner will diminish after a long time, which will deduct air power from the vacuum cleaner. In this case, changing a new flexible tube with the cleaner is necessary or clean the flexible tube with a few of cleaning solution.

7.3. Print head Maintenance

7.3.1. Print head maintenance reason

The importance for print head maintenance as following:

The life of print head

The stable performance of print head

The quality of printing

The usage maintenance of print head will effect the motion of print head in all the system directly . The purpose of maintenance is to keep the base case of print head working: clean the ink on the nozzle and the waste ,drive the air in the nozzle tube. The standard of the environment above according to the environment of setting the printer , the work loading of the system , the type of ink ,the printing material , and the tactic for maintenance of print head.




7.3.2. The tactic of maintenance

AMaintenance during printer operation

This maintenance is carried out during printer running. It is an automatic function which is executed at specified time during printing, it support a reliable and continuous printing for the printing orders.

B Maintenance for short term

Maintenance for short term should be need when the machine is in work-off for a while. For example, it should be required at the very beginning of printing or after finishing the work. Suggestion is that the maintenance should be an autoimmunization system in order to operate repeatedly and unfailingly.

CMaintenance for long term

Maintenance for long term should be needed when work is finished all day or the whole system be closed absolutely. All in all, the long-term maintenance is carried out with the state of work-off.

7.3.3. Print Head Maintenance

You can adopt one or mixed the follow daily maintenance ways:

APress and washing

Press and washing ways include two important functions:

To clean the air and contamination in the spout.

To clean the contamination in the nozzle.

Such of way could increase the heat of ink supply ,pressing the ink until gush out the hole ink of nozzle.

If the temperature of the print head is different from the environment around, pressing and cleaning can lead the temperature become low, then affect the function of the print head. so before restart, you should do a warm up. one of these ways to avoid this warm up is heating the ink before it come into the print head, then the temperature Is suit for the print head.

BVacuum clea

Documents

VISTA-KM512-PCI-DC-English Manual V.0711.pdf