Upload
hoangthien
View
222
Download
1
Embed Size (px)
Citation preview
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
®
GPM .06 to 75③ (Nominal Rating)
Viking® Mag Drive is designed to provide positive- displacement pumping capability in those situations that require the highest assurance of liquid containment. Viking Mag Drive provides for the safe, trouble-free transfer of hazardous, EPA-regulated fluids without electronic monitoring as required with mechanical face-type shaft seals. Hard-to-seal liquids are also easily handled with the Viking Mag Drive which eliminates the high cost of mechanical seal replacement and repair. A variety of coupling sizes are available for flow requirements to 75 GPM. The torque-carrying ability of high-strength magnets allows pumps to be coupled with gear reducers for slow-speed handling of viscous liquids. The self-priming positive-displacement pumping principle provides low-shear, nonpulsating flow. Internal gear pumps are available in stainless steel, steel, and cast iron construction. External gear pumps are available in cast iron or ductile iron construction with heat- treated steel shafts and gears.① See following pages and performance curves for specific recommendations.
Certain models have lower limitations.② Optional samarium cobalt magnets are used at temperatures over 225°F.③ Nominal capacities based on handling thin liquids at low pressures.
Kalrez®- Registered trademark of DuPont Performance Elastomers.Viton®- Registered trademark of DuPont Performance Elastomers.Viking® and Viking Mag Drive®- Registered trademarks of Viking Pump, Inc.
① Differential Pressures
To 34 BARTo 500 PSI External Gear
To 8.5 BARTo 125 PSI Internal Gear
② Temperature Range
-50°C. to +260°C.-60°F. to +500°F.
① Viscosity Range
1.0 cSt. to 55,000 cSt.28 SSU to 250,000 SSU
FEATURES
INTERNAL GEAR AND SPUR GEAR PUMPSWITH MAGNETIC DRIVE
TemperatureSensor
CasingBushing
BalancePlate Casing
Head
Idler Pin
Head GasketOuter Magnet Assembly
Bearing Carrier Assembly Canister
Shaft
Bracket
Inner Magnet AssemblyCanister O-Ring
RotorIdler
Pressure Relief Valve
SERIES 897 PumpsCutaway View
“HL” size shown
INTERNAL GEARViking internal gear Mag Drive pumps are available in stainless steel, steel, or cast iron construction with capacities up to 75 GPM. With only two moving parts Viking Mag Drive and Viking’s gear-within-a-gear principle provides low-shear pumping.
MAGNETIC COUPLINGViking Mag Drive magnetically couples the pump to the driver. Magnetic force passing through a stainless steel canister is used to drive the inner coupling, eliminating the need for shaft seals.
EXTERNAL SPUR GEARViking external spur gear Mag Drive pumps are available in cast iron construction in capacities from .06 to 32 GPM. The Viking Mag Drive can be used in conjunction with a Viking Spur Gear Pump for metering or low-capacity transfer of toxic or expensive liquids.
Section 680Page 680.�Issue D
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
®
PumpConstruction ① O-Ring Casing Head Rotor Idler
BalancePlate
RotorShaft
IdlerPin
IdlerBushing
InternalPressure Relief
ValveStainless
Steel PTFE StainlessSteel
StainlessSteel
StainlessSteel ③ PPS PPS Coated
Stainless SteelCoated
Stainless SteelCarbonGraphite
StainlessSteel
Steel Buna-N Steel Steel ② DuctileIron ③ PPS PPS Steel Steel Carbon
GraphiteSteel
Externals
Cast Iron Buna-N Iron Iron ② DuctileIron ③ PPS PPS Steel Steel Carbon
Graphite Iron
CONSTRUCTION—SERIES 897 (STAINLESS STEEL)—SERIES 893 (STEEL) AND SERIES 895 (CAST IRON)
① Buna-N, Viton®, Neoprene, PTFE, or Kalrez® O-Rings available.② Standard construction includes iron rotor for “GG” and “HJ” sizes: ductile iron rotor for
“HL” through “AL” sizes. When steel-fitted construction is required, hardened steel rotor will be provided on “GG” through “HJ” sizes.
③ Standard Material is Polyphenylene Sulfide with composite material. Recommend using metal idler above 10,000 SSU.
④ See pages 680.21 through 680.44 for specific coupling recommendation on other pressures and viscosities. See page 20 for “Selecting the correct Mag Drive coupling.”
⑤ Higher temperatures can be handled with Samarium Cobalt magnets. See page 20 for torque and temperature limits.
⑥ “AS” and “AK” Series 895 have 2½” NPT tapped ports.⑦ For bearing carrier weights add 8 lbs (2 KG) for “MD-A” size, add 17 lbs (4 KG) for “MD-B” size.
ModelNumbers
Materialsof
Construction
PortSize
NominalPumpRating
④MagneticCoupling
Availability⑤MaximumTemperature
(Standard Construction)
MaximumHydrostatic
Pressure
ApproximatePump Shipping
WeightWith Valve
(Less Power)
⑦ Approximate Coupling Only
Shipping Weight (ready to accept but less power)
Series
Torque
Inches GPM m³/h RPM Ft-Lbs NmDegrees
F.Degrees
C. PSIG bar Lbs. KG Lbs. KGGG-897 Stainless Steel
110 2.3 1800
MD-A4
9
5.4
12.2225 93 400 28 22 10
31 14
GG-893 Steel7 1.6 1200GG-895 Cast Iron
HJ-897 Stainless Steel
1½20 4.5 1800
MD-A
MD-B
4
9
15
40
5.4
12.2
20.3
54
225 93 400 28 30 14HJ-893 Steel13 3.0 1200HJ-895 Cast Iron
HL-897 Stainless Steel
1½30 6.8 1800
225 93 400 28 30 14
71 32
HL-893 Steel20 4.5 1200HL-895 Cast Iron
AS-897 Stainless Steel⑥ 3 35 8.0 1200
MD-B
MD-C
15
40
80
20.3
54
108
225 93 400 28 78 35AS-893 SteelAS-895 Cast IronAK-897 Stainless Steel
⑥ 3 50 11 1200 225 93 400 28 78 35AK-893 SteelAK-895 Cast IronAL-897 Stainless Steel
3 75 17 1200 225 93 400 28 78 35 95 43AL-893 SteelAL-895 Cast Iron
SPECIFICATIONS — SERIES 897, 893 AND 895
Dimensions for Internal Gear Mag Drive Pumps - See Pages 680.4 through 680.12.Performance Data for Internal Gear Mag Drive Pumps - See Pages 680.21 through 680.44.
SERIES 895 PumpsMD-B15M, motor direct connected to bracket and pump with tapped ports.
SERIES 895 PumpsMD-B15B, bearing carrier,
footed bracket, andmounted pump with
tapped ports.
SERIES 897, 893 AND 895INTERNAL GEARSTAINLESS STEEL, STEEL AND CAST IRON WITH MAGNETIC DRIVE
Section 680Page 680.�Issue E
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
®
① Buna-N, Viton®, Neoprene, PTFE, or Kalrez® O-Rings available.② Standard construction includes iron rotor for “GG” and “HJ” sizes: ductile iron rotor for
“HL” through “AL” sizes. When steel-fitted construction is required, hardened steel rotor will be provided on “GG” through “HJ” sizes.
③ Standard Material is Polyphenylene Sulfide with composite material. Recommend using metal idler above 10,000 SSU.
④ See pages 680.21 through 680.44 for specific coupling recommendation on other pressures and viscosities. See page 20 for “Selecting the correct Mag Drive coupling.”
⑤ Higher temperatures can be handled with Samarium Cobalt magnets. See page 20 for torque and temperature limits.
⑥ “AS” and “AK” Series 895 have 2½” NPT tapped ports.⑦ For bearing carrier weights add 8 lbs (2 KG) for “MD-A” size, add 17 lbs (4 KG) for “MD-B” size.
① Viton®, Neoprene, PTFE, or Kalrez® available.② See page 20 for “Selecting the correct Mag Drive coupling.”
③ Higher temperatures can be handled with Samarium Cobalt magnets. See page 20 for torque and temperature limits.
ModelNumbers
PortSize
(NPT)
NominalPumpRating
② MagneticCoupling
Availability③ MaximumTemperature
(StandardConstruction)
MaximumHydrostatic
Pressure
ApproximateShipping Weight
With Valve(Less Power)
Approximate Coupling Only
Shipping Weight (ready to accept but
less power)
Series
Torque
Inches GPM m³/h RPM Ft-Lbs NmDegrees
F.Degrees
C. PSIG bar Lbs KG Lbs KGSG-80417 ⅜ 0.06 0.013 1800
MD-A
4
9
5.4
12.2 225 107
1000 69
6 2.7
31 14
SG-80418 ⅜ 0.14 0.031 1800SG-80425 ⅜ 0.18 0.041 1800SG-80435 ⅜ 0.27 0.061 1800SG-80450 ⅜ 0.36 0.082 1800
7 3.2SG-80470 ⅜ 0.50 0.11 1800SG-80518 SGN-80518 ½ 0.70 0.16 1800
6 2.7SG-80525 SGN-80525 ½ 1.0 0.23 1800SG-80535 SGN-80535 ½ 1.4 0.32 1800SG-80550 SGN-80550 ½ 2.0 0.45 1800
7 3.2SG-80570 SGN-80570 ½ 2.8 0.63 1800SG-80510 SGN-80510 ½ 4.0 0.91 1800 8 3.6SG-80514 SGN-80514 ¾ 5.6 1.27 1800 9 4.1SG-80519 SGN-80519 ¾ 7.6 1.72 1800 10 4.5SG-80528 SGN-80528 ¾ 11.2 2.54 1800 11 5.0SG-80741 SGN-80741 1 4.0 0.91 1800
MD-A
MD-B
4
9
15
40
5.4
12.2
20.3
54.0
1000
400
69
28
15 6.8SG 80758 SGN 80758 1 5.6 1.27 1800 17 7.7SG-80782 SGN-80782 1 8.0 1.81 1800 18 8.2SG-80711 SGN-80711 1 11.2 2.54 1800 19 8.6SG-80716 SGN-80716 1 16.0 3.63 1800 20 9.1
71 32SG-80722 SGN-80722 1½ x 1¼ 22.0 5.00 1800 41 18.6SG-80732 SGN-80732 1½ x 1¼ 32.0 7.27 1800 43 19.5
SPECIFICATIONS — SERIES SG-804, SG-805, SG-807—CAST IRON - SGN-805, SGN-807—DUCTILE IRON
STAINLESS STEEL, STEEL AND CAST IRON WITH MAGNETIC DRIVE
CONSTRUCTION
Model Head, Casing, Separation
Plate & BracketGears
Heat-TreatedShafts
Case-HardenedBearings ①
O-RingsStandard OptionsSG-804, SG-805,
SG-807 Iron Steel Steel Carbon Graphite Needle Bearingsor Bronze Buna-N
SGN-805, SGN-807 Ductile Iron Steel Steel Carbon Graphite Needle Bearings or Bronze Buna-N
SERIES 804, 805, AND 807EXTERNAL SPUR GEARCAST IRON WITH MAGNETIC DRIVE
Dimensions for External Gear Mag Drive Pumps - See Pages 680.13 through 680.19.Performance Data for External Gear Mag Drive Pumps - See Pages 341.21 through 341.66.
SERIES SG-805 PumpsWith MD-A Mag Drive Coupling.
Section 680Page 680.3Issue F
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.4Issue C
®
SERIES 893 AND 895STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
For specifications, see page 680.2.
DIMENSIONS–SERIES 893STEEL UNMOUNTED PUMPS“GG”–“HJ”–“HL” SIZES
For specifications, see page 680.2.
DIMENSIONS–SERIES 895CAST IRON UNMOUNTED PUMPS“GG”–“HJ”–“HL” SIZES
MODEL NO.(in)A B C E G H
GG-893 1in 4.00 4.29 1.12 0.62 0.50
mm 102 108 29 16 13
HJ-893HL-893 1½
in 4.00 5.44 1.50 0.62 0.50mm 102 138 38 16 13
MODEL NO.(in)A B C E G H
GG-895 1in 2.75 4.29 1.12 0.62 0.50
mm 70 108 29 16 13
HJ-895HL-895 1½
in 3.75 5.44 1.50 0.62 0.50mm 95 138 38 16 13
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.5Issue C
®
SERIES 897 AND 895STAINLESS STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
MODEL NO.(in)A B C E G H
GG-897 1in 4.00 4.29 1.12 0.62 0.50
mm 102 108 29 16 13
HJ-897HL-897 1½
in 4.00 5.44 1.50 0.62 0.50mm 102 138 38 16 13
For specifications, see page 680.2.
DIMENSIONS–SERIES 897STAINLESS STEEL UNMOUNTED PUMPS“GG”–“HJ”–“HL” SIZES
MODEL NO.(in)A B C E G H J K
GG-895-MD-A_B 1in 2.75 4.29 1.12 0.62 0.50 4.35 15.30
mm 70 108 29 16 13 123 389
HJ-895-MD-A_B HL-895-MD-A_B 1½
in 3.75 5.44 1.50 0.62 0.50 5.50 16.75mm 95 138 38 16 13 140 425
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-A–“B” DRIVE)“GG”–“HJ”–“HL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.6Issue C
®
SERIES 895CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-B–“B” DRIVE)“HJ”–“HL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
MODEL NO.(in)A B C D E G H J K L M N P R T W
GG-895-MD-A_M 1in 2.75 4.29 3.50 1.12 0.62 0.50 4.85 4.75 3.50 0.62 0.50 6.72 2.75 5.25 0.34
mm 70 108 89 29 16 13 123 121 89 16 16 171 70 133 9
HJ-895-MD-A_MHL-895-MD-A_M
1½in 3.75 5.44 3.50 1.50 0.62 0.50 5.50 4.75 3.50 0.62 0.50 6.72 2.75 5.25 0.34
mm 95 138 159 38 16 13 140 121 89 16 13 171 70 133 9
HJ-895-MD-B_MHL-895-MD-B_M
1½in 3.75 5.44 6.25 1.50 0.62 0.75 6.63 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56
mm 95 138 159 38 16 13 164 165 127 19 13 178 70 210 14
For specifications, see page 680.4.
DIMENSIONS–SERIES 895(MD-A AND MD-B–“M” DRIVE)“GG”–“HJ”–“HL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.7Issue C
®
SERIES 895CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
SERIES 893 AND 895STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
For specifications, see page 680.2.
DIMENSIONS–SERIES 893STEEL UNMOUNTEDPUMPS“AS”–“AK”–“AL” SIZES
For specifications, see page 680.2.
DIMENSIONS–SERIES 895CAST IRON UNMOUNTED PUMPS“AS”–“AK”–“AL” SIZES
MODEL NO.(in)A B C E F G H
AS-893AK-893 3
in 6.00 7.50 2.00 7.00 1.12 0.75mm 152 190 51 178 29 19
AL-893 3in 6.00 7.25 2.50 7.00 1.12 0.75
mm 152 184 63 178 29 19
MODEL NO.(in)A B C E F G H
AS-895AK-895 2½
in 5.00 7.50 2.00 7.00 1.12 0.75mm 127 190 51 178 29 19
AL-895 3in 5.00 7.25 2.50 7.00 1.12 0.75
mm 127 184 63 178 29 19
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.8Issue C
®
SERIES 897 AND 895STAINLESS STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
For specifications, see page 680.2.
DIMENSIONS–SERIES 897STAINLESS STEEL UNMOUNTED PUMPS“AS”–“AK”–“AL” SIZES
MODEL NO.(in)A B C E F G H
AS-897AK-897 3
in 6.00 7.50 2.00 7.00 1.12 0.75mm 152 190 51 178 29 19
AL-897 3in 6.00 7.25 2.50 7.00 1.12 0.75
mm 152 184 63 178 29 19
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-B– “B” DRIVE)“AS”–“AK”–“AL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
MODEL NO.(in)A B C E F G H J K
AS-895-MD-B_BAK-895-MD-B_B 2½
in 5.00 7.50 2.00 7.00 1.12 0.75 8.69 23.53mm 127 190 51 178 29 19 221 598
AL-895-MD-B_B 3in 5.00 7.25 2.50 7.00 1.12 0.75 8.44 23.78
mm 127 184 63 178 29 19 14 604
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.9Issue C
®
MODEL NO.(in)A B C D E F G H J K L M N P R T W
AS-895-MD-B_M AK-895-MD-B_M 2½
in 5.00 7.50 6.25 2.00 7.00 1.12 0.75 8.69 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56mm 127 190 159 51 178 29 19 221 165 127 19 13 178 70 214 14
AL-895-MD-B_M 3in 5.00 7.25 6.25 2.50 7.00 1.12 0.75 8.44 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56
mm 127 184 159 63 178 29 19 214 165 127 19 13 178 70 214 14
SERIES 895CAST IRON CONSTRUCTIONPERFORMANCE CURVE NOTES
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-C80 “B” DRIVE)“AS”–“AK”–“AL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-B–“M” DRIVE)“AS”–“AK”–“AL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
MODEL NO.(in)A B C E F G H J K
AS-895-MD-C80-BAK-895-MD-C80-B 2½
in 5.00 7.50 2.00 7.00 1.12 0.75 8.25 22.83mm 127 190 51 178 29 19 210 580
AL-895-MD-C80-B 3in 5.00 7.25 2.50 7.00 1.12 0.75 8.00 23.08
mm 127 184 63 178 29 19 203 586
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.�0Issue C
®
SERIES 895CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
MODEL NO.(in)A B C L M
GG-895-MD-A_R 1in 2.75 8.12 3.73 4.29
mm 70 206 95 108
HJ-895-MD-A_RHL-895-MD-A_R 1½
in 3.75 8.12 4.88 5.44mm 95 206 124 138
HJ-895-MD-B_RHL-895-MD-B_R 1½
in 3.75 10.87 6.00 5.44mm 95 276 152 138
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-A– AND MD-B–“R” DRIVE)“GG”–“HJ”–“HL” SIZES“A” SIZE REDUCER UNITS
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.��Issue C
®
SERIES 895CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-B–“R” DRIVE)“AS”–“AK”–“AL” SIZES“A” SIZE REDUCER UNITS
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-B–“R” DRIVE)“AS”–“AK”–“AL” SIZES“B” SIZE REDUCER UNITS
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.��Issue C
®
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-C80 “R” DRIVE)“AS”–“AK”–“AL” SIZES“B” SIZE REDUCER UNITS
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
For specifications, see page 680.2.
DIMENSIONS–SERIES 895(MD-C80 “D” DRIVE)“AS”–“AK”–“AL” SIZES
① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.
SERIES 895CAST IRON CONSTRUCTIONPERFORMANCE CURVE NOTES
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.�3Issue C
®
PERFORMANCE CURVE NOTES
SERIES SG-804 AND SG-805CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
For specifications, see page 680.3.
DIMENSIONS–SERIES SG-804, SG-805 AND SGN-805(MD-A–“B” DRIVE)
MODEL NO.(in)A
WITH R/V LESS R/V
DDB C E B C E
SG-80417MD-A_B ⅜in 2.02 13.71 2.08 2.21 12.71 2.27 0.31
mm 51 348 53 56 323 58 8
SG-80418MD-A_B ⅜in 2.02 13.71 2.08 2.21 12.71 2.27 0.31
mm 51 348 53 56 323 58 8
SG-80425MD-A_B ⅜in 2.09 13.78 2.15 2.28 12.78 2.34 0.31
mm 53 350 55 58 325 59 8
SG-80435MD-A_B ⅜in 2.19 13.88 2.25 2.38 12.88 2.44 0.31
mm 56 352 57 60 327 62 8
SG-80450MD-A_B ⅜in 2.34 14.03 2.40 2.53 13.03 2.59 0.31
mm 59 356 61 64 331 66 8
SG-80470MD-A_B ⅜in 2.54 14.23 2.60 2.73 13.23 2.79 0.31
mm 65 361 66 69 336 71 8
SG-80518MD-A_B SGN-80518MD-A_B ½
in 2.02 13.71 2.08 2.21 12.71 2.27 0.31
mm 51 348 53 56 323 58 8
SG-80525MD-A_B SGN-80525MD-A_B ½
in 2.09 13.78 2.15 2.28 12.78 2.34 0.31
mm 53 350 55 58 325 59 8
SG-80535MD-A_B SGN-80535MD-A_B ½
in 2.19 13.88 2.25 2.38 12.88 2.44 0.31
mm 56 352 57 60 327 62 8
SG-80550MD-A_BSGN-80550MD-A_B ½
in 2.34 14.03 2.40 2.53 13.03 2.59 0.31
mm 59 356 61 64 331 66 8
SG-80570MD-A_B SGN-80570MD-A_B ½
in 2.54 14.23 2.60 2.73 13.23 2.79 0.31
mm 65 361 66 69 336 71 8
SG-80510MD-A_B SGN-80510MD-A_B ½
in 1.84 14.53 1.90 1.84 13.53 1.90 0.31
mm 47 369 48 47 344 48 8
SG-80514MD-A_B SGN-80514MD-A_B ¾
in 2.04 14.93 2.10 2.04 13.93 2.10 0.19
mm 52 379 53 52 354 53 5
SG-80519MD-A_B SGN-80519MD-A_B ¾
in 2.29 15.43 2.35 2.29 14.43 2.35 0.19
mm 58 392 60 58 367 60 5
SG-80528MD-A_B SGN-80528MD-A_B ¾
in 2.04 16.33 2.10 2.04 15.33 2.10 0.19
mm 52 415 53 52 389 53 5
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.�4Issue C
®
SERIES SG-807CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
MODEL NO.
(in) WITH R/V LESS R/V
A B C E B C E
SG-80741MD-A_B SGN-80741MD-A_B 1
in 3.07 15.81 3.13 3.26 14.19 3.32
mm 78 402 80 83 360 84
SG-80758MD-A_B SGN-80758MD-A_B 1
in 3.24 15.98 3.30 3.43 14.36 3.49
mm 82 406 84 87 365 89
SG-80782MD-A_B SGN-80782MD-A_B 1
in 3.48 16.22 3.54 3.67 14.60 3.73
mm 88 412 90 93 371 95
SG-80711MD-A_B SGN-80711MD-A_B 1
in 3.81 16.55 3.87 4.00 14.93 4.06
mm 97 420 98 102 379 103
SG-80716MD-A_B SGN-80716MD-A_B 1
in 4.31 17.05 4.37 4.50 15.43 4.56
mm 109 433 111 114 392 116
SG-80722MD-A_B SGN-80722MD-A_B
1½S1¼D
in 4.25 20.20 4.31 4.44 18.58 4.50
mm 108 513 109 113 472 114
SG-80732MD-A_B SGN-80732MD-A_B
1½S1¼D
in 4.75 21.20 4.81 4.94 19.58 4.62
mm 121 538 122 125 497 117
S = Suction PortD = Discharge Port
For specifications, see page 680.3.
DIMENSIONS–SERIES SG-807 AND SGN-807(MD-A–“B” DRIVE)
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.�5Issue C
®
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
SERIES SG-807CAST IRON CONSTRUCTION
MODEL NO.
(in) WITH R/V LESS R/V
A B C E B C E
SG-80741MD-B_B SGN-80741MD-B_B 1
in 3.07 15.81 3.13 3.26 14.19 3.32
mm 78 402 80 83 360 84
SG-80758MD-B_B SGN-80758MD-B_B 1
in 3.24 15.98 3.30 3.43 14.36 3.49
mm 82 406 84 87 365 89
SG-80782MD-B_B SGN-80782MD-B_B 1
in 3.48 16.22 3.54 3.67 14.60 3.73
mm 88 412 90 93 371 95
SG-80711MD-B_B SGN-80711MD-B_B 1
in 3.81 16.55 3.87 4.00 14.93 4.06
mm 97 420 98 102 379 103
SG-80716MD-B_B SGN-80716MD-B_B 1
in 4.31 17.05 4.37 4.50 15.43 4.56
mm 109 433 111 114 392 116
SG-80722MD-B_B SGN-80722MD-B_B
1½S1¼D
in 3.78 20.20 4.31 4.44 18.58 4.50
mm 108 513 109 113 472 114
SG-80732MD-B_B SGN-80732MD-B_B
1½S1¼D
in 4.75 21.20 4.81 4.94 19.58 4.62
mm 121 538 122 125 497 117
S = Suction PortD = Discharge Port
For specifications, see page 680.3.
DIMENSIONS–SERIES SG-807 AND SGN-807(MD-B–“B” DRIVE)
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.�6Issue C
®
For specifications, see page 680.3.
DIMENSIONS–SERIES SG-804, SG-805 AND SGN-805(MD-A–“M” DRIVE)
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
SERIES SG-804 AND SG-805CAST IRON CONSTRUCTION
MODEL NO.(in)A
WITH R/V LESS R/VDD
MOTOR FRAME
SIZE D E F H MCB C B C
SG-80417MD-A_M ⅜ in 2.02 9.15 2.21 8.15 0.31
56C3.50 2.44 1.50 0.34
SLOT 2.56mm 51 232 56 207 8
SG-80418MD-A_M ⅜ in 2.02 9.15 2.21 8.15 0.3189 62 38 9 65mm 51 232 56 207 8
SG-80425MD-A_M ⅜ in 2.09 9.22 2.28 8.22 0.31mm 53 234 58 209 8
143TC3.50 2.75 2.00 0.34 2.88
SG-80435MD-A_M ⅜ in 2.19 9.32 2.38 8.32 0.31mm 56 237 60 211 8
89 70 51 9 73SG-80450MD-A_M ⅜ in 2.34 9.47 2.53 8.47 0.31mm 59 241 60 215 8
SG-80470MD-A_M ⅜ in 2.54 9.67 2.73 8.67 0.31
145TC3.50 2.75 2.50 0.34 2.88mm 65 246 69 220 8
SG-80518MD-A_M SGN-80518MD-A_M ½ in 2.02 9.15 2.21 8.15 0.31
89 70 64 9 73mm 51 232 56 207 8SG-80525MD-A_M
SGN-80525MD-A_M ½ in 2.09 9.22 2.28 8.22 0.31mm 53 234 58 209 8
182TC4.50 3.75 2.25 0.41 3.62SG-80535MD-A_M
SGN-80535MD-A_M ½ in 2.19 9.32 2.38 8.32 0.31mm 56 237 60 211 8
114 95 57 10 92SG-80550MD-A_M SGN-80550MD-A_M ½ in 2.34 9.47 2.53 8.47 0.31
mm 59 241 64 215 8SG-80570MD-A_M
SGN-80570MD-A_M ½ in 2.54 9.67 2.73 8.67 0.31
184TC4.50 3.75 2.75 0.41 3.62mm 65 246 69 220 8
SG-80510MD-A_M SGN-80510MD-A_M ½ in 1.84 9.97 1.84 8.97 0.31
114 95 70 10 92mm 47 253 47 228 8SG-80514MD-A_M
SGN-80514MD-A_M ¾ in 2.04 10.37 2.04 9.37 0.19mm 52 263 52 238 5
213TC*5.25 4.25 2.75 0.41 4.5SG-80519MD-A_M
SGN-80519MD-A_M ¾ in 2.29 10.87 2.29 9.87 0.19mm 58 276 58 251 5
133 108 70 10 114SG-80528MD-A_M SGN-80528MD-A_M ¾ in 2.04 11.77 2.04 10.77 0.19
mm 52 299 52 274 5 * Motor shaft must be modified to resemble 182TC-184TC shaft length, diameter and key.
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
Section 680Page 680.�7Issue C
®
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
SERIES SG-807CAST IRON CONSTRUCTION
MODEL NO.(in)A
WITH R/V LESS R/V MOTOR FRAME
SIZE D E F H MCB C B CSG-80741MD-A_M
SGN-80741MD-A_M 1 in 3.07 11.25 3.26 9.6356C
3.50 2.44 1.50 0.34 SLOT 2.56mm 78 286 83 245 89 62 38 9 65
SG-80758MD-A_M SGN-80758MD-A_M 1 in 3.24 11.42 3.43 9.80
143TC3.50 2.75 2.00 0.34 2.88
mm 82 290 87 24989 70 51 9 73SG-80782MD-A_M
SGN-80782MD-A_M 1 in 3.48 11.66 3.67 10.04145TC
3.50 2.75 2.50 0.34 2.88mm 88 296 93 25589 70 64 9 73SG-80711MD-A_M
SGN-80711MD-A_M 1 in 3.81 11.99 4.00 10.37mm 97 305 102 263
182TC4.50 3.75 2.25 0.41 3.62
SG-80716MD-A_M SGN-80716MD-A_M 1 in 4.31 12.49 4.50 10.87 114 95 57 10 92
mm 109 317 114 276184TC
4.50 3.75 2.75 0.41 3.62SG-80722MD-A_M
SGN-80722MD-A_M1½S 1¼D
in 4.25 15.64 4.25 15.02114 85 70 10 92mm 108 397 108 356
213TC*5.25 4.25 2.75 0.41 4.50SG-80732MD-A_M
SGN-80732MD-A_M1½S 1¼D
in 4.75 16.64 4.75 15.02133 108 70 10 114mm 121 423 121 382
* Motor shaft must be modified to resemble 182TC-184TC shaft length, diameter and key.
For specifications, see page 680.3.
DIMENSIONS–SERIES SG-807 AND SGN-807(MD-A–“M” DRIVE)
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
®
SERIES SG-807CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
MODEL NO.(in)A
WITH R/V LESS R/VB C E B C E
SG-80741MD-A_M SGN-80741MD-A_M 1
in 3.07 11.25 3.13 3.26 9.63 3.32mm 78 286 80 83 245 84
SG-80758MD-A_M SGN-80758MD-A_M 1
in 3.24 11.42 3.30 3.43 9.80 3.49mm 82 290 84 87 249 89
SG-80782MD-A_M SGN-80782MD-A_M 1
in 3.48 11.66 3.54 3.67 10.04 3.73mm 88 269 90 93 255 95
SG-80711MD-A_M SGN-80711MD-A_M 1
in 3.81 11.99 3.87 4.00 10.37 4.06mm 97 305 98 102 263 103
SG-80716MD-A_M SGN-80716MD-A_M 1
in 4.31 12.49 4.37 4.50 10.87 4.56mm 109 317 111 114 276 116
SG-80722MD-A_M SGN-80722MD-A_M
1½S1¼D
in 4.25 15.64 4.31 4.25 14.02 4.31mm 108 397 109 108 356 109
SG-80732MD-A_M SGN-80732MD-A_M
1½S1¼D
in 4.75 16.64 4.81 4.75 15.02 4.81mm 121 423 122 121 382 122
S = Suction PortD = Discharge Port
For specifications, see page 680.3.
DIMENSIONS–SERIES SG-807 AND SGN-807MD-A–“M” DRIVE(FOOTED BRACKET)
Footed bracket is only available for up to 145TC frame motors (4.5” rabbet) - 180TC and 210TC motor frames with 8.5” rabbet are only available with footless bracket, see page 680.17
Section 680Page 680.�8Issue D
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008
®
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.
SERIES SG-807CAST IRON CONSTRUCTION
MODEL NO.(in)A
WITH R/V LESS R/VB C E B C E
SG-80741MD-B_M SGN-80741MD-B_M 1
in 2.60 13.97 3.79 2.80 12.35 3.98mm 66 355 96 71 314 101
SG-80758MD-B_M SGN-80758MD-B_M 1
in 2.77 14.14 3.96 2.97 12.52 4.15mm 70 359 101 75 318 105
SG-80782MD-B_M SGN-80782MD-B_M 1
in 3.01 14.38 4.20 3.21 12.76 4.39mm 76 365 107 82 324 112
SG-80711MD-B_M SGN-80711MD-B_M 1
in 3.34 14.17 4.53 3.54 13.09 4.72mm 85 374 115 90 332 120
SG-80716MD-B_M SGN-80716MD-B_M 1
in 3.84 15.20 5.03 4.04 13.59 5.22mm 98 386 128 103 345 133
SG-80722MD-B_M SGN-80722MD-B_M
1½S1¼D
in 3.78 18.35 4.97 3.78 16.73 4.97mm 96 466 126 96 425 126
SG-80732MD-B_M SGN-80732MD-B_M
1½S1¼D
in 4.28 19.35 5.47 4.28 17.73 5.47mm 109 491 139 109 450 139
S = Suction Port D = Discharge Port
For specifications, see page 680.5.
DIMENSIONS–SERIES SG-807 AND SGN-807MD-B–“M” DRIVE
Coupling will accept motor frames 182TC-256TC. 254TC-256TC will require shaft modification reducing shaft extension by ⅝”.
Section 680Page 680.�8.�Issue C