2
x1 — Top Connector x2 — Top Pole x2 — Center Pole x2 — Bottom Pole x2 — Base Stand (Left + Right) x1 — Base Bracket x4 — Long Bolts x8 — Arms x6 — Short Bolts x2 — Extra Long Bolts x2 — Nuts (10mm) x2 — Washers x4 — O Ring x1 — Basket Parts A B C D E F G H I J K K L M N Assembly instructions HDRS6801 WARNING DO NOT EXCEED MAXIMUM TOTAL WEIGHT LIMIT OF 160 LBS (70 Kgs) MAX LOAD PER HOOK: 35 LBS (15.9 kgs) / MAX WEIGHT PER BIKE: 40LBS (18.2 kgs) LOAD HEAVIER BIKES, INCLUDING E-BIKES, ON LOWER TIER. C H D A K F E L I G B Assembly Video Visit designbydelta.com/downloads Scan with your smartphone camera to view C H D A F F M F N E I I J G Tool(s) Required Phillips Head Screwdriver Adjustable Wrench (or 10mm) Free-Standing 4 Bike Rack with Basket

Visit designbydelta.com/downloads Free-Standing 4 Bike

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

x1 — Top Connector

x2 — Top Pole

x2 — Center Pole

x2 — Bottom Pole

x2 — Base Stand (Left + Right)

x1 — Base Bracket

x4 — Long Bolts

x8 — Arms

x6 — Short Bolts

x2 — Extra Long Bolts

x2 — Nuts (10mm)

x2 — Washers

x4 — O Ring

x1 — Basket

PartsA

B

C

D

E

F

G

H

I

J

KK

L

M

N

Assembly instructions HDRS6801

WARNINGDO NOT EXCEED MAXIMUM TOTAL WEIGHT LIMIT OF 160 LBS (70 Kgs)MAX LOAD PER HOOK: 35 LBS (15.9 kgs) / MAX WEIGHT PER BIKE: 40LBS (18.2 kgs)LOAD HEAVIER BIKES, INCLUDING E-BIKES, ON LOWER TIER.

C

H

D

A

K

FE

L

I

G

B

Assembly VideoVisit designbydelta.com/downloadsScan with your smartphone camera to view

C

H

D

A

FFMFN E

I

IJ

G

Tool(s) RequiredPhillips HeadScrewdriver

Adjustable Wrench(or 10mm)

Free-Standing 4 Bike Rackwith Basket

1Connect base bracket (F), bottom poles (D) and base stand (E)as shown using long bolts (G, J) Nuts (K) and Washers (L).Do not tighten bolts until rack is fully assembled and tubes areproperly aligned. Fully assemble base before continuing.

3

5

Connect toppoles (B) to centerpoles (C), securewith short bolts (I).Connect topconnector (A) to toppoles (B) usinglong bolts (G).

Use short bolt (I) toattach basket (N) bypositioning in line withdesired height holeon the inside of thecenter pole (C)(FIGURE 1)

4

2Connect center poles (C) to bottom poles (D),secure with short bolts (I).

Adjust position of arms beforeplacing bike on stand.

Tighten all bolts, usingthe wrench to hold nutswhere needed.O Rings (M) can be usedto slide over base legswhere needed on uneven�oor surfaces

IMPORTANT / SAFETY

Delta Cycle Corporation36 York Avenue, Randolph, MA 02368 USA800-474-6615 / www.designbydelta.com

© Copyright 2020

After rack is assembled Arms should be placed at desired height - two perbike (front and rear).

Front side of rack features thelonger section of the base foot

Need help? Please do not return to store.For immediate response email [email protected]

Always load bikes on the arms of the bottom,front side of the rack �rst to maintain stability.

Remove bikes from the top �rst.

Store e-bikes and other heavybikes on lower arms only.

Do not allow children to play or hang from rack.

FIGURE 2

FIGURE 1