VCCI TEST REPORT...Report No.: V110531E05 4 of 27 Report Format Version 4.0.0 1 CERTIFICATION PRODUCT : Remote control Harmony 200 BRAND NAME : Logicool MODEL NO. : N-I0005 APPLICANT

Report No.: V110531E05 1 of 27 Report Format Version 4.0.0

VCCI TEST REPORT REPORT NO. : V110531E05

MODEL NO. : N-I0005

RECEIVED : May 31, 2011

TESTED : June 01 to 02, 2011

ISSUED : June 15, 2011

APPLICANT : Logitech Inc.

VCCI MEMBER NO. : 532

ADDRESS : 6505 Kaiser Drive, Fremont, CA 94555-3614 USA.

ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory

LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan

This test report consists of 27 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF, NVLAP, NIST or any government agencies. The test results in the report only apply to the tested sample.


Table of Contents RELEASE CONTROL RECORD................................................................................. 3

1 CERTIFICATION............................................................................................. 4

2 SUMMARY OF TEST RESULTS..................................................................... 5 2.1 MEASUREMENT UNCERTAINTY .................................................................. 5

3 GENERAL INFORMATION ............................................................................. 6 3.1 GENERAL DESCRIPTION OF EUT................................................................ 6 3.2 GENERAL DESCRIPTION OF TEST MODE .................................................. 7 3.3 DESCRIPTION OF SUPPORT UNITS............................................................ 8 3.4 CONFIGURATION OF SYSTEM UNDER TEST............................................. 9 4 EMISSION TEST........................................................................................... 11

4.1 CONDUCTED EMISSION MEASUREMENT .................................................11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...............................11 4.1.2 TEST INSTRUMENTS ...................................................................................11 4.1.3 TEST PROCEDURE ..................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ......................................................... 12 4.1.5 TEST SETUP ................................................................................................ 12 4.1.6 EUT OPERATING CONDITIONS.................................................................. 13 4.1.7 TEST RESULTS............................................................................................ 14 4.2 RADIATED EMISSION MEASUREMENT ..................................................... 16 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................... 16 4.2.2 TEST INSTRUMENTS .................................................................................. 17 4.2.3 TEST PROCEDURE ..................................................................................... 18 4.2.4 DEVIATION FROM TEST STANDARD ......................................................... 18 4.2.5 TEST SETUP ................................................................................................ 19 4.2.6 EUT OPERATING CONDITIONS.................................................................. 19 4.2.7 TEST RESULTS (MODE 1)........................................................................... 20 4.2.8 TEST RESULTS (MODE 2)........................................................................... 22 5 PHOTOGRAPHS OF THE TEST CONFIGURATION.................................... 24

6 APPENDIX - INFORMATION ON THE TESTING LABORATORIES............. 27


RELEASE CONTROL RECORD

ISSUE NO. REASON FOR CHANGE DATE ISSUED V110531E05 Original release June 15, 2011


1 CERTIFICATION

PRODUCT : Remote control Harmony 200 BRAND NAME : Logicool

MODEL NO. : N-I0005 APPLICANT : Logitech Inc.

TESTED : June 01 to 02, 2011 TEST SAMPLE : ENGINEERING SAMPLE

STANDARDS : V-3/2011.04, TECHNICAL REQUIREMENTS, Class B V-4/2010.04, SUPPLEMENTARY TEST CONDITIONS FOR

EQUIPMENT UNDER TEST

The above equipment (Model: N-I0005) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report.

PREPARED BY : , DATE: June 15, 2011 ( Midoli Peng, Specialist )

APPROVED BY :

, DATE: June 15, 2011

( Ken Lu, Manager )


2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications:

Standard Test Type Result Remarks

Conducted Test PASS Meets Class B Limit Minimum passing margin is -20.30 dB at 0.224 MHz

Telecommunication ports conducted test

NA Not Applicable V-3/2011.04, Class B

Radiated Test (30MHz ~ 6GHz)

PASS Meets Class B Limit Minimum passing margin is -6.39 dB at 120.00 MHz

2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

MEASUREMENT FREQUENCY UNCERTAINTY VCCI SITE

REGISTRATION NO. Conducted emissions 150kHz ~ 30MHz 2.45 dB C-817 Radiated emissions 30MHz ~ 1GHz 3.73 dB R-782


3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT

PRODUCT Remote control Harmony 200 MODEL NO. N-I0005 POWER SUPPLY DC 3V from battery POWER CORD NA DATA CABLE USB cable (Shielded, 0.6m, with one core) I/O PORT USB port x 1 ASSOCIATED DEVICES

NA

NOTE:

1. The EUT’s highest operating frequency is 48MHz.

2. The EUT was pre-tested under the following test modes for three different axes placements: Test Mode Description Mode A X-Y plane Mode B X-Z plane Mode C Y-Z plane From the above modes, the worst emission level was found in Mode A. Therefore only the test data of the modes were recorded in this report individually.

3. The above EUT information was declared by manufacturer and for more detailed feature descriptions, please refer to the manufacturer's specifications or User's Manual.


3.2 GENERAL DESCRIPTION OF TEST MODE 1. For Remote + USB mode: the radiated evaluation (30-1000MHz), 230V/50Hz

(for EN 55022), 120V/ 60Hz (for FCC Part 15), 100V/50Hz (for VCCI) had been covered during the pre-test. The worst emission data was founded at 230V/50Hz and recorded in the applied test report.

2. The EUT was tested with the following modes:

Conducted test Test Mode Description Mode 1 Remote + USB Radiated test Test Mode Description Mode 1 Remote control only Mode 2 Remote + USB

Note: The test Configuration was defined by the applicant requirement.


3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests.

Conducted (Mode 1) / Radiated test (Mode 1) NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID

1 DVD PLAYER LG HT202SF-A0 NA NA 2 SPEAKER LG SH22SF-S NA NA

Radiated test (Mode 2) NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID

1 PC DELL DCSCMF 8KKB32S FCC DoC

2 MONITOR DELL E2210C CN-0W366R-64180-05J-0CVS

FCC DoC

3 PRINTER EPSON LQ-300+II G88Y074086 FCC DoC 4 MODEM ACEEX 1414 0206026775 IFAXDM1414

5 KEYBOARD DELL SK-8115 CN-0J4635-71616-53A-0CH2

FCC DoC

6 MOUSE DELL M056UOA FOROOSWW FCC DoC

Conducted (Mode 1) / Radiated test (Mode 1) NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS

1 NA 2 Audio cable, unshielded, 1m, with one core

Radiated test (Mode 2) NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS

1 USB cable, shielded, 0.6m 2 1.8m braid shielded wire , VGA & DVI connector , with two cores.

3 1.8m braid shielded wire, terminated with DB25 and Centronics connector via metallic frame, w/o core

4 1.2 m braid shielded wire, terminated with DB25 and DB9 connector via metallic frame, w/o core.

5 2m foil shielded wire, USB Connector, w/o core. 6 1.8m foil shielded wire, USB Connector, w/o core.

NOTE: All power cords of the above support units are non shielded (1.8m).


3.4 CONFIGURATION OF SYSTEM UNDER TEST

For Radiated test (Mode 1):

CONTROL ROOM

Audio cable (1m)

2. SPEAKER

Wireless

EUT

1. DVD PLAYER


For Conducted (Mode 1) / Radiated test (Mode 2):

TEST TABLE

3. PRINTER

4. MODEM 5. KEYBOARD

2. MONITOR EUT

USB cable (0.6m)

1. PC

6. MOUSE


4 EMISSION TEST

4.1 CONDUCTED EMISSION MEASUREMENT

4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT

Class A (dBuV) Class B (dBuV) FREQUENCY (MHz)

Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50

NOTES: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range of 0.15

to 0.50 MHz. (3) All emanations from a class A/B digital device or system, including any network of

conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above.

4.1.2 TEST INSTRUMENTS

DESCRIPTION & MANUFACTURER

MODEL NO. SERIAL NO. CALIBRATED DATE

CALIBRATED UNTIL

ROHDE & SCHWARZ Test Receiver

ESCS 30 100287 Mar. 02, 2011 Mar. 01, 2012

Line-Impedance Stabilization Network (for EUT)

NSLK 8127 8127-523 Sep. 17, 2010 Sep. 16, 2011

Line-Impedance Stabilization Network (for Peripheral)

ENV-216 100072 June 11, 2010 June 10, 2011

RF Cable (JYEBAO) 5DFB CONCAB-003 Aug. 06, 2010 Aug. 05, 2011 50 ohms Terminator 50 3 Nov. 03, 2010 Nov. 02, 2011

Software BV ADT_Cond_V7.3.7

NA NA NA

Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are

traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. A. 3 The VCCI Con A Registration No. is C-817.


4.1.3 TEST PROCEDURE a. The EUT was placed 0.4 meters from the conducting wall of the shielded room

with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument.

b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference.

c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20dB) were not recorded.

4.1.4 DEVIATION FROM TEST STANDARD No deviation

4.1.5 TEST SETUP

N o t e : 1 .S u p p o r t u n i ts w e re c o n n e c t e d t o s e c o n d L IS N .

2 .B o t h o f L IS N s ( A M N ) a r e 8 0 c m f ro m E U T a n d a t le a s t 8 0 c m

f r o m o t h e r u n i ts a n d o t h e r m e ta l p la n e s

V e r t ic a l R e f e re n c e

G ro u n d P la n e

4 0 c m

8 0 c m

T e s t R e c e iv e r

H o r iz o n ta l R e f e r e n c eG r o u n d P la n e

E U T

L IS N

For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration.


4.1.6 EUT OPERATING CONDITIONS

1. Turned on the power of all equipment. 2. PC ran the test program "Client.BAT" to enable EUT under

transmission/receiving condition continuously via one USB cable.


4.1.7 TEST RESULTS

TEST MODE Mode 1 6dB BANDWIDTH 9 kHz

INPUT POWER

(SYSTEM) 100Vac, 50 Hz PHASE Line (L)

ENVIRONMENTAL CONDITIONS

25 deg. C, 75 % RH, 1001 hPa TESTED BY Kyle Huang

Freq. Corr. Reading Value Emission Level Limit Margin

No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.150 0.37 44.59 - 44.96 - 66.00 56.00 -21.04 - 2 0.224 0.36 42.00 - 42.36 - 62.66 52.66 -20.30 - 3 0.556 0.37 24.70 - 25.07 - 56.00 46.00 -30.93 - 4 0.892 0.40 22.95 - 23.35 - 56.00 46.00 -32.65 - 5 11.840 0.80 37.86 - 38.66 - 60.00 50.00 -21.34 - 6 24.035 1.23 33.72 - 34.95 - 60.00 50.00 -25.05 -

REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value.


TEST MODE Mode 1 6dB BANDWIDTH 9 kHz

INPUT POWER

(SYSTEM) 100Vac, 50 Hz PHASE Neutral (N)


25 deg. C, 75 % RH, 1001 hPa TESTED BY Kyle Huang

Freq. Corr. Reading Value Emission Level Limit Margin

No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.150 0.10 44.01 - 44.11 - 66.00 56.00 -21.89 - 2 0.220 0.10 37.63 - 37.73 - 62.81 52.81 -25.08 - 3 0.556 0.12 31.62 - 31.74 - 56.00 46.00 -24.26 - 4 0.892 0.15 24.73 - 24.88 - 56.00 46.00 -31.12 - 5 11.262 0.60 39.89 - 40.49 - 60.00 50.00 -19.51 - 6 24.035 1.47 33.90 - 35.37 - 60.00 50.00 -24.63 -

REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value.


4.2 RADIATED EMISSION MEASUREMENT

4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT LIMITS BELOW 1GHz

Class A (at 10m) Class B (at 10m) FREQUENCY (MHz) dBuV/m dBuV/m 30 - 230 40 30

230 - 1000 47 37

LIMITS ABOVE 1GHz Class A (dBuV/m) (at 3m) Class B (dBuV/m) (at 3m)

FREQUENCY (GHz) AVERAGE PEAK AVERAGE PEAK

1 to 3 56 76 50 70 3 to 6 60 80 54 74

NOTE: (1) The lower limit shall apply at the transition frequencies. (2) Emission level (dBuV/m) = 20 log Emission level (uV/m).

(3) All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above.

FREQUENCY RANGE OF RADIATED MEASUREMENT (FOR UNINTENTIONAL RADIATORS) Highest frequency generated or used in the EUT or on which the EUT operates

or tunes (MHz) Upper frequency of measurement

range (MHz)

Below 108 1000 108-500 2000

500-1000 5000

Above 1000 Up to 5 times of the highest frequency or 6 GHz, whichever is less


4.2.2 TEST INSTRUMENTS

DESCRIPTION & MANUFACTURER

MODEL NO. SERIAL NO. CALIBRATED DATE

CALIBRATED UNTIL

ADVANTEST Spectrum Analyzer U3751 160200410 Sep. 08, 2010 Sep. 07, 2011

PSA Sevies Spectrum Analyzer E4446A MY46180622

111 115 UK6 Apr. 25, 2011 Apr. 24, 2012

HP Pre_Amplifier 8449B 3008A01922 Sep. 24, 2010 Sep. 23, 2011 ROHDE & SCHWARZ Test Receiver ESCS 30 100375 Mar. 09, 2011 Mar. 08, 2012 SCHWARZBECK Broadband Antenna VULB-9168 263 Apr. 23, 2011 Apr. 22, 2012 Schwarzbeck Horn_Antenna BBHA9120 D123 Sep. 07, 2010 Sep. 06, 2011 Schwarzbeck Horn_Antenna BBHA 9170 BBHA9170153 Jan. 17, 2011 Jan. 16, 2012

RF Switches EM-H-01-1 1009 Nov. 04, 2010 Nov. 03, 2011 RF Cable 8DFB STACAB-001 Nov. 04, 2010 Nov. 03, 2011

Software ADT_Radiated_V7.6.15.9.2 NA NA NA

CT Antenna Tower & Turn Table TT100 ADT01 NA NA

CORCOM AC Filter MRI2030 107/108 NA NA

Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA.

2. The horn antenna, preamplifier (model: 8449B) and Spectrum Analyzer (model: E4446A) are used only for the measurement of emission frequency above 1GHz if tested.

3. The test was performed in Open Site No. A. 4. The VCCI Site Registration No. is R-782. 5. The FCC Site Registration No. is 91097. 6. The CANADA Site Registration No. is IC 7450G-1.


4.2.3 TEST PROCEDURE For below 1GHz test: a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at

a 10-meter open field site. The table was rotated 360 degrees to determine the position of the highest radiation.

b. The EUT was set 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower.

c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement.

d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading.

e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz.

NOTE:

1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency below 1GHz.

4.2.4 DEVIATION FROM TEST STANDARD No deviation


4.2.5 TEST SETUP

<Frequency Range below 1GHz>

10m

Ant. Tower 1-4m Variable

Turn Table

EUT& Support Units

Ground Plane

Test Receiver

80cm

3m-above 1GHz

For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration.

4.2.6 EUT OPERATING CONDITIONS Same as 4.1.6


4.2.7 TEST RESULTS (MODE 1)

TEST MODE Mode 1 FREQUENCY RANGE 30-1000 MHz


28 deg. C, 72 % RH, 1001 hPa

DETECTOR FUNCTION & BANDWIDTH

Quasi-Peak,

120kHz

TESTED BY Timmy Hu

ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 10 M

No. Freq. (MHz)

Emission Level

(dBuV/m)

Limit (dBuV/m)

Margin (dB)

Antenna Height

(m)

Table Angle

(Degree)

Raw Value

(dBuV)

Correction Factor (dB/m)

1 119.98 18.16 QP 30.00 -11.84 4.00 H 14 5.17 12.99 2 152.54 20.77 QP 30.00 -9.23 4.00 H 52 5.42 15.35 3 196.34 16.98 QP 30.00 -13.02 4.00 H 209 4.46 12.52 4 240.44 24.68 QP 37.00 -12.32 3.64 H 160 10.66 14.02 5 356.00 22.48 QP 37.00 -14.52 2.79 H 121 4.47 18.01 6 465.00 24.42 QP 37.00 -12.58 2.40 H 261 3.48 20.94

REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit.

4. Margin value = Emission level – Limit value.




28 deg. C, 72 % RH, 1001 hPa


Quasi-Peak,

120kHz

TESTED BY Timmy Hu

ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 10 M

No. Freq. (MHz)

Emission Level

(dBuV/m)

Limit (dBuV/m)

Margin (dB)

Antenna Height

(m)

Table Angle

(Degree)

Raw Value

(dBuV)


1 122.78 19.51 QP 30.00 -10.49 1.00 V 82 6.35 13.16 2 131.06 21.30 QP 30.00 -8.70 1.00 V 162 7.63 13.67 3 160.00 19.38 QP 30.00 -10.62 1.00 V 185 4.03 15.35 4 236.20 26.21 QP 37.00 -10.79 1.00 V 0 12.38 13.83 5 366.00 25.19 QP 37.00 -11.81 1.00 V 156 6.90 18.29 6 456.80 24.42 QP 37.00 -12.58 1.00 V 282 3.69 20.73




4.2.8 TEST RESULTS (MODE 2)



28 deg. C, 72 % RH, 1001 hPa


Quasi-Peak,

120kHz

TESTED BY Timmy Hu

ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 10 M

No. Freq. (MHz)

Emission Level

(dBuV/m)

Limit (dBuV/m)

Margin (dB)

Antenna Height

(m)

Table Angle

(Degree)

Raw Value

(dBuV)


1 120.00 20.44 QP 30.00 -9.56 4.00 H 337 7.45 12.99 2 144.00 22.50 QP 30.00 -7.50 4.00 H 216 7.83 14.67 3 240.06 27.19 QP 37.00 -9.81 4.00 H 136 13.19 14.00 4 360.00 26.54 QP 37.00 -10.46 3.29 H 58 8.42 18.12 5 720.00 27.13 QP 37.00 -9.87 1.21 H 348 2.11 25.02 6 960.00 30.03 QP 37.00 -6.97 1.00 H 328 0.39 29.64






28 deg. C, 72 % RH, 1001 hPa


Quasi-Peak,

120kHz

TESTED BY Timmy Hu

ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 10 M

No. Freq. (MHz)

Emission Level

(dBuV/m)

Limit (dBuV/m)

Margin (dB)

Antenna Height

(m)

Table Angle

(Degree)

Raw Value

(dBuV)


1 120.00 23.61 QP 30.00 -6.39 1.00 V 203 10.62 12.99 2 144.00 21.05 QP 30.00 -8.95 1.00 V 40 6.38 14.67 3 239.90 26.27 QP 37.00 -10.73 1.00 V 303 12.28 13.99 4 360.00 25.15 QP 37.00 -11.85 1.00 V 219 7.03 18.12 5 480.40 26.43 QP 37.00 -10.57 1.00 V 188 5.09 21.34 6 720.00 27.09 QP 37.00 -9.91 2.26 V 321 2.07 25.02 7 960.00 30.14 QP 37.00 -6.86 1.66 V 19 0.50 29.64




5 PHOTOGRAPHS OF THE TEST CONFIGURATION

CONDUCTED EMISSION TEST


RADIATED EMISSION TEST (MODE 1)


RADIATED EMISSION TEST (MODE 2)


6 APPENDIX - INFORMATION ON THE TESTING LABORATORIES

We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025.

Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5.phtml. If you have any comments, please feel free to contact us at the following:

Linko EMC/RF Lab: Tel: 886-2-26052180 Fax: 886-2-26052943

Hsin Chu EMC/RF Lab: Tel: 886-3-5935343 Fax: 886-3-5935342

Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050

Email: [email protected] Web Site: www.adt.com.tw

The address and road map of all our labs can be found in our web site also. --- END ---

http://www.adt.com.tw/index.5.phtml

mailto:[email protected]

http://www.adt.com.tw

Page 1

CONSTRUCTION PHOTOS OF EUT

Page 2

Page 3

Documents

VCCI TEST REPORT...Report No.: V110531E05 4 of 27 Report Format Version 4.0.0 1 CERTIFICATION PRODUCT : Remote control Harmony 200 BRAND NAME : Logicool MODEL NO. : N-I0005 APPLICANT