Embed Size (px)
Citation preview
155
ELINE / ELINE-D
VERTICAL IN-LINE PUMP
TECHNICAL FEATURESELINE: Vertical centrifugal pumps, single impeller,volute casing, non-self priming pump, in-line executive,with mechanical seal.Hydraulically designed in line with DIN 24255 standard.
ELINE-D: This model comprises two verticalcentrifugal pumps in a single pump casing.Non-self priming pump, in-line executive with mechanical seal.
CONSTRUCTIONCasing: One piece volute casing, in-line execution.Inlet-outlet in line with the same dimensions.
ELINE-D: This model comprises two twin verticalpumps hydraulically separated at the discharge bya flap. Standard shaft motor.
ELINE: Features a motor with standard coupled shaft.All models have a connection for fitting a pressure gaugeand, if requested, another connection can be provided forthe suction. A drain valve is mounted in the spacer.
Impeller: Closed radial impeller. Hydraulic compensationis achieved through holes on the discharge side in all models.
Shaft seal: Mechanical seal mounted on stainless steel shaft.
APPLICATIONS• Pressure heating systems• Cold water circuits• Cooling circuits towers• Water supply (non-drinking)• Pressure increase• Distribution of domestic hot water supplyMainly used in industry for pumping clear liquids, free ofabrasive particles in suspension and chemically neutral.
MATERIAL
WORKING ADVANTAGES• Can be mounted without support in line up to 3kW• Silent operation• Reduce space• Easy assembly / disassembly• Maintenance-free and leakage-free• The ELINE-D model can be used for duty /
standby or duty / assist
GENERAL DATA (ELECTRIC MOTOR)
GENERAL DATA (ELECTRIC MOTOR)• Three phase IP55, with flange• Rotation speed: 1450 – 2900 r.p.m.• Voltage: up to 4kW: 230/400V;
higher than 4kW: 400/700V• Frequency: 50Hz (60 Hz upon request)• Insulation: Class F• Ambient temperature: 40°C max
MODEL DEFINITION
Designation Standard Material Optional
Casing Cast iron (GG-25)
Spacer Cast iron (GG-25)Impeller Cast iron (GG-20) BronzeShaft Stainless steel (1.4401)O-rings KLINGERITMechanical seal Carbon/Ceramic
Size Flow Total differential Temperature Max. SpeedPump type DN Q (m3/h) head H (m) t (°C)* r.p.m.EBARA ELINE 40-50-65-80-100 ≤ 160 ≤58 -10°C > + 120 ≤ 3.600EBARA ELINE-D 40-50-60-80 ≤ 220 ≤ 58 -10°C > + 120 ≤ 3.600
EBARA ELINE - E 40 - 160 / 0.75
Motor power in kW.
Impeller diameter in mm.
Inlet/Outlet diameter in mm.
Twin pump with standardcouplet shaft
Pump type
156
(*) Model available in single and twin executions.(**) Model only available in twin execution.
(*) Model available in single and twin executions.
ELINE / ELINE-D
SELECTION CHART
ELINE / ELINE-D 1450 R.P.M.
ELINE / ELINE-D 2900 R.P.M.
157
ELINE / ELINE-D
SECTIONAL DRAWING AND COMPONENT LIST
Part Designation1 Pump casing2 Impeller rear wear ring3 Fixing screw spacer-motor4 Fixing nut spacer-motor5 Pressure gauge plug6 O-ring - pressure gauge plug7 O-ring - casing-spacer8 Impeller key9 Impeller nut10 Plane washer under impeller nut11 Spring washer under impeller nut12 Impeller13 Mechanical seal14 Impeller front wear ring15 Air vent16 Fixing screw casing to bracket17 Base plate18 Shaft19 Shaft key20 Spacer21 Fixing screw motor-spacer22 Fixing nut motor-spacer23 O-ring - pressure gauge plug (OPTIONAL)24 Pressure gauge plug (OPTIONAL)25 Motor26 Plane washer motor-spacer27 Plane washer - casing-spacer28 Plane washer - base plate29 Discharge flap (ELINE-D only)30 Drainplug
158
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
EL 40-125 EL 40-160
EL 50-125 EL 50-160
159
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
EL 50-200 EL 50-250
EL 65-125 EL 65-160
160
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
EL 65-200 EL 65-250
EL 80-125 EL 80-160
161
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
EL 80-200 EL 80-250
EL 100-160 EL 100-200
162
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
EL 100-250 EL125-200
EL 125-250 EL 150-200
163
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
EL 150-250 EL 200-250
164
EL 40-125 EL 40-160
EL 50-125 EL 50-160
ELINE / ELINE-D
PERFORMANCE CURVE 2900 min-1
165
EL 50-200 EL 65-125
EL 65-160 EL 80-125
ELINE / ELINE-D
PERFORMANCE CURVE 2900 min-1
166
EL 80-160 EL 100-200
EL 125-200
ELINE / ELINE-D
PERFORMANCE CURVE 2900 min-1
167
ELD 40-160 ELD 50-200
ELD 50-250 ELD 65-160
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
168
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
ELD 65-200 ELD 65-250
ELD 80-160 ELD 80-200
169
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
ELD 80-250 ELD 100-160
ELD 100-200 ELD 100-250
170
ELINE / ELINE-D
PERFORMANCE CURVE 1450 min-1
ELD 125-200 ELD 125-250
ELD 150-200 ELD 150-250
171
ELINE / ELINE-D
PERFORMANCE CURVE 2900 min-1
ELD 40-160 ELD 50-200
ELD 65-160 ELD 80-160
172
ELINE / ELINE-D
PERFORMANCE CURVE 2900 min-1
ELD 80-250 ELD 100-160
ELD 100-200 ELD 100-250
173
ELINE / ELINE-D
PERFORMANCE CURVE 2900 min-1
ELD 125-200
PERFORMANCE TABLE
174
ELINE
ELINE-D
FLANGESDIMENSIONAL TABLE
DN d4 k D N x d2
DIN 2532 PN
40 88 110 150 4 x 18 50 102 125 165 4 x 18 65 122 145 185 4 x 18 80 138 160 200 8 x 18 100 158 180 220 8 x 18 125 188 210 250 8 x 18 150 212 240 285 8 x 22 200 268 295 340 8 x 22
ELINE / ELINE-D
DIMENSION
175
ELINE / ELINE-D
DIMENSION TABLE
ModelMotor Characteristic
rpmFrame size
Dimension (mm)
(*) Motor with reduced flange(1) Not standard frame
4 Pole 2 Pole
176
Model Motor Characteristic Dimension (mm)Frame
size rpm4 Pole 2 Pole
ELINE / ELINE-D
DIMENSION TABLE
