28
vibration and structural isolation construction /industrial products Technical data for Regupol ® • RAV100 • RAV200 • RAV300 • RAV400 • RAV500 • RAV600

vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

Embed Size (px)

Citation preview

Page 1: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

vibration andstructuralisolationconstruction /industrial products

Technical data for Regupol®

• RAV100• RAV200• RAV300• RAV400• RAV500• RAV600

Page 2: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

2

Regupol® RAV100

Regupol® RAV200

Regupol® RAV300

Regupol® RAV400

Regupol® RAV500

Regupol® RAV600

Product range ApplicationsConstructionBuilding isolationFoundation isolationStructural isolationResilient seatingsFloating floorsStairs and landings

IndustrialInertia plinthsMachinery mounting pads/stripsMachine foundationsMass spring systemsPlant roomsGeneral workshop machinery

General M&E plantACU’sRefrigeration equipmentPumpsLift motorsGeneratorsBoilersPressesGuillotinesMilling machines

InfrastructureRail and tunnel constructionRoad and bridge construction

Page 3: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

3

The Regupol® portfolio provides access to

a range of high performing and cost effective

anti-vibration solutions, designed to overcome

all types of vibration challenges in any

industry sector.

Manufactured from polyurethane-bound

rubber granulate, Regupol® products are fully

recyclable. A wide choice of material grades are

available, including products with a load bearing

range up to and including 1.5N/mm².

The selection of a Regupol® system will

depend on a number of factors, including load,

area and natural frequency required of the

isolation material.

With a high load bearing capacity and excellent

damping properties, Regupol® maintains its

performance over a long lifespan. It has also

been independently tested by the Institute of

Structural Dynamics at DresdenTechnical

University for static and dynamic behaviour.

Supplied in easy to lay rolls or individually cut

pads/strips, Regupol® is quick and easy to install.

Regupol® is one of the leading brands for the

isolation of vibration. Standard and bespoke

solutions can be offered, for the most simple

and complex applications.

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

Regupol®

1.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

construction / industrialIsolation of structure borne noise and vibration

Page 4: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

4

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

RAV1001.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

1 Load Deflection

Load

range(N

/mm

2 )

Deflection (mm)

Samples: 300mm x 300mm

0.050

0.040

0.030

0.020

0.010

0.000

17mm

51mm

34mm

0 1 2 3 4 5 6 7 8 9 10 11 12

RAV100

Page 5: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

5

Samples: 300mm x 300mm

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Natural frequency (Hz)

Disturbingfrequency(H

z)

-40 dB/99% -30 dB/97%

-20 dB/90%

-10 dB/69%

0 dB/0%

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

2 Vibration Isolation

RAV100Lo

adrange(N

/mm

2 )

0.050

0.045

0.040

0.035

0.030

0.025

0.020

0.015

0.010

0.005

0.000

51mm 34mm 17mm

Natural frequency (Hz)

3 Natural Frequency

RAV100

Parameter: Power transmission loss (dB), isolation factor in %

Page 6: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

6

Specific load (N/mm2)

Elastic

mod

ulus

(N/m

m2 )

40 Hz

5 Hz

static

Samples: 300mm x 300mm x 34mm

1.8

1.6

1.4

1.2

1.0

0.8

0.6

0.4

0.2

0.00.000 0.005 0.01 0.015 0.020 0.025 0.030 0.035 0.040 0.045 0.050

4 Modulus of Elasticity

RAV100

5 Dynamic Stiffness

Dynam

icstiffness

(N/m

m3 )

0.06

0.05

0.04

0.03

0.02

0.01

0.00

60

50

40

30

20

10

0

Permanent load (N/mm2)

40 Hz

5 Hz

static

Samples: 300mm x 300mm x 34mm

0.000 0.010 0.02 0.030 0.040 0.050

Dynam

icstiffness

(MN/m

3 )

RAV100

10 Hz

10 Hz

Page 7: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

7

Technical InformationMeasured 30 minutes after decompression

Compression Set DIN 53572 approx. 4.10 % with 50% deformation/23˚C after 72 hrs.

Tensile Strength DIN 53571 0.30 N/mm2 Minimum

Elongation at Break DIN 53571 60 % Minimum

Tear-Resistance DIN 53515 3.0 N/mm Minimum

Static Modulus Similar Tangential modulusof Elasticity to EN 826 0.10-0.44 N/mm2 see fig. 5

Dynamic Modulus DIN 53513 0.15-1.10 N/mm2 Depending on load and frequency,of Elasticity see fig. 5

The information on this data sheet is based on the current state of our knowledge and experience and is subject tochanges and production-related variations without notice.

Relativede

flection(%

ofthickness)

Loading time (hrs)

0.025 N/mm2

1 10 100 1000 10000 100000

6 Long-term Creep Test

RAV1008

6

4

2

0

Samples: 300mm x 300mm x 34mmFurther creep test data available upon request

Physical PropertiesRegupol® is made of polyurethane-bound rubber granulate.Thickness: 17mm*Roll dimensions: 10m x 1.25m (strips and/or pads are available upon request)Permanent static load range: 0.05 N/mm2

* Dimpled on one side

Page 8: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

8

1 Load Deflection

Load

range(N

/mm

2 )

Deflection (mm)

Samples: 300mm x 300mm

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

RAV2001.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

0.10

0.09

0.08

0.07

0.06

0.05

0.04

0.03

0.02

0.01

0.00

30mm15mm 45mm

60mm

RAV200

0 1 2 3 4 5 6 7 8

Page 9: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

9

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Natural frequency of the system (Hz)

Disturbingfrequency(H

z)

-40 dB/99% -30 dB/97%

-20 dB/90%

-10 dB/69%

0 dB/0%

Parameter: Power transmission loss (dB), isolation factor in %

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

2 Vibration Isolation

RAV200Lo

adrange(N

/mm

2 )

0.10

0.09

0.08

0.07

0.06

0.05

0.04

0.03

0.02

0.01

0.00

45mm

60mm

30mm

15mm

Natural frequency (Hz)

Samples: 300mm x 300mm

3 Natural Frequency

RAV200

Page 10: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

10

Specific load (N/mm2)

Elastic

mod

ulus

(N/m

m2 )

40 Hz

10 Hz

5 Hz

static

Samples: 300mm x 300mm x 30mm

3.5

3.0

2.5

2.0

1.5

1.0

0.5

0.0

0.00 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10

4 Modulus of Elasticity

RAV200

5 Dynamic Stiffness

Dynam

icstiffness

(N/m

m3 )

0.10

0.08

0.06

0.04

0.02

0.00

100

80

60

40

20

0

Permanent load (N/mm2)

40 Hz

10 Hz

5 Hz

static

Samples: 300mm x 300mm x 30mm

0.00 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10

Dynam

icstiffness

(MN/m

3 )

RAV200

Page 11: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

11

Relativede

flection(%

ofthickness)

Loading time (hrs)

0.05 N/mm2

1 10 100 1000 10000 100000

6 Long-term Creep Test

RAV2004

3

2

1

0

Samples: 300mm x 300mm x 30mmFurther creep test data available upon request

Technical InformationMeasured 30 minutes after decompression

Compression Set DIN 53572 approx. 4.0 % with 50% deformation/23˚C after 72 hrs.

Tensile Strength DIN 53571 0.40 N/mm2 Minimum

Elongation at Break DIN 53571 70 % Minimum

Tear-Resistance DIN 53515 3.40 N/mm Minimum

Mechanical Loss Factor DIN 53513 - -

Static Modulus Similar to Tangential modulusof Elasticity EN 826 0.8-0.90 N/mm2 see fig. 5

Dynamic Modulus DIN 53513 0.6-2.20 N/mm2 Depending on load and frequency,of Elasticity see fig. 5

The information on this data sheet is based on the current state of our knowledge and experience and is subject tochanges and production-related variations without notice.

Physical PropertiesRegupol® is made of polyurethane-bound rubber-granulate.Standard thickness: 15mm (other thicknesses are available upon request)Roll dimensions: 10m x 1.25m (strips and/or pads are available upon request)Permanent static load range: 0.1 N/mm2

Page 12: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

12

1 Load Deflection

Load

range(N

/mm

2 )

Samples: 300mm x 300mm

Deflection (mm)

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

RAV3001.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

0.10

0.09

0.08

0.07

0.06

0.05

0.04

0.03

0.02

0.01

0.00

50mm 100mm

RAV300

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

Page 13: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

13

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Natural frequency of the system (Hz)

Disturbingfrequency(H

z)

-40 dB/99% -30 dB/97%

-20 dB/90%

-10 dB/69%

0 dB/0%

Parameter: Power transmission loss (dB), isolation factor in %

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

2 Vibration Isolation

RAV300Lo

adrange(N

/mm

2 )

0.10

0.09

0.08

0.07

0.06

0.05

0.04

0.03

0.02

0.01

0.00

100mm 50mm

Natural frequency (Hz)

Samples: 300mm x 300mm

3 Natural Frequency

RAV300

Page 14: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

14

Specific load (N/mm2)

Elastic

mod

ulus

(N/m

m2 )

40 Hz

10 Hz

5 Hz

static

Samples: 300mm x 300mm x 50mm

3.5

3.0

2.5

2.0

1.5

1.0

0.5

0.00.00 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10

4 Modulus of Elasticity

RAV300

5 Dynamic Stiffness

Dynam

icstiffness

(N/m

m3 )

0.07

0.06

0.05

0.04

0.03

0.02

0.01

0.00

70

60

50

40

30

20

10

0

Permanent load (N/mm2)

40 Hz

10 Hz

5 Hz

static

Samples: 300mm x 300mm x 50mm

0.00 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10

Dynam

icstiffness

(MN/m

3 )

RAV300

Page 15: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

15

Relativede

flection(%

ofthickness)

Loading time (hrs)

0.05 N/mm2

1 10 100 1000 10000 100000

6 Long-term Creep Test

RAV3006

5

4

3

2

1

0

Samples: 300mm x 300mm x 50mmFurther creep test data available upon request

The information on this data sheet is based on the current state of our knowledge and experience and is subject tochanges and production-related variations without notice.

Technical InformationMeasured 30 minutes after decompression

Compression Set DIN 53572 approx. 5.40 % with 50% deformation/23˚C after 72 hrs.

Tensile Strength DIN 53571 0.33 N/mm2 Minimum (measured on a 10-cm-layer)

Elongation at Break DIN 53571 50 % Minimum (measured on a 10-cm-layer)

Tear-Resistance DIN 53515 2.30 N/mm Minimum (measured on a 10-cm-layer)

Static Modulus Similar to Tangential modulusof Elasticity EN 826 0.25-0.75 N/mm2 see fig. 5

Dynamic Modulus DIN 53513 0.60-2.90 N/mm2 Depending on load and frequency,of Elasticity see fig. 5

Physical PropertiesRegupol® is made of polyurethane-bound rubber-granulate.Standard thickness: 50mmSheet dimensions:1000mm x 500mm (strips and/or pads are available upon request)Permanent static load range: 0.1 N/mm2

Page 16: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

16

1 Load Deflection

Load

range(N

/mm

2 )

Deflection (mm)

Samples: 300mm x 300mm

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

RAV4001.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

0.25

0.20

0.15

0.10

0.05

0.00

15mm 30mm

45mm

60mm

0 1 2 3 4 5 6 7 8 9 10 11

RAV400

Page 17: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

17

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Natural frequency of the system (Hz)

Disturbingfrequency(H

z)

-40 dB/99% -30 dB/97%

-20 dB/90%

-10 dB/69%

0 dB/0%

Parameter: Power transmission loss (dB), isolation factor in %

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

2 Vibration Isolation

RAV400Lo

adrange(N

/mm

2 )

0.25

0.20

0.15

0.10

0.05

0.00

60mm

30mm

15mm

45mm

Natural frequency (Hz)

Samples: 300mm x 300mm

3 Natural Frequency

RAV400

Page 18: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

18

Specific load (N/mm2)

Elastic

mod

ulus

(N/m

m2 )

40 Hz

10 Hz

5 Hz

static

Samples: 300mm x 300mm x 30mm

6

5

4

3

2

1

00.00 0.05 0.10 0.15 0.20 0.25

4 Modulus of Elasticity

RAV400

5 Dynamic Stiffness

Dynam

icstiffness

(N/m

m3 )

0.20

0.15

0.10

0.05

0.00

200

150

100

50

0

Permanent load (N/mm2)

40 Hz

10 Hz

5 Hz

static

Samples: 300mm x 300mm x 30mm

0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.200 0.225 0.250

RAV400

Dynam

icstiffness

(MN/m

3 )

Page 19: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

19

Relativede

flection(%

ofthickness)

Loading time (hrs)

0.125 N/mm2

1 10 100 1000 10000 100000

6 Long-term Creep Test

RAV4006

5

4

3

2

1

0

Samples: 300mm x 300mm x 30mmFurther creep test data available upon request

The information on this data sheet is based on the current state of our knowledge and experience and is subject tochanges and production-related variations without notice.

Technical InformationMeasured 30 minutes after decompression

Compression Set DIN 53572 approx. 4.60 % with 50% deformation/23˚C after 72 hrs.

Tensile Strength DIN 53571 0.65 N/mm2 Minimum

Elongation at Break DIN 53571 65 % Minimum

Tear-Resistance DIN 53515 6.0 N/mm Minimum

Static Modulus Similar to Tangential modulusof Elasticity EN 826 1.20-1.90 N/mm2 see fig. 5

Dynamic Modulus DIN 53513 1.10-4.40 N/mm2 Depending on load and frequency,of Elasticity see fig. 5

Physical PropertiesRegupol® is made of polyurethane-bound rubber-granulate.Standard thickness: 6mm/15mm (other thicknesses available upon request)Roll dimensions: 10m x 1.25m (strips and/or pads are available upon request)Permanent static load range: 0.25 N/mm2

Page 20: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

20

Load

range(N

/mm

2 )

Deflection (mm)

Samples: 270mm x 270mm

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

RAV5001.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0.00 1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 Load Deflection

RAV500

10mm

20mm 30mm 40mm

50mm

60mm

Page 21: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

21

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Natural frequency of the system (Hz)

Disturbingfrequency(H

z)

Parameter: Power transmission loss (dB), isolation factor in %

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

Load

range(N

/mm

2 )

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0.0

10mm

20mm

30mm40mm

50mm

60mm

Natural frequency (Hz)

Samples: 270mm x 270mm

3 Natural Frequency

RAV500

2 Vibration Isolation

RAV500

-40 dB/99% -30 dB/97%

-20 dB/90%

-10 dB/69%

0 dB/0%

Page 22: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

22

Specific load (N/mm2)

Elastic

mod

ulus

(N/m

m2 )

40 Hz

10 Hz

5 Hz

static

Samples: 270mm x 270mm x 20mm

16

14

12

10

8

6

4

2

00.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

4 Modulus of Elasticity

RAV500

5 Dynamic Stiffness

Dynam

icstiffness

(N/m

m3 )

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0.0

800

700

600

500

400

300

200

100

0

Permanent load (N/mm2)

40 Hz

10 Hz

5 Hz

static

Samples: 270mm x 270mm x 20mm

0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

Dynam

icstiffness

(MN/m

3 )

RAV500

Page 23: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

23

Relativede

flection(%

ofthickness)

Loading time (hrs)

0.4 N/mm2

1 10 100 1000 10000 100000

6 Long-term Creep Test

RAV5004

3

2

1

0

Samples: 270mm x 270mm x 30mmFurther creep test data available upon request

The information on this data sheet is based on the current state of our knowledge and experience and is subject tochanges and production-related variations without notice.

Technical InformationMeasured 30 minutes after decompression

Compression Set DIN 53572 approx. 5.90 % with 50% deformation/23˚C after 72 hrs.

Tensile Strength DIN 53571 0.90 N/mm2 Minimum

Elongation at Break DIN 53571 85 % Minimum

Tear-Resistance DIN 53515 8.0 N/mm Minimum

Static Modulus Similar to Tangential modulusof Elasticity EN 826 2.50-5.50 N/mm2 see fig. 5

Dynamic Modulus DIN 53513 3.0-8.80 N/mm2 Depending on load and frequency,of Elasticity see fig. 5

Physical PropertiesRegupol® is made of polyurethane-bound rubber-granulate.Standard thickness: 6mm/10mm (other thicknesses available upon request)Roll dimensions: 10m x 1.25m (strips and/or pads are available upon request)Permanent static load range: 0.8 N/mm2

Page 24: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

24

1 Load Deflection

Load

range(N

/mm

2 )

Deflection (mm)

Samples: 200mm x 200mm

Load Ranges

RAV100 RAV200/300 RAV400 RAV500 RAV600

RAV6001.50

0.80

0.25

0.10

0.05

0.00

Load

range(N

/mm

2 )

1.5

1.4

1.3

1.2

1.1

1.0

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0.00 1 2 3 4 5 6 7 8 9 10

RAV600

10mm

20mm

30mm40mm

50mm

60mm

Page 25: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

25

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Natural frequency of the system (Hz)

Disturbingfrequency(H

z)

-40 dB/99% -30 dB/97%

-20 dB/90%

-10 dB/69%

0 dB/0%

Parameter: Power transmission loss (dB), isolation factor in %

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

2 Vibration Isolation

RAV600Lo

adrange(N

/mm

2 )

1.5

1.4

1.3

1.2

1.1

1.0

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0.0

Natural frequency (Hz)

Samples: 200mm x 200mm

3 Natural Frequency

RAV600

10mm

20mm

30mm40mm50mm

60mm

Page 26: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

26

Specific load (N/mm2)

Elastic

mod

ulus

(N/m

m2 )

40 Hz

5 Hz

static

Samples: 200mm x 200mm x 20mm

40

35

30

25

20

15

10

5

00.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5

4 Modulus of Elasticity

RAV600

10 Hz

5 Dynamic Stiffness

Dynam

icstiffness

(N/m

m3 )

2.0

1.8

1.6

1.4

1.2

1.0

0.8

0.6

0.4

0.2

0.0

2000

1800

1600

1400

1200

1000

800

600

400

200

0

Permanent load (N/mm2)

40 Hz

10 Hz

5 Hz

static

Samples: 200mm x 200mm x 20mm

0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5

Dynam

icstiffness

(MN/m

3 )

RAV600

Page 27: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus

27

Relativede

flection(%

ofthickness)

Loading time (hrs)

0.75 N/mm2

1 10 100 1000 10000 100000

6 Long-term Creep Test

RAV6004

3

2

1

0

Samples: 200mm x 200mm x 30mmFurther creep test data available upon request

The information on this data sheet is based on the current state of our knowledge and experience and is subject tochanges and production-related variations without notice.

Technical InformationMeasured 30 minutes after decompression

Compression Set DIN 53572 approx. 5.0 % with 50% deformation/23˚C after 72 hrs.

Tensile Strength DIN 53571 2.20 N/mm2 Minimum

Elongation at Break DIN 53571 120 % Minimum

Tear-Resistance DIN 53515 16.0 N/mm Minimum

Static Modulus Similar Tangential modulusof Elasticity to EN 826 9.80-14.0 N/mm2 see fig. 5

Dynamic Modulus DIN 53513 4.0-18.50 N/mm2 Depending on load and frequency,of Elasticity see fig. 5

Physical PropertiesRegupol® is made of polyurethane-bound rubber-granulate.Standard thickness: 10mm (other thicknesses available upon request)Roll dimensions: 8m x 1.25m (strips and/or pads are available upon request)Permanent static load range: 1.5 N/mm2

Page 28: vibration and structural isolation - Anti-Vibration Products · vibration and structural isolation ... Tear-Resistance DIN53515 2.30 N/mm Minimum(measuredona10-cm-layer) StaticModulus