Version 1

1

INSTALLATION MANUAL& OPERATIONINSTRUCTIONS

SINGLE POST CAR PARKING LIFT

Version 1

2

Date: 5/06/2018

TABLE OF CONTENTS

CHAPTER 1: USER’S RECORD 3

CHAPTER 2: INTRODUCTION 4

CHAPTER 3: SAFETY INSTRUCTIONS 5

CHAPTER 4: DESCRIPTION AND TECHNICAL DATA 9

CHAPTER 5: INSTALLATION INSTRUCTIONS 12

CHAPTER 6: INSTALLATION STEPS 17

CHAPTER 7: OPERATION INSTRUCTIONS 30

CHAPTER 8: MAINTENANCE 34

CHAPTER 9: ELECTRIC & HYDRAULIC DIAGRAMS 36

CHAPTER 10: TROUBLE SHOOTING 41

CHAPTER 11: LIMITED WARRANTY 43

NOTES 44

Version 1

3

CHAPTER 1: USER’S RECORD

RECORD BELOW INFORMATION WHICH LOCATED ON THE NAME PLATE

MODEL NO ____________________________

SERIAL NO ____________________________

CUSTOMER ____________________________

DATE OF INSTALLATION _________________

WE HEREBY DECLARED THAT THE ABOVE MENTIONED MACHINE HAS BEEN INSTALLEDCORRECTLY. ALL FUNCTIONS HAVE BEEN CHECKED AS WELL AS CORRECT OPERATINGOF ALL SAFETY DEVICES. WE CONSIDER THEREFORE THE MACHINE WORK IN GOODCONDITION.

Date of Installation The authorized technician

---------------------------- ------------------------------------

The customer

---------------------------------

(READ THIS MANUAL COMPLETELY AND PAY MORE ATTENTION TO THE INSTRUCTIONS BEFORE INSTALLING)

Version 1

4

CHAPTER 2: INTRODUCTION

This Manual has been made to supply the owner as well the user with the basic instructions for installation and a correct use of the Single post car parking lift .

Read this guide carefully before using the lift and follow the instructions given by this guide to grantit a correct function, efficiency and a long service life.

Single post car parking lift is dependant parking type where it requires valet to remove lower car away before lowering the platform.

This lift is suitable for residential parking purposes. The platform moves only vertically, so that theusers have to clear the ground level to get the higher level car down. It is hydraulic driven Type thatlifted directly by cylinder with chain connected to carriage.

This is electro-hydraulic lift used ONLY for motor vehicle parking.

The product designed according to the EN 1493:2010 and EN 14010:2003+A1:2009.Reference of Directive Machine: 2006/42/EC.

Working Principle:

1. When operating the unit and pushing UP Button, the hydraulic power unit will be electricallyactivated to pump hydraulic oil from tank to hydraulic oil cylinder.

2. The hydraulic cylinder will pull upwards the steel chain which is connected to the carriage.3. The carriage will lift the platform as both of them are connected with bolts.4. Once reaching pr-determined lifting height, the carriage will touch the limit switch and stop

the hydraulic motor.5. The ground floor under the platform is free for parking lower car.

Version 1

5

CHAPTER 3: SAFETY INSTRUCTIONS

1. Read and understand all safety warning procedures before operating the parking lift.

2. Do not install the parking lift on any asphalt surface.

3. This parking lift is designed for parking motor vehicles that weighs within its max lifting

capacity.

4. Exceeding the maximum lifting weight will cause grave damage to the lift and DANGEROUS

INJURIES for the persons.

5. This parking lift, in its standard version, is not designed for outdoor use.

6. This parking lift is not designed to be used as car service lift to do any maintenance for the

car on platform.

7. The manufacturer doesn’t bear any responsibility for any accidents or damage might

happen to the cars or/and persons due to misuse of the lift.

8. Keep hands and feet away from any moving parts. Keep feet clear of parking lift when

lowering.

9. The parking lift MUST only be used by qualified staff, properly trained for such work.

10.During installation, do not wear unfit clothes, large cloves, ties, etc, which could get caught

by moving parts of the machine.

11. The parking lift surrounding area must be free from people or objects which could be a

danger for lifting operations.

12.Use suitable handling and lifting tools/equipment such as crane, forklift, and pallet lift during

off-loading of the packages and during installation of different parts.

13.Always insure the safety devices are engaged before any attempt to work on or near

vehicle.

Version 1

6

14.The parking lift is only designed to park the entire body of vehicle, having maximum weight

not more than the lift capacity.

15.The vehicle must be centered and positioned in a stable correct way with respect to the

platform and following the instructions given by manufacturer.

16.Make sure that the lift and its devices are working correctly, according to the specific

instructions for maintenance.

17.Do not modify the parking lift without manufacturer’s written approval.

18. If the parking lift will not be used for a long period, proceed as follows:

a. Disconnect the energy source.

b. Empty the oil from the Hydraulic unit tank.

c. Grease the moving parts which might be damaged by dust or drying out.

19.Only Authorized personnel are allowed to operate the control box. Only person with

qualification for repairing electrical appliances could open control box.

20.Control box is allowed to open only after power is cut off.

21. Installation technicians should be healthy, well trained and qualified to carry on the

installation with experience for both mechanical &electrical work.

22.The car must be parked at the right direction.(See below Fig.1)

Version 1

7

WARNING SIGNS

Version 1

8

Fig.2

Fig.3

Version 1

9

CHAPTER 4: DESCRIPTION AND TECHNICAL DATA

4.1 OVERALL DESCRIPTION

1. Unit Base 2. Cover of base 3. Carriage 4. Post

5. Support beam 6. Platform (3 pcs) 7. Ramp 8. Wave plate

9. Stopper 10. Hydraulic power unit

motor

11. Oil Tank 12. Stand of control

box

13. Control

box(could be

fixed on the post)

Version 1

10

4.2 TECHNICAL DATA

4.3 Identification Plate with Serial Number:

Fig.4 Fig.5

Manufacturer Strongman Tools LtdMachine Type Single Post Car Parking Lift – Hydraulic drivenModel NO. Telford - Single PostMax Lifting Capacity 2000 KgMax Lifting Height 1820mmMax dimension of vehicle 5000*1850*1550mmMax weight of vehicle 2000 KgLock Release Type Electric lock releaseOutline Dimension 3945x 2631x 2479 mmUnit Weight 1300 KgParking Width 2000mmRise/Drop Time 60 S/50 SPower Supply/ Motor Capacity 220V/ 1Ph/ 50Hz. - 2.2 KWRun Way & Ramps Diamond Steel PlatesNoise Level ≤85dB

Platform – Middle Diamond Steel Plates and removable CorrugatedGalvanized Steel Plates

Version 1

11

4.4 Lift Dimensions

12

Version 1

CHAPTER 5: INSTALLATION INSTRUCTIONS

Strongman Tools Ltd Equipment, ensuring our customers’ safety is our primary concern. Our car parking lift was designed and built with safety. However, safety relies on proper installation and training. Prepare for a successful installation by making sure your floor meets specific requirements.

Installation technicians should be healthy, well trained and qualified to carry on the installation with experience for both mechanical &electrical work.

Use hoist / crane with suitable steel chain or woven belt to lift he package to the place you need to install. The lifting capacity of the hoist must be more than 1.5 Ton.

Fig.6

Version 1

13

5.1 Unpacking the package

Check the package and off-load the contents near the installation place.

Fig. 7

The hydraulic power unit box and standard parts & chains box are light, could be carried by hand.Then take out steel parts one by one using suitable lifting hoist (Fig. 9 is an example of hoist).

Fig. 8 Fig. 9

Version 1

14

Parts need crane or hoist to carry during off-loading the package for installing the lift

Description Weight (kg) Carrying Method

1 Runway platform (at stopper side) 85

By Crane or hoist

2 Runway platform (at ramp side) 105

3 Cover of base 48

4 Post and Carriage 325

5 Base 103

6 Mid platform 364

7 Steel plate for packaging 128

Parts with weight less than 20kg

8 ramps

Human handling9 Power unit

10 chains

11 Standard parts

5.2 SITE SELECTION:

Before installing your car parking lift, check the following: Lift Location: Always use architect’s plans when available. Check layout dimension against floor plan requirements making sure adequate space is

available. Your lift requires a 220v, 30amp, single phase, grounded electrical source. Thereshould be room enough to operate the lift in a safe manner and without restrictions.

Space Required: Please refer to the drawing for detailed installation size. Overhead Area: The area where the lift will be located should be free of overhead obstructions

such as heaters, building supports, electrical lines, doors, lights, etc. Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or

defective concrete.

Version 1

15

5.3 FLOOR REQUIREMENTS:

A leveled floor is strongly suggested for proper installation and balance lifting. Small differencesin floor slopes may be compensated by proper shims. If a floor is of questionable slope,consider the possibility of pouring a new level concrete slab.

DO NOT install car lift on any asphalt surface or any surface other than concrete.

DO NOT install car lift on expansion seams or on cracked or defective concrete.

DO NOT install car lift on a second/elevated floor without consulting building architect first.

DO NOT install car lift outdoor as it’s not designed for outdoor conditions.

New concrete must be adequately cured for at least 30 days. All models MUST be installed on 3,000 PSI reinforced concrete slab only. New Poured Concrete slab Specifications: Minimum 200 mm thickness. Old ,unleveled or damaged Concrete slab Specifications:In this case you can cut out a 1m x 1m square form the old slab, and pour new concrete to a depthof about 300mm. You can then tie this new section of slab back into the existing slab with RotaryHammer Drill drilled in. Do it under all car lift posts.Specifications of concrete must be adhered to. Failure to do so could cause car lift failure resultingin personal injury or death. The floor strength should be suitable to carry the weight of the car liftplus 2 cars, one on the ground floor and one on the platform.

5.4 Other environment requirements

Temperature required: -30 ºC to 45 ºCAir humidity： ≤80%Altitude: ≤ 2000 m

5.5 TOOLS AND EQUIPMENT NEEDED:

Appropriate lifting equipment such as forklift or Hoist. Rando HD 46 or other good quality garage hydraulic oil. Chalk line and measure tape. Rotary Hammer Drill with 3/4’’ drill bit. Sockets and Open wrench set. Vise Grips. Lithium lubricating grease

Version 1

16

5.6 PARTS LIST:

Main Parts list

Item Size (mm) Qty Item Size QtyStop plate 470*100*40 2 Oil Tank 10 L 1Base cover 1420*830 1 Steel wire rope 1Post 230*290*320 1 Chain Lh12461 1Ramp 600*470 2 Base plate 1Gusset plate 1040*745 1 Hydraulic Cylinder 1Wave plate 1040*224 8 Steel wire rope 1Middle platformrunway

1650*473 2 carriage 1

Platform Runway (AtStop plate side)

555*473 2 Hydraulic PowerUnit

1

Platform Runway (AtRamp side)

860*473 2 Operation Panel 1

Oil Hose 1

Standard Parts List

Item Size Qty Item Size QtyHex bolt, flat washer ,spring washer

M8*30 4 Nut M12 1

Hex bolt, flat washer,spring washer

M18*45 18 Chain wheel Φ110 1

Bolt M5*15 4 Roller on carriage 4Bolt M6*20 1 Oil bearing 42*38*50 5Hex bolt, flat washer,spring washer

M12*35 4 Limit switch 1

Bolt M6*25 1 Limit switch cable 2*0.5 1.5 mCountersunk bolt M6*15 1 Flat washer 16 2Countersunk bolt M10*10 1 Split cotter 2.5 4Hex bolt ,flat washer ,spring washer

M14*30 4 Elastic cylindricalpin

φ3*20 2

Hex bolt M5*30 4 Flat washer 12 1Countersunk bolt M10*15 6 Sliding block 8Anchor Bolt M18*220 12 Electromagnetic 1Bolt M4*20 4 Cable 1Expansion AnchorBolt

M20*180 8 Hose 2-JIC1/2 1

Elbow ZG1/4-JIC1/2 1

Version 1

17

5.7 BEFORE INSTALLATION

1.Identify the packaging components and check for missing parts. Contact Strongman if shortagediscovered.

2.Installation, adjusting and testing operations are to be performed by qualified staff only.3.The lift must be installed on a leveled concrete floor, having minimum thickness of 150 mm and anextension of at least 1500 mm from anchoring points.

4.The lift installation concrete surface must be relatively smooth, leveled in all directions5.After unloading the package, place it near the intended installation location.6.Dismantle the steel parts of the lift from the package.7.Remove the packing materials (steel brackets, cartoons, etc) from the installation site.

CHAPTER 6: INSTALLATION STEPS6.1 : DETERMINE LOCATION ANDMARK WITH CHALK ON THE FLOOR

1.Determine the location for installing the parking unit considering all safety instructions.2.Place the base on the floor and confirm its location before fixing to the floor.3.Mark base outline with chalk on floor to ensure no displacement occurs during installation.

Fig 10

Version 1

18

6.2 INSTALL THE BASE ON THE FLOOR.

Before this step, carry the base by crane or hoist to installation site as it is heavy.

1. Drill each anchor hole in the concrete using a rotary hammer drill. To assure full holding power, donot oversize the hole or allow drill to wobble. (Fig.11)

3. After drilling, remove dust thoroughly from each hole and make certain that the base remainsaligned with the chalk line during this process.

4. If shimming is required, insert the shims with selected thickness as necessary under the base plateanchor bolts so that when the anchor bolts are tightened, the base will be horizontal. (Fig12).

5. With the shims and anchor bolts in place, tighten by securing the nut to the base then turning2-3 fullturns clockwise. DO NOT use an impact wrench for this procedure.

Version 1

19

Fig.11

Fig.12

6.3: INSTALLATION OF CARRIAGE, CYLINDER & CHAIN INSIDE THE COLUMN (POST):Carry carriage and post by1. Insert the carriage (Fig 13) into the post from the top of the post (Fig 14).

2. Insert the chain pulley hole to the head of the cylinder.

3. Put the cylinder on the cylinder base seat at the bottom of the post (Fig 15).

4. Insert the chain inside the chain pulley and fix one side of the chain on the clamp behind thecylinder base at the bottom of the post (Fig 16).

5. Fix the other side of the chain to the carriage using threaded connection rod M20 (Fig 17 & Fig 18).

6. Fix the cover on the top of the post using bolts M18 x 45.

Version 1

20

Fig.13 Fig.14

Fig15 Fig16

Version 1

21

Fig.17 Fig.18

Fig.19

Version 1

22

Top view of post Back view of carriage and cylinder

6.4: INSTALLATION OF THE COLUMN (POST) ON THE BASE:

1．Place the column in its position over the base using proper lifting hoist.

2．Use fixing bolts M18 x 45 to connect the post base to lift base (Fig.20).

3．Fix the cover of the basement with bolts M10 x 15 (Fig.21).

Fig.20

Version 1

23

Fig 21

6.5: INSTALLATION OF THE PLATFORM

1. Lift up the middle platform using proper hoist and Install it to the carriage using bolts M18 x 45.2. Lift up the left & right platforms separately and fix them with middle one with fixing bolts

M20 x 120 (Fig.22, Fig.23, Fig.24 and Fig.25).3. Fix the lock and limit switch to the column with Hex bolts M14 x30 (Fig.26, Fig.27).4. Fix wave plates on the platforms one by one (Fig.28).

Fig.22 Fig.23

Version 1

24

Fig.24

Fig.25

Version 1

25

Lock device in the post

Fig.26

Fig.27

Version 1

26

Fig 28

Version 1

27

6.6: MOUNTING POWER UNIT

1. Fix the power unit to the column with bolts M8 x 30 (Fig 29).

Fig.29

6.7: INSTALL HYDRAULIC OIL HOSE AND FILL THE POWER UNIT TANK WITH OIL

1. Connect the oil hose between hydraulic cylinder and hydraulic power unit using integratedfitting. (Fig.30, Fig.31, Fig.32).

2. Pay attention to keep the hoses clean and free of cracks.3. Use the oil type Rando HD 46 or other good quality garage hydraulic oil to fill the hydraulic tank

up to max mark line on the tank (Fig.33).

Fig.30

Version 1

28

Fig.31 Fig.32

Fig.33

6.8: MOUNTING CONTROL BOX

1. Fix the electric control box on the stand and place the stand far away from any moving parts toavoid injuries. Make sure that the location of the control panel and its stand is suitable to haveclear view to the whole lift during lifting up & down.

2. Connect the electric cables according to attached wiring diagram in this manual.

Version 1

29

3. Fix control panel on the post, and please pay attention control panel should far away frommovable parts of lift.

Fig.34

6.9: LUBRICATION OF MOVING PARTS

1. Before operation, use proper grease to lubricate the post from inner parts where the sliding blocksare moving to ensure smooth lifting of carriage.

2. Use lithium lubricating grease to lubricate chain and pulley.

Fig. 35

Version 1

30

CHAPTER 7: OPERATION INSTRUCTIONSWARNING: DO NOT PLACE ANY VEHICLE ON THE LIFT BEFORE TRIAL OPERATION. TEST THE LIFTUP AND DOWN SEVERAL TIMES TO INSURE LOCK IS WORKING PROPERLY AND AIR IS REMOVEDFROM THE CYLINDER.

7.1 BEFORE OPERATION

1. Check the hydraulic hose and joints before use. Don’t use the machine if there is oil leakage.2. The parking lift, if its safety lock device is malfunction, shall not be used till being repaired.3. The parking lift shall not lift up or lower down a vehicle unless it’s placed correctly on the

platform.4. The manufacturer will not bear any responsibility for improper parking on the platform.5. The valet or operators shall be in a safe position during parking / retrieving the car.6. Check the electrical control panel and follow the wiring diagram for electric connections.

7.2 FUNCTION OF EACH BUTTONS

Operation panel buttons:

UP button: Press it to lift up the platform from ground level.

Down Button: Press it to lower the platform to ground level.

Emergency Stop Button: Press it to stop the whole unit immediately in case of emergency.

Buzzer and lamp: During up & down movement, the buzzer and lighting flasher will alarmand flash to warn people that the unit in operation

Stop Button: Press it to stop the platform.

Lock Button: Press it to Lock the latch to nearest position.

Remote control buttons:

A：UP button,Press it to lift up the platform from ground level.

B: Down Button, Press it to lower the platform to ground level.

C: Lock Button, Press it to Lock the latch to nearest position.

D： Empty

Version 1

31

Operation box and remote control

Version 1

32

OPERATION STEPS OF OPERATION PANEL(CONTROL PANEL)

Version 1

33

OPERATION STEPS OF REMOTE CONTROL

Parking cars:

1. Make sure platform on the ground floor2. Drive the car on the plat, and pull hand brake before leaving the car..3. Press A button(Up)4. The car will be lifted on the determined height.5. Drive the other car and park it on ground floor.

Retrieving cars:

1. Drive away the car on the ground.2. Press B button (Down)3. The car will be lifted a little bit and then go down to the floor.4. Drive the car on the plat away.

34

ild

Version 1

CHAPTER 8: MAINTENANCE

Strongman offers warranty as per Limited Warranty Statement included in this manual.

The manufacturer will not take any responsibility for improper installation and operation, overload running, improper concrete flooring (that cannot meet the requirements in the manual), normal mechanical abrasion and insufficient maintenance. The warranty will be carried out on the basis ofthe type and serial number of the equipment. Therefore, the user shall provide them to the manufacturer accurately. The several types of maintenance operations to be carried out aredescribed below. Routine maintenance for the unit will reduce maintenance cost and prolong the lifetime. The listed schedules are given for user information and they refer to normal operating conditions. They can be changed according to the kind of service, environment, frequency of use,etc.

1. DAILY PRE-OPERATION CHECK

The user should perform daily check of safety lock device .The discovery of device failure before using the left will save you from expensive property damage, lost time and serious personal injury.

Check safety lock audibly and visually while in operation. Check hydraulic connections and hoses for leakage. Check chain connections, cable connections, wiring and switch for damage. Check obstacles under platform.

2. WEEKLY MAINTENANCE

Check the cleanliness of all parts. Check the safety lock device as previously described. Check hydraulic connections and hoses for leakage. Check hydraulic oil level on tank by lowering the platform completely to the floor and check the o

level. If needed, add oil but should find where is the leakage to solve the problem. Recommende Hydraulic oil (# 46).

Check and tighten bolts, nuts and screws.

Version 1

35

3. MONTHLYMAINTENANCE

Check the tightening of all bolts &screws Check hydraulic connections and hoses for leakage and tighten the loose unions, if

necessary. Check the greasing and mechanical wear condition of chains, pins, rollers, and sliding blocks

of carriage structure and if necessary, replace the damaged parts. Check steel ropes for damage, crush or flattened. Check the tension of steel rope to avoid being loose. Check steel ropes sheaves for mechanical wear and ensure no displacement. Check steel chain tension and its fixing pins to the lift structure.

4. YEARLY MAINTENANCE (BY SKILLED PERSONS ONLY)

Lower down the platform on the floor and turn off the main electric switch. Empty the oil tank and check the condition of the hydraulic fluid. Clean the oil filter from

impurities and change oil if needed. Check the electric control box components and make sure all wiring is connected tighten. Check all electric cables to ensure neither burns nor bare wires. Clean by blower and dry brush the electric motor to remove accumulated dust which prevents

good heat exchange. Check the chains & wire ropes, if there is any mechanical wear, breakage or damage and

change it if needed.

If the above maintenance operations are carried out, there will be an advantage for the user who willfind the equipment in perfect condition each time he restarts work.

3. Service lift of main parts

1. Steel structure: 10 years2. Chain : 10 years3. Cylinder: 5 years4. Power unit :5 years5. Electric parts: 5 years

Version 1

36

CHAPTER 9: ELECTRIC & HYDRAULIC DIAGRAMS

9.1 ELECTRICAL DIAGRAM （ELECTRIC LOCK RELEASE）

220V, 50Hz, 1Ph

Version 1

37

NO CODE NAME NO CODE NAME

1 KM RELAY 8 M MOTOR

2 SB PUSH BUTTOM 9 N NEUTRAL

3 KT TIME RELAY 10 U RECTIFIER

4 KA AC RELAY 11 SQ LIMIT SWITCH

5 YV SOLENOID VALVE 12 TC TRANSFORMER

6 HL INDICATING LAMP 13 QF CIRCUIT BREAKER

7 QS MAIN SWITCH

Version 1

38

9.2 HYDRAULIC DIAGRAM

Version 1

39

1- Oil Tank 2- Oil Suction Pipe 3- Oil Filter 4- Oil Return Pipe5- Gear Pump 6- Valve Block7- 7- One Way Valve 8- Solenoid Valve9- Hydraulic Motor 10- Throttle Valve

Version 1

40

1 Filter

2 Motor

3 Gear pump

4 Relief valve

5 One-way valve

6 Cylinder

7 Solenoid valve

8 Throttle valve

9 Oil tank

Version 1

41

CHAPTER 10: TROUBLE SHOOTING

TROUBLE CAUSE SOLUTION

Pump/ Motor does not start Improper electrical hook up

Blown Fuse

Pump binding or stuck

Motor thermal overload tripped

Thermal overload in starter box

Tripped

Rewire.

Replace Fuse.

Remove (flush) or replace.

Let Cool 30 sec.

Push Button Reset.

Replace Switch.

Call Electrician.Pump/Motor operates buthas no pressure.

Wrong rotation of motor Reverse phases.

Pump/Motor operate lowflow and/or low pressure (inpressure mode)

Clogged inlet strainer due to dirt

Relief Valve (Overflow Valve)leaking or low pressure adjusted.

Manual Release (Oil Drain) Valveleaking or loose.

O-ring missing or cut

Clean strainer from dirt.

Adjust Overflow v/v pressure.Loose outside nut and clockwisetighten the overflow v/v to close.

Replace O-ring.

Pump/Motor operates butdoes not hold system

Fitting loose

Check Valve leakage

Dirt on seal

Release stem out of adjustment

O-ring missing or cut

Tighten or replace fitting.

Flush seal.

Re-adjust stem setting.

Replace O-ring.

Replace Motor.

Version 1

42

Platform doesn’t come down Latch in locking position

Release valve is blocked by

contamination

Operate to rise up to release thelocking latch before lowering.Check electromagnetic switchwhich locks/ unlock the latch.Inspect valve and clean orreplace

Air in oil Loose inlet connectionOr low oil levelLeaky or blown Oil Seals

Tighten connection.Add oil.Replace oil seal.

Motor does not run when

energized

Breaker thrown or Fuse blownMotor thermal overload trippedThermal overload in Starter BoxTrippedCheck Micro SwitchFaulty wiring, connections

Reset or replace.Wait for overload to cool.Push Button to reset.Replace if necessary.Check the start capacitor.

Oil blows out the Breather /Filter Port

Oil overload.

Vehicle has been lowered too fast.

Empty oil tank to ½ - 2/3 full.

Restrict lowering withThrottle V/V (Oil SpeedAdjusting Screw).

Cylinder will not lift load Oil Seal damage to PistonOil leaking from cylinder front

Call distributor for instructions.

Oil requirements Use Hydraulic Oil (Rando HD 46)or equivalent

Call distributor for instructions.

Lift makes abnormal noise Carriage roller is dry and requiresgrease.The motor is overloaded.

Suction filter clogged or hydraulicoil contaminated.

Add grease to the roller.

Reduce load or increase therelief v/v setting pressure.

Change hydraulic fluid aftercleaning suction filter and tank.

Lift doesn’t move up/downsmoothly

Lift posts and foot are not balanced Check level, re-shim with small& thin steel sheets as required.

43

Version 1

CHAPTER 11: LIMITED WARRANTYThe user of car lifts is solely responsible for using this equipment safely and considering all of the safety guidelines

provided in the User Manual and on the warning labels/signs provided with the lift.

Your new car parking lift warranty is two years for structure of the lift against breakage or failure and one year for all

electrical, mechanical, and hydraulic components, parts or devices to be free of manufacturing defects both in material

and workmanship. The warranty period begins from the date of shipment. The warranty doesn’t cover equipment that will

be stored without being in operation for more than 6 months from date of shipment.

The Purchaser shall notify the manufacturer by official email the claim supported by photos and videos showing the defect

in the equipment that has been detected upon arrival inspections, installation or use of the equipment, immediately, and

no later than 2 days following the detection of the defect of the equipment. Should the Purchaser fail to provide the

manufacturer with such notification, the manufacturer shall be discharged of any liability for defects in the equipment that

reasonably could have been detected by such inspections.

The manufacturer shall, at its own choice, either repair or replace the defected parts after being sent by purchaser to

manufacturer factory, freight prepaid, which prove upon inspection to be defective. The maximum liability of Strongman

under this Limited Warranty is limited to the EXW purchase price of the Equipment.

This warranty does not extend to defects caused by damage or broken in transit/shipping, or due to directly or indirectly

misuse, abuse, vehicle impact, negligence, faulty installation, fire, floods, acts of God, accidents, voltage fluctuation,

normal wear & tear, lack of required maintenance, lack of lubrication, 3rd party interference, equipment modification

outside of the Strongman factory and other conditions beyond the control of the manufacturer.

This warranty with all stated policies is based on the model and serial number of the equipment. This data must be

provided for all warranty claims.

Strongman makes no warranty or representation with respect to the compliance of any Equipment with local safety or

product standard codes, and any failure to comply with such codes shall not be considered a defect of material or

workmanship under this warranty. Strongman shall not be liable for any direct or consequential damages resulting from

such noncompliance.

Except as stated herein, Strongman will not be liable for any loss, injury, or damage to persons or property, nor for direct, indirect, or consequential damage of any kind, resulting from failure or defective operation of said Equipment.

Strongman reserves its right to make design changes or add improvements to its equipment without incurring any

obligation to make such changes on previously sold equipment.

This Manual is ends here. Please follow all instructions and if you have any comments, please send email to us with your comments and if possibly with illustrative photos.

Version 1

44

NOTES