Vento Phantom r4i Manual

8/3/2019 Vento Phantom r4i Manual

1/25

VENTO PHANTOM R4i USER S MANUAL


2/25

Thank you for choosing Vento

Design and Production byVento North America

Phone 858.597.7520

Fax 858.597.7462

E-mail [email protected]

For more information visit us online

www.vento.com

Vento Phantom R4i Are trademarks registered by Vento Motorcycles Inc.

Made in U.S.A.
http://www.vento.com/


3/25

Congratulations on your purchase!

This booklet is your guide to basic operation and maintenance for your Vento Phantom r4i

We recommend you read and understand this manual. Should you have any questions orcomments, you can always contact us or visit your nearest Vento authorized dealer.

At the end of this manual you will find the service stubs for your motorcycle.

It is very important to have these stubs filled out by your Vento Authorized Dealer / Service Centerevery time there is service or repair done on your vehicle.

For repairs, please contact your local Vento Authorized Dealer / Service Center.

Thank you again, enjoy!


4/25

REPLACEMENT PARTS

Should you need parts for your Vento Motorcycle, Scooter or ATV you may contact our partsdepartment at: [email protected]. For more information log on to our website atwww.vento-motorcycles.com or call 1 866 MY VENTO.

Use only genuine Vento parts for your vehicle.
http://www.vento-motorcycles.com/


5/25

TABLE OF CONTENTS

Symbols . .. 1Tire Warranty ... 2Reporting Safety Defects . . 9Motorcycle Identification 10Emission Standards... .. 11Controls and Displays .12

Compartments .6Riding . .. 7Storage . 8Regular Check-Ups . 9Washing your Motorcycle.. ... ..10Technical Data .. 11How to Ride 12Daily Check ..15

Parking .16After Inactivity 14Battery 10Engine Oil .7Air Filter 8Technical Information .9Fuse 11Washing .12Storage ...13Specifications 15Front Bag ... 16Main Commands ..... 17Starter Switch ...18Indicators Description . .19


6/25

The meanings of some symbols in the manual are as follows:

WARNING

Indicates potential hazard that could result in injury or death

CAUTION

Indicates potential hazard that could result in vehicle damage

NOTICE

Indicates special information to make procedures easier or instructions clear.


7/25

TIRE WARRANTY

The Tires on your Vento Motorcycle, Scooter or ATV are separately warranted by theirmanufacturer. Contact us by telephone at 1 866 MY VENTO or write us an e-mailto:[email protected] with any questions or comments.

NOTE: IN ORDER TO RECEIVE THE BENEFITS OFFERED BY THE TIREMANUFACTURER WARRANTY IT IS NECESSARY THAT YOU SUPPLY US WITH ALLTHE INFORMATION REQUESTED IN THE FORM ON PAGE 6.

Please mail the completed form on reverse to:

Attn: Tire Warranty DepartmentVento Motorcycles5355 Mira Sorrento Pl. 100San Diego, CA 92121


8/25

IMPORTANT

IN THE EVENT OF A RECALL, WE CAN REACHYOU ONLY IF WE HAVE YOUR CONTACTINFORMATION. YOU MUST SEND IN THIS CARDTO BE ON OUR RECALL LIST. DO IT TODAY.

OWNERS NAME TELEPHONE

OWNERS ADDRESS

CITY STATE ZIP

ADDRESS OF DEALER WHICH SOLD TIRES / VEHICLE

CITY

STATE ZIP

VIN SERIAL # FRONT SERIAL # REAR

TIRE MAKE


9/25

REPORTING SAFETY DEFECTS

If you believe that your vehicle has a defect, which could cause a crash or could causeinjury or death, you should immediately inform the National Highway Traffic SafetyAdministration in addition to notifying Vento North America.

If the National Highway Traffic Safety Administration receives similar complaints, it mayopen an investigation, and if it finds that a safety defect exists in a group of vehicles, it may

order a recall and remedy campaign. However, the National Highway Traffic SafetyAdministration cannot become involved in any problems between you, your dealer or VentoMotorcycles, Inc.

To contact the National Highway Traffic Safety Administration you may either call the AutoSafety Hotline toll-free at 1-800-424-9393 (366-0123 in Washington, DC area) or write to:

United States Department of TransportationNational Highway Traffic Safety Administration

400 7

th

Street SW (NSA-11)Washington, DC 20590


10/25

VEHICLE IDENTIFICATION

VEHICLE IDENTIFICATION NUMBER (VIN)

This number identifies your entire vehicle. This number is used by federal and state entities for regulation, safety, pollutionand registration purposes. Our warranty system is based on the VIN and engine numbers as well. Your motorcycle wasdelivered to you with a metal plate permanently attached to its frame with this number engraved. A federal label attachedto the surface under the seat includes safety, tire pressure information, model year and the VIN.

ENGINE NUMBER

Your engine number will only be used by Authorized Vento Dealers and Service Centers for identification. This number isengraved on the engine cover.

Removing or tampering with any of these numbers is a federal crime. Avoid scratching or damaging this number whileservicing or repairing your motorcycle.

Should you have an issue with any of these numbers, contact your State s Motor Vehicle Department in addition tonotifying Vento North America.

You may need to know this number for vehicle registration, warranty claims, theft or in case of a recall.


11/25

EMISSION INFORMATION

U.S. ENVIRONMENTAL PROTECTION AGENCY STANDARDS

This vehicle has been designed, manufactured, equipped and certified to conform to all applicable U.S. Environment Protection Agencyfederal regulations and so that it is free from defects in material and workmanship which could cause the vehicle to fail conforming toFederal Environmental Protection Agency regulations during the time period under Federal Emission Control Systems Warranty.

CALIFORNIA E.P.A. (C.A.R.B.)

This vehicle and its engine are certified to meet the California Air Resources Board (CARB) emission and evaporative standards.

The emissions label located on the bottom surface of the seat on your motorcycle contains statements, specifications, basic tune- up, andcertified family names required by the regulations mentioned above. The evaporative emissions diagram can also be found there.

See your warranty booklet for further information regarding the Emissions Warranty.


12/25

CONTROLS AND DISPLAYS

Left turn signal

Odometer

Speedometer

Right turn signal

High Beam Indicator

Fuel Gauge

Alarm Indicator.

Flashes when left turn signal is activated.

Indicates distance covered in miles (total distance)

Indicates speed in miles per hour.

Flashes when right turning signal is activated.

Lights up when headlights are on the High Beam position .

Flashes when alarm system is armed


13/25

LEFT HAND CONTROLS

Horn button - Press the switch to sound the horn

Turn signal switch - Slide switch left when turning left, slide switch right when turning right and push in to cancel.

Low beam / High beam Switch For High beam Turn upwards / For Low beam Turn downwards.

Engine Kill Switch Turn into the X position to shut off. Turn into the O position to start the engine.

RIGHT HAND CONTROLS

Headlights / Running Lights - Slide switch towards the left up to first level and running lights will come on; slide once again to the

next level the head lights will turn on.

Electric Starter button - Press the electric starter button for a maximum of 5 seconds. NOTICE:

If the engine does not start the first time, try again after 30 seconds.

DO NOT use the electric starter after long periods of inactivity, doing so can drain the battery.


14/25

IGNITION SWITCH

1. ON Position (Engine Ignition)

Engine can be started

Electrical devices such as horn, lights, etc. can be activated .

Key cannot be removed.

2. OFF (Engine Shut-off)

Engine cannot be started.

Electrical devices such as horn, lights, etc. are inoperable

Keys can be removed

3. LOCK Position

Steering lock is engaged

Engine cannot be started.

Electrical devices such as horn, lights, etc. are inoperable

Keys can be removed

NOTES:

Rotating the key switches the electrical circuitry ON and OFF

WARNING:

Do Not Turn the ignition key when the engine is running. Use thekill switch to shut-off, then rotate the key counter-clockwisetowards the OFF position.

NOTICE:

If the engine is shut-off, please turn the ignition switch to the

OFF or LOCK position. Failure to do so can cause batterydrain or damage on the electrical system.

STEERING LOCK OPERATION

For your protection, activate the steering lock when leaving yourvehicle parked or unattended.

1. Turn handle bar to the left or right limit.

2. Turn the key from OFF towards the LOCK position.

3. Remove the key.

To unlock:

Insert the key and rotate it to the OFF or ON position.


15/25

COMPARTMENTS

SEAT LUGGAGE COMPARTMENT

When the seat is open you will find the luggage box, which canhold up to 20 Lbs. (10 KG)

(Operating manual and other documents can be stored here.)

ATTENTION:

Food easily affected by temperature and combustible materialsshouldn t be stored in the luggage box.

Opening and closing seat compartment lock:

1. Insert key and turn to left to open.

2. Lift the seat from the rear to open it.

3. Drop seat and press it firmly to close.

The seat is locked automatically.

FRONT GLOVECOMPARTMENT

The front compartment can hold goods weighing up to about3Lbs. (1.5 kg.)

How to use the front compartment:

1. Insert key and turn towards the left to open lock buckle.

2. Open the cover by pulling outwards.

3. Please use the rubber strip or a rope to fasten luggage.

WARNING: DO NOT OVERLOAD. PLEASE FOLLOW THELOADING CAPACITIES STATED ON THIS MANUAL.OVERLOADING CAN CAUSE YOUR MOTORCYCLE TOA F F E C T S T A B I L I T Y A N D H A N D L I N G .


16/25

FUEL TANK

1. Insert key and turn the key left to open lock.

2. Turn fuel tank cap to the left and pull out to remove.

3. Add fuel to the tank.

4. To lock, press firmly into place and remove the key.

FUEL TANK CAPACITY IS 1.6 GALLONS (6 LITERS).

TURN OFF ENGINE BEFORE FUELING

USE UNLEADED FUEL ONLY (87 OCTANE)

WARNING:

Fuel is combustible and can cause fire under certain conditions

When fueling vehicle, do so in an open, ventilated area.

Avoid skin contact with, and inhalation or ingestion of fuel.

Do not overfill. Doing so can deteriorate body panels.


17/25

RIDING

STARTING THE ENGINE

Make sure that fuel and oil levels are adequate.

DANGER:

DO NOT START THE ENGINE IN AIRLESS OR AIRTIGHTCONDITIONS SINCE EXHAUST FUMES CONTAINPOISONOUS SUBSTANCES THAT CAN CAUSE DEATH.

1. Set the kick lever (main stand)

2. Driver must stand to the left of the vehicle.

3. Turn the ignition switch to the ON position.

4. Hold the steering handle firmly.

5. Kick start the engineor press the electric starter button (fornot more than 5 secondswhile applying the rear brake.

DO NOT USE THE ELECTRIC STARTER ON FIRST USEAFTER LONG PERIODS OF INACTIVITY.

NOTICE:

It is recommended to warm-up the engine by driving slowly

during the first few minutes or miles of the trip.

DRIVING TIPS

Before starting your motorcycle, squeeze the rear brake with theleft hand and grasp the handle with the right hand and then pushthe vehicle forward so as to turn main support back up.

Do not grasp the seat to turn the main stand up / down.

Climb astride the vehicle. Hold the handle bar with both handsand stride the vehicle from the left side. Keeping your left foot onthe ground for support, climb over the vehicle with your right leguntil you are seated firmly

If driving with passenger, flip open the rear foot pegs ; otherwise,keep them closed.

CAUTION:

In order to prevent the vehicle from rushing out please squeezethe rear brake leveruntil the engine is running and then release itslowly.

When pulling out of park, loosen the rear brake, rotate thesteering handle slowly and the vehicle will begin to move.


18/25

SPEED ADJUSTMENT

Use the throttle grip on the steering handle to adjust speed

Towards the driver to increase speed.

Release to reduce speed.

BRAKE SYSTEM

To brake, first slow the vehicle by turning the throttle grip awayfrom you. Next, grasp the front and rear brake bars

simultaneously and squeeze them until the brakes apply.

Remember to apply the brakes gradually and steadily.

If you need to stop while going uphill, always use both brakes.Don t try to maintain position with the throttle alone, as this willdamage the engine.

WARNING:

Always brake early on damp, snowy or frozen ground, since thebrakes will need more time to take effect than on a normal roadsurface.

Don t brake repeatedly during long downhill rides since this can

damage the vehicle.

Check brake oil level regularly.

PARKING

Do not lean your motorcycle against walls.

Stand your motorcycle on a flat, even surface.

Do not leave your motorcycle unattended, especially if theengine is running or the key inserted.

Do not sit on your vehicle while it is resting on the mainstand.

Avoid touching any parts that may be hot such as the

engine, chassis, wheels or brakes.


19/25

STORAGE

CAUTION:

SHIELD THE ENGINE AND MUFFLER WITH A DUST COVERAFTER THE SURFACE HAS COOLED DOWN.

NOTICE:

Please pay utmost attention to the following for long periods ofstorage.

It is of great importance to wax all parts to prevent rust.

To preserve the battery and reduce leakage, please take thebattery out and put it in a ventilated place away fromexposure to light. If you don t plan to remove it for storage,please disconnect the negative electrode.

Drain off all the fuel in the carburetor to prevent rusting.

AFTER INACTIVITY

Rinse your motorcycle

Check battery charge and recharge if needed

Check oil and fuel levels

Do a thorough check of all parts and processes before

using

ON FIRST USE

Proper running of the engine to ensure a long life for your vehiclerequires that you take the following precautions:

For the first 100 Miles (160 KM), drive slowly and use the brakesgently. Avoid sudden or prolonged use of the brakes. This willensure optimum performance and extend the life of the vehicle.

After the first 500 Miles (160-800 KM) do not drive yourmotorcycle at speeds greater than 80% of the maximum speed.

Gradually start driving your motorcycle at higher speeds (subjectto the local speed limits) until complete break-in or maximumperformance has been reached.


20/25

REGULAR CHECK-UPS

CHECKING YOUR MOTORCYCLE

Regular checks are necessary in order to maintain yourvehicle in optimum condition and to help prevent accidents

Always remember to check your vehicle carefully beforedaily use.

An overall check every six months ensures optimumperformance.

WARNING:

Breakdowns or accidents may happen if these checks areneglected.

Regular checks are required even if the vehicle has been lyingidle. In fact, it is of particular importance to check your vehiclethoroughly after long periods of disuse.

Check more frequently if vehicle is being used under extremeweather, rainy or dusty conditions.

We recommend that difficult checks be done at your local(or the nearest) service center.

DAILY CHECK

Brake System

Check for smooth functioning and sensitivity of response.

Make sure that brake fluid level is proper

Tires

Check for cracks or other damage.

Ensure no abnormal abrasion.

Check for depth of tire thread.

Engine

Adequate engine oil. See Engine Oil for details.

Check for unusual noises or rattles.

Check for appropriate acceleration/deceleration response.


21/25

BRAKE SYSTEM

Lookat the fluid level indicator.

Squeeze the brake lever tightly to check if the displacement ofthe fluid indicator line falls below the indicated brake fluid limit, ifit falls below minimum, replenish brake fluid.

Through the rear of the brake fixture. If the disc appearsabraded, indicates that it needs to be replaced. Check the traveldistance of the grip again after adjustment.

If brake system oil level is below minimum, replenish with brakefluids DOT3 or DOT4 only. Do not use inferior quality orrecycled brake fluid.

Squeeze rear brake handle until resistance increases andmeasure if the further stroke is in this range.Adjust the gap byturning the regulating nut. Turn clockwise increase the traveldistance, Counter-clockwise to decrease.

CAUTION:

When replenishing, prevent the brake fluid from getting in contact with the paintwork to avoid fading or chapping of body panels.

Be sure to keep the surface of the adjusting nut in perfect contact

with the pillar surface of the pin.

ENGINE OIL

Checking Oil Level

1. Keep the motorcycle on its main support on level ground.

2. Remove oil level gauge. Oil should be between maximum

and minimum levels.

3. Add oil if required.

USE SG IN API CLASSIFICATION OR SAE 10W-40

Engine Oil Replacement

1. Remove drain screw of oil cap

2. Drain engine oil (It is easier to drain the engine oil when the

engine is warm)

3. Pour proper quantity of oil slowly into the gear box using a

plastic cone or a funnel.

4. Tighten back drain screw.

5. Tighten the oil plug after completion.

CHECK OIL LEVEL PERIODICALLY.


22/25

AIR FILTER

The air filter should be cleaned after approximately every 1000Miles (1600 KM), depending on usage and conditions.

If the vehicle is being used often in rainy or dusty conditions, theair filter should be cleaned more frequently.

Cleaning

1. Set the motorcycle on its main support. 2. Loosen the five screws that fasten the air filter cover in

place to remove the cover.3. Remove the filter and cover the intake manifold to avoid

foreign objects entering the engine.4. Clean the filter with solvent and let it dry5. Submerge wick into clean filter oil.6. Reinstall air filter.7. Put cover back on. Tighten.

Remember to replace the air filter if it is worn out, dirty orclogged up.

Improper fixing of the air filter may cause dust to enter theengine and affect performance or damage the pistonchamber.

BATTERY

Check the electrolyte of the battery every 1000 Miles (1600 KM).

Battery check

1. Make sure the key ignition switch on OFF2. Open the battery cover using a Phillips head screwdriver.3. Replenish the battery electrolyte except for the contents of

the sealed container which needs no inspection.

FUSES AND WIRING

If any electrical component is not working or is workingimproperly or the engine does not start, check your motorcyclefuses and wiring.

Fuse Checking

To check, remove fuse from casing; replace if damaged. You candetermine whether a fuse is damaged by looking through at thecenter of the fuse and examine if the connector is burnt or cut.Should the latter be the case, replace the fuse.

All electrical components should be replaced only withoriginal Ventoparts. Do not use non-standard fuses orwith improper capacity. See the Technical Data .


23/25

WASHING YOUR MOTORCYCLE

DO NOT USE SOLVENTS OR STRONG DETERGENTS; THEYCAN DAMAGE THE FINISH OF YOUR MOTORCYCLE.

1. Mop the dirt with a soft cloth while rinsing with warm water.

2. Use a neutral detergent and wash the motorcycle with waterto get rid of stubborn dirt or grime.

3. Dry any residual water with a clean and soft cloth.

We recommend that our users apply mixed wax . It is important tobe careful with the paintwork and plastic parts gently to prevent

scratches and chipping.

CAUTION:

Clean the motorcycle only after the engine has cooledKeep water out of the muffler, air cleaner and electricalappliances to prevent rusting and short-circuitingPlease ride slowly and carefully after washing your motorcyclesince brake performance may be affected by residual water

It is recommended that the motorcycle is dry before riding it.


24/25

TECHNICAL INFORMATION

SPECIFICATIONS

Engine Type 4-Stroke, Aircooled Bi2 150Max. Power 9.38 BHP @ 7500 RPMMax. Torque 0.86 Kgfm @ 5000 RPMStarting System Electric/ KickIgnition CDIClutch Type Automatic, CentrifugalTransmission CVT AutomaticVehicle Length 76.7 In. (1950 mm)Width 25.5 In. (675 mm)Height 44.5 In. (1130 mm)Seat Height 31.1 In (790 mm)Dry Weight 253 LBS. (115 Kg)Passengers 2 PeopleSuspension HydraulicFront Brake Drilled Disk, Anti-Lock HRear Brake Drum, MechanicalFuel Tank Capacity 1.6 Gallons (6 Liter)Engine Oil Capacity 33 Fl. Oz. (1 Liter)Default Brake Lever Travel In. (15 25 mm.Tire Size Front 130/60-13Tire Size Rear 130/60-13Spark Plug Type A7RTC/NHSP/LDO21Spark Plug Clearance 0.6 0.8 mmBattery Type 12V 6AH /YTX7A-BSHeadlight Low Beam / High Beam 12V / 18WBrake / Tail Light Bulb 12V / 15WTurn Signal Bulb 12V / 10WFuse Capacity 8 Amp


25/25

WWW.VENTO.COM

Vento isn t just a motorcycle It s an Attitude!
http://www.vento.com/

Documents

Vento Phantom r4i Manual