Vauxhall Mokka X Owner's Manual...Radio remote control 3 20, Central locking system 3 23, Electronic key system 3 21, Load compartment 3 28. Seat adjustment Longitudinal adjustment

Vauxhall Mokka XOwner's Manual

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 19Seats, restraints ........................... 38Storage ........................................ 58Instruments and controls ............. 75Lighting ...................................... 114Climate control ........................... 125Driving and operating ................. 132Vehicle care ............................... 176Service and maintenance .......... 216Technical data ........................... 219Customer information ................ 232Index .......................................... 238

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable in the sections "Service andmaintenance" and "Technical data"as well as on the identification plate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.Disregarding the description given inthis manual may affect your warranty.

When this Owner's Manual refers to aworkshop visit, we recommend yourVauxhall Authorised Repairer. Forgas vehicles, we recommend aVauxhall Authorised Repairerlicensed to service gas vehicles.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual● This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to modelvariant, country specifications,special equipment oraccessories.

● The "In brief" section will give youan initial overview.

● The table of contents at thebeginning of this manual andwithin each section shows wherethe information is located.

● The index will enable you tosearch for specific information.

● This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drivevehicles.

● The Owner's Manual uses theengine identifier code. Thecorresponding sales designationand engineering code can befound in the section "Technicaldata".

● Directional data, e.g. left or right,or front or back, always relate tothe direction of travel.

● Displays may not support yourspecific language.

● Display messages and interiorlabelling are written in boldletters.

4 Introduction

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with 3.3 means "see page".Page references and index entriesrefer to the indented headings givenin the section table of content.Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Press c to unlock the doors and loadcompartment. Open the doors bypulling the handles. To open thetailgate, push the touchpad switchbelow the handle.Radio remote control 3 20, Centrallocking system 3 23, Electronic keysystem 3 21, Load compartment3 28.

Seat adjustmentLongitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.Seat position 3 39, Seat adjustment3 40.

In brief 7

Backrest inclination

Pull lever, adjust inclination andrelease lever. Allow the seat toengage audibly.Seat position 3 39, Seat adjustment3 40.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat position 3 39, Seat adjustment3 40.

Seat inclination

Press switchtop : front end higherbottom : front end lower

Seat position 3 39, Seat adjustment3 40.

8 In brief

Head restraint adjustment

Pull the head restraint upwards.Press the catch (1) to release andpush the head restraint downwards.Head restraints 3 38.

Seat belt

Pull out the seat belt and fasten in beltbuckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25°).To unfasten belt, press red button onbelt buckle.Seat position 3 39, Seat belts3 43, Airbag system 3 46.

Mirror adjustmentInterior mirror

To adjust the mirror, move the mirrorhousing in the desired direction.Manual anti-dazzle interior mirror3 32, Automatic anti-dazzle interiormirror 3 33.

In brief 9

Exterior mirrors

Select the relevant exterior mirror andadjust it.Convex exterior mirrors 3 31,Electric adjustment 3 31, Foldingexterior mirrors 3 31, Heatedexterior mirrors 3 32.

Steering wheel adjustment

Unlock the lever, adjust the steeringwheel, then engage the lever andensure it is fully locked.Do not adjust the steering wheelunless the vehicle is stationary andthe steering wheel lock has beenreleased.Airbag system 3 46, Ignitionpositions 3 134.

10 In brief

Instrument panel overview

In brief 11

1 Central locking system .......... 232 Power windows ..................... 343 Exterior mirrors ..................... 314 Light switch ......................... 1145 Cruise control ...................... 151

Speed limiter ....................... 153

Forward collision alert ......... 1546 Side air vents ...................... 1307 Turn and lane-change

signals ................................. 121

Headlight flash .................... 116

Low beam and high beam . . 115

Buttons for DriverInformation Centre ................ 96

8 Instruments ........................... 839 Steering wheel controls ....... 7610 Windscreen wiper,

windscreen washer system ... 77

Rear window wiper, rearwindow washer system ......... 79

11 Centre air vents ................... 13012 Anti-theft alarm system

status LED ........................... 29

13 Info-Display ........................ 10014 Controls for Info-Display

operation ............................. 10015 Glovebox .............................. 5816 Descent control system ......... 93

Fuel selector ......................... 85

Stop-start system ................ 13717 Climate control system ........ 12518 Electronic Stability Control

(ESC) .................................. 14919 Control indicator for airbag

deactivation .......................... 9220 Front storage ......................... 59

Power outlet .......................... 82

USB port, AUX input21 Selector lever, manual

transmission ....................... 145

Selector lever, automatictransmission ....................... 142

22 Parking brake ...................... 14723 Hazard warning flashers .... 12024 Parking assist ..................... 157

Lane departure warning ...... 164

25 Ignition switch withsteering wheel lock ............ 134

Power button ....................... 13426 Horn ..................................... 77

Driver airbag ........................ 4927 Steering wheel adjustment . . 7628 Bonnet release lever .......... 17829 Front storage ......................... 59

Fuse box ............................ 191

12 In brief

Exterior lighting

Turn light switch:m : lights off8 : sidelights9 : low beam

Automatic light controlAUTO : automatic light control:

exterior lighting is switchedon and off automatically

m : activation or deactivation ofthe automatic light control

8 : sidelights9 : low beam

Fog lightsPress light switch:> : front fog lightsø : rear fog light

Lighting 3 114.

Headlight flash, high beam andlow beam

headlight flash : pull leverhigh beam : push leverlow beam : push or pull lever

Automatic light control 3 115, Highbeam 3 115, Headlight flash 3 116,Adaptive forward lighting 3 118.

In brief 13

Turn and lane-change signals

lever up : right turn signallever down : left turn signal

Turn and lane-change signals3 121.

Hazard warning flashers

Operated by pressing ¨.Hazard warning flashers 3 120.

Horn

Press j.

14 In brief

Washer and wiper systemsWindscreen wiper

HI : fastLO : slowINT : interval wiping or automatic

wiping with rain sensorOFF : off

For a single wipe when thewindscreen wiper is off, press thelever down to position 1x.Windscreen wiper 3 77, Wiperblade replacement 3 184.

Windscreen washer system

Pull lever.Windscreen washer system 3 77,Washer fluid 3 181.

Rear window wiper

Press the rocker switch to activate therear window wiper:upper switch : continuous

operationlower switch : intermittent

operationmiddle position : off

In brief 15

Rear window washer

Push lever.Washer fluid is sprayed on the rearwindow and the wiper wipes a fewtimes.Rear window wiper/washer 3 79.

Climate controlHeated rear window, heatedexterior mirrors

The heating is operated by pressingÜ.Heated rear window 3 35.

Demisting and defrosting thewindows

Press V.Set the temperature control to thehighest level.Heated rear window Ü on.Climate control systems 3 125.

16 In brief

TransmissionManual transmission

Reverse: with the vehicle stationary,depress clutch pedal, press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Manual transmission 3 145.

Automatic transmission

P : parkR : reverseN : neutralD : drive

Manual mode: Move selector lever toM.< : higher gear] : lower gear

The selector lever can only be movedout of P when the ignition is on andthe brake pedal is applied. To engageP or R, press the release button.Automatic transmission 3 142.

Starting offCheck before starting off● Tyre pressure and condition

3 195, 3 230.● Engine oil level and fluid levels

3 179.● All windows, mirrors, exterior

lighting and number plates arefree from dirt, snow and ice andare operational.

● Proper position of mirrors, seats,and seat belts 3 31, 3 39,3 44.

● Brake function at low speed,particularly if the brakes are wet.

In brief 17

Starting the engine

● Ignition switch: turn key toposition 2.

Power button: pressEngine Start/Stop for a few

seconds until green LEDilluminates.

● Move the steering wheel slightlyto release the steering wheellock.

● Manual transmission: operateclutch and brake pedal.

● Automatic transmission: operatebrake pedal and move selectorlever to P or N.

● Do not operate accelerator pedal.● Diesel engines: wait until control

indicator ! for preheatingextinguishes.

● Ignition switch: turn key toposition 3 and release.Power button: pressEngine Start/Stop and release.

Starting the engine 3 136.

Stop-start system

If the vehicle is at a low speed or at astandstill and certain conditions arefulfilled, activate an Autostop asfollows:● Depress the clutch pedal.● Shift the selector lever to N.● Release the clutch pedal.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.To restart the engine, depress theclutch pedal again.Stop-start system 3 137.

18 In brief

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the parkingbrake without pressing therelease button. Apply as firmlyas possible on a downhill slopeor uphill slope. Depress brakepedal at the same time toreduce operating force.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear or set the selectorlever to position P beforeremoving the ignition key. Onan uphill slope, turn the frontwheels away from the kerb.If the vehicle is on a downhillslope, engage reverse gear or

set the selector lever to positionP before removing the ignitionkey. Turn the front wheelstowards the kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch. For vehicleswith automatic transmission,the key can only be removedwhen the selector lever is inposition P.Turn the steering wheel untilthe steering wheel lock is felt toengage.

● Lock the vehicle with e on theradio remote control.Activate the anti-theft alarmsystem 3 29.

● The engine cooling fans may runafter the engine has beenswitched off 3 178.

Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a lowload or run in neutral for approx.30 seconds before switching off, inorder to protect the turbocharger.

Keys, locks 3 19, Laying the vehicleup for a long period of time 3 177.

Keys, doors and windows 19

Keys, doors andwindows

Keys, locks ................................... 19Keys .......................................... 19Radio remote control ................. 20Electronic key system ................ 21Memorised settings ................... 23Central locking system .............. 23Delayed locking ......................... 26Automatic locking ...................... 27Child locks ................................. 28

Doors ........................................... 28Load compartment .................... 28

Vehicle security ............................ 29Anti-theft locking system ........... 29Anti-theft alarm system .............. 29Immobiliser ................................ 30

Exterior mirrors ............................ 31Convex shape ........................... 31Electric adjustment .................... 31Folding mirrors .......................... 31Heated mirrors ........................... 32

Interior mirrors ............................. 32Manual anti-dazzle .................... 32Automatic anti-dazzle ................ 33

Windows ...................................... 33Windscreen ............................... 33Manual windows ........................ 33Power windows ......................... 34Heated rear window .................. 35Sun visors .................................. 35

Roof ............................................. 36Sunroof ...................................... 36

Keys, locksKeys

Caution

Do not attach heavy or bulky itemsto the ignition key.

Replacement keysThe key number is specified on adetachable tag.The key number must be quotedwhen ordering replacement keys as itis a component of the immobilisersystem.Locks 3 213, Central locking 3 23,Starting the engine 3 136.Radio remote control 3 20.Electronic key 3 21.The code number of the adapter forthe locking wheel nuts is specified ona card. It must be quoted whenordering a replacement adapter.

20 Keys, doors and windows

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Radio remote control

Enables operation of the followingfunctions via the use of the remotecontrol buttons:● central locking system 3 23● anti-theft locking system 3 29● anti-theft alarm system 3 29

The radio remote control has a rangeof approx. 30 metres. It can berestricted by external influences. Thehazard warning flashers confirmoperation.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

Radio remote control batteryreplacementReplace the battery as soon as therange reduces.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.


Extend the key and open the unit.Replace the battery (battery typeCR 2032), paying attention to theinstallation position. Close the unitand synchronise.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control issynchronised when the ignition isswitched on.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, it may be due to the following:● The range is exceeded.● The battery voltage is too low.● Frequent, repeated operation of

the radio remote control while notin range, which will require re-synchronisation.

● Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time.

● Interference from higher-powerradio waves from other sources.

Electronic key system

Enables a keyless operation of thefollowing functions:● central locking system 3 23● starting the engine 3 136

The electronic key simply needs to beon the driver's person.

Additionally, the electronic keyincludes the functionality of the radioremote control 3 20.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.NoticeDo not put the electronic key in theload compartment or in front of theInfo-Display.

Replacing battery in electronickeyReplace the battery as soon as thesystem no longer operates properlyor the range is reduced. The need forbattery replacement is indicated by amessage in the Driver InformationCentre 3 102.


Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.To replace:

1. Press button at the back of theelectronic key unit and extract thekey blade from the housing.

2. Insert the key blade approx. 6 mminto the housing and turn the keyto open the housing. Furtherinsertion of the key blade candamage the housing.

3. Remove and replace battery. UseCR 2032 or equivalent battery.Pay attention to the installationposition.

4. Close the housing and insert keyblade.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

Electronic key synchronisationThe electronic key synchronises itselfautomatically during every startingprocedure.

FaultIf the central locking cannot beoperated or the engine cannot bestarted, the cause may be one of thefollowing:● Fault in electronic key.● Electronic key is out of reception

range.● The battery voltage is too low.● Overload of the central locking

system by operating at frequentintervals, the power supply isinterrupted for a short time.

● Interference from higher-powerradio waves from other sources.

To rectify the cause of the fault,change the position of the electronickey.Manual unlocking 3 23.


Memorised settingsWhenever the ignition is switched off,the following settings may beautomatically memorised by theremote control unit or the electronickey:● lighting● Infotainment system● central locking system● comfort settings

A precondition is that Personalizationby driver is activated in the personalsettings of the Info-Display. This mustbe set for each remote control unit orelectronic key which is used.Vehicle personalisation 3 104.

Central locking systemUnlocks and locks doors, loadcompartment and fuel filler flap.A pull on an interior door handleunlocks the respective door. Pullingthe handle again opens the door.

NoticeIn the event of an accident in whichairbags or belt pretensioners aredeployed, the vehicle isautomatically unlocked.NoticeA short time after unlocking with theremote control the doors are lockedautomatically if no door has beenopened. A precondition is that thesetting is activated in the vehiclepersonalisation 3 104.

Remote control operation

Unlocking

Press c.

Unlocking mode can be set in thevehicle personalisation menu in theInfo-Display. Two settings areselectable:● All doors, load compartment and

fuel filler flap will be unlocked bypressing c once.

● Only the driver's door, loadcompartment and fuel filler flapwill be unlocked by pressing conce. To unlock all doors, pressc twice.

Select the relevant setting in thesettings menu in the Info-Display.Vehicle personalisation 3 104.The setting can be saved for theremote control being used.Memorised settings 3 23.

LockingClose doors, load compartment andfuel filler flap.


Press e.If the driver's door is not closedproperly, the central locking systemwill not work.

ConfirmationOperation of the central lockingsystem is confirmed by the hazardwarning flashers. A precondition isthat the setting is activated in thevehicle personalisation 3 104.

Electronic key system operation

The electronic key must be outsidethe vehicle, within a range of approx.one metre of the relevant door side.

Unlocking

Press the button on the respectiveexterior door handle and pull thehandle.Unlocking mode can be set in thevehicle personalisation menu in theInfo-Display. Two settings areselectable:● All doors, load compartment and

fuel filler flap will be unlocked bypressing the button on anyexterior handle once.

● Only the driver's door, loadcompartment and fuel filler flapwill be unlocked by pressing the


button on the driver`s doorexterior handle once. To unlockall doors, press button twice.

The setting can be changed in thesettings menu in the Info-Display.Vehicle personalisation 3 104.

Locking

Press the button on any exterior doorhandle.All doors, load compartment and fuelfiller flap will be locked.

The system locks if any of thefollowing occurs:● It has been more than

five seconds since unlocking.● The button on an exterior handle

has been pressed twice withinfive seconds to unlock thevehicle.

● Any door has been opened andall doors are now closed.

If the driver's door is not closedproperly, the electronic key remains inthe vehicle or the ignition is still on,locking will not be permitted and awarning chime sounds three times.If there have been two or moreelectronic keys in the vehicle and theignition was on once, the doors will belocked even if just one electronic keyis taken out of the vehicle.

Unlocking and opening the tailgateThe tailgate and the doors can beunlocked by pressing the buttonunder the tailgate moulding when theelectronic key is in range.

Operation with buttons on theelectronic key

The central locking system can alsobe operated with the buttons on theelectronic key.Press c to unlock.Press e to lock.Remote control operation 3 23.

Passive lockingAutomatic locking 3 27.


ConfirmationOperation of central locking system isconfirmed by the hazard warningflashers. A precondition is that thesetting is activated in the vehiclepersonalisation 3 104.

Central locking buttonsLocks or unlocks all doors, the loadcompartment and fuel filler flap fromthe passenger compartment via aswitch in the driver's door panel.

Press e to lock.Press c to unlock.

Operation with the key in case ofa central locking system faultIn case of a fault, e.g. vehicle batteryor remote control/electronic keybattery is discharged, the driver'sdoor can be locked or unlocked withthe mechanical key.

Manual unlocking

Manually unlock the driver's door byinserting and turning the key in thelock cylinder.

The other doors can be opened bypulling the interior handle twice or bypressing c in the driver's door panel.The load compartment and fuel fillerflap will possibly not be unlocked.By switching on the ignition, the anti-theft locking system is deactivated.

Manual lockingPush inside locking knob of all doorsexcept driver's door or press e in thedriver's door panel. Then close thedriver's door and lock it from theoutside by turning the key in the lockcylinder. The fuel filler flap andtailgate are possibly not locked.

Delayed lockingThis feature will delay the actuallocking of the doors and arming of theanti-theft alarm system forfive seconds when the power doorlock switch or radio remote control isused to lock the vehicle.This can be changed in the vehiclesettings.Vehicle personalisation 3 104.


ON: When pressing the centrallocking button, three chimes willsound to signal delayed locking isactivated.The doors will not lock untilfive seconds after the last door isclosed. You can temporarily overridedelayed locking by pressing thecentral locking button or the lockingbutton on the radio remote control.OFF: The doors will lock immediatelywhen pressing the power lock switchor e on the radio remote control.

Automatic lockingAutomatic locking after driving offThis security feature can beconfigured to automatically lock alldoors, load compartment and fuelfiller flap after driving off andexceeding a certain speed.When at a standstill after driving, thevehicle will be unlocked automaticallyas soon as the key is removed fromthe ignition switch, or with electronickey system when the ignition isswitched off.

Activation or deactivation ofautomatic locking can be set in thesettings menu in the Info-Display.Info-Display 3 100.Vehicle personalisation 3 104.The setting can be saved for theremote control or electronic key beingused 3 23.

Automatic relock after unlockingThis feature can be configured toautomatically lock all doors, loadcompartment and fuel filler flap ashort time after unlocking with theremote control or electronic key,provided no door has been opened.Activation or deactivation ofautomatic relock can be set in thesettings menu in the Info-Display.Info-Display 3 100.Vehicle personalisation 3 104.The setting can be saved for theremote control or electronic key beingused 3 23.

Passive lockingOn vehicles with electronic keysystem, this feature locks the vehicleautomatically after several seconds ifan electronic key has beenrecognised previously inside thevehicle, all doors have then beenclosed and the electronic key doesnot remain within the vehicle.If the electronic key remains in thevehicle or the ignition is still on,passive locking will not be permitted.If there have been two or moreelectronic keys in the vehicle and theignition was on once, the featurelocks the vehicle if just one electronickey is taken out of the vehicle.Passive locking can be disabled bypressing c for a few seconds whileone door is open. It remains disableduntil e is pressed or the ignition isswitched on.Activation or deactivation of passivelocking can be set in the settingsmenu in the Info-Display.Info-Display 3 100.Vehicle personalisation 3 104.


The setting can be saved for theelectronic key being used 3 23.

Child locks

9 Warning

Use the child locks wheneverchildren are occupying the rearseats.

Using a key or suitable screwdriver,turn the child lock in the rear door tothe horizontal position. The doorcannot be opened from the inside. Fordeactivation turn the child lock to thevertical position.

DoorsLoad compartmentTailgate

Opening

After unlocking, push the touchpadswitch and open the tailgate.

ClosingUse one of the interior handles.Do not push the touchpad switch orthe brand emblem whilst closing asthis will unlock the tailgate again.Central locking system 3 23.

General hints for operatingtailgate

9 Danger

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, since toxic exhaustgases, which cannot be seen orsmelled, could enter the vehicle.This can cause unconsciousnessand even death.

Caution

Before opening the tailgate, checkoverhead obstructions, e.g. agarage door, to avoid damage tothe tailgate. Always check themoving area above and behind thetailgate.

NoticeThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.


Vehicle securityAnti-theft locking system

9 Warning

Do not use the system if there arepeople in the vehicle! The doorscannot be unlocked from theinside.

The system deadlocks all the doors.All doors must be closed otherwisethe system cannot be activated.Unlocking the vehicle disables themechanical anti-theft locking system.This is not possible with the centrallocking button.

Activating

Press e on the radio remote controltwice within five seconds.

Anti-theft alarm systemThe anti-theft alarm system iscombined with the central lockingsystem.It monitors:● doors, load compartment, bonnet● ignition

Unlocking the vehicle deactivates theanti-theft alarm system.

ActivationAll doors must be closed and theelectronic key of the electronic keysystem must not remain in thevehicle. Otherwise the system cannotbe activated.● Radio remote control: self-

activated 30 seconds afterlocking the vehicle by pressing eonce.

● Electronic key system: self-activated 30 seconds afterlocking the vehicle by pressingthe button on any exterior doorhandle.

● Radio remote control orelectronic key: directly bypressing e twice withinfive seconds.

● Electronic key system withpassive locking enabled: brieflyactivated after passive lockingoccurs.


NoticeChanges to the vehicle interior, e.g.the use of seat covers, and openwindows, could impair the functionof passenger compartmentmonitoring.

Status LED

Status LED is integrated in the sensoron top of the instrument panel.Status during the first 30 seconds ofanti-theft alarm system activation:LED illuminates : test, arming delayLED flashesquickly

: doors, tailgate orbonnet notcompletely closed,or system fault

Status after system is armed:LED flashesslowly

: system is armed

Seek the assistance of a workshop inthe event of faults.

DeactivationRadio remote control: Unlocking thevehicle by pressing c deactivates theanti-theft alarm system.Electronic key system: Unlocking thevehicle by pressing the button on anyexterior door handle deactivates theanti-theft alarm system.The electronic key must be outsidethe vehicle, within a range of approx.one metre of the relevant door side.The system is not deactivated byunlocking the driver's door with thekey or with the central locking buttonin the passenger compartment.

AlarmThe alarm can be silenced bypressing any button on the radioremote control or by switching on theignition.

The anti-theft alarm system can bedeactivated by pressing e orswitching on the ignition.

ImmobiliserThe system is part of the ignitionswitch and checks whether thevehicle is allowed to be started withthe key being used.The immobiliser is activatedautomatically after the key has beenremoved from the ignition switch.If the control indicator d flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and repeat thestart attempt.If the control indicator continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.


NoticeThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it and switch onthe anti-theft alarm system 3 23,3 29.

Control indicator d 3 94.

Exterior mirrorsConvex shapeThe convex exterior mirror containsan aspherical area and reduces blindspots. The shape of the mirror makesobjects appear smaller, which willaffect the ability to estimatedistances.

Electric adjustment

Select the relevant exterior mirror byturning the control to left (L) or right(R). Then swivel the control to adjustthe mirror.

In position 0 no mirror is selected.

Folding mirrorsManual folding

For pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.


Electric folding

Turn control to 0, then push thecontrol backwards. Both exteriormirrors will fold in.Push the control backwards again -both exterior mirrors return to theiroriginal position.

Heated mirrors

Operated by pressing Ü.Heating functions with the enginerunning and is switched offautomatically after a short time.

Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing.


Automatic anti-dazzle

Dazzle from following vehicles atnight is automatically reduced.

WindowsWindscreenHeat-reflecting windscreenThe heat-reflecting windscreen has acoating which reflects solar radiation.Also data signals, e.g. from tollstations, might be reflected.

The marked areas of the windscreenbehind the interior mirror are notcovered with the coating. Devices forelectronic data recording and feepayment must be attached in theseareas. Otherwise data recordingmalfunctions may occur.

Windscreen stickersDo not attach stickers such as tollroad stickers or similar on thewindscreen in the area of the interiormirror. Otherwise the detection zoneof the sensor and the view area of thecamera in the mirror housing could berestricted.

Windscreen replacement

Caution

If the vehicle has a front-lookingcamera sensor for the driverassistance systems, it is veryimportant that any windscreenreplacement is performedaccurately according to Vauxhallspecifications. Otherwise, thesesystems may not work properlyand there is a risk of unexpectedbehaviour and/or messages fromthese systems.

Manual windowsThe door windows can be opened orclosed with the window cranks.


Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.If there are children on the rearseats, switch on the child safetysystem for the power windows.Keep a close watch on thewindows when closing them.Ensure that nothing becomestrapped in them as they move.

Switch on ignition to operate powerwindows.

Operate the switch for the respectivewindow by pushing to open or pullingto close.Pushing or pulling gently to the firstdetent: window moves up or down aslong as the switch is operated.Pushing or pulling firmly to the seconddetent and then releasing: windowmoves up or down automatically withsafety function enabled. To stopmovement, operate the switch oncemore in the same direction.

Safety functionIf the window glass encountersresistance above the middle of thewindow during automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, switch on theignition, then pull the switch to the firstdetent and hold. The window movesup without safety function enabled.To stop movement, release theswitch.


Child safety system for rearwindows

Press z to deactivate rear powerwindows.To activate, press z again.

OverloadIf the windows are repeatedlyoperated within short intervals, thewindow operation is disabled forsome time.

Initialising the power windowsIf the windows cannot be closedautomatically (e.g. afterdisconnecting the vehicle battery),activate the window electronics asfollows:1. Close doors.2. Switch on ignition.3. Pull switch until the window is

closed and keep pulling foradditional two seconds.

4. Repeat for each window.

Heated rear window

Operated by pressing Ü.

The LED in the button indicatesactivation.Heating works with the enginerunning and is switched offautomatically after a short time.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.The sun visors mirror covers shouldbe closed when driving.If the sun visors have a vanity mirrorlamp, the lamp will illuminate whenopening the vanity mirror cover.


RoofSunroof

9 Warning

Take care when operating thesunroof. Risk of injury, particularlyto children.Keep a close eye on the movableparts when operating them.Ensure that nothing becomestrapped in them as they move.

Switch on ignition to operate thesunroof.

Open or closePress switch 1 or switch 2 gently tothe first detent: sunroof is opened orclosed as long as the switch isoperated.Press switch 1 or switch 2 firmly to thesecond detent and then release: thesunroof is opened or closedautomatically with safety functionenabled. To stop movement, operatethe switch once more.

Raise or closePress switch 3 or switch 4: sunroof israised or closed automatically withsafety function enabled.If the sunroof is raised, it can beopened in one step by pressingswitch 1.

SunblindThe sunblind is operated manually.Close or open the sunblind by sliding.When the sunroof is open, thesunblind is always open.

Dirt and debris may collect on thesunroof seal or in the track that couldcause an issue with sunroofoperation, noise or plug the waterdrainage system. Periodically openthe sunroof and remove anyobstacles or loose debris. Wipe thesunroof seal and roof sealing areausing a clean cloth, mild soap, andwater. Do not remove grease from thesunroof.

General hints

Safety functionIf the sunroof encounters resistanceduring automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, press and holdswitch 2. The sunroof closes withoutsafety function enabled. To stopmovement, release the switch.


Initialising after a power failureAfter a power failure, it may only bepossible to operate the sunroof to alimited extent. Have the systeminitialised by your workshop.

38 Seats, restraints

Seats, restraints

Head restraints ............................ 38Front seats ................................... 39

Seat position .............................. 39Seat adjustment ........................ 40Heating ...................................... 42

Seat belts ..................................... 43Three-point seat belt ................. 44

Airbag system .............................. 46Front airbag system ................... 49Side airbag system .................... 49Curtain airbag system ............... 50Airbag deactivation .................... 51

Child restraints ............................. 52Child restraint systems .............. 52Child restraint installationlocations ................................... 53

ISOFIX child restraint systems . . 56Top-tether fastening eyes .......... 57

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

Adjustment

Head restraints on front seats

Height adjustmentPull the head restraint upwards.To move down, press the catch (1)and push the head restraintdownwards.

RemovingRaise head restraint to its full height.Press the catches (1) and (2) at thesame time.Pull up the head restraint.

Seats, restraints 39

Horizontal adjustment

To adjust horizontally, pull the headrestraint forwards. It engages in threepositions.To return to its rearmost position, pullfully forwards and release.

Head restraints on rear seats

Height adjustmentPull the head restraint upwards.To move down, press the catch (1)and push the head restraintdownwards.

RemovalRaise head restraint to its full height.Press the catches (1) and (2) at thesame time.Pull up the head restraint.

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

9 Warning

Never store any objects under theseats.


● Sit with buttocks as far backagainst the backrest as possible.Adjust the distance between theseat and the pedals so that legsare slightly angled when fullypressing the pedals. Slide thefront passenger seat as far backas possible.

● Set seat height high enough tohave a clear field of vision on allsides and of all displayinstruments. There should be atleast one hand of clearancebetween head and theheadlining. Your thighs shouldrest lightly on the seat withoutpressing into it.

● Sit with shoulders as far backagainst the backrest as possible.Set the backrest rake so that it ispossible to easily reach thesteering wheel with arms slightlybent. Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Donot tilt the backrest too far back.We recommend a maximum rakeof approx. 25°.

● Adjust seat and steering wheel ina way that the wrist rests on topof the steering wheel while thearm is fully extended andshoulders on the backrest.

● Adjust the steering wheel 3 76.● Adjust the head restraint 3 38.● Adjust the height of the seat belt

3 44.● Adjust the thigh support so that

there is a space approx. twofingers wide between the edge ofthe seat and the hollow of theknee.

● Adjust the lumbar support so thatit supports the natural shape ofthe spine.

Seat adjustmentDrive only with engaged seats andbackrests.

Longitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.


Backrest inclination

Pull lever, adjust inclination andrelease lever. Allow the backrest toengage audibly.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat inclination

Press switchtop : front end higherbottom : front end lower


Lumbar support

Adjust lumbar support using the four-way switch to suit personalrequirements.Moving support up and down: pushswitch up or down.Increasing and decreasing support:push switch forwards or backwards.

Adjustable thigh support

Pull the lever and slide the thighsupport.

Heating

Adjust heating to the desired settingby pressing ß for the respective seatone or more times. The LED in thebutton indicates the setting.Prolonged use of the highest settingfor people with sensitive skin is notrecommended.Seat heating is operational whenengine is running and during anAutostop.Stop-start system 3 137.


Seat belts

The seat belts are locked duringheavy acceleration or deceleration ofthe vehicle, holding the occupants inthe seat position. Therefore the risk ofinjury is considerably reduced.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. Childrestraint system 3 52.Periodically check all parts of the beltsystem for damage, soiling andproper functionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt pretensionersreplaced by a workshop.NoticeMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or are trapped. Prevent dirtfrom getting into the belt retractors.

Seat belt reminder X 3 91.

Belt force limitersOn the front seats, stress on the bodyis reduced by the gradual release ofthe belt during a collision.

Belt pretensionersIn the event of a head-on or rear-endcollision of a certain severity, the frontseat belts are tightened.

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the beltpretensioners.

Deployment of the belt pretensionersis indicated by continuous illuminationof control indicator v 3 91.Triggered belt pretensioners must bereplaced by a workshop. Beltpretensioners can only be triggeredonce.NoticeDo not affix or install accessories orother objects that may interfere withthe operation of the beltpretensioners. Do not make anymodifications to belt pretensionercomponents as this will invalidatethe vehicle type approval.


Three-point seat beltFasten

Withdraw the belt from the retractor,guide it untwisted across the bodyand insert the latch plate into thebuckle.Tighten the lap belt regularly whilstdriving by pulling the shoulder belt.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Height adjustment

1. Pull belt out slightly.2. Shift the height adjuster upwards

or press button to disengage andpush the height adjusterdownwards.


Adjust the height so that the belt liesacross the shoulder. It must not lieacross the throat or upper arm.

9 Warning

Do not adjust while driving.

Unfasten

To release belt, press red button onbelt buckle.

Seat belts on the rear seatsThe seat belt for the rear centre seatcan only be withdrawn from theretractor if the backrest is engaged inupright position.

Using seat belt during pregnancy

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.


Airbag systemThe airbag system consists of anumber of individual systemsdepending on the scope ofequipment.When triggered, the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly the airbagsystems can be triggered in anexplosive manner.

NoticeThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not affix any objects onto theairbag covers and do not cover themwith other materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it may be

necessary to have the steeringwheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate, escapinghot gases may cause burns.Control indicator v for airbag systems3 91.

Child restraint systems on frontpassenger seat with airbagsystemsWarning according to ECE R94.02:

EN: NEVER use a rearward-facingchild restraint on a seat protected byan ACTIVE AIRBAG in front of it;DEATH or SERIOUS INJURY to theCHILD can occur.DE: Nach hinten gerichteteKindersitze NIEMALS auf einem Sitzverwenden, der durch einen davorbefindlichen AKTIVEN AIRBAGgeschützt ist, da dies den TOD oderSCHWERE VERLETZUNGEN DESKINDES zur Folge haben kann.FR: NE JAMAIS utiliser un sièged'enfant orienté vers l'arrière sur unsiège protégé par un COUSSINGONFLABLE ACTIF placé devant lui,sous peine d'infliger desBLESSURES GRAVES, voireMORTELLES à l'ENFANT.ES: NUNCA utilice un sistema deretención infantil orientado haciaatrás en un asiento protegido por unAIRBAG FRONTAL ACTIVO. Peligrode MUERTE o LESIONES GRAVESpara el NIÑO.RU: ЗАПРЕЩАЕТСЯустанавливать детскоеудерживающее устройство лицомназад на сиденье автомобиля,


оборудованном фронтальнойподушкой безопасности, еслиПОДУШКА НЕ ОТКЛЮЧЕНА! Этоможет привести к СМЕРТИ илиСЕРЬЕЗНЫМ ТРАВМАМРЕБЕНКА.NL: Gebruik NOOIT een achterwaartsgericht kinderzitje op een stoel meteen ACTIEVE AIRBAG ervoor, omDODELIJK of ERNSTIG LETSEL vanhet KIND te voorkomen.DA: Brug ALDRIG en bagudvendtautostol på et forsæde med AKTIVAIRBAG, BARNET kan komme iLIVSFARE eller komme ALVORLIGTTIL SKADE.SV: Använd ALDRIG en bakåtvändbarnstol på ett säte som skyddas meden framförvarande AKTIV AIRBAG.DÖDSFALL eller ALLVARLIGASKADOR kan drabba BARNET.FI: ÄLÄ KOSKAAN sijoita taaksepäinsuunnattua lasten turvaistuintaistuimelle, jonka edessä onAKTIIVINEN TURVATYYNY, LAPSIVOI KUOLLA tai VAMMAUTUAVAKAVASTI.

NO: Bakovervendtbarnesikringsutstyr må ALDRI brukespå et sete med AKTIVKOLLISJONSPUTE foran, da det kanføre til at BARNET utsettes forLIVSFARE og fare for ALVORLIGESKADER.PT: NUNCA use um sistema deretenção para crianças voltado paratrás num banco protegido com umAIRBAG ACTIVO na frente domesmo, poderá ocorrer a PERDA DEVIDA ou FERIMENTOS GRAVES naCRIANÇA.IT: Non usare mai un sistema disicurezza per bambini rivoltoall'indietro su un sedile protetto daAIRBAG ATTIVO di fronte ad esso:pericolo di MORTE o LESIONIGRAVI per il BAMBINO!EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικόκάθισμα ασφαλείας με φορά προς ταπίσω σε κάθισμα που προστατεύεταιαπό μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,διότι το παιδί μπορεί να υποστείΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟΤΡΑΥΜΑΤΙΣΜΟ.

PL: NIE WOLNO montować fotelikadziecięcego zwróconego tyłem dokierunku jazdy na fotelu, przedktórym znajduje się WŁĄCZONAPODUSZKA POWIETRZNA.Niezastosowanie się do tegozalecenia może być przyczynąŚMIERCI lub POWAŻNYCHOBRAŻEŃ u DZIECKA.TR: Arkaya bakan bir çocuk emniyetsistemini KESİNLİKLE önünde birAKTİF HAVA YASTIĞI ilekorunmakta olan bir koltuktakullanmayınız. ÇOCUK ÖLEBİLİRveya AĞIR ŞEKİLDEYARALANABİLİR.UK: НІКОЛИ не використовуйтесистему безпеки для дітей, щовстановлюється обличчям назад,на сидінні з УВІМКНЕНОЮПОДУШКОЮ БЕЗПЕКИ, інакше цеможе призвести до СМЕРТІ чиСЕРЙОЗНОГО ТРАВМУВАННЯДИТИНИ.HU: SOHA ne használjon hátrafelénéző biztonsági gyerekülést előlrőlAKTÍV LÉGZSÁKKAL védett ülésen,mert a GYERMEK HALÁLÁT vagyKOMOLY SÉRÜLÉSÉT okozhatja.


HR: NIKADA nemojte koristiti sustavzadržavanja za djecu okrenut premanatrag na sjedalu s AKTIVNIMZRAČNIM JASTUKOM ispred njega,to bi moglo dovesti do SMRTI iliOZBILJNJIH OZLJEDA za DIJETE.SL: NIKOLI ne nameščajte otroškegavarnostnega sedeža, obrnjenega vnasprotni smeri vožnje, na sedež zAKTIVNO ČELNO ZRAČNOBLAZINO, saj pri tem obstajanevarnost RESNIH ali SMRTNIHPOŠKODB za OTROKA.SR: NIKADA ne koristiti bezbednosnisistem za decu u kome su decaokrenuta unazad na sedištu saAKTIVNIM VAZDUŠNIMJASTUKOM ispred sedišta zato štoDETE može da NASTRADA ili da seTEŠKO POVREDI.MK: НИКОГАШ не користете детскоседиште свртено наназад наседиште заштитено со АКТИВНОВОЗДУШНО ПЕРНИЧЕ пред него,затоа што детето може ДА ЗАГИНЕили да биде ТЕШКО ПОВРЕДЕНО.BG: НИКОГА не използвайтедетска седалка, гледаща назад,върху седалка, която е защитена

чрез АКТИВНА ВЪЗДУШНАВЪЗГЛАВНИЦА пред нея - може дасе стигне до СМЪРТ илиСЕРИОЗНО НАРАНЯВАНЕ наДЕТЕТО.RO: Nu utilizaţi NICIODATĂ un scaunpentru copil îndreptat spre partea dinspate a maşinii pe un scaun protejatde un AIRBAG ACTIV în faţa sa;acest lucru poate duce la DECESULsau VĂTĂMAREA GRAVĂ aCOPILULUI.CS: NIKDY nepoužívejte dětskýzádržný systém instalovaný protisměru jízdy na sedadle, které jechráněno před sedadlem AKTIVNÍMAIRBAGEM. Mohlo by dojít kVÁŽNÉMU PORANĚNÍ nebo ÚMRTÍDÍTĚTE.SK: NIKDY nepoužívajte detskúsedačku otočenú vzad na sedadlechránenom AKTÍVNYM AIRBAGOM,pretože môže dôjsť k SMRTI aleboVÁŽNYM ZRANENIAM DIEŤAŤA.LT: JOKIU BŪDU nemontuokite atgalatgręžtos vaiko tvirtinimo sistemossėdynėje, prieš kurią įrengta AKTYVIORO PAGALVĖ, nes VAIKAS GALIŽŪTI arba RIMTAI SUSIŽALOTI.

LV: NEKĀDĀ GADĪJUMĀneizmantojiet uz aizmuguri vērstubērnu sēdeklīti sēdvietā, kas tiekaizsargāta ar tās priekšā uzstādītuAKTĪVU DROŠĪBAS SPILVENU, jopretējā gadījumā BĒRNS var gūtSMAGAS TRAUMAS vai IET BOJĀ.ET: ÄRGE kasutage tahapoolesuunatud lapseturvaistet istmel, milleees on AKTIIVSE TURVAPADJAGAkaitstud iste, sest see võibpõhjustada LAPSE SURMA võiTÕSISE VIGASTUSE.MT: QATT tuża trażżin għat-tfal lijħares lejn in-naħa ta’ wara fuq sitprotett b’AIRBAG ATTIV quddiemu;dan jista’ jikkawża l-MEWT jewĠRIEĦI SERJI lit-TFAL.Beyond the warning required byECE R94.02, for safety reasonsnever use a forward-facing childrestraint system on the passengerseat with an active front airbag.

9 Danger

Do not use a child restraint systemon the passenger seat with activefront airbag.


The warning label is located on bothsides of the front passenger sun visor.Airbag deactivation 3 51.

Front airbag systemThe front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. These can beidentified by the word AIRBAG.The front airbag system is triggered inthe event of a front-end impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and head ofthe front seat occupantsconsiderably.

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position.Seat position 3 39.Keep the area in which the airbaginflates clear of obstructions.Fit the seat belt correctly andengage securely. Only then is theairbag able to protect.

Side airbag system

The side airbag system consists of anairbag in each front seat backrest.This can be identified by the wordAIRBAG.The side airbag system is triggered inthe event of a side impact of a certainseverity. The ignition must beswitched on.


The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and pelvis inthe event of a side-on collisionconsiderably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoticeOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Curtain airbag systemThe curtain airbag system consists ofan airbag in the roof frame on eachside. This can be identified by theword AIRBAG on the roof pillars.

The curtain airbag system is triggeredin the event of a side-on impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the head in the event of aside-on impact considerably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks in the roof frame areonly suitable for hanging up lightarticles of clothing, without coathangers. Do not keep any items inthese clothes.


Airbag deactivationThe front passenger airbag systemmust be deactivated if a child restraintsystem is to be fitted on this seat. Theside airbag and curtain airbagsystems, the belt pretensioners andall driver airbag systems will remainactive.

The front passenger airbag systemcan be deactivated via a key-operated switch on the passengerside of the instrument panel.

Use the ignition key to choose theposition:c : front passenger airbags are

deactivated and will not inflatein the event of a collision.Control indicator cilluminates continuously in thecentre console. A childrestraint system can beinstalled in accordance withthe chart Child restraintinstallation locations 3 53.No adult person is allowed tooccupy the front passengerseat.

d : front passenger airbags areactive. A child restraint systemmust not be installed.

9 Danger

Risk of fatal injury for a child usinga child restraint system on a seatwith activated front passengerairbag.Risk of fatal injury for an adultperson on a seat with deactivatedfront passenger airbag.

As long as the control indicator c isnot illuminated, the front passengerairbag system will inflate in the eventof a collision.Change status only when the vehicleis stopped with the ignition off.Status remains until the next change.Control indicator for airbagdeactivation 3 92.


Child restraintsChild restraint systemsWe recommend the Vauxhall childrestraint system which is tailoredspecifically to the vehicle.When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.

9 Warning

When using a child restraintsystem on the front passengerseat, the airbag systems for thefront passenger seat must bedeactivated; if not, the triggering ofthe airbags poses a risk of fatalinjury to the child.This is especially the case if rear-facing child restraint systems areused on the front passenger seat.

Airbag deactivation 3 51.Airbag label 3 46.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This ensures that the child'sbackbone, which is still very weak, isunder less strain in the event of anaccident.Suitable are restraint systems thatcomply with valid UN ECEregulations. Check local laws andregulations for mandatory use of childrestraint systems.Ensure that the child restraint systemto be installed is compatible with thevehicle type.Ensure that the mounting location ofthe child restraint system within thevehicle is correct, see followingtables.Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.

When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.NoticeDo not affix anything on the childrestraint systems and do not coverthem with any other materials.A child restraint system which hasbeen subjected to stress in anaccident must be replaced.


Child restraint installation locationsPermissible options for fitting a child restraint system

Weight classOn front passenger seat

On rear outboard seats On rear centre seatactivated airbag deactivated airbag

Group 0: up to 10 kg X U1 U2 U2

Group 0+: up to 13 kg X U1 U2 U2

Group I: 9 to 18 kg X U1 U2 U2

Group II: 15 to 25 kg X X U2 U2

Group III: 22 to 36 kg X X U2 U2

1 : if the child restraint system is being secured using a three-point seat belt, move seat height adjustment to uppermostposition and ensure that vehicle seat belt runs forwards from the upper anchorage point. Adjust seat backrestinclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle side.

2 : move the head restraint to uppermost position. If it interferes with the proper installation of the child restraint system,remove the head restraint 3 38.

U : universal suitability in conjunction with three-point seat belt.X : no child restraint system permitted in this weight class.


Permissible options for fitting an ISOFIX child restraint system

Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat

Group 0: up to 10 kg E ISO/R1 X IL1 X

Group 0+: up to 13 kg E ISO/R1 X IL1 X

D ISO/R2 X IL1 X

C ISO/R3 X IL1 X

Group I: 9 to 18 kg D ISO/R2 X IL1 X

C ISO/R3 X IL1 X

B ISO/F2 X IL, IUF X

B1 ISO/F2X X IL, IUF X

A ISO/F3 X IL, IUF X

Group II: 15 to 25 kg X IL X

Group III: 22 to 36 kg X IL X

1 : move front passenger seat to the foremost position or adjust front seat backrest inclination as far as necessary toa vertical position to ensure that there is no interference between child restraint system and front seat backrest.

IL : suitable for particular ISOFIX restraint systems of the "specific-vehicle", "restricted" or "semi-universal" categories.The ISOFIX restraint system must be approved for the specific vehicle type.

IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class.X : no ISOFIX child restraint system approved in this weight class.


ISOFIX size class and seat deviceA – ISO/F3 : forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kgB – ISO/F2 : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgB1 – ISO/F2X : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgC – ISO/R3 : rear-facing child restraint system for children of maximum size in the weight class up to 18 kgD – ISO/R2 : rear-facing child restraint system for smaller children in the weight class up to 18 kgE – ISO/R1 : rear-facing child restraint system for young children in the weight class up to 13 kg


ISOFIX child restraintsystemsInstallation of ISOFIX childrestraint systems withoutpermanent guide

Fasten vehicle-approved ISOFIXchild restraint systems to the ISOFIXmounting brackets. Specific vehicleISOFIX child restraint systempositions are marked in the table byIL.

ISOFIX mounting brackets areindicated by a label on the backrest.

Installation of ISOFIX childrestraint systems with permanentguide

The vehicle might be equipped withguides in front of the mountingbrackets to support the installation ofthe child restraint system.


The covers of the guides will swivelbackwards automatically whenattaching the child restraint system.

Top-tether fastening eyesDepending on country specificequipment, the vehicle might havetwo or three fastening eyes.Top-Tether fastening eyes aremarked with the symbol : for a childrestraint.

For non-ISOFIX child restraints,fasten the Top-Tether strap to theTop-Tether fastening eyes. The strapmust run between the two guide rodsof the head restraint.For ISOFIX child restraints, fasten theTop-Tether strap to the Top-Tetherfastening eyes in addition to theISOFIX mounting. The strap must runbetween the two guide rods of thehead restraint.ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF.

58 Storage

Storage

Storage compartments ................ 58Glovebox ................................... 58Cupholders ................................ 58Front storage ............................. 59Sunglasses storage ................... 59Underseat storage ..................... 60Centre console storage ............. 60Rear carrier system ................... 60

Load compartment ....................... 70Load compartment cover ........... 72Rear floor storage cover ............ 72Lashing eyes ............................. 72Warning triangle ........................ 72First aid kit ................................. 73

Roof rack system ......................... 73Roof rack ................................... 73

Loading information ..................... 73

Storage compartments

9 Warning

Do not store heavy or sharpobjects in the storagecompartments. Otherwise, thestorage compartment lid couldopen and vehicle occupants couldbe injured by objects being thrownaround in the event of hardbraking, a sudden change indirection or an accident.

Glovebox

To open, pull the handle.The glovebox should be closed whiledriving.

Cupholders

The cupholders are located in thecentre console and rear part of thecentre console.

Storage 59

To use the rear seat cupholder, pullthe strap in the rear seat armrest.

Front storage

A storage compartment is locatednext to the steering wheel. Pull thehandle to open.

A further storage compartment islocated in the centre console.To open, press the button.The covers of the storagecompartments should be closed whiledriving.

Sunglasses storage

Fold down and open.Do not use for storing heavy objects.

60 Storage

Underseat storage

Lift drawer at the front and pull out. Toclose, push the drawer in andengage.

Centre console storage

Push down the button and slide coverbackwards.

Rear carrier systemRear carrier system for threebicycles

The rear carrier system (Flex-Fixsystem) allows one bicycle to beattached to an extendable carrierintegrated into the vehicle floor. It ispossible to attach two further bicycleson an adapter. The transportation ofother objects is not permitted.The maximum load of the rear carriersystem is 60 kg with attached adapterand 30 kg without attached adapter.This allows the attachment of anelectrically-powered bicycle to the

Storage 61

rear carrier system. The maximumload per bicycle on the adapter is20 kg.The wheelbase of a bicycle must notexceed 1.15 metres. Otherwise thesecure fastening of a bicycle is notpossible.If not in use, the rear carrier systemmust be slid back into the vehiclefloor.There must not be any objects on thebicycles that could become looseduring transportation.

Caution

If the rear carrier system isextended and the vehicle is fullyloaded, the ground clearance willbe reduced.Drive carefully whenever the roadhas a steep inclination or whendriving over a ramp, bump, etc.

Caution

Consult your bicycle dealer beforeattaching bicycles with carbonframes. The bicycles may getdamaged.

NoticeThe tail lights of the vehicle will bedeactivated if the tail lights of therear carrier system are installed.

ExtendingOpen the tailgate.

9 Warning

No-one should be in the extensionzone of the rear carrier system,risk of injury.

Pull release lever up. The rear carriersystem disengages and travelsquickly out of the rear bumper.

62 Storage

Completely pull out the rear carriersystem until you hear it engage.Ensure that it is not possible to pushin the rear carrier system withoutpulling the release lever again.

9 Warning

It is only permissible to fit objectsto the rear carrier system if thesystem has been correctlyengaged. If the rear carrier systemwill not engage correctly, do not fitobjects to the system and slide thesystem back. Seek the assistanceof a workshop.

Unfold number plate holder

Lift the number plate holder and foldit backwards.Affix the number plate before first useof the rear carrier system.

Fold out tail lights

To install the tail lights, remove bothpins (1). Pull tail lights out of theretainer towards the front (2) anddownwards and swivel them to theside.

Storage 63

Push the tail lights into the retainer(1) and reinstall pins (2) all the way toattach the lights.

Fold out wheel recess

Remove strap and fold out the wheelrecess.

Lock the rear carrier system

Remove strap and swivel bothclamping levers sideways as far asthey will go.Otherwise safe functionality is notguaranteed.

Assembling the bicycle rack

Lift the rack at the rear (1) and pull itbackwards.Fold up the rack (2).

64 Storage

Push down the rack (1) and swivelhandle (2) backwards to engage.

Press button (1) and remove left partof rack (2).Press button (1) and insert left part ofrack into the right part (2).

Attaching a bicycle

1. Rotate the pedals into position, asshown in the illustration, and putthe bicycle on the wheel recess.

Make sure that the bicycle standscentrally on the wheel recesses.

2. Attach the short mounting bracketto the bicycle frame. Turn theknob clockwise to fasten.

Storage 65

3. Secure both bicycle wheels to thewheel recesses using the strapretainers.

4. Check the bicycle to make sure itis secure.

Caution

Ensure gap between bicycle andvehicle is at least 5 cm. Ifnecessary, loosen handlebar andswivel sideways.

Attaching the adapterWhen carrying more than one bicycle,the adapter must be fixed.

1. Apply the adapter to the rearcarrier system, as shown in theillustration.

2. Turn the lever (1) forwards andhold it, then lower the adapter (2)at the rear.

3. Release lever and check if theadapter is engaged securely.

4. Guide the strap attached to theadapter underneath the leverwhen folding back the rear carriersystem. Fasten the strap.

Attaching further bicyclesThe attachment of further bicycles issimilar to the attachment of the firstbicycle. Additionally, some stepsmust be considered:1. Before putting on the bicycle,

always unfold the wheel recessesfor the next bicycle if necessary.

2. Always rotate the pedals into anappropriate position beforeputting on the bicycle.

66 Storage

3. Position the bicycles on the rearcarrier system alternately alignedto the left and to the right.

4. Align the bicycles with the oneattached previously. The wheelhubs of the bicycles must nottouch each other.

5. Attach the bicycles with mountingbrackets and strap retainers asdescribed for the first bicycle. Themounting brackets should befixed in parallel.Use the long mounting bracket toattach the second bicycle to therack.

Use the short accessory mountingbracket to attach the third bicycle.The bracket must be fixedbetween the frames of the secondand third bicycle.

6. Additionally, secure both bicyclewheels of the third bicycle to thewheel recesses using thetensioning straps.

It is recommended to attach awarning sign to the rearmost bicycle,to increase visibility.

Fold the rear carrier systembackwardsThe rear carrier system can be foldedbackwards to gain access to the loadcompartment.● Without attached adapter:

Push the lever (1) to disengageand hold it.

Storage 67

Pull the rack (2) backwards tofold the rear carrier system.

● With attached adapter:

9 Warning

Take care when disengaging therear carrier system as it will tiltbackwards. Risk of injury.

Hold frame (1) of rearmostbicycle with one hand and pull theloop (2) to disengage.Hold rearmost bicycle with bothhands and fold the rear carriersystem backwards.

To increase visibility, the tail lights ofthe vehicle are activated when therear carrier system is folded back.

9 Warning

When folding the rear carriersystem forwards again, ensurethat the system is engagedsecurely.

Removing bicyclesUndo strap retainers on both bicycletyres.Turn knob anticlockwise and removemounting brackets.

Detaching adapterDetach the adapter before removingthe bicycle on the rear carrier system.1. Fold in wheel recesses.

2. Unbutton the strap.

3. Turn the lever (1) forwards andhold it.

4. Lift the adapter (2) at the rear andremove.

68 Storage

Disassembling the bicycle rack

Press button (1) and remove upperpart of rack (2).

Press button (1) and reinstall rack (2).

Arrange mounting brackets as shownin the illustration.Swivel handle (1) sideways todisengage and lift the rack (2).

Fold the rack backwards, then pushforwards until it stops (1).Press the rack down at the rear (2).

Fold in wheel recessFold in wheel recess. Fasten strap.

Stow the strap retainers accurately.

Storage 69

Unlock the rear carrier system

Swivel both clamping levers inwardsas far as they will go. Fasten strap.

Fold in tail lightsRemove both pins. Pull tail lights outof the retainer and put them in theposition to be stored in.

Push the tail lights into the retainer(1). Insert pins into the designatedholes of the retainer and the tail lights(2).NoticeCheck that the tail lights of thevehicle are working properly.

Fold in number plate holderLift the number plate holder and foldit forwards.

Retracting the rear carrier system

Caution

Ensure that all foldable parts, e.g.wheel recesses and mountingbrackets, are stowed correctly.Otherwise the rear carrier systemmay get damaged when trying toretract it.

Push the release lever up and hold it.Lift the system slightly and push it intothe bumper until it engages.Release lever must return to originalposition.

70 Storage

9 Warning

If the system cannot be correctlyengaged, seek the assistance of aworkshop.

Load compartment

Load compartment extension

Caution

First fold down the rear seatcushion before folding the rearseat backrest.Disregard may lead to damage tothe rear seat.

1. Push head restraints down bypressing the catch.

NoticeTo ensure sufficient room for rearseat cushion operation, slide thefront seat forward and move the frontseat backrest upright.

2. Pull the loop under the seatcushion and fold down the seatcushion.

3. Pull the release lever on top of therear backrest.

Storage 71

4. Fold the backrest forward anddown.

5. Put the seat belts for the outboardseats into the belt guides.

To return the backrest to the originalposition, pull out the seat belt from thebelt guides and lift backrest up.Push backrest firmly into place.

9 Warning

When folding up, ensure thatbackrests are securely engaged inposition before driving. Failure todo so may result in personal injuryor damage to the load or vehicle inthe event of hard braking or acollision.

Ensure the seat belts are not pinchedby the latch.The centre rear seat belt may lockwhen you raise the backrest. If thishappens, allow the belt go back all theway and repeat operation.If the seat belt is still locked, fold downthe seat cushion and try again.To return the rear seat cushion, putthe rear part of the seat cushion in itsoriginal position ensuring that theseat belt buckle straps are not twisted

or caught under the seat cushion,then push the front part of the seatcushion firmly down until it latches.

Caution

When returning rear seat backrestto the upright position, place therear seat belt and bucklesbetween the rear seat backrestand one cushion. Make sure therear seat belt and buckles do notget pinched under the rear seatcushion.Ensure the seat belts are nottwisted or caught in the seatbackrest and are arranged in theirproper position.

72 Storage

Load compartment cover

Do not place any objects on the cover.

RemovingUnhook retaining straps from tailgate.Lift cover at the rear and push itupwards at the front.Remove the cover.

FittingEngage cover in side guides and folddownwards.Attach retaining straps to tailgate.

Rear floor storage coverRear floor cover

Grasp the handle and lift the cover.

Mount the cover to the hook at thesidewall.

Lashing eyesThe lashing eyes are designed tosecure items against slippage, e.g.using lashing straps or luggage net.

Warning triangle

Stow the warning triangle below thefloor cover in the load compartment.Secure it with the strap.

Storage 73

First aid kit

Stow the first aid kit in the storagecompartment at the left sidewall of theload compartment.

Roof rack systemRoof rack

The roof rack has side rails attachedto the roof.For safety reasons and to avoiddamage to the roof, the vehicleapproved roof rack system isrecommended. For furtherinformation contact your workshop.

Loading information● Heavy objects in the load

compartment should be placedagainst the seat backrests.Ensure the backrests aresecurely engaged. If objects canbe stacked, the heavier objectsshould be placed at the bottom.

● Secure objects with lashingstraps attached to the lashingeyes 3 72.

● Secure loose objects in loadcompartment to prevent sliding.

● When transporting objects in theload compartment, the backrestsof the rear seats must not beangled forward.

● Do not allow the load to protrudeabove the upper edge of thebackrests.

● Do not place any objects on theload compartment cover or theinstrument panel, and do notcover the sensor on top of theinstrument panel.

74 Storage

● The load must not obstruct theoperation of the pedals, parkingbrake and gear selector, orhinder the freedom of movementof the driver. Do not place anyunsecured objects in the interior.

● Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrownaround inside the vehicle andcause personal injury or damageto the load or vehicle.

● The payload is the differencebetween the permitted grossvehicle weight (see identificationplate 3 219) and the EC kerbweight.To calculate the payload, enterthe data for your vehicle in theweights table at the front of thismanual.The EC kerb weight includesweights for the driver (68 kg),

luggage (7 kg) and all fluids (fueltank 90% full).Optional equipment andaccessories increase the kerbweight.

● Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has adetrimental effect on vehiclehandling due to the vehicle’shigher centre of gravity.Distribute the load evenly andsecure it properly with retainingstraps. Adjust the tyre pressureand vehicle speed according tothe load conditions. Check andretighten the straps frequently.Do not drive faster than 75 mph.

● The permissible roof load is75 kg. The roof load is thecombined weight of the roof rackand the load.

Instruments and controls 75

Instruments andcontrols

Controls ....................................... 76Steering wheel adjustment ........ 76Steering wheel controls ............. 76Heated steering wheel ............... 76Horn ........................................... 77Windscreen wiper/washer ......... 77Rear window wiper/washer ....... 79Outside temperature .................. 79Clock ......................................... 80Power outlets ............................. 82

Warning lights, gauges and indi‐cators ........................................... 83

Speedometer ............................. 83Odometer .................................. 83Trip odometer ............................ 83Tachometer ............................... 84Fuel gauge ................................ 84Fuel selector .............................. 85Engine coolant temperaturegauge ....................................... 85

Service display .......................... 86Control indicators ...................... 86Turn signal ................................. 90Seat belt reminder ..................... 91

Airbag and belt tensioners ......... 91Airbag deactivation .................... 92Charging system ....................... 92Malfunction indicator light .......... 92Brake and clutch system ........... 92Antilock brake system (ABS) ..... 92Gear shifting .............................. 93Descent control system ............. 93Lane departure warning ............ 93Electronic Stability Control off . . . 93Electronic Stability Control andTraction Control system ........... 93

Traction Control system off ....... 93Preheating ................................. 93Tyre pressure monitoringsystem ...................................... 94

Engine oil pressure .................... 94Low fuel ..................................... 94Immobiliser ................................ 94Exterior light .............................. 95High beam ................................. 95High beam assist ....................... 95Adaptive forward lighting ........... 95Fog light ..................................... 95Rear fog light ............................. 95Cruise control ............................ 95Vehicle detected ahead ............. 95Speed limiter ............................. 95Traffic sign assistant .................. 96Door open .................................. 96

Information displays ..................... 96Driver Information Centre .......... 96Info display .............................. 100

Vehicle messages ...................... 102Warning chimes ....................... 103Battery voltage ........................ 103

Vehicle personalisation .............. 104Telematics service ..................... 108

OnStar ..................................... 108ERA GLONASS ....................... 112

76 Instruments and controls

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controls

The Infotainment system and thecruise control can be operated via thecontrols on the steering wheel.Further information is available in theInfotainment manual.Cruise control 3 151

Heated steering wheel

Activate heating by pressing *.Activation is indicated by the LED inthe button.Heating is operational when theengine is running.


Horn

Press j.

Windscreen wiper/washerWindscreen wiper

HI : fastLO : slowINT : interval wiping or automatic

wiping with rain sensorOFF : off

For a single wipe when thewindscreen wiper is off, press thelever down to position 1x.Do not use if the windscreen is frozen.Switch off in car washes.

Adjustable wiper interval

Wiper lever in position INT.Turn the adjuster wheel to adjust thedesired wipe interval:short interval : turn adjuster

wheel upwardslong interval : turn adjuster

wheel downwards


Automatic wiping with rain sensor

INT : automatic wiping with rainsensor

The rain sensor detects the amount ofwater on the windscreen andautomatically regulates the frequencyof the windscreen wiper.

Adjustable sensitivity of the rainsensor

Turn the adjuster wheel to adjust thesensitivity:low sensitivity : turn adjuster

wheel downwardshigh sensitivity : turn adjuster

wheel upwards

Keep the sensor free from dust, dirtand ice.

Windscreen washer

Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.Washer fluid 3 181


Rear window wiper/washer

Press the rocker switch to activate therear window wiper:upper switch : continuous

operationlower switch : intermittent

operationmiddle position : off

Push lever. Washer fluid is sprayedonto the rear window and the wiperwipes a few times.Do not use if the rear window isfrozen.Switch off in car washes.The rear window wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display.Washer fluid 3 181Vehicle personalisation 3 104.

Outside temperature

A drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay.


If outside temperature drops to0.5 °C, a warning message isdisplayed in the Driver InformationCentre.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above 0°C.

ClockDate and time are shown in theInfo-Display.Info-Display 3 100.

Graphic-Info-DisplayPress MENU to open the respectiveaudio menu.

Select Time and Date.

Set TimeSelect Set Time to enter therespective submenu.Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff (Manual).If Off (Manual) is selected, adjusthours and minutes.Repeatedly select 12-24 HR at thebottom of the screen to choose a timemode.If the 12-hour mode is selected, athird column for AM and PM selectionis displayed. Select the desiredoption.

Set DateSelect Set Date to enter therespective submenu.Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff (Manual).If Off (Manual) is selected, adjust thedate settings.

7'' Colour-Info-DisplayPress ; and then select Settings.

Select Time and Date to display therespective submenu.

Set Time FormatTo select the desired time format,touch the screen buttons 12 h or 24 h.

Set Date FormatTo select the desired date format,select Set Date Format and choosebetween the available options in thesubmenu.

Auto SetTo choose whether time and date areto be set automatically or manually,select Auto Set.


For time and date to be setautomatically, select On - RDS.For time and date to be set manually,select Off - Manual. If Auto Set is setto Off - Manual, the submenu itemsSet Time and Set Date becomeavailable.

Set time and dateTo adjust the time and date settings,select Set Time or Set Date.Touch + and - to adjust the settings.

8'' Colour-Info-DisplayPress ; and then select theSettings icon.Select Time and Date.

Set timeSelect Set Time to enter therespective submenu.

Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff - Manual.If Off - Manual is selected, adjusthours and minutes by touching n oro.Touch 12-24 Hr on the right side of thescreen to select a time mode.If 12-hour mode is selected, a thirdcolumn for AM and PM setting isdisplayed. Select the desired option.

Set dateSelect Set Date to enter therespective submenu.

NoticeIf date information is automaticallyprovided, this menu item is notavailable.

Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff - Manual.If Off - Manual is selected, adjust thedate by touching n or o.

Clock displaySelect Clock Display to enter therespective submenu.To turn off the digital clock display inthe menus, select Off.


Power outlets

A 12 Volt power outlet is located in thefront console behind the cover. Toopen, push the button.A further 12 Volt power outlet may belocated in the rear centre console.Do not exceed the maximum powerconsumption of 120 watts.Depending on equipment, a 230 Voltpower outlet is located in the rearcentre console.

Do not exceed the maximum powerconsumption of 150 watts.With ignition off the power outlet isdeactivated.Additionally the power outlet isdeactivated in the event of low batteryvoltage.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.

Caution

Do not connect any currentdelivering accessories, e.g.electrical charging devices orbatteries.Do not damage the outlets byusing unsuitable plugs.


Warning lights, gaugesand indicatorsSpeedometer

Indicates vehicle speed.

Odometer

The total recorded distance isdisplayed in miles.

Trip odometerThe recorded distance since the lastreset is displayed on the trip computerpage.Trip odometer counts up to9,999 miles and then restarts at 0.Two trip odometer pages areselectable for different trips.

Midlevel instrument cluster

Select ; by pressing Menu on theturn signal lever. Turn adjuster wheeland select ;1 or ;2. Each tripodometer page can be resetseparately by pressing SET/CLR onthe turn signal lever for a few secondson the respective menu.


Uplevel instrument cluster

Select Info page Q by pressing Menu.Choose page Trip A or Trip B byturning adjuster wheel on the turnsignal lever.Each trip odometer page can be resetseparately by pressing SET/CLR onthe turn signal lever for a few secondson the respective menu.Driver Information Centre 3 96.

Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.

Fuel gauge

Displays the level in the fuel or gastank depending on the operationmode.The arrow indicates the vehicle sidewhere the fuel filler flap is located.Control indicator Y illuminates if thelevel in the tank is low. Refuelimmediately if it flashes.During liquid gas operation, thesystem automatically switches over topetrol operation when gas tanks areempty 3 85.Never run fuel tank dry.


Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified tank capacity.

Fuel selector

Press LPG to switch between petroland liquid gas operation. The LED inthe button shows the currentoperating mode.LED off : petrol operationLEDflashes

: checking conditions forfuel transition to liquidgas operation.Illuminates if conditionsare fulfilled.

LED illu‐minates

: liquid gas operation

LEDflashesfivetimesandextin‐guishes

: liquid gas tank is emptyor failure in liquid gassystem. A message isdisplayed in the DriverInformation Centre.

As soon as the liquid gas tank isempty, petrol operation isautomatically engaged until theignition is switched off.Fuel for liquid gas operation 3 166.

Engine coolant temperaturegauge

Displays the coolant temperature.50 : engine operating

temperature not yetreached

centralarea

: normal operatingtemperature

130 : temperature too high


Caution

If engine coolant temperature istoo high, stop vehicle, switch offengine. Danger to engine. Checkcoolant level.

Service displayThe engine oil life system informswhen to change the engine oil andfilter. Based on driving conditions, theinterval at which an engine oil andfilter change will be indicated can varyconsiderably.

The remaining oil life duration menuis displayed in the Driver InformationCentre 3 96.

On Midlevel display select theOption ? Menu by pressingMENU on the turn signal lever. Turnthe adjuster wheel to select theRemaining Oil Life page.On Uplevel display select the Info QMenu by pressing MENU on the turnsignal lever. Turn the adjuster wheelto select Oil Life page.Remaining oil life duration is indicatedin percentage.

ResetPress SET/CLR on turn signal leverfor several seconds to reset. Theengine oil life page must be active.The ignition must be switched on butengine not running.The system must be reset every timethe engine oil is changed to allowproper functionality. Seek theassistance of a workshop.

Next serviceWhen the system has calculated thatengine oil life has diminished, awarning message appears in theDriver Information Centre. Haveengine oil and filter changed by aworkshop within one week or300 miles (whichever occurs first).Driver Information Centre 3 96.Service information 3 216.

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrumentversions. Depending on the


equipment, the position of the controlindicators may vary. When theignition is switched on, most controlindicators will illuminate briefly as afunctionality test.The control indicator colours mean:red : danger, important reminderyellow : warning, information, faultgreen : confirmation of activationblue : confirmation of activationwhite : confirmation of activation

Control indicators in theinstrument clusterDepending on the version, twoinstrument clusters are available:


Midlevel instrument cluster


Uplevel instrument cluster


Control indicators in the centreconsole

Overview

O Turn signal 3 90

X Seat belt reminder, driver3 91

k Seat belt reminder, frontpassenger 3 91

v Airbag and belt tensioners3 91

V /*

Airbag deactivation 3 92

p Charging system 3 92

Z Malfunction indicator light3 92

R Brake and clutch system3 92

u Antilock brake system (ABS)3 92

R Gear shifting 3 93

u Descent control system3 93

) Lane departure warning3 93

n Electronic Stability Control off3 93

b Electronic Stability Controland Traction Control system3 93

k Traction Control system off3 93

! Preheating 3 93

w Tyre pressure monitoringsystem 3 94

I Engine oil pressure 3 94

Y Low fuel 3 94

d Immobiliser 3 94

8 Exterior light 3 95

C High beam 3 95

f High beam assist 3 95

f Adaptive forward lighting3 95

> Fog light 3 95

r Rear fog light 3 95

m Cruise control 3 95

A Vehicle detected ahead3 95

L Speed limiter 3 95

L Traffic sign assistant 3 96

h Door open 3 96

Turn signalO illuminates or flashes green.


Illuminates brieflyThe parking lights are switched on.

FlashesA turn signal or the hazard warningflashers are activated.Rapid flashing: failure of a turn signallight or associated fuse, failure of turnsignal light on trailer.Bulb replacement 3 185, Fuses3 189.Turn signals 3 121.

Seat belt reminderSeat belt reminder on front seatsX for driver's seat illuminates orflashes red in the instrument cluster.k for front passenger seat illuminatesor flashes red in the centre consolewhen seat is occupied.

IlluminatesAfter the ignition has been switchedon until the seat belt has beenfastened.

FlashesAfter having started the engine untilthe seat belt has been fastened.

Seat belt status on rear seats(vehicles with Midlevel display)X illuminates or flashes white or greyin the Driver Information Centre, afterhaving started the engine.

Illuminates whiteSeat belt is unfastened.

Illuminates greySeat belt has been fastened.

Flashes white or greyFastened seat belt has beenunfastened.Fastening the seat belt 3 44.

Seat belt status on rear seats(vehicles with Uplevel display)X illuminates green or grey or flashesyellow in the Driver InformationCentre, after having started theengine.

Illuminates greySeat belt is unfastened.

Illuminates greenSeat belt has been fastened.

Flashes yellowFastened seat belt has beenunfastened.Fastening the seat belt 3 44.

Airbag and belt tensionersv illuminates red.When the ignition is switched on, thecontrol indicator illuminates for a fewseconds. If it does not illuminate,does not go out after a few secondsor illuminates whilst driving, there is afault in the airbag system. Seek theassistance of a workshop. Theairbags and belt pretensioners mayfail to trigger in the event of anaccident.Deployment of the belt pretensionersor airbags is indicated by continuousillumination of v.


9 Warning

Have the cause of the faultremedied immediately by aworkshop.

Belt pretensioners, airbag system3 43, 3 46.

Airbag deactivationV illuminates yellow.The front passenger airbag isactivated.* illuminates yellow.The front passenger airbag isdeactivated 3 51.

9 Danger

Risk of fatal injury for a child usinga child restraint system togetherwith activated front passengerairbag.Risk of fatal injury for an adultperson with deactivated frontpassenger airbag.

Charging systemp illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningStop, switch off engine. Battery is notcharging. Engine cooling may beinterrupted. The brake servo unit maycease to be effective. Seek theassistance of a workshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded. Seek the assistance of aworkshop immediately.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Brake and clutch systemR illuminates red.The brake and clutch fluid level is toolow, when manual parking brake isnot applied 3 181.

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Illuminates when the manual parkingbrake is applied and ignition isswitched on 3 147.

Antilock brake system(ABS)u illuminates yellow.


Illuminates for a few seconds after theignition is switched on. The system isready for operation when the controlindicator extinguishes.If the control indicator does notextinguish after a few seconds, or if itilluminates while driving, there is afault in the ABS. The brake systemremains operational but without ABSregulation.Antilock brake system 3 147.

Gear shiftingR or S with the number of a higher orlower gear is indicated, when up- ordownshifting is recommended for fuelsaving reasons.

Descent control systemu illuminates or flashes green.

Illuminates greenThe system is ready for operation.

Flashes greenThe system is in operation.

Lane departure warning) illuminates green or flashes yellow.

Illuminates greenSystem is switched on and ready tooperate.

Flashes yellowSystem recognises an unintendedlane change.Lane departure warning 3 164.

Electronic Stability Controloffn illuminates yellow.The system is deactivated.

Electronic Stability Controland Traction Control systemb illuminates or flashes yellow.

IlluminatesA fault in the system is present.Continued driving is possible. Drivingstability, however, may deterioratedepending on road surfaceconditions.Have the cause of the fault remediedby a workshop.

FlashesThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree.Electronic Stability Control 3 149,Traction Control system 3 148.

Traction Control system offk illuminates yellow.The system is deactivated.

Preheating! illuminates yellow.Preheating of diesel engine isactivated. Only activates whenoutside temperature is low.


Tyre pressure monitoringsystemw illuminates or flashes yellow.

IlluminatesTyre pressure loss. Stop immediatelyand check tyre pressure.

FlashesFault in system or tyre withoutpressure sensor mounted (e.g. sparewheel). After 60-90 seconds thecontrol indicator illuminatescontinuously. Consult a workshop.Tyre pressure monitor system3 196.

Engine oil pressureI illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress clutch.2. Select neutral gear, set selector

lever to N.3. Move out of the flow of traffic as

quickly as possible withoutimpeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off,considerably more force is neededto brake and steer. During anAutostop the brake servo unit willstill be operational.

Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seeking theassistance of a workshop 3 179.

Low fuelY illuminates or flashes yellow.

IlluminatesLevel in fuel tank is too low.

FlashesFuel used up. Refuel immediately.Never run the tank dry.Refuelling 3 168.Catalytic converter 3 141.Bleeding the diesel fuel system3 183.

Immobiliserd flashes yellow.Fault in the immobiliser system. Theengine cannot be started.


Have the cause of the fault remediedby a repairer.

Exterior light8 illuminates green.The exterior lights are on 3 114.

High beamC illuminates blue.Illuminates when high beam is on orduring headlight flash 3 115, or whenhigh beam is on with high beamassist, adaptive forward lighting3 118.

High beam assistf illuminates green.The high beam assist is activated3 118.

Adaptive forward lightingf illuminates or flashes yellow.

IlluminatesThe adaptive forward lighting systemneeds a service.Seek the assistance of a workshop.Adaptive forward lighting 3 118.

FlashesSystem switched to symmetrical lowbeam.Control indicator f flashes for approx.4 seconds after the ignition isswitched on as a reminder that thesystem has been activated 3 117.Automatic light control 3 115.

Fog light> illuminates green.The front fog lights are on 3 121.

Rear fog lightr illuminates yellow.The rear fog light is on 3 121.

Cruise controlm illuminates white or green.

Illuminates whiteThe system is on.

Illuminates greenCruise control is active.Cruise control 3 151.

Vehicle detected aheadA illuminates green or yellow.

Illuminates greenA vehicle ahead is detected in thesame lane.

Illuminates yellowThe distance to a preceding movingvehicle gets too small or whenapproaching another vehicle toorapidly.Forward collision alert 3 154.

Speed limiterL illuminates white or green.

Illuminates whiteThe system is on.


Illuminates greenSpeed limiter is active. Set speed isindicated near L symbol.Speed limiter 3 153.

Traffic sign assistantL displays detected traffic signs as acontrol indicator.Traffic sign assistant 3 160.

Door openh illuminates red.A door or the tailgate is open.

Information displaysDriver Information CentreThe Driver Information Centre islocated in the instrument cluster.Depending on the version and theinstrument cluster, the DriverInformation Centre is available asMidlevel display or Uplevel display.Driver Information Centre indicatesdepending on the equipment:● overall and trip odometer● vehicle information● trip/fuel information● driving economy information● vehicle and warning messages● vehicle settings

Midlevel display

Main menus are:● Trip/fuel information, displayed

by ;, see description below.● Vehicle information, displayed

by ?, see description below.● Eco information, displayed by

@, see description below.Some of the displayed functions differwhen the vehicle is being driven or ata standstill and some functions areonly active when the vehicle is beingdriven.


Uplevel display

Main menus are:● Trip/fuel information, displayed

by Info Q, see description below.● Vehicle information, displayed by

Options L, see descriptionbelow.

Some of the displayed functions differwhen the vehicle is being driven or ata standstill and some functions areonly active when the vehicle is beingdriven.

Selecting menus and functionsThe menus and functions can beselected via the buttons on the turnsignal lever.

Press MENU to switch between themain menus or to return from asubmenu to the next higher menulevel.Turn the adjuster wheel to select asubmenu of the main menu or to seta numeric value.Press SET/CLR to select and confirma function.

Vehicle and service messages arepopped up in the Driver InformationCentre if required. Confirm messagesby pressing SET/CLR. Vehiclemessages 3 102.

Trip/fuel information menu, ;or Info QThe following list contains all possibleInfo Menu pages. Some may not beavailable for your particular vehicle.Depending on the display, somefunctions are symbolised.Turn the adjuster wheel to select apage:● Trip odometer 1/2 or A/B● Average fuel consumption● Average speed● Digital speed● Fuel range● Instantaneous fuel consumption● Remaining oil life● Tyre pressure● Traffic sign assistant● Following distance● Timer


On Midlevel display the pagesRemaining Oil Life, Tyre Pressure,Traffic Sign Assistant and FollowingDistance are displayed in the Vehicleinformation menu, select ?.

Trip odometer 1/2 or A/BTrip odometer displays the currentdistance since a certain reset.Trip odometer counts up to a distanceof 9,999 miles then restarts at 0.To reset press SET/CLR for a fewseconds.The information of trip odometer page1/A and 2/B can be reset separatelywhile the respective display is active.

Average Fuel ConsumptionDisplay of average consumption. Themeasurement can be reset at anytime and starts with a default value.To reset press SET/CLR for a fewseconds.

Average speedDisplay of average speed. Themeasurement can be reset at anytime.

To reset press SET/CLR for a fewseconds.

Digital speedDigital display of the instantaneousspeed.

Fuel rangeRange is calculated from current fuellevel and current consumption. Thedisplay shows average values.After refuelling, the range is updatedautomatically after a brief delay.When the level in the fuel tank is low,a message appears on the displayand the control indicator Y in the fuelgauge illuminates.When the fuel tank must be refuelledimmediately, a warning messageappears and remains on the display.Additionally, the control indicator Y inthe fuel gauge flashes 3 94.

Instantaneous Fuel ConsumptionDisplay of the instantaneousconsumption.

Remaining Oil LifeIndicates an estimate of the oil'suseful life. The number in percentagemeans the remainder of current oil life3 86.

Tyre PressureChecks tyre pressure of all wheelsduring driving 3 196.

Traffic sign assistantDisplays the detected traffic signs forthe current route section 3 160.

Following DistanceDisplays the distance in seconds to apreceding moving vehicle 3 156.

TimerTo start and stop follow theinstructions on the display. To reset,press SET/CLR.

Eco information menu, @● Top consumers● Economy trend● Eco index


On Uplevel display the pages TopConsumers, Economy Trend and Ecoindex, are displayed in the Trip/fuelinformation menu, select Info.

Top ConsumersList of top comfort consumerscurrently switched on is displayed indescending order. Fuel savingpotential is indicated.During sporadic driving conditions,the engine will activate the heatedrear window automatically to increasethe engine load. In this event, theheated rear window is indicated asone of the top consumers, withoutactivation by the driver.

Economy Trend

Displays the average consumptiondevelopment over a distance of31 miles. Filled segments display theconsumption in 3.1 mile steps andshows the effect of topography ordriving behaviour on fuelconsumption.

Economy indexThe current fuel consumption isindicated on an economic scale. Foreconomical driving, adapt drivingstyle to keep the filled segmentswithin the Eco area. The moresegments are filled, the higher thefuel consumption.

Simultaneously the averageconsumption value is indicated.

Vehicle information menu, ? orOptions LThe following list contains all possibleOptions Menu pages. Some may notbe available for your particularvehicle. Depending on the displaysome functions are symbolised.Turn the adjuster wheel to select apage and follow the instructions givenin the submenus:● Units● Info pages● Speed warning● Tyre loading

UnitsPress SET/CLR while units isdisplayed. Select imperial or metricunits by turning adjuster wheel.Confirm by pressing SET/CLR.

Info pagesPress SET/CLR while Info pages isdisplayed. A list of all items in the InfoMenu is displayed. Select the


functions to be displayed in the Infopage by turning the adjuster wheeland confirm by pressing SET/CLR.Selected pages have a 9 in acheckbox. Non-viewable functionshave a blank checkbox. See InfoMenu above.

Speed warning

The speed warning function alerts thedriver when a set speed is exceeded.To set the speed warning, pressSET/CLR while the page is displayed.Turn the adjuster wheel to select andadjust the value. Press SET/CLR toset the speed. Once the speed is set,this feature can be turned off by

pressing SET/CLR while viewing thispage. If the selected speed limit isexceeded, a pop-up warning isdisplayed with a chime.

Tyre LoadThe tyre pressure category accordingto the actual tyre inflation pressurecan be selected 3 196. Turn theadjuster wheel to select a categoryLight ,Eco or Max.Press SET/CLR to confirm category.

Info displayThe Info-Display is located in theinstrument panel near the instrumentcluster.Depending on the vehicleconfiguration the vehicle has a● Graphic-Info-Display

or● 7'' Colour-Info-Display with

touchscreen functionalityor

● 8'' Colour-Info-Display withtouchscreen functionality

The Info displays can indicate:● time 3 80● outside temperature 3 79● date 3 80● Infotainment system, see

description in the Infotainmentmanual

● indication of rear view camera3 159

● indication of parking assistinstructions 3 157

● navigation, see description in theInfotainment manual

● system messages● settings for vehicle

personalisation 3 104


Graphic-Info-Display

Press X to switch on the display.Press MENU to select main menupage.Turn MENU to select a menu page.Press MENU to confirm a selection.Press BACK to exit a menu withoutchanging a setting.

7'' Colour-Info-Display

Selecting menus and settingsMenus and settings are accessed viathe display.

Press X to switch on the display.Press ; to display the homepage.Touch required menu display iconwith the finger.Touch a respective icon to confirm aselection.Touch 9 to return to the next highermenu level.Press ; to return to the homepage.For further information, seeInfotainment manual.Vehicle personalisation 3 104.

8'' Colour-Info-Display

Selecting menus and settingsThere are three options to operate thedisplay:● via buttons below the display● by touching the touchscreen with

the finger● via speech recognition

Button operation

Press X to switch on the display.Press ; to display the homepage.Turn MENU to select a menu displayicon or a function or to scroll asubmenu list.


Press MENU to confirm a selection.Press BACK to exit a menu withoutchanging a setting.Press ; to return to the homepage.For further information, seeInfotainment manual.Touchscreen operationDisplay must be switched on bypressing X. Press ; to selecthomepage.Touch required menu display icon ora function with the finger.Scroll a longer submenu list with thefinger up or down.Confirm a required function orselection by touching.Touch q on the display to exit amenu without changing a setting.Press ; to return to the homepage.For further information, seeInfotainment manual.Speech recognitionDescription see Infotainment manual.Vehicle personalisation 3 104.

Valet modeSome functions of the DriverInformation Centre and the Info-Display can be limited for somedrivers.Activation or deactivation of valetmode can be set in the menuSettings in the vehicle personalisationmenu.Vehicle personalisation 3 104.For more information seeInfotainment manual.

Vehicle messagesMessages are indicated mainly in theDriver Information Centre, in somecases together with a warning chime.

Press SET/CLR on the turn signallever to confirm a message.

Vehicle and service messagesThe vehicle messages are displayedas text. Follow the instructions givenin the messages.


Warning chimesWhen starting the engine or whilstdrivingOnly one warning chime will sound ata time.The warning chime regardingunfastened seat belts has priorityover any other warning chime.● If a door, the tailgate or bonnet is

open.● If seat belt is not fastened.● If a certain speed is exceeded

with parking brake applied.● If a programmed speed or speed

limit is exceeded.● If a warning message appears in

the Driver Information Centre.● If approaching a vehicle ahead

too closely.● If the electronic key is not in the

passenger compartment.● If an unintended lane change

occurs.

● If the parking assist detects anobject.

● If the fuel level is low.

When the vehicle is parked and/orthe driver's door is opened● With exterior lights on.

During an Autostop● If the driver's door is opened.● If any condition for an autostart is

not fulfilled.

Battery voltageWhen the battery voltage is runninglow, a warning message or warningcode 174 will appear in the DriverInformation Centre.1. Switch off immediately any

electrical consumers which arenot required for a safe ride, e.g.seat heating, heated rear windowor other main consumers.

2. Charge the battery by drivingcontinuously for a while or byusing a charging device.

The warning message or warningcode will disappear after the enginehas been started twice consecutivelywithout a voltage drop.If the battery cannot be recharged,have the cause of the fault remediedby a workshop.


Vehicle personalisationThe vehicle's behaviour can bepersonalised by changing the settingsin the Info-Display.Depending on vehicle equipment andcountry-specific regulations some ofthe functions described below maynot be available.Some functions are only displayed oractive when the engine is running.

Personal settingsGraphic-Info-DisplayPress MENU to open the respectivemenu.Select Settings, scroll through the listand select Vehicle Settings

In the corresponding submenus thefollowing settings can be changed:

Vehicle Settings● Climate and Air Quality

Auto Fan Max Speed: Modifiesthe level of the cabin airflow of theclimate control in automaticmode.Auto Heated Seats:Automatically activates the seatheating.Auto Demist: Activates ordeactivates auto demist.Auto Rear Demist: Activates theheated rear windowautomatically.

● Park Assist / Collision DetectionPark Assist: Activates ordeactivates the ultrasonicsensors.

● Comfort SettingsChime Volume: Changes thevolume of warning chimes.Personalisation by Driver:Activates or deactivates thepersonalisation function.Rear Auto Wipe in Reverse:Activates or deactivatesautomatic switching on of the

rear window wiper when reversegear is engaged.

● Exterior Ambient LightingExterior lighting by unlocking:Activates or deactivates the entrylighting.Duration upon exit of vehicle:Activates or deactivates andchanges the duration of exitlighting.Left or Right Hand Traffic:Changes between lighting for leftor right-hand traffic.Adaptive Forward Lighting:Changes the settings of thefunctions of the LED headlights.

● Power Door LocksStop door lock if door open:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.


Delayed Door Lock: Activates ordeactivates the delayed doorlocking function.

● Remote Lock, Unlock, and StartRemote Unlock Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Auto Relock Doors: Activates ordeactivates the automatic relockfunction after unlocking withoutopening the vehicle.Remote Window Operation:Activates or deactivates theoperation of power windows withremote control.Passive Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.

Passive Door Lock: Activates ordeactivates the passive lockingfunction. This feature locks thevehicle automatically afterseveral seconds if all doors havebeen closed and an electronickey has been removed from thevehicle.Remote Left in Vehicle Alarm:Activates or deactivates thewarning chime when theelectronic key remains in thevehicle.

● Restore Factory Settings:Resets all settings to the defaultsettings.

Personal settings7" Colour-Info-DisplayPress ;, select Settings and thenVehicle on the touch-screen.


Vehicle● Climate & Air Quality

Auto Fan Max Speed: Modifiesthe level of the cabin airflow of theclimate control in automaticmode.Auto Heated Seats:Automatically activates the seatheating.Auto Defog: Activates ordeactivates auto demist.


Auto Rear Defog: Activates theheated rear windowautomatically.

● Collision / Detection SystemsPark Assist: Activates ordeactivates the ultrasonicsensors.

● Comfort and ConvenienceChime Volume: Changes thevolume of warning chimes.Personalization By Driver:Activates or deactivates thepersonalisation function.Auto Wipe in Reverse Gear:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● LightingVehicle Locator Lights: Activatesor deactivates the entry lighting.Exit Lighting: Activates ordeactivates and changes theduration of exit lighting.Left or Right Hand Traffic:Changes between lighting for leftor right-hand traffic.

Adaptive Forward Lighting:Changes the settings of thefunctions of the LED headlights.

● Power Door LocksUnlocked Door Anti Lock Out:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.Delayed Door Lock: Activates ordeactivates the delayed doorlocking function.

● Remote Lock, Unlock, StartRemote Unlock Light Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.

Relock Remotely UnlockedDoors: Activates or deactivatesthe automatic relock functionafter unlocking without openingthe vehicle.Remote Window Operation:Activates or deactivates theoperation of power windows withremote control.Passive Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Passive Door Lock: Activates ordeactivates the passive lockingfunction. This feature locks thevehicle automatically afterseveral seconds if all doors havebeen closed and an electronickey has been removed from thevehicle.Remote Left in Vehicle Alert:Activates or deactivates thewarning chime when theelectronic key remains in thevehicle.

Personal settings8" Colour-Info-Display


Press ; then select the SETTINGSicon.


Vehicle● Climate and Air Quality

Auto Fan Speed: Modifies thelevel of the cabin airflow of theclimate control in automaticmode.Auto Heated Seats:Automatically activates the seatheating.Auto Demist: Activates ordeactivates auto demist.

Auto Rear Demist: Activates theheated rear windowautomatically.

● Collision / Detection SystemsPark Assist: Activates ordeactivates the ultrasonicsensors.

● Comfort and ConvenienceChime Volume: Changes thevolume of warning chimes.Personalisation by Driver:Activates or deactivates thepersonalisation function.Auto Wipe in Reverse Gear:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● LightingVehicle Locator Lights: Activatesor deactivates the entry lighting.Exit Lighting: Activates ordeactivates and changes theduration of exit lighting.Left or Right Hand Traffic:Changes between lighting for leftor right-hand traffic.

Adaptive Forward Lighting:Changes the settings of thefunctions of the LED headlights.

● Power Door LocksUnlocked Door Anti-Lockout:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.Delayed Door Lock: Activates ordeactivates the delayed doorlocking function. This featuredelays the actual locking of thedoors until all doors are closed.

● Remote Lock, Unlock, StartRemote Unlock Light Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock only


the driver's door or the wholevehicle whilst unlocking.Relock Remote Unlocked Doors:Activates or deactivates theautomatic relock function afterunlocking without opening thevehicle.Remote Window Operation:Activates or deactivates theoperation of power windows withremote control.Passive Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Passive Door Lock: Activates ordeactivates the passive lockingfunction. This feature locks thevehicle automatically afterseveral seconds if all doors havebeen closed and an electronickey has been removed from thevehicle.Remote Left in Vehicle Alert:Activates or deactivates thewarning chime when theelectronic key remains in thevehicle.

Telematics serviceOnStarOnStar is a personal connectivity andservice assistant with integratedWi-Fi hotspot. The OnStar service isavailable 24 hours a day, seven daysa week.NoticeOnStar is not available for allmarkets. For further information,contact your workshop.NoticeIn order to be available andoperational, OnStar needs a validOnStar subscription, functioningvehicle electrics, mobile service andGPS satellite link.

To activate the OnStar services andset up an account, press Z and speakwith an advisor.

Depending on the equipment of thevehicle, the following services areavailable:● Emergency services and support

in the case of a vehiclebreakdown

● Wi-Fi hotspot● Smartphone application● Remote control, e.g. location of

the vehicle, activation of horn andlights, control of central lockingsystem

● Stolen vehicle assistance● Vehicle diagnostics● Destination downloadNoticeThe OnStar module of the vehicle isdeactivated after ten days without anignition cycle. Functions requiring adata connection will be availableagain after switching on the ignition.


OnStar buttons

Privacy buttonPress and hold j until a message isheard to activate or deactivate thetransmission of the vehicle location.Press j to answer a call or to end acall to an advisor.Press j to access the Wi-Fi settings.

Service buttonPress Z to establish a connection toan advisor.

SOS buttonPress [ to establish a priorityemergency connection to a speciallytrained emergency advisor.

Status LEDGreen: The system is ready withactivated transmission of the vehiclelocation.Green flashing: The system is on acall.Red: A problem arose.Off: The system is ready withdeactivated transmission of thevehicle location or the system is instandby mode.Red / green flashing for a short periodof time: The transmission of thevehicle location has beendeactivated.

OnStar services

General servicesIf you need any information e.g.opening hours, points of interest anddestinations or if you need anysupport e.g. in the case of a vehicle

breakdown, a flat tyre and empty fueltank, press Z to establish aconnection to an advisor.

Emergency servicesIn the case of an emergency situation,press [ and talk to an advisor. Theadvisor then contacts emergency orassistance service providers anddirects them to your vehicle.In the case of an accident withactivation of airbags or belttensioners, an automatic emergencycall is established. The advisor isimmediately connected to yourvehicle to see whether help isneeded.

Wi-Fi hotspotThe Wi-Fi hotspot of the vehicleprovides internet connectivity with amaximum speed of 4G/LTE.NoticeThe Wi-Fi hotspot functionality is notavailable for all markets.

Up to seven devices may beconnected.


To connect a mobile device with theWi-Fi hotspot:1. Press j and then select Wi-Fi

settings on the Info-Display. Thesettings displayed include the Wi-Fi hotspot name (SSID),password and connection type.

2. Start a Wi-Fi network search onyour mobile device.

3. Select your vehicle hotspot(SSID) when listed.

4. When prompted, enter thepassword on your mobile device.

NoticeTo change the SSID or password,press Z and talk to an advisor or login to your account.

To switch off the Wi-Fi hotspotfunctionality, press Z to call anadvisor.

Smartphone appWith the My Vauxhall smartphoneapp, some vehicle functions can beoperated remotely.

The following functions are available:● Lock or unlock vehicle.● Honk horn or flash lights.● Check fuel level, engine oil life

and tyre pressure (only with tyrepressure monitoring system).

● Send navigation destination tothe vehicle, if equipped with abuilt-in navigation system.

● Locate vehicle on a map.● Manage Wi-Fi settings.

To operate these functions, downloadthe app from App Store® orGoogle Play™ Store.

Remote controlIf desired, use any phone to call anadvisor, who can remotely operatespecific vehicle functions. Find therespective OnStar phone number onour country-specific website.The following functions are available:● Lock or unlock vehicle.● Provide information on the

vehicle location.● Honk horn or flash lights.

Stolen vehicle assistanceIf the vehicle is stolen, report the theftto the authorities and request OnStarstolen vehicle assistance. Use anyphone to call an advisor. Find therespective OnStar phone number onour country-specific website.OnStar can provide support inlocating and recovering the vehicle.Theft alertWhen the anti-theft alarm system istriggered, a notification is sent toOnStar. You are then informed aboutthis event by text message or email.Restart preventionBy sending remote signals, OnStarcan prevent the vehicle fromrestarting once it has been turned off.

On-demand diagnosticsAt any time e.g. if the vehicle displaysa vehicle message, press Z tocontact an advisor and ask tocomplete a real-time diagnostic checkto directly determine the issue.Depending on the results, the advisorwill provide further support.


Diagnostic reportThe vehicle automatically transmitsdiagnostic data to OnStar whichsends a monthly email report to youand your preferred workshop.NoticeThe workshop notification functioncan be disabled in your account.

The report contains the status of keyoperating systems of the vehicle likeengine, transmission, airbags, ABS,and other major systems. It alsoprovides information on possiblemaintenance items and tyre pressure(only with tyre pressure monitoringsystem).To look at the information in greaterdetail, select the link within the emailand log in to your account.

Destination downloadA desired destination can be directlydownloaded to the navigation system.Press Z to call an advisor anddescribe the destination or point ofinterest.

The advisor can look up any addressor point of interest and directly sendthe destination to the built-innavigation system.

OnStar settings

OnStar PINTo have full access to all OnStarservices, a four-digit PIN is required.The PIN has to be personalised whenfirst talking to an advisor.To change the PIN, press Z to call anadvisor.

Account dataAn OnStar subscriber has an accountwhere all the data is stored. Torequest a change of the accountinformation, press Z and talk to anadvisor or log in to your account.If the OnStar service is used onanother vehicle, press Z and requestthat the account be transferred to thenew vehicle.

NoticeIn any case, if the vehicle is disposedof, sold or otherwise transferred,immediately inform OnStar aboutthe changes and terminate theOnStar service on this vehicle.

Vehicle locationThe vehicle location is transmitted toOnStar when service is requested ortriggered. A message on the Info-Display informs about thistransmission.To activate or deactivate thetransmission of the vehicle location,press and hold j until an audiomessage is heard.The deactivation is indicated by thestatus light flashing red and green fora short period of time and each timethe vehicle is started.NoticeIf the transmission of the vehiclelocation is deactivated, someservices are no longer available.


NoticeThe vehicle location always remainsaccessible to OnStar in the case ofan emergency.

Find the privacy policy in youraccount.

Software updatesOnStar may remotely carry outsoftware updates without furthernotice or consent. These updates areto enhance or maintain safety andsecurity or the operation of thevehicle.These updates may concern privacyissues. Find the privacy policy in youraccount.

ERA GLONASSERA GLONASS is a manually orautomatically actuated emergencyservice. Emergency centres provideassistance and information during anemergency.In case of an accident with activationof airbags or belt tensioners, anemergency call is placedautomatically. An immediate

connection with an advisor will beestablished who will check whetherhelp is needed.

9 Danger

The service is only available formarkets where it is legally requiredand activated. Furthermore, themanual and the automaticemergency call function dependon the availability of theemergency centres and theinfrastructure in the country.

NoticeIn order to be available andoperational, the system requiresfunctioning vehicle electrics, mobileservice and GLONASS satellite link.Depending on equipment, a backupbattery is used.

Control buttons

SOS button KPress K and after a prompt pressagain to establish an emergencyconnection.

TECT button JPress J for cancellation of a call or forservice (technician use only).

Status LEDThe system provides feedback viavoice messages and an LED.


Green : The system is ready orwithin the recall time,during which the advisorcan call back after anestablished connection(up to approx. two hours,also possible with ignitionoff).

Greenflashing

: The system is dialling,data transmitting or avoice connection isestablished.

Red : The system is booting upfor maximum 15 secondsafter switching on ignition,then the LED turns green.If the LED stays red orturns from green to red, aproblem arose seek theassistance of a workshop.

Redflashing

: Call is not possible, e.g.because of unavailablemobile network.

Red/greenflashing

: System is in test mode.Do not press any buttonand wait until time-out.

Off : System is off.

NoticeIn very cold conditions it may take awhile to warm up the backup battery.When operational, the red LED turnsgreen.

Seek the assistance of a workshop ifthe LED does not illuminate afterswitching on the ignition.

114 Lighting

Lighting

Exterior lighting .......................... 114Light switch .............................. 114Automatic light control ............. 115High beam ............................... 115High beam assist ..................... 116Headlight flash ......................... 116Headlight range adjustment .... 117Headlights when drivingabroad .................................... 117

Daytime running lights ............. 118Adaptive forward lighting ......... 118Hazard warning flashers .......... 120Turn and lane-change signals . 121Front fog lights ......................... 121Rear fog light ........................... 121Reversing lights ....................... 121Misted light covers ................... 122

Interior lighting ........................... 122Instrument panel illuminationcontrol ..................................... 122

Interior lights ............................ 122Reading lights .......................... 123Glove box lighting .................... 123Sunvisor lights ......................... 123

Lighting features ........................ 123Entry lighting ............................ 123Exit lighting .............................. 124Battery discharge protection .... 124

Exterior lightingLight switch

Turn light switch:m : lights off8 : sidelights9 : low beam

Control indicator 8 3 95.

Lighting 115

Light switch with Automatic lightcontrol

Turn light switch:AUTO : automatic light control:

exterior lighting is switchedon and off automaticallydepending on externallighting conditions

m : activation or deactivation ofthe automatic light control.Switch turns back to AUTO

8 : sidelights9 : low beam

Tail lightsTail lights are illuminated togetherwith low beam and sidelights.

Automatic light control

When the automatic light controlfunction is switched on and theengine is running, the systemswitches between daytime runninglights and headlights automaticallydepending on the external lightingconditions and information given bythe rain sensor system.Daytime running light 3 118.

Automatic headlight activationDuring poor lighting conditions theheadlights are switched on.The headlights are also switched onif the windscreen wipers have beenactivated for several wipes.

Tunnel detectionWhen a tunnel is entered headlightsare switched on immediately.Adaptive forward lighting 3 118.

High beam

Push lever to switch from low to highbeam.

116 Lighting

Pull lever to deactivate high beam.High beam assist 3 118.

High beam assistThis feature allows high beam tofunction as the main driving light atnight and when vehicle speedexceeds 25 mph.It switches automatically to low beamwhen:● The camera or a sensor in the

windscreen detects the lights ofoncoming or preceding vehicles.

● The vehicle speed drops below12 mph.

● It is foggy or snowy.● Driving in urban areas.

If there are no restrictions detected,the system switches back to highbeam.

Activation

The high beam assist is activated bypushing the indicator lever twice. Thehigh beam is switched onautomatically at a speed above25 mph.The green control indicator filluminates continuously when theassist is activated, the blue one 7illuminates when high beam is on.Control indicator f 3 95.

DeactivationPush indicator lever once. It is alsodeactivated when front fog lights areswitched on.

If a headlight flash is activated whenthe high beam is on, the high beamassist will be deactivated.If a headlight flash is activated whenthe high beam is off, the high beamassist will remain activated.The latest setting of the high beamassist will remain after the ignition isswitched on again.

Headlight flashPull lever to activate the headlightflash.Pulling lever deactivates high beam.AFL-LED headlights 3 118.

Lighting 117

Headlight range adjustmentManual headlight rangeadjustment

To adapt headlight range to thevehicle load to prevent dazzling: turnthumb wheel ? to required position.0 : front seats occupied1 : all seats occupied2 : all seats occupied and load

compartment laden3 : driver's seat occupied and load

compartment laden

Dynamic automatic headlightlevelling 3 118.

Headlights when drivingabroadThe asymmetrical headlight beamextends visibility at the edge of theroad at the passenger side.However, when driving in countrieswhere traffic drives on the oppositeside of the road, adjust the headlightsto prevent dazzling of oncomingtraffic.

Vehicles with halogen headlightsystem

The adjusting screws are locatedabove the headlight.

Turn the adjusting screws with thescrewdriver clockwise by half a turn.To reset to left-hand traffic mode, turnadjuster elements on both headlighthousings anticlockwise by half a turn.

Caution

Have the adjustment of theheadlights checked afterdeactivation.We recommend consulting aworkshop.

118 Lighting

Vehicles with adaptive forwardlighting system

1. Key in ignition switch.2. Pull turn signal lever and hold

(headlight flash).3. Switch on ignition.4. After approx. five seconds the

control indicator f starts flashingand an acoustic signal sounds.

On another version the headlights areadjusted for driving on the oppositeside of the road via the vehiclepersonalisation menu. Select therelevant setting in Settings, I Vehicle.Vehicle personalisation 3 104.

Every time the ignition is switched on,control indicator f flashes as areminder for approx. four seconds.For deactivation, operate the sameprocedure as described above.Control indicator f will not flash whenfunction is deactivated.Control indicator f 3 95.

Daytime running lightsDaytime running lights increasevisibility of the vehicle during daylight.They are switched on automaticallyduring daytime when engine isrunning.The system switches betweendaytime running lights and headlightsautomatically, depending on thelighting conditions. Automatic lightcontrol 3 115.

Adaptive forward lightingThe Adaptive forward lightingfunctions are only available with LEDheadlights for low and high beam.Light range, light distribution andintensity of light are variably triggereddepending on the lighting conditions,road type and driving situation.

LED headlights for low and highbeamLED headlights for low and high beamensure better visibility under allconditions.Operation is the same as for halogenheadlights.Light switch 3 114, high beam 3 115,headlight flash 3 116, headlightswhen driving abroad 3 117.Automatic light control 3 115.

AFL-LED lighting functionsAFL-LED lighting functions are activeautomatically with light switch inposition AUTO. AFL-LED includesfollowing functions:

Lighting 119

● curve and cornering lights● town light● country light● motorway light● high beam assist● reverse parking function● eco mode● dynamic automatic headlight

levelling

Curve and cornering lights

On tight bends or when turning off,depending on the steering angle orthe indicator light signal, an additionalleft or right reflector is switched onwhich illuminates the road in thedirection of travel. It is activated up toa speed of 43 mph.

Town light

Activated automatically at a speed upto approx. 34 mph. In situations withexterior ambient light both corneringlights are switched on with reducedintensity. The light is wide andsymmetrical.

Country lightActivated automatically at a speedrange between approx. 33 and112 mph. The beam of light and thebrightness is different between theleft and the right side.

Motorway lightActivated automatically at a speedabove approx. 112 mph and minimalsteering movements. It switches onafter a delay or directly when thevehicle is powerfully accelerated. Thelight beam is longer and brighter.

High beam assistThis feature allows high beam tofunction as the main driving light atnight and when vehicle speedexceeds 25 mph.It switches automatically to low beamwhen:● The camera or a sensor in the

windscreen detects the lights ofoncoming or preceding vehicles.

● The vehicle speed drops below12 mph.

● It is foggy or snowy.● Driving in urban areas.

If there are no restrictions detected,the system switches back to highbeam.

120 Lighting

Activation

The high beam assist is activated bypushing the indicator lever twice. Thehigh beam is switched onautomatically at a speed above25 mph.The green control indicator filluminates continuously when theassist is activated, the blue one 7illuminates when high beam is on.Control indicator f 3 95.

DeactivationPush indicator lever once. It is alsodeactivated when front fog lights areswitched on.

If a headlight flash is activated whenthe high beam is on, the high beamassist will be deactivated.If a headlight flash is activated whenthe high beam is off, the high beamassist will remain activated.The latest setting of the high beamassist will remain after the ignition isswitched on again.

Reverse parking functionTo assist driver's orientation whenparking, both corner lights andreversing light illuminate whenheadlights are on and reverse gear isengaged. They remain illuminated fora short time after disengaging reversegear or until driving faster than4 mph in a forward gear.

Eco modeIf the vehicle stops, e. g. due to trafficlights, an energy saving mode forheadlights is activated.

Dynamic automatic headlightlevellingTo prevent oncoming traffic frombeing dazzled, headlight levelling isautomatically adjusted based onvehicle inclination information.

Fault in AFL-LED lighting systemWhen the system detects a failure inthe LED headlight system, filluminates and a warning is displayedin the Driver Information Centre.

Hazard warning flashers

Operated by pressing ¨.

Lighting 121

Turn and lane-changesignals

lever up : right turn signallever down : left turn signal

If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.For three flashes, e.g. when changinglanes, press the lever until resistanceis felt and then release.

When a trailer is connected, turnsignal flashes six times whenpressing the lever until resistance isfelt and then releasing.Move the lever to the resistance pointand hold for longer indication.Switch the turn signal off manually bymoving the lever to its originalposition.

Front fog lights

Operated by pressing >.

Rear fog light

Operated by pressing ø.Light switch in position AUTO:switching on rear fog light will switchheadlights on automatically.Light switch in position 8: rear foglight can only be switched on withfront fog lights.

Reversing lightsThe reversing light comes on whenthe ignition is on and reverse gear isselected.

122 Lighting

Misted light coversThe inside of the light housing maymist up briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help switch on theheadlights.

Interior lightingInstrument panelillumination control

Brightness of the following lights canbe adjusted when the exterior lightsare on:● instrument panel illumination● steering wheel controls

Turn thumb wheel A and hold untilthe desired brightness is obtained.

Interior lightsCourtesy light

Front

Operate rocker switch:press v : offw : automatic switching on

and offpress u : on

Lighting 123

Rear

Operate rocker switch:⃒ : onw : automatic switching on and off§ : off

Reading lights

The front reading lights are located inthe overhead console.Press s and t to turn each light onor off.

Glove box lightingIlluminates when the glovebox isopened.

Sunvisor lightsIlluminates when the cover is opened.

Lighting featuresEntry lightingWelcome lightingFollowing lights are switched on for ashort time by unlocking the vehiclewith the radio remote control:● low beam● sidelights● tail lights● number plate lights● instrument panel light● interior lights

This function works only in the darkand facilitates locating the vehicle.Activation or deactivation of thisfunction can be changed in thevehicle settings. Vehiclepersonalisation 3 104.The following lights will additionallyswitch on when driver's door isopened:● illumination of some switches● some interior lights

124 Lighting

Exit lightingLow beam, sidelights and tail lightsilluminate the surrounding area for anadjustable time after leaving thevehicle.

Switching onActivation, deactivation and durationof lighting of this function can bechanged in the vehicle settings.Vehicle personalisation 3 104.

1. Switch off ignition.2. Remove ignition key.3. Open driver's door.

4. Pull turn signal lever.5. Close driver's door.

If the driver's door is not closed thelights switch off after a few seconds.The lighting is switched offimmediately if the turn signal lever ispulled while the driver's door is open.

Battery discharge protectionTo prevent discharge of the batterywhen the ignition is switched off,some interior lights are switched offautomatically after some time.

Climate control 125

Climate control

Climate control systems ............. 125Heating and ventilation system 125Air conditioning system ........... 126Electronic climate controlsystem .................................... 127

Auxiliary heater ........................ 129Air vents ..................................... 130

Adjustable air vents ................. 130Fixed air vents ......................... 130

Maintenance .............................. 130Air intake ................................. 130Pollen filter ............................... 130Air conditioning regularoperation ................................ 131

Service .................................... 131

Climate control systemsHeating and ventilationsystem

Controls for:● air distribution● temperature● fan speed● demisting and defrosting

Heated rear window Ü 3 35.

Temperaturered : warmblue : cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Air distributionl : to windscreen and front door

windowsM : to head areaK : to foot well and windscreen

Combination settings are possible.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Demisting and defrosting● Press V: fan automatically

switches to higher speed, the airdistribution is directed towardsthe windscreen.

● Set temperature control towarmest level.

● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

126 Climate control

Air conditioning system

In addition to the heating andventilation system, the airconditioning system has controls for:n : cooling4 : air recirculation

Cooling nPress n to switch on cooling. TheLED in the button illuminates toindicate activation. Cooling is onlyfunctional when the engine is runningand climate control fan is switched on.Press n again to switch off cooling.

The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is above aspecific level. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch off the cooling system for fuelsaving reasons. Activated coolingmay inhibit Autostops.Stop-start system 3 137.

Air recirculation system 4Press 4 to activate air recirculationmode. The LED in the buttonilluminates to indicate activation.Press 4 again to deactivate airrecirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passenger

compartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside when cold air isdirected towards it. If windscreenmists up from outside, activatewindscreen wiper and deactivate l.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.● Switch on cooling n.● Air recirculation system 4 on.● Press air distribution switch M.● Set temperature control to

coldest level.● Set fan speed to highest level.● Open all vents.

Climate control 127

Demisting and defrosting thewindows V● Press V: fan automatically

switches to higher speed, the airdistribution is directed towardsthe windscreen.

● Set temperature control towarmest level.

● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If l is pressed with the fan switchedon and the engine running, anAutostop will be inhibited until l ispressed again or until the fan isswitched off.

If V is pressed while the engine isin an Autostop, the engine will restartautomatically.If l is pressed with the fan switchedon while the engine is in anAutostop, the engine will restartautomatically.

Stop-start system 3 137.

Electronic climate controlsystem

Controls for:● air distribution● temperature● fan speed

AUTO : automatic mode4 : manual air recirculationV : demisting and defrosting

Heated rear window Ü 3 35.The preselected temperature isautomatically regulated. In automaticmode, the fan speed and airdistribution automatically regulate theair flow.The system can be manually adaptedvia the use of air distribution and airflow controls.Each change of settings is shown inthe Info-Display for a few seconds.The electronic climate control systemis only fully operational when theengine is running.

128 Climate control

Automatic mode AUTOBasic setting for maximum comfort:● Press AUTO: the air distribution

and fan speed are regulatedautomatically.

● Open all air vents.● Press n to switch on cooling.● Set the desired temperature.

Temperature preselectionTemperatures can be set to thedesired value.If the minimum temperature is set, theclimate control system runs atmaximum cooling.If the maximum temperature is set,the climate control system runs atmaximum heating.NoticeIf the temperature is to be reducedfor climate comfort reasons, anAutostop may be inhibited or theengine will restart automaticallywhen cooling is switched on.Stop-start system 3 137.

The temperature can be adjustedseparately for driver and frontpassenger side.

Demisting and defrosting thewindows V● Press V.● Temperature and air distribution

are set automatically and the fanruns at high speed.

● Switch on heated rear window Ü.● To return to previous mode:

press V, to return to automaticmode: press AUTO.

NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If l is pressed with the fan switchedon and the engine running, anAutostop will be inhibited until l ispressed again or until the fan isswitched off.

If V is pressed while the engine isin an Autostop, the engine will restartautomatically.If l is pressed with the fan switchedon while the engine is in anAutostop, the engine will restartautomatically.

Stop-start system 3 137.

Manual settingsClimate control system settings canbe changed by activating the buttonsand rotary knobs as follows.Changing a setting will deactivate theautomatic mode.

Fan speed ZThe selected fan speed is indicatedwith x and a number in the display. Ifthe fan is switched off, the airconditioning is also deactivated.To return to automatic mode: PressAUTO.

Air distribution l, M, KPress appropriate button for desiredadjustment. The LED in the buttonilluminates to indicate activation.

Climate control 129

l : to windscreen and front doorwindows (air conditioning isactivated in the background tohelp prevent windows fromfogging)

M : to head areaK : to foot well and windscreen

Combination of settings are possible.Return to automatic air distribution:Deactivate corresponding setting orpress AUTO.

Cooling nPress n to switch on cooling. TheLED in the button illuminates toindicate activation. Cooling is onlyfunctional when the engine is runningand climate control fan is switched on.Press n again to switch off cooling.The air conditioning system cools anddehumidifies (dries) when outsidetemperature is above a specific level.Therefore condensation may formand drip from under the vehicle.If no cooling or drying is required,switch off the cooling system for fuelsaving reasons. Activated coolingmay inhibit an Autostop.

Stop-start system 3 137.Eco appears in the display whencooling is deactivated.

Air recirculation mode 4Press 4 once to activate themanual air recirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

Air conditioning with the enginenot runningWhen ignition is off, the residual heator cooling in the system can be usedfor climate control in passengercompartment.

Auxiliary heaterAir heaterQuickheat is an electric auxiliary airheater which automatically warms upthe passenger compartment morequickly.

130 Climate control

Air ventsAdjustable air ventsAt least one air vent must be openwhile the cooling is on.

To open the vent, turn the adjusterwheel to the right. Adjust the airamount at the vent outlet by turningthe adjuster wheel.

Direct the flow of air by tilting andswivelling the slats.To close the vent, turn the adjusterwheel to the left.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake.Remove any leaves, dirt or snow.

Pollen filterThe pollen filter cleans dust, soot,pollen and spores from the airentering the vehicle through the airintake.

Climate control 131

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes once amonth, irrespective of the weatherand time of year. Operation withcooling is not possible when theoutside temperature is too low.

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, startingthree years after initial vehicleregistration, including:● functionality and pressure test● heating functionality● leakage check● check of drive belts● cleaning of condenser and

evaporator drainage● performance checkNoticeRefrigerant R-134a containsfluorinated greenhouse gases.

132 Driving and operating

Driving andoperating

Driving hints ............................... 133Control of the vehicle ............... 133Steering ................................... 133

Starting and operating ............... 133New vehicle running-in ............ 133Ignition switch positions ........... 134Power button ........................... 134Retained power off .................. 135Starting the engine .................. 136Overrun cut-off ........................ 137Stop-start system .................... 137Parking .................................... 139

Engine exhaust .......................... 140Diesel particle filter .................. 141Catalytic converter ................... 141

Automatic transmission .............. 142Transmission display ............... 142Selector lever .......................... 142Manual mode ........................... 143Electronic driving programmes 144Fault ........................................ 144Interruption of power supply .... 144

Manual transmission .................. 145

Drive systems ............................ 146All-wheel drive ......................... 146

Brakes ........................................ 147Antilock brake system ............. 147Parking brake .......................... 147Brake assist ............................. 148Hill start assist ......................... 148

Ride control systems ................. 148Traction Control system .......... 148Electronic Stability Control ...... 149Descent control system ........... 150

Driver assistance systems ......... 151Cruise control .......................... 151Speed limiter ........................... 153Forward collision alert ............. 154Following distance indication ... 156Parking assist .......................... 157Rear view camera ................... 159Traffic sign assistant ................ 160Lane departure warning .......... 164

Fuel ............................................ 165Fuel for petrol engines ............. 165Fuel for diesel engines ............ 165Fuel for liquid gas operation .... 166Refuelling ................................ 168Fuel consumption - CO2-Emissions .............................. 171

Trailer hitch ................................ 172General information ................. 172Driving characteristics andtowing tips .............................. 172

Trailer towing ........................... 172Towing equipment ................... 173

Driving and operating 133

Driving hintsControl of the vehicleNever coast with engine notrunning (except during Autostop)Many systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner is adanger to yourself and others. Allsystems function during an Autostop,but there will be a controlled reductionin power steering assist and vehiclespeed is reduced.Stop-start system 3 137.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.Use only floor mats, which fit properlyand are fixed by the retainers on thedriver side.

SteeringIf power steering assist is lostbecause the engine stops or due to asystem malfunction, the vehicle canbe steered but may require increasedeffort.A vehicle message will be displayedin the Info-Display.

Caution

Vehicles equipped with hydraulicpower steering:If the steering wheel is turned untilit reaches the end of its travel, andis held in that position for morethan 10 seconds, damage mayoccur to the power steeringsystem and there may be loss ofpower steering assist.

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open for awhile after the first drive and avoidinhaling the fumes.During the running-in period fuel andengine oil consumption may behigher and the cleaning process ofthe diesel particle filter may takeplace more often. Autostop may beinhibited to allow for charging thebattery.Diesel particle filter 3 141.


Ignition switch positions

0 : ignition off: Some functionsremain active until key isremoved or driver's door isopened, provided the ignition wason previously

1 : accessory power mode: Steeringwheel lock released, someelectrical functions are operable,ignition is off

2 : ignition on power mode: Ignitionis on, diesel engine is preheating.Control indicators illuminate andmost electrical functions areoperable

3 : engine start: Release key afterstarting procedure begins

Steering wheel lockRemove key from ignition switch andturn steering wheel until it engages.

9 Danger

Never remove the key fromignition switch during driving asthis will cause steering wheel lock.

Power button

Electronic key must be inside thevehicle.

Accessory power modePress Engine Start/Stop once withoutoperating clutch or brake pedal. Theyellow LED in the button illuminates.Steering wheel lock is released andsome electrical functions areoperable, ignition is off.Ignition on power modePress and hold Engine Start/Stop forsix seconds without operating clutchor brake pedal. The green LED in thebutton illuminates, diesel engine ispreheating. Control indicatorsilluminate and most electricalfunctions are operable.Engine startOperate clutch pedal (manualtransmission) or brake pedal(automatic transmission) and pressEngine Start/Stop once more.Release button after startingprocedure begins.Ignition offPress Engine Start/Stop briefly ineach mode or when engine is runningand vehicle is stationary. Somefunctions remain active until driver'sdoor is opened, provided the ignitionwas on previously.


Emergency shut off during drivingPress Engine Start/Stop for longerthan two seconds or press twicebriefly within five seconds 3 136.

Steering wheel lockThe steering wheel lock activatesautomatically when:● The vehicle is stationary.● The ignition has been switched

off.● The driver's door is opened.

To release steering wheel lock, openand close driver's door and switch onaccessory mode or start the enginedirectly.

9 Warning

If the vehicle battery is discharged,the vehicle must not be towed,tow-started or jump-started as thesteering wheel lock cannot bedisengaged.

Operation on vehicles withelectronic key system in case offailureIf either the electronic key fails or thebattery of the electronic key is weak,the Driver Information Centre maydisplay No Remote Detected orReplace Battery in Remote Key whenyou try to start the vehicle.

1. Place the electronic key in thefront cupholder of the centreconsole. Place the electronic keysolely centred in the transmitter

area in longitudinal direction flatwith buttons upside as shown inthe illustration.

2. With the vehicle in P (Park) or N(Neutral), depress the brakepedal and pressEngine Start/Stop.

Replace the transmitter battery assoon as possible.

Retained power offThe following electronic systems canwork up to ten minutes after theengine is turned off● Power windows● Sunroof● Audio system

The power windows and sunroof willcontinue to work for up to ten minutesor until any door is opened. The radiowill work in ignition on power modeand accessory power mode. Oncethe ignition is turned off, the radio willcontinue to work for ten minutes, oruntil the driver's door is opened.


Starting the engineVehicles with ignition switch

Turn key to position 1 to release thesteering wheel lock.Manual transmission: depress clutchand brake pedal.Automatic transmission: depressbrake pedal and move the selectorlever to P or N.Do not depress the accelerator pedal.Diesel engine: turn the key to position2 for preheating and wait until controlindicator ! extinguishes.

Turn the key briefly to position 3 andrelease: an automatic procedureoperates the starter with a short delayas long as the engine is running, see'Automatic Starter Control'.Manual transmission: during anAutostop, the engine can be restartedby depressing the clutch pedal3 137.Automatic transmission: during anAutostop, the engine can be restartedby releasing the brake pedal 3 137.

Vehicles with power button

Manual transmission: depress clutchand brake pedal.

Automatic transmission: depressbrake pedal and move selector leverto P or N.Do not depress accelerator pedal.Press and release Engine Start/Stop:an automatic procedure operates thestarter with a short delay until theengine is running, see automaticstarter control.Before restarting or to switch off theengine when vehicle is stationary,press Engine Start/Stop once morebriefly.Manual transmission: during anAutostop, the engine can be restartedby depressing the clutch pedal3 137.Automatic transmission: during anAutostop, the engine can be restartedby releasing the brake pedal 3 137.

Key lock releaseSome vehicles with an automatictransmission are equipped with anelectronic key lock release system.The key lock release is designed toprevent ignition key removal unlessthe selector lever is in P.


Starting the vehicle at lowtemperaturesStarting the engine without additionalheaters is possible down to -25 °С fordiesel engines and -30 °C for petrolengines. Required is an engine oilwith the correct viscosity, the correctfuel, performed services and asufficiently charged vehicle battery.With temperatures below -30 °C, theautomatic transmission requires awarming phase of approx.five minutes. The selector lever mustbe in position P.

Automatic Starter ControlThis function controls the enginestarting procedure. The driver doesnot need to hold the key in position 3or to hold Engine Start/Stop pressed.Once applied, the system will go onstarting automatically until the engineis running. Because of the checkingprocedure, the engine starts runningafter a short delay.

Possible reasons for a non-startingengine:● Clutch pedal not depressed

(manual transmission).● Brake pedal not depressed or

selector lever not in P or N(automatic transmission).

● Timeout occurred

Turbo engine warm-upUpon start-up, engine availabletorque may be limited for a short time,especially when the enginetemperature is cold. The limitation isto allow the lubrication system to fullyprotect the engine.

Overrun cut-offThe fuel supply is automatically cut offduring overrun, i.e. when the vehicleis driven with a gear engaged butaccelerator pedal is released.Depending on driving conditions, theoverrun cut-off may be deactivated.

Stop-start systemThe stop-start system helps to savefuel and to reduce the exhaustemissions. When conditions allow, itswitches off the engine as soon as thevehicle is at a low speed or at astandstill, e.g. at a traffic light or in atraffic jam. It starts the engineautomatically as soon as the clutch isdepressed. A battery sensor ensuresthat an Autostop is only performed ifthe battery is sufficiently charged fora restart.

ActivationThe stop-start system is available assoon as the engine is started, thevehicle starts-off and the conditionsas stated below in this section arefulfilled.


Deactivation

Deactivate the stop-start systemmanually by pressing Ï.Deactivation is indicated when theLED in the button extinguishes.

AutostopIf the vehicle is at a low speed or at astandstill, activate an Autostop asfollows:● Depress the clutch pedal.● Move the selector lever to

neutral.● Release the clutch pedal.

The engine will be switched off whilethe ignition stays on.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.During an Autostop, the heatingperformance, power steering andbrake performance will bemaintained.

Conditions for an AutostopThe stop-start system checks if eachof the following conditions is fulfilled:● The stop-start system is not

manually deactivated.● The bonnet is fully closed.

● The driver's door is closed or thedriver's seat belt is fastened.

● The vehicle battery is sufficientlycharged and in good condition.

● The engine is warmed up.● The engine coolant temperature

is not too high.● The engine exhaust temperature

is not too high, e.g. after drivingwith high engine load.

● The ambient temperature isabove -5 °C.

● The climate control systemallows an Autostop.

● The brake vacuum is sufficient.● The self-cleaning function of the

diesel particle filter is not active.● The vehicle was driven at least at

walking speed since the lastAutostop.

Otherwise an Autostop will beinhibited.Certain settings of the climate controlsystem may inhibit an Autostop. SeeClimate control chapter for moredetails 3 126.


Immediately after motorway drivingan Autostop may be inhibited.New vehicle running-in 3 133.

Vehicle battery discharge protectionTo ensure reliable engine restarts,several battery discharge protectionfeatures are implemented as part ofthe stop-start system.

Power saving measuresDuring an Autostop, several electricalfeatures such as auxiliary electricheater or rear window heating aredisabled or switched into a powersaving mode. The fan speed of theclimate control system is reduced tosave power.

Restart of the engine by the driverDepress the clutch pedal to restart theengine.The engine start is indicated by theneedle at the idle speed position inthe tachometer.If the selector lever is shifted out ofneutral before depressing the clutchfirst, - with a message is shown inthe Driver Information Centre.

Restart of the engine by the stop-start systemThe selector lever must be in neutralto enable an automatic restart.If one of the following conditionsoccurs during an Autostop, theengine will be restarted automaticallyby the stop-start system:● The stop-start system is

manually deactivated.● The bonnet is opened.● The driver's seat belt is

unfastened and the driver's dooris opened.

● The engine temperature is toolow.

● The charging level of the vehiclebattery is below a defined level.

● The brake vacuum is notsufficient.

● The vehicle is driven at least atwalking speed.

● The climate control systemrequests an engine start.

● The air conditioning is manuallyswitched on.

If the bonnet is not fully closed, awarning message is displayed in theDriver Information Centre.If an electrical accessory, e.g. aportable CD player, is connected tothe power outlet, a brief power dropduring engine restart might benoticeable.

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the parkingbrake without pressing therelease button. Apply as firmlyas possible on a downhill slopeor uphill slope. Depress brakepedal at the same time toreduce operating force.

● Switch off the engine.


● If the vehicle is on a levelsurface or uphill slope, engagefirst gear or set the selectorlever to position P beforeremoving the ignition key. Onan uphill slope, turn the frontwheels away from the kerb.If the vehicle is on a downhillslope, engage reverse gear orset the selector lever to positionP before removing the ignitionkey. Turn the front wheelstowards the kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch. For vehicleswith automatic transmission,the key can only be removedwhen the selector lever is inposition P.Turn the steering wheel untilthe steering wheel lock is felt toengage.

● Lock the vehicle.● Activate the anti-theft alarm

system.

NoticeIn the event of an accident withairbag deployment, the engine isturned off automatically if the vehiclecomes to a standstill within a certaintime.

Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.


Diesel particle filterAutomatic cleaning processThe diesel particle filter system filtersharmful soot particles out of theexhaust gases. The system includesa self-cleaning function that runsautomatically during driving withoutany notification. The filter is cleanedby periodically burning off the sootparticles at high temperature. Thisprocess takes place automaticallyunder set driving conditions and maytake up to 25 minutes. Typically itneeds between seven and twelveminutes. Autostop is not availableand fuel consumption may be higherduring this period. The emission ofsmells and smoke during this processis normal.

System requires manual cleaningprocessUnder certain driving conditions, e.g.short distances, the system cannotclean itself automatically.If cleaning of the filter is required andif previous driving conditions did notenable automatic cleaning, it will be

indicated by % and a warningmessage in the Driver InformationCentre.% with a warning messageilluminates when diesel particle filteris full. Start cleaning process as soonas possible.% with a warning message flasheswhen diesel particle filter has reachedthe maximum filling level. Startcleaning process immediately toavoid damage to the engine.

Activate manual cleaning processTo activate cleaning process,continue driving, keep engine speedabove 2000 revolutions per minute.Shift down if necessary. Dieselparticle filter cleaning is then started.Cleaning takes place quickest at highengine speeds and loads.The control indicator % extinguishesas soon as the self-cleaningoperation is complete. Keep ondriving until self-cleaning operation iscomplete.

Caution

If the cleaning process isinterrupted, there is a risk ofprovoking severe engine damage.

Cleaning process not possibleIf cleaning is not possible for anyreasons, Z illuminates and a warningmessage appears in the DriverInformation Centre. Engine powermay be reduced. Seek the assistanceof a workshop immediately.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.


Caution

Fuel grades other than those listedon pages 3 165, 3 224 coulddamage the catalytic converter orelectronic components.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the faultrectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.

Automatic transmissionThe automatic transmission permitsautomatic gearshifting (automaticmode) or manual gearshifting(manual mode).

Transmission display

The mode or selected gear is shownin the Driver Information Centre.In automatic mode, the drivingprogramme is indicated by D.In manual mode, M and the numberof the selected gear is indicated.R indicates reverse gear.

N indicates neutral position.P indicates park position.

Selector lever

P : park position, wheels are locked,engage only when the vehicle isstationary and the parking brakeis applied

R : reverse gear, engage only whenthe vehicle is stationary

N : neutralD : automatic modeM : manual mode< : upshift in manual mode] : downshift in manual mode


The selector lever is locked in P andcan only be moved when the ignitionis on and the brake pedal is applied.

To engage P or R, press the releasebutton.The engine can only be started withthe lever in position P or N. Whenposition N is selected, press the brakepedal or apply the parking brakebefore starting.Do not accelerate while engaging agear. Never depress the acceleratorpedal and brake pedal at the sametime.

When a gear is engaged, the vehicleslowly begins to creep when thebrake is released.

Engine brakingTo utilise the engine braking effect,select a lower gear in good time whendriving downhill, see manual mode.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between D and R in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingApply the parking brake and engageP.The ignition key can only be removedwhen the selector lever is in positionP.

Manual mode

Move selector lever to position M.Press button on the selector lever:< : shift to a higher gear

] : shift to a lower gear

If a higher gear is selected whenvehicle speed is too low, or a lowergear when vehicle speed is too high,the shift is not executed. This cancause a message in the DriverInformation Centre.In manual mode no automatic shiftingto a higher gear takes place at highengine revolutions.


Gear shift indicationThe symbol R with a number besideit is indicated when gearshifting isrecommended for fuel savingreasons.Shift indication appears only inmanual mode.

Electronic drivingprogrammes● Following a cold start, the

operating temperatureprogramme increases enginespeed to quickly bring thecatalytic converter to the requiredtemperature.

● The automatic neutral shiftfunction automatically shifts toidling when the vehicle is stoppedwith a forward gear engaged andthe brake pedal is pressed.

● Special programmesautomatically adapt the shiftingpoints when driving up inclines ordown hills.

Automatic transmissionadaptation featureThis feature adapts transmissionoperation during constant driving orgear shifting. It increases durabilityand keeps best shift quality over thelife cycle. You may perceive shiftingat initial mileage as uncomfortable,but this is normal. Shift quality will beimproved gradually by constantdriving at each gear and gear shifting.

KickdownIf the accelerator pedal is presseddown completely in automatic mode,the transmission shifts to a lower geardepending on engine speed.

FaultIn the event of a fault, a vehiclemessage is displayed in the DriverInformation Centre. Vehiclemessages 3 102.The transmission no longer shiftsautomatically. Continued travel ispossible with manual shifting.

Only the highest gear is available.Depending on the fault, second gearmay also be available in manualmode. Shift only when vehicle is at astandstill.Have the cause of the fault remediedby a workshop.

Interruption of power supplyIn the event of an interruption ofpower supply, the selector levercannot be moved out of the Pposition. The ignition key cannot beremoved from the ignition switch.If the battery is discharged, start thevehicle using jump leads 3 209.If the battery is not the cause of thefault, release the selector lever.1. Keep the brake pedal depressed

and pull the parking brake leverup.


2. Remove the cap on the consolewith a thin object such as ascrewdriver.

3. Insert a screwdriver into theopening as far as it will go.

4. Shift selector lever to N.5. Remove the screwdriver from the

slot.6. Reinstall the cap.7. Have the cause of the power

supply interruption remedied by aworkshop.

Manual transmission

To engage reverse, with the vehiclestationary, depress clutch pedal,press the release button on theselector lever and engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Do not slip the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.


Caution

It is not advisable to drive with thehand resting on the selector lever.

Gear shift indication 3 93.Stop-start system 3 137.

Drive systemsAll-wheel driveThe All-Wheel Drive (AWD) systemenhances driving characteristics andstability, and helps to achieve the bestpossible driveability regardless ofground surface. The system is alwaysactive and cannot be deactivated.The torque is distributed steplesslybetween the wheels of the front andrear axle, depending on the drivingconditions. Additionally the torquebetween the rear wheels is distributeddepending on the surface.For optimum system performance,the vehicle's tyres should not havevarying degrees of wear.When using a temporary sparewheel, the AWD system isautomatically disabled.The AWD system will also betemporarily disabled to protect thesystem from overheating if there isexcessive wheel spin. When thesystem cools down, AWD will berestored.

The deactivation of the AWD systemwill be indicated by a message on theDriver Information Centre.If a service message or warningcode S73 is displayed on the DriverInformation Centre, there is amalfunction in the AWD system. Seekthe assistance of a workshop.Vehicle messages 3 102, Towing thevehicle 3 211.


BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when the brake pedalis depressed firmly. Considerablymore force is needed for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing the journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator R 3 92.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparentthrough a pulse in the brake pedaland the noise of the regulationprocess.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.After starting-off the system performsa self-test which may be audible.Control indicator u 3 92.

Adaptive brake lightDuring full braking, all three brakelights flash for the duration of ABScontrol.

Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.

Parking brake


9 Warning

Always apply parking brake firmlywithout operating the releasebutton, and apply as firmly aspossible on a downhill or uphillslope.To release the parking brake, pullthe lever up slightly, press therelease button and fully lower thelever.To reduce the operating forces ofthe parking brake, depress thebrake pedal at the same time.

Control indicator R 3 92.

Brake assistIf the brake pedal is depressedquickly and forcefully, maximumbrake force is automatically applied(full braking).Maintain steady pressure on thebrake pedal for as long as full brakingis required. Maximum brake force isautomatically reduced when thebrake pedal is released.

Hill start assistThe system helps prevent unintendedmovement when driving away oninclines.When releasing the brake pedal afterstopping on an incline, the brakesremain on for a further two seconds.The brakes release automatically assoon as the vehicle begins toaccelerate.The hill start assist is not active duringan Autostop.Stop-start system 3 137.

Ride control systemsTraction Control systemThe Traction Control system (TC) is acomponent of the Electronic StabilityControl (ESC) 3 149.TC improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip, bypreventing the drive wheels fromspinning.As soon as the drive wheels starts tospin, engine output is reduced andthe wheel spinning the most is brakedindividually. This considerablyimproves the driving stability of thevehicle on slippery road surfaces.

TC is operational after each enginestart as soon as the control indicatorb extinguishes.When TC operates b flashes.


9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 93.

Deactivation

TC can be switched off when spinningof drive wheels is required: press bbriefly.

Control indicator k illuminates.A status message appears in theDriver Information Centre when TC isdeactivated.When TC is deactivated, ESCremains active but with higher controlthreshold.TC is reactivated by pressing bagain. A status message pops up inthe Driver Information Centre whenTC is reactivated.TC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a message appearsin the Driver Information Centre. Thesystem is not operational.

Have the cause of the fault remediedby a workshop.

Electronic Stability ControlElectronic Stability Control (ESC)improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually.ESC operates in combination with theTraction Control system (TC). Itprevents the drive wheels fromspinning.

ESC is operational after each enginestart as soon as the control indicatorb extinguishes.When ESC operates b flashes.


9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 93.

Deactivation

ESC can be deactivated: press andhold t for approx. five seconds.Control indicators k and n illuminate.

ESC is reactivated by pressing tagain. If the TC system waspreviously disabled, both TC andESC are reactivated.ESC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a message appearsin the Driver Information Centre. Thesystem is not operational.Have the cause of the fault remediedby a workshop.

Descent control systemThe Descent control system (DCS)allows the vehicle to travel at a lowspeed without depressing the brakepedal. The vehicle will automaticallydecelerate to a low speed and remainat that speed when the system isactivated. Some noise or vibrationfrom the brake system may beapparent when the system is active.

Caution

Use only when descending steepgrades while driving off-road. Donot use when driving on normalroad surfaces. Unnecessaryusage of the DCS function, suchas while driving on normal roads,may damage the brake systemand the ESC function.

Activation

At speeds below approx. 25 mph,press u. The green control indicatoru flashes in the instrument cluster, to


show DCS is in operation. DCS willnot activate at speeds above30 mph, even if the button is pressed.

DeactivationPress u again. The green controlindicator u extinguishes. Depressingthe foot brake or accelerator will alsocause the system to be deactivated.

FaultIf the green control indicator u doesnot illuminate or flash after pressingthe button, there is a fault in thesystem.Seek the assistance of a workshop.DSC control indicators u 3 93.

Driver assistancesystems

9 Warning

Driver assistance systems aredeveloped to support the driverand not to replace the driver'sattention.The driver accepts fullresponsibility when driving thevehicle.When using driver assistancesystems, always take careregarding the current trafficsituation.

Cruise controlThe Cruise control can store andmaintain speeds of approx. 20 to120 mph. Deviations from the storedspeeds may occur when driving uphillor downhill.For safety reasons, the cruise controlcannot be activated until the brakepedal has been operated once.Activating in first gear is not possible.

Do not use the cruise control if it is notadvisable to maintain a constantspeed.With automatic transmission, onlyactivate cruise control in automaticmode.Control indicator m 3 95.

Switching on


Press m: control indicator m ininstrument cluster illuminates white.

Activation

Accelerate to the desired speed andturn thumb wheel to SET/-: thecurrent speed is stored andmaintained. Control indicator m ininstrument cluster illuminates green.On Uplevel display m illuminatesgreen and set speed is indicated.Accelerator pedal can be released.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.Cruise control remains activatedwhile gearshifting.

Increase speedWith cruise control active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly: speedincreases continuously or in smallincrements.Alternatively accelerate to the desiredspeed and store by turning to SET/-.

Reduce speedWith cruise control active, hold thumbwheel turned to SET/- or briefly turn toSET/- repeatedly: speed decreasescontinuously or in small increments.

DeactivationPress y: control indicator m ininstrument cluster illuminates white.On Uplevel display m changes towhite.Cruise control is deactivated, but notswitched off. Last stored speedremains in memory for later speedresume.Automatic deactivation:● Vehicle speed is below approx.

20 mph.● Vehicle speed drops more than

15 mph below the set speed.● The brake pedal is depressed.● The clutch pedal is depressed for

a few seconds.● Selector lever is in N.● Engine speed is in a very low

range.● The Traction Control system (TC)

or Electronic Stability Control(ESC) is operating.


● Parking brake is applied.● Simultaneous pressing RES/+

and brake pedal deactivatescruise control and will deletestored speed.

Resume stored speedTurn thumb wheel to RES/+ at aspeed above 20 mph. The storedspeed will be resumed.

Switching offPress m: control indicator m ininstrument cluster extinguishes. Thestored speed is deleted.Pressing L for activating speedlimiter or switching off the ignition alsoswitches off cruise control anddeletes the stored speed.

Speed limiterThe speed limiter prevents thevehicle exceeding a preset maximumspeed.The maximum speed can be set at aspeed above 15 mph.

The driver can only accelerate up tothe preset speed. Deviations from thelimited speed may occur when drivingdownhill.The preset speed limit is displayed inthe Driver Information Centre whenthe system is active.

Activation

Press L, symbol L illuminates in theDriver Information Centre.If cruise control has been activatedbefore, it is switched off when speedlimiter is activated and the controlindicator m extinguishes.

Set speed limitAccelerate to the desired speed andbriefly turn thumb wheel to SET/-: thecurrent speed is stored as maximumspeed.On Midlevel display L and the speedlimit is displayed.

On Uplevel display L changes togreen.

Change speed limitWith speed limiter active, turn thumbwheel to RES/+ to increase or SET/-to decrease the desired maximumspeed.


Exceeding the speed limitWhen exceeding the limited speedwithout driver input, the speed willflash in the Driver Information Centreand a chime sounds during thisperiod.In the event of an emergency, it ispossible to exceed the speed limit bydepressing the accelerator pedalfirmly nearly to the final point. In thiscase no chime appears.Release the accelerator pedal andthe speed limiter function isreactivated once a speed lower thanthe limit speed is obtained.

DeactivationPress y: speed limiter is deactivatedand the vehicle can be driven withoutspeed limit.

On Midlevel display the stored limitedspeed is indicated in brackets.On Uplevel display L changes towhite.Additionally, a correspondingmessage appears.Speed limiter is deactivated, but notswitched off. Last stored speedremains in memory for later speedresume.

Resume limit speedTurn thumb wheel to RES/+. Thestored speed limit will be obtainedand is indicated without brackets inthe Driver Information Centre.

Switching offPress L, the speed limit indicationextinguishes in the Driver InformationCentre. The stored speed is deleted.By pressing m to activate cruisecontrol, speed limiter is alsodeactivated and the stored speed isdeleted.

By switching off the ignition, speedlimiter is also deactivated, but thespeed limit will be stored for nextspeed limiter activation.

Forward collision alertThe forward collision alert may help toavoid or reduce the harm caused byfront-end crashes.

A vehicle ahead is indicated by thecontrol indicator A.If a vehicle directly ahead isapproached too quickly, a warningchime is provided.


Additionally the driver gets notified bya flashing red LED stripe which isprojected on the windscreen in thedriver's field of view.A precondition is that forward collisionalert is not deactivated by pressingV on the steering wheel.

ActivationForward collision alert uses the frontcamera system in the windscreen todetect a vehicle directly ahead, inyour path, within a distance of approx.60 metres.Forward collision alert operatesautomatically above 25 mph, if it is notdeactivated by pressing V, seebelow.

Alerting the driverThe vehicle ahead control indicatorA illuminates green in the instrumentcluster when the system has detecteda vehicle in the driving path.

The control indicator A changes toyellow when the distance to apreceding moving vehicle gets toosmall or when approaching anothervehicle too rapidly.

Caution

The colour lighting of this controlindicator does not correspond tolocal traffic laws on followingdistance. The driver bears fullresponsibility for maintaining safefollowing distance according toapplicable traffic rules, weatherand road conditions etc. at alltimes.

When the time to a potential collisionwith a vehicle in front gets too smalland a collision is imminent, the drivergets notified by a flashing red LEDstripe which is projected on thewindscreen in the driver's field ofview.

Simultaneously a warning chimesounds. Depress the brake pedal andsteer the vehicle, if it is required by thesituation.

Selecting the alert sensitivityThe alert sensitivity can be set tonear, medium or far.


Press V; the current setting is shownin the Driver Information Centre.Press V again to change the alertsensitivity.

DectivationThe system can be deactivated.Press V repeatedly until ForwardCollision Alert Off appears in theDriver Information Centre.

General information

9 Warning

Forward collision alert is just awarning system and does notapply the brakes. Whenapproaching a vehicle ahead toorapidly, it may not provide youenough time to avoid a collision.The driver accepts fullresponsibility for the appropriatefollowing distance based on traffic,weather and visibility conditions.The complete attention of thedriver is always required whiledriving. The driver must always beready to take action and apply thebrakes.

System limitationsForward collision alert is designed towarn on vehicles only, but may reactalso to other objects.In the following cases, forwardcollision alert may not detect a vehicleahead or sensor performance islimited:● on winding roads● when weather limits visibility,

such as fog, rain, or snow● when the sensor is blocked by

snow, ice, slush, mud, dirt,windscreen damage or affectedby foreign items, e.g. stickers

Following distanceindicationThe following distance indicationdisplays the distance to a precedingmoving vehicle. The system uses thefront camera in the windscreen todetect the distance of a vehicledirectly ahead in your lane. It is activeat speeds above 25 mph.


When a preceding vehicle is detectedahead, the distance is indicated inseconds, displayed on a page in theDriver Information Centre 3 96. PressMENU on the turn signal lever toselect Vehicle InformationMenu ? and turn the adjusterwheel to choose following distanceindication page.

The minimum indicated distance is0.5 s.If there is no vehicle ahead or thevehicle ahead is out of range, twodashes will be displayed: -.- s.

Parking assist

The parking assist makes parkingeasier by measuring the distancebetween the vehicle and obstacles,and giving acoustic signals. It is thedriver, however, who bears fullresponsibility for the parkingmanoeuvre.The system consists of four ultrasonicparking sensors in the rear bumper. Ifthe vehicle is equipped with a frontparking assist the system consists offour additional ultrasonic parkingsensors in the front bumper.

Activation

When reverse gear is engaged, thesystem is activated automatically.The front parking assist can also beactivated at a low speed by pressingr.An illuminated LED in the parkingassist button indicates that thesystem is ready to operate.An obstacle is indicated by a buzzingsound. The interval between thesounds becomes shorter as thevehicle gets closer to the obstacle.When the distance is less than30 cm, the buzzing is continuous.


If r is pressed once within anignition cycle, the front parking assistis reactivated if the vehicle speedgoes below a certain value and if thevehicle speed has not exceeded16 mph beforehand.

DeactivationDeactivate the system by pressingr.The LED in the button will go out andPark Assist Off will be displayed in theDriver Information Centre.The system is deactivatedautomatically at a certain speed.

FaultIn the event of a fault in the system, avehicle message is displayed in theDriver Information Centre.Additionally, a vehicle message isdisplayed in the Driver InformationCentre if a malfunction of the systemdue to temporary conditions, e.g.snow covered sensors is detected.Vehicle messages 3 102.

Important hints for using theparking assist systems

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well asexternal noise sources may causethe system to fail to detectobstacles.Special attention has to be paid tolow obstacles which can damagethe lower part of the bumper. Ifsuch obstacles leave the detectionarea of the sensors duringapproach of the vehicle, acontinuous warning tone willsound.

Caution

Performance of the system can bereduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystem can be reduced due toheavy loading.

Special conditions apply if thereare taller vehicles in the vicinity(e.g. off-road vehicles, mini vans,vans). Object identification andcorrect distance indication in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross-section, e.g. objects ofnarrow size or soft materials, maynot be detected by the system.Parking assist systems do notdetect objects outside thedetection range.

NoticeThe parking assist systemautomatically detects factory-fittedtowing equipment. It is deactivatedwhen the connector is plugged in.The sensor may detect a non-existent object (echo disturbance)caused by external acoustic ormechanical disturbances.NoticeThe parking assist is deactivatedwhen the rear carrier system isextended.


Rear view cameraThe rear view camera assists thedriver when reversing by displaying aview of the area behind the vehicle.The view of the camera is displayedin the Info-Display.

9 Warning

The rear view camera does notreplace driver vision. Note thatobjects that are outside thecamera's field of view and theadvanced parking assist sensors,e.g. below the bumper orunderneath the vehicle, are notdisplayed.Do not reverse the vehicle by onlylooking at the Info-Display andcheck the surrounding areabehind and around the vehiclebefore reversing.

ActivationRear view camera is automaticallyactivated when reverse gear isengaged.

Functionality

The camera is mounted in the tailgatehandle and has a viewing angle of130°.

Due to the high position of thecamera, the rear bumper can be seenon the display as a guide to position.The area displayed by the camera islimited. The distance of the image thatappears on the display differs fromthe actual distance.

Guiding linesDynamic guiding lines are horizontallines at one metre intervals projectedon the picture to define the distanceto displayed objects.

Trajectory lane of the vehicle isshown in accordance with thesteering angle.


Warning symbolsWarning symbols are indicated astriangles 9 on the picture which showobstacles detected by the rearsensors of the advanced parkingassist.Additionally 9 appears on the top lineof the Info-Display with the warning tocheck the vehicle surrounding.

DeactivationThe camera is deactivated when acertain forward speed is exceeded orif reverse gear is not engaged forapprox. 10 seconds.Rear view camera can be manuallydeactivated in the vehiclepersonalisation menu in the Info-Display. Select the relevant setting inSettings .Vehicle personalisation 3 104.

Deactivation of guiding lines andwarning symbols

7'' Colour-Info-Display: Activation ordeactivation of the visual guiding linesand the warning symbols can bechanged via touch buttons in thelower zone of the display.8'' Colour-Info-Display: Activation ordeactivation of the visual guiding linesand the warning symbols can bechanged in the Settings menu in theInfo-Display.Info-Display 3 100.Vehicle personalisation 3 104.

FaultFault messages are displayed with a9 on the top line of the Info-Display.The rear view camera may notoperate properly when:● The surrounding is dark.● The sun or the beam of

headlights is shining directly intothe camera lens.

● Ice, snow, mud, or anything elsecovers the camera lens. Cleanthe lens, rinse it with water, andwipe it with a soft cloth.

● The vehicle is towing a trailer.● The vehicle had a rear end

accident.● There are extreme temperature

changes.

Traffic sign assistantFunctionalityThe traffic sign assistant systemdetects designated traffic signs via afront camera and displays them in theDriver Information Centre.


Traffic signs which will be detectedare:Limit and no passing signs● speed limit● no passing● end of speed limit● end of no passing

Road signsBeginning and end of:● city regions (country specific)● motorways● A-roads● play streets

Add-on signs● additional hints to traffic signs● restriction of trailer towing● tractor constraints● wet warning● ice warning● direction arrows

Speed limit signs are displayed in theDriver Information Centre until thenext speed limit sign or end of speedlimit is detected or up to a defined signtimeout.

Combinations of multiple signs in thedisplay are possible.

An exclamation mark in a frameindicates that there is an additionalsign detected which is not recognisedby the system.The system operates without loss ofperformance up to a speed of125 mph depending on the lightingconditions. At night the system isactive up to a speed of 100 mph.

Display indicationInformation about the currently validtraffic signs is available on thedesignated traffic sign assistant pagein the Driver Information Centre.

Additionally, the currently valid speedlimit is displayed permanently in thelower line of the Driver InformationCentre. In case a speed limit withaddon is available, a + symbol isdisplayed in this area.


Choose ? via MENU and selecttraffic sign assistant page with theadjuster wheel on the turn signal lever3 96.When another page on the DriverInformation Centre menu wasselected and then traffic signassistant page is chosen again, thelast recognised traffic sign will bedisplayed.

Alert functionThe alert function can be activated ordeactivated in the setting menu of thetraffic sign assistant page.

Once activated and when the trafficsign detection page is currently notdisplayed, newly detected speed limitand no passing signs are displayedas popup alerts in the DriverInformation Centre.

When traffic sign assistant page isdisplayed, press SET/CLR on the turnsignal lever.


Select Alerts ON or Alerts OFF byturning the adjuster wheel and pressSET/CLR.Pop-up alert is displayed for approx.eight seconds in the DriverInformation Centre.

System resetThe content of the traffic sign memorycan be cleared in the setting menu ofthe traffic sign assistant page byselecting Reset and confirm bypressing SET/CLR on the turn signallever.

Alternatively, SET/CLR can bepressed for three seconds to clear thecontent of the page.Upon successful reset, a chime willsound and the following “DefaultSign” is indicated until the next trafficsign is detected.

In some cases, traffic sign assistant iscleared up automatically by thesystem.

Clearing of traffic signsThere are different scenarios thatlead to clearing the currentlydisplayed traffic signs. After clearing,the “Default Sign” is displayed in theDriver Information Centre.

Reasons for signs being cleared:● A predefined distance was driven

or time has elapsed (differs foreach sign type)

● Vehicle drives through a turn● The speed becomes slower than

32 mph (city entry detection)

FaultThe traffic sign assistant system maynot operate correctly if:● The area of the windscreen,

where the front camera islocated, is not clean or affectedby foreign items, e.g. stickers.

● Traffic signs are completely orpartially covered or difficult todiscern.

● There are adverse environmentalconditions, e.g. heavy rain, snow,direct sunlight or shadows.

● Traffic signs are incorrectlymounted or damaged.

● Traffic signs do not comply withthe Vienna Convention on trafficsigns (Wiener Übereinkommenüber Straßenverkehrszeichen).


Caution

The system is intended to help thedriver within a defined speedrange to discern certain trafficsigns. Do not ignore traffic signswhich are not displayed by thesystem.The system does not discern anyother than the conventional trafficsigns that might give or end aspeed limit.Do not let this special featuretempt you into taking risks whendriving.Always adapt speed to the roadconditions.The driver assistance systems donot relieve the driver from fullresponsibility for vehicleoperation.

Lane departure warningThe lane departure warning systemobserves the lane markings betweenwhich the vehicle is driving via a frontcamera. The system detects lane

changes and warns the driver in theevent of an unintended lane changevia visual and acoustic signals.Criteria for the detection of anunintended lane change are:● no operation of turn signals● no brake pedal operation● no active accelerator operation or

speeding-up● no active steering

If the driver is active, no warning willbe issued.

Activation

The lane departure warning system isactivated by pressing ). Theilluminated LED in the buttonindicates that the system is switchedon.

When the control indicator ) in theinstrument cluster illuminates green,the system is ready to operate.The system is only operable atvehicle speeds above 35 mph and iflane markings are available.When the system recognises anunintended lane change, the controlindicator ) changes to yellow andflashes. Simultaneously a chimesound is activated.


DeactivationThe system is deactivated bypressing ), the LED in the buttonextinguishes.At speeds below 35 mph the systemis inoperable.

FaultThe lane departure warning systemmay not operate properly when:● the windscreen is not clean● there are adverse environmental

conditions like heavy rain, snow,direct sunlight or shadows

The system can not operate when nolane marking is detected.

FuelFuel for petrol enginesOnly use unleaded fuel that complieswith European standard EN 228 orE DIN 51626-1 or equivalent.The engine is capable of running withfuel that contains up to 10% ethanol(e.g. named E10).Use fuel with the recommendedoctane rating. A lower octane ratingcan reduce engine power and torqueand slightly increases fuelconsumption.

Caution

Do not use fuel or fuel additivesthat contain metallic compoundssuch as manganese-basedadditives. This may cause enginedamage.

Caution

Use of fuel that does not comply toEN 228 or E DIN 51626-1 orequivalent can lead to deposits orengine damage.

Caution

Use of fuel with a lower octanerating than the lowest possiblerating could lead to uncontrolledcombustion and engine damage.

The engine-specific requirementsregarding octane rating are given inthe engine data overview 3 224. Acountry-specific label at the fuel fillerflap can supersede the requirement.

Fuel for diesel enginesOnly use diesel fuel that complieswith EN 590.In countries outside the EuropeanUnion use Euro-Diesel fuel with asulphur concentration below 50 ppm.


Caution

Use of fuel that does not comply toEN 590 or similar can lead toengine powerloss, increased wearor engine damage.

Do not use marine diesel oils, heatingoils, Aquazole and similar diesel-water emulsions. Diesel fuels mustnot be diluted with fuels for petrolengines.

Fuel for liquid gas operationLiquid gas is known as LPG(Liquefied Petroleum Gas) or underits French name GPL (Gaz de PétroleLiquéfié). LPG is also known asAutogas.LPG consists mainly of propane andbutane. The octane rating is between105 and 115, depending on thebutane proportion. LPG is stored as aliquid at a pressure of approx. five toten bar.

The boiling point depends on thepressure and the mixing ratio. Atambient pressure, it is between-42 °C (pure propane) and -0.5 °C(pure butane).

Caution

The system works at an ambienttemperature of approx. -8 °C to100 °C.

Full functioning of the LPG systemcan only be guaranteed with liquidgas which complies with the minimumrequirements of DIN EN 589.

Fuel selector

Pressing LPG switches betweenpetrol and liquid gas operation assoon as the required parameters(coolant temperature, gastemperature and minimum enginespeed) have been reached. Therequirements are usually fulfilled afterapprox. 60 seconds (depending onexterior temperature) and the first firmpress on the accelerator. The statusLED shows the current operatingmode.LED off : petrol operationLEDflashes

: checking conditions forfuel transition to liquidgas operation.Illuminates if conditionsare fulfilled.

LED illu‐minates

: liquid gas operation

LEDflashesfivetimesandextin‐guishes

: liquid gas tank is emptyor failure in liquid gassystem. A message isdisplayed in the DriverInformation Centre.

If the fuel tank is empty, the enginewill not start.


The selected fuel mode is stored andreactivated at the next ignition cycle ifconditions allow.As soon as the liquid gas tanks areempty, petrol operation isautomatically engaged until theignition is switched off.When switching automaticallybetween petrol or gas operation, abrief delay of engine tractive powermay be noticeable.Every six months, run the petrol tankdown until control indicator Yilluminates, then refuel. This helpsmaintain fuel quality and systemfunction for petrol operation.Fill the tank completely at regularintervals to prevent corrosion in thetank.

Faults and remediesIf gas mode is not possible, check thefollowing:● Is there enough liquid gas

present?● Is there enough petrol present for

starting?

Due to extreme temperatures incombination with the gascomposition, it may take slightlylonger before the system switchesfrom petrol to gas mode.In extreme situations, the system mayalso switch back to petrol mode if theminimum requirements are notfulfilled. If conditions allow, it may bepossible to manually switch back toliquid gas operation.Seek the assistance of a workshop inthe event of all other faults.

Caution

Repairs and adjustments may onlybe made by trained specialists inorder to maintain the safety andwarranty on the LPG system.

Liquid gas is given a particular odour(odorised) so that any leaks can bedetected easily.

9 Warning

If you smell gas in the vehicle or inthe immediate vicinity, switch topetrol mode immediately. Nosmoking. No naked flames orignition sources.

If the gas odour persists, do not startthe engine. Have the cause of thefault remedied by a workshop.When using underground car parks,follow the instructions of the operatorand local laws.NoticeIn the event of an accident, switch offthe ignition and lights.


Refuelling

9 Danger

Before refuelling, switch offignition and any external heaterswith combustion chambers.Follow the operating and safetyinstructions of the filling stationwhen refuelling.

9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately by aworkshop.

Caution

In case of misfuelling, do notswitch on ignition.

Fuel filler flap is located at right rearside of vehicle.

The fuel filler flap can only be openedif the vehicle is unlocked. Push flapand open.


Turn the fuel filler cap slowlyanticlockwise to open.The fuel filler cap can be retained inthe bracket on the fuel filler flap.To refuel, fully insert the pump nozzleand switch it on.After automatic cut-off, the tank canbe topped up by operating the pumpnozzle a maximum of two more times.

Caution

Wipe off any overflowing fuelimmediately.

To close, turn the fuel filler capclockwise until it clicks.Close the flap and allow it to engage.

Liquid gas refuellingFollow the operating and safetyinstructions of the filling station whenrefuelling.The filling valve for the liquid gas isbehind the fuel filler cap.

Unscrew protective cap from the fillerneck.

Screw the required adapter hand-tight onto the filler neck.

ACME Adapter: Screw the nut of thefilling nozzle onto the adapter. Presslocking lever on filler nozzle down.DISH filler neck: Place the filler nozzleinto the adapter. Press locking leveron filler nozzle down.Bayonet filler neck: Place filler nozzleon the adapter and turn clockwise oranticlockwise through one quarterturn. Pull locking lever of filler nozzlefully.EURO filler neck: Press the fillernozzle onto the adapter until itengages.


Press the button at the liquid gassupply point. The filling system stopsor begins to run slowly when 80% ofthe tank volume is reached(maximum fill level).Release button on filling system andthe filling process stops. Release thelocking lever and remove the fillernozzle. A small quantity of liquid gasmay escape.Remove adapter and stow in vehicle.Fit protective cap to prevent thepenetration of foreign bodies into thefiller opening and the system.

9 Warning

Due to the system design, anescape of liquid gas afterreleasing the locking lever isunavoidable. Avoid inhaling.

9 Warning

The liquid gas tank should only befilled to 80% capacity, for safetyreasons.

The multivalve on the liquid gas tankautomatically limits the fill quantity. Ifa larger quantity is added, werecommend not exposing the vehicleto the sun until the excess amounthas been used up.

Filling adapterAs filling systems are notstandardised, different adapters arerequired which are available fromVauxhall Distributors and fromVauxhall Authorised Repairers.

ACME adapter: Belgium, Germany,Ireland, Luxembourg, Switzerland

Bayonet adapter: Netherlands,Norway, Spain, United Kingdom

EURO adapter: Spain


DISH adapter: Austria, Bosnia-Herzegovina, Bulgaria, CzechRepublic, Croatia, Denmark, Estonia,France, Greece, Hungary, Italy,Latvia, Lithuania, Macedonia,Poland, Portugal, Romania, Serbia,Slovakia, Slovenia, Sweden,Switzerland, Turkey, Ukraine

Fuel filler capOnly use genuine fuel filler caps.Diesel-engined vehicles have specialfuel filler caps.

Fuel consumption - CO2-Emissions The values for fuel consumption(combined) of the model VauxhallMokka is within a range of 36 to72 mpg.The values for CO2 emission(combined) is within a range of 155 to103 g/km.For the values specific to yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

General informationThe official fuel consumption andspecific CO2 emission figures quotedrelate to the EU base model withstandard equipment.Fuel consumption data and CO2emission data are determinedaccording to regulationR (EC) No. 715/2007 (in the latestapplicable version), taking into

consideration the vehicle weight inrunning order, as specified by theregulation.The figures are provided only for thepurpose of comparison betweendifferent vehicle variants and mustnot be taken as a guarantee for theactual fuel consumption of aparticular vehicle. Additionalequipment may result in slightlyhigher results than the statedconsumption and CO2 figures.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.


Trailer hitchGeneral informationOnly use towing equipment that hasbeen approved for your vehicle.Entrust retrofitting of towingequipment to a workshop. It may benecessary to make changes thataffect the cooling system, heatshields or other equipment.The bulb outage detection function fortrailer brake light cannot detect apartial bulb outage, e.g. in case of fourtimes five watt bulbs, the function onlydetects lamp outage when only asingle five Watt lamp remains or noneremain.Fitting of towing equipment couldcover the opening of the towing eye.If this is the case, use the coupling ballbar for towing. Always keep thecoupling ball bar in the vehicle whennot in use.

Driving characteristics andtowing tipsBefore attaching a trailer, lubricatethe coupling ball. However, do not doso if a stabiliser, which acts on thecoupling ball, is being used to reducesnaking movements.For trailers with low driving stabilityand caravan trailers with a permittedgross vehicle weight of more than1000 kg a speed of 50 mph must notbe exceeded; the use of a stabiliser isrecommended.If the trailer starts snaking, drive moreslowly, do not attempt to correct thesteering and brake sharply ifnecessary.When driving downhill, drive in thesame gear as if driving uphill anddrive at a similar speed.Adjust tyre pressure to the valuespecified for full load 3 230.

Trailer towingTrailer loadsThe permissible trailer loads arevehicle and engine-dependentmaximum values which must not beexceeded. The actual trailer load isthe difference between the actualgross weight of the trailer and theactual coupling socket load with thetrailer coupled.The permissible trailer loads arespecified in the vehicle documents. Ingeneral, they are valid for gradientsup to max. 12%.The permitted trailer loads apply up tothe specified incline and up to analtitude of 1000 metres above sealevel. Since engine power decreasesas altitude increases due to the airbecoming thinner, therefore reducingclimbing ability, the permissible grosstrain weight also decreases by 10%for every 1000 metres of additionalaltitude. The gross train weight doesnot have to be reduced when drivingon roads with slight inclines (less than8%, e.g. motorways).


The permissible gross train weightmust not be exceeded. This weight isspecified on the identification plate3 219.

Vertical coupling loadThe vertical coupling load is the loadexerted by the trailer on the couplingball. It can be varied by changing theweight distribution when loading thetrailer.The maximum permissible verticalcoupling load (75 kg) is specified onthe towing equipment identificationplate and in the vehicle documents.Always aim for the maximum load,especially in the case of heavytrailers. The vertical coupling loadshould never fall below 25 kg.

Rear axle loadThe permissible axle loads (seeidentification plate or vehicledocuments) must not be exceeded.

Towing equipment

Caution

When operating without a trailer,remove the coupling ball bar.

Stowage of coupling ball bar

The bag with the coupling ball bar isstowed in the rear stowagecompartment on the floor.Place the strap through the lashingeye, wrap around twice and tightenthe strap to secure the bag.

Fitting the coupling ball bar

Disengage and fold down the socket.Remove the sealing plug from theopening for the coupling ball bar andstow it.


Checking the tensioning of thecoupling ball bar

● Red marking on rotary knob mustpoint towards green marking oncoupling ball bar.

● The gap between the rotary knoband the coupling ball bar must beapprox. 6 mm.

● The key must be in position c.Otherwise, the coupling ball bar mustbe tensioned before being inserted:● Unlock coupling ball bar by

turning key to position c.

● Pull out rotary knob and turnclockwise as far as it will go.

Inserting the coupling ball bar

Insert the tensioned coupling ball barin the opening and push firmlyupwards until it audibly engages.The rotary handle snaps back into itsoriginal position resting against thecoupling ball bar without a gap.

9 Warning

Do not touch rotary handle duringinsertion.

Lock the coupling ball bar by turningthe key to position e. Remove the keyand close the protective flap.

Eye for break-away stopping cable


Attach breakaway stopping cable toeye.

Check that the coupling ball bar iscorrectly installed● Green marking on rotary knob

must point towards greenmarking on coupling ball bar.

● There must be no gap betweenthe rotary handle and thecoupling ball bar.

● The coupling ball bar must befirmly engaged in the opening.

● The coupling ball bar must belocked and the key removed.

9 Warning

Towing a trailer is permitted onlywhen a coupling ball bar is fittedcorrectly. If the coupling ball bardoes not engage correctly, seekthe assistance of a workshop.

Dismounting the coupling ball bar

Open the protective flap and turn thekey to position c to unlock thecoupling ball bar.Pull out rotary handle and turnclockwise as far as it will go. Pull outcoupling ball bar downwards.Insert sealing plug in opening. Foldaway socket.

176 Vehicle care

Vehicle care

General Information ................... 176Accessories and vehiclemodifications .......................... 176

Vehicle storage ........................ 177End-of-life vehicle recovery ..... 177

Vehicle checks ........................... 178Performing work ...................... 178Bonnet ..................................... 178Engine oil ................................. 179Engine coolant ......................... 180Power steering fluid ................. 180Washer fluid ............................ 181Brakes ..................................... 181Brake fluid ............................... 181Vehicle battery ......................... 182Diesel fuel system bleeding ..... 183Wiper blade replacement ........ 184

Bulb replacement ....................... 185Halogen headlights .................. 185Fog lights ................................. 186Tail lights ................................. 187Number plate light ................... 188

Electrical system ........................ 189Fuses ....................................... 189Engine compartment fuse box . 189

Instrument panel fuse box ....... 191Load compartment fuse box .... 193

Vehicle tools .............................. 194Tools ........................................ 194

Wheels and tyres ....................... 195Winter tyres ............................. 195Tyre designations .................... 195Tyre pressure .......................... 195Tyre pressure monitoringsystem .................................... 196

Tread depth ............................. 200Changing tyre and wheel size . 201Wheel covers ........................... 201Tyre chains .............................. 201Tyre repair kit .......................... 202Wheel changing ....................... 205Spare wheel ............................ 207

Jump starting ............................. 209Towing ....................................... 211

Towing the vehicle ................... 211Towing another vehicle ........... 212

Appearance care ....................... 213Exterior care ............................ 213Interior care ............................. 215

General InformationAccessories and vehiclemodificationsWe recommend the use of genuineparts and accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Any modification, conversion or otherchanges made to standard vehiclespecifications (including, withoutlimitation, software modifications,modifications of the electronic controlunits) may invalidate the warrantyoffered by Vauxhall. Furthermore,such changes may impact fuelconsumption, CO2 emissions andother emissions of the vehicle andcause the vehicle to no longerconform to the type approval,impacting the validity of your vehicleregistration.

Vehicle care 177

Caution

When transporting the vehicle ona train or on a recovery vehicle, themud flaps might be damaged.

Vehicle storageStorage for a long period of timeIf the vehicle is to be stored for severalmonths:● Wash and wax the vehicle.● Have the wax in the engine

compartment and underbodychecked.

● Clean and preserve the rubberseals.

● Fill up fuel tank completely.● Change the engine oil.● Drain the washer fluid reservoir.● Check the coolant antifreeze and

corrosion protection.● Adjust tyre pressure to the value

specified for full load.

● Park the vehicle in a dry, wellventilated place. Engage first orreverse gear or set selector leverto P. Prevent the vehicle fromrolling.

● Do not apply the parking brake.● Open the bonnet, close all doors

and lock the vehicle.● Disconnect the clamp from the

negative terminal of the vehiclebattery. Beware that all systemsare not functional, e.g. anti-theftalarm system.

Putting back into operationWhen the vehicle is to be put back intooperation:● Connect the clamp to the

negative terminal of the vehiclebattery. Activate the electronicsof the power windows.

● Check tyre pressure.● Fill up the washer fluid reservoir.● Check the engine oil level.● Check the coolant level.● Fit the number plate if necessary.

End-of-life vehicle recoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on ourwebsite, where legally required. Onlyentrust this work to an authorisedrecycling centre.Gas vehicles must be recycled by aservice centre authorised for gasvehicles.

178 Vehicle care

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

9 Danger

The ignition system and Xenonheadlights use extremely highvoltage. Do not touch.

BonnetOpening

Pull the release lever and return it toits original position.

Move the safety catch sideways to theleft vehicle side and open the bonnet.

Vehicle care 179

Pull up the support rod lightly from theholder. And then secure it at the leftside hook on the bonnet.If the bonnet is opened during anAutostop, the engine will be restartedautomatically for safety reasons.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and allow it to fallinto the latch from a low height(20-25 cm). Check that the bonnet isengaged.

Caution

Do not press the bonnet into thelatch, to avoid dents.

Engine oilCheck the engine oil level manuallyon a regular basis to prevent damageto the engine. Ensure that the correctspecification of oil is used.Recommended fluids and lubricants3 217.

The maximum engine oilconsumption is 0.6 l per 1000 km.Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least five minutes.Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.Insert dipstick to the stop on thehandle and make half a turn.

When the engine oil level hasdropped to the MIN mark, top upengine oil.

We recommend the use of the samegrade of engine oil that was used atlast change.The engine oil level must not exceedthe MAX mark on the dipstick.

180 Vehicle care

The engine oil filler cap is located onthe camshaft cover.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 229.Fit the cap on straight and tighten it.

Engine coolantThe coolant provides freezeprotection down to approx. -30 °C. Innorthern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -40 °C.

Caution

Only use approved antifreeze.

Coolant and antifreeze 3 217.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above thefilling line mark. Top up if the level islow.

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

To top up use a 1:1 mixture ofreleased coolant concentrate mixedwith clean tap water. If no coolantconcentrate is available, use cleantap water. Install the cap tightly. Havethe coolant concentration checkedand have the cause of the coolantloss remedied by a workshop.

Power steering fluid

Caution

Extremely small amounts ofcontamination can cause steeringsystem damage and cause it to notwork properly. Do not allowcontaminates to contact the fluidside of the reservoir cap/dipstick orfrom entering the reservoir.

Vehicle care 181

Power steering fluid level normallydoes not need to be checked. If anunusual noise sounds during steeringor the power steering reactsconspicuously, seek the assistance ofa workshop.

Washer fluid

Fill with clean water mixed with asuitable quantity of approvedwindscreen washer fluid whichcontains antifreeze.

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

Washer fluid 3 217.

BrakesIn the event of minimum thickness ofthe brake lining, a squealing noisesounds during braking.Continued driving is possible buthave the brake lining replaced assoon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

182 Vehicle care

The brake fluid level must be betweenthe MIN and the MAX marks.If fluid level is below MIN seek theassistance of a workshop.Brake and clutch fluid 3 217.

Vehicle batteryThe vehicle battery is maintenance-free provided that the driving profileallows sufficient charging of thebattery. Short-distance-driving andfrequent engine starts can dischargethe battery. Avoid the use ofunnecessary electrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.Laying up the vehicle for more thanfour weeks can lead to batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.The anti-theft alarm siren must bedeactivated as follows: Switch theignition on then off, disconnect thevehicle's battery within 15 seconds.Vehicle battery discharge protection3 124.

Replacing the vehicle batteryNoticeAny deviation from the instructionsgiven in this section may lead totemporary deactivation of the stop-start system.

When the vehicle battery is beingreplaced, please ensure that thereare no open ventilation holes in thevicinity of the positive terminal. If aventilation hole is open in this area, itmust be closed off with a dummy cap,and the ventilation in the vicinity of thenegative terminal must be opened.Only use vehicle batteries that allowthe fuse box to be mounted above thevehicle battery.In vehicles with an AGM (AbsorptiveGlass Mat) battery, make sure tohave the battery replaced withanother AGM battery.

Vehicle care 183

An AGM battery can be identified bythe label on the battery. Werecommend the use of an originalVauxhall vehicle battery.NoticeUsing an AGM vehicle batterydifferent from the original Vauxhallvehicle battery may result in a lowerperformance.

We recommend that you have thevehicle battery replaced by aworkshop.Stop-start system 3 137.

Charging the vehicle battery

9 Warning

On vehicles with stop-startsystem, ensure that the chargingpotential does not exceed14.6 volts when using a batterycharger. Otherwise the vehiclebattery might be damaged.

Jump starting 3 209.

Warning label

Meaning of symbols:● No sparks, naked flames or

smoking.● Always shield eyes. Explosive

gases can cause blindness orinjury.

● Keep the vehicle battery out ofreach of children.

● The vehicle battery containssulphuric acid which could causeblindness or serious burninjuries.

● See the Owner's Manual forfurther information.

● Explosive gas may be present inthe vicinity of the vehicle battery.

Diesel fuel system bleedingIf the tank has been run dry, the dieselfuel system must be bled. Switch onthe ignition three times for15 seconds at a time. Then crank theengine for a maximum of40 seconds. Repeat this process afterno less than 5 seconds. If the enginefails to start, seek the assistance of aworkshop.

184 Vehicle care

Wiper blade replacement

Lift the wiper arm, press button todisengage the wiper blade andremove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Wiper blade on the rear window

1. Remove the wiper cover from thewiper assembly.

2. Lift wiper blade.

3. Press slider holder pin.4. Pull wiper blade out.

Vehicle care 185

Bulb replacementSwitch off the ignition and turn off therelevant switch or close the doors.Only hold a new bulb at the base. Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.Replace headlight bulbs from withinthe engine compartment.NoticeAfter driving in heavy rain or afterwashing, some exterior light lensescould appear frosty.This condition is caused by thetemperature difference between theinside and outside of the light.This is similar to the condensationon your windows inside your vehicleduring the rain and doesn't indicatea problem with your vehicle.If the water leaks into the light bulbcircuitry, have the vehicle checkedby your authorised workshop.

Halogen bulbs

9 Warning

Halogen bulbs have pressurizedgas inside and can burst if youdrop or scratch the bulb. You orothers could be injured. Be sure toread and follow the instructions onthe bulb package.

LED lightingThis vehicle has several LED lights.For replacement of any LED lightingassembly, contact a workshop.

Halogen headlightsBaselevel headlight assemblyThe base model vehicle has halogenhigh beam and low beam headlights,an LED turn and lane-change signal,a sidelight and daytime running lightson the headlight assembly.

Passenger side shown, driver sidesimilar.On the driver side remove thewindscreen washer bottle filler neck,before changing a bulb.1. High beam headlights2. Low beam headlights

High beam and low beam headlights1. Open the bonnet. Bonnet 3 178

186 Vehicle care

2. Remove the protective cover.3. Turn the bulb anticlockwise and

pull straight back.

4. Disconnect the wiring harnessconnector from the bulb.

5. Install the new bulb in theheadlight assembly by turningclockwise.

6. Reconnect the wiring harnessconnector.

7. Install the protective cover.For the driver side, reinstall thewindscreen washer bottle filler neckby firmly pushing it straight into thebottle. Ensure that the filler neck clipengages into the underhood electricalcentre retainer.

Uplevel headlight assemblyThe uplevel model vehicle has LEDhigh beam and low beam headlights,a turn and lane-change signal, asidelight and daytime running lightson the headlight assembly.

Fog lightsThe bulbs are accessible from theunderside of the vehicle

1. Turn the respective wheel insideto get better access and removethree torx screws on outside ofwheel house. Vehicle tools3 194.

2. Pull and hold lining to get accessto the bulb holder.

Vehicle care 187

3. Pull the retaining rib outwards andremove plug connector from thebulb socket.

4. Turn the bulb holder anticlockwiseand remove it from the reflector.

5. Remove and replace the bulbsocket with bulb and attach theplug connector.

6. Insert the bulb socket into thereflector by turning clockwise andengage.

7. Re-assemble the lining and fastenthe three torx screws.

Tail lightsThe vehicle has halogen turn andlane-change signals, a back-up lightand LED tail/stop lights on the tail lightassembly.

Left-hand side

1. Disengage both covers at therespective outer side by insertinga screwdriver. Remove bothcovers and unscrew screws.Remove the panel.

2. First disengage cover by insertinga screwdriver at the recess. Thendisengage cover at the front andupper side. Remove cover.

188 Vehicle care

Right-hand side

1. Remove the storage door and thetyre repair kit.

2. Remove the cover.

3. Turn and lane-change signal light(1)Back-up light (2)

4. Remove bulb holder. Removeand renew bulb.

5. Insert bulb holder into the tail lightassembly. Install tail lightassembly in body and tighten.Close covers and engage.

6. Switch on ignition, operate andcheck all lights.

Number plate light

1. Prise the light out with ascrewdriver.

2. Remove bulb housingdownwards, taking care not to pullon the cable.Rotate bulb holder anticlockwiseto disengage.

Vehicle care 189

3. Remove bulb from holder andrenew bulb.

4. Insert bulb holder in bulb housingand rotate clockwise.

5. Insert bulb housing and secureusing a screwdriver.

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.In a box above the positive terminal ofthe battery are some main fuses. Ifnecessary have them changed by aworkshop.Before replacing a fuse, turn off therespective switch and the ignition.A blown fuse can be recognised by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.NoticeNot all fuse box descriptions in thismanual may apply to your vehicle.When inspecting the fuse box, referto the fuse box label.

Fuse extractorA fuse extractor may be located in thefuse box in the engine compartment.Place the fuse extractor on thevarious types of use from the top orside, and withdraw fuse.

Engine compartment fusebox

The fuse box is in the enginecompartment.Disengage the cover, lift it upwardsand remove.

190 Vehicle care

Mini Fuses

No. Circuit

1 Sunroof

2 Exterior mirror switch/Rainsensor

3 –

4 –

5 Electrical brake control module

6 Intelligent battery sensor

7 Steering column lock

8 Transmission control module

9 –

10 Rear view camera/Interior rearview mirror/Headlight switch/Headlight

11 Rear window wiper

12 Heated rear window

13 Seat, lumbar support

14 Heated exterior mirrors

15 LPG module/Fuel systemcontrol module

No. Circuit

16 Seat heating

17 Transmission control module R/C/Water pump/Auxiliary heater

18 Engine control module R/C

19 Fuel pump

20 –

21 Cooling fan

22 –

23 Ignition coil/Injectors

24 Washer pump

25 Headlamp actuator (right hand)

26 Engine control sensors

27 –

28 Ignition

29 Ignition 1/2

30 Exhaust system

31 Left-hand high beam

32 Right-hand high beam

Vehicle care 191

No. Circuit

33 Engine control module

34 Horn

35 Air conditioning system

36 Front fog lamp

J-cases Fuses

No. Circuit

1 Electrical brake control module

2 Front wiper

3 Power module

4 Power terminal of instrumentpanel fuse box

5 –

6 Fuel heater

7 Starter

8 Cooling fan

9 Cooling fan

No. Circuit

10 Engine control module/Glowplug

11 Starter

Instrument panel fuse box

Interior fuse block is located on theunderside of the driver's sideinstrument panel.To access the fuses, remove thestorage.To remove the storage, open and pullit.

Mini Fuses

192 Vehicle care

No. Circuit

1 Body control module








9 Ignition switch

10 Safety diagnosis module

11 Data link connector

12 Climate control

13 Tailgate

14 Central gateway module

15 Lane departure warning/Interiormirror

16 Adaptive forward lighting

17 Column lock

No. Circuit

18 Ultrasonic park assist module

19 Body control module/Regulatedvoltage control

20 Steering wheel

21 –

22 Cigarette lighter/DC accessorypower outlet (front)

23 Cigarette lighter/DC accessorypower outlet (rear centerconsole)

24 Spare

25 Telematics service module

26 Heated steering wheel

27 Instrument panel cluster/Info‐tainment system/Auxiliaryheater switch

28 Trailer socket

29 Display/Infotainment system

30 Transmission control module

No. Circuit

31 Instrument panel cluster

32 Infotainment system

33 Trailer socket

34 Passive entry/Passive startmodule

S/B Fuses

No. Circuit

01 Power seat switch

02 Spare

03 Power windows front

04 Power windows rear

05 Logistic mode

06 Power seat switch

07 Spare

08 Spare

Vehicle care 193

Load compartment fuse box

Located in the left side of rearcompartment.To access the fuses, remove thecover.

Mini Fuses

No. Circuit

1 –

2 –

3 Amplifier

4 –

5 All-wheel drive

6 Spare

7 –

8 Spare

9 Spare

10 Spare

11 –

12 Spare

13 –

14 –

15 Spare

16 –

194 Vehicle care

No. Circuit

17 –

18 –

S/B Fuses

No. Circuit

1 –

2 –

3 –

4 –

5 –

6 –

7 DC/DC 400W transformer

8 DC/DC 400W transformer

9 –

Vehicle toolsToolsVehicles with tyre repair kit

The tools and tyre repair kit are in theright side of the load compartment.3 202.

Vehicles with spare wheel

The jack and the tools are in a storagecompartment in the loadcompartment above the spare wheel.Wheel changing 3 205, spare wheel3 207.

Vehicle care 195

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance of aworkshop in the event of damage orunusual wear.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.All tyre sizes are permitted as wintertyres 3 230.In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Tyre designationsE.g. 215/60 R 16 95 H215 : tyre width, mm60 : cross-section ratio (tyre height

to tyre width), percentageR : belt type: RadialRF : type: RunFlat16 : wheel diameter, inches95 : load index e.g. 95 is equivalent

to 690 kgH : speed code letter

Speed code letter:Q : up to 100 mphS : up to 112 mphT : up to 118 mphH : up to 130 mphV : up to 150 mphW : up to 168 mph

Choose a tyre appropriate for themaximum speed of your vehicle.The maximum speed is achievable atkerb weight with driver (75 kg) plus125 kg payload. Optional equipmentcould reduce the maximum speed ofthe vehicle.Performance 3 226.

Directional tyresFit directional tyres such that they rollin the direction of travel. The rollingdirection is indicated by a symbol(e.g. an arrow) on the sidewall.

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey. Do not forget the sparewheel. This also applies to vehicleswith tyre pressure monitoring system.Unscrew the valve cap.

Tyre pressure 3 230.

196 Vehicle care

The tyre pressure information labelon the left or right door frameindicates the original equipment tyresand the correspondent tyrepressures.The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.Always inflate the spare tyre to thepressure specified for full load.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.Tyre pressures differ depending onvarious options. For the correct tyrepressure value, follow the procedurebelow:1. Identify the engine identifier code.

Engine data 3 224.2. Identify the respective tyre.

The tyre pressure tables show allpossible tyre combinations 3 230.

For the tyres approved for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.The driver is responsible for correctadjustment of tyre pressure.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

9 Warning

For specific tyres therecommended tyre pressure asshown in the tyre pressure tablemay exceed the maximum tyrepressure as indicated on the tyre.Never exceed the maximum tyrepressure as indicated on the tyre.

Temperature dependencyThe tyre pressure depends on thetemperature of the tyre. Duringdriving, tyre temperature andpressure increase. Tyre pressurevalues provided on the tyreinformation label and tyre pressurechart are valid for cold tyres, whichmeans at 20 °C.The pressure increases by nearly1.5 psi for a 10 °C temperatureincrease. This must be consideredwhen warm tyres are checked.The tyre pressure value displayed inthe Driver Information Centre showsthe real tyre pressure. A cooled downtyre will show a decreased value,which does not indicate an air leak.

Tyre pressure monitoringsystemThe tyre pressure monitoring systemchecks the pressure of all four tyresonce a minute when vehicle speedexceeds a certain limit.

Vehicle care 197

Caution

Tyre pressure monitoring systemwarns only about low tyre pressurecondition and does not replaceregular tyre maintenance by thedriver.

All wheels must be equipped withpressure sensors and the tyres musthave the prescribed pressure.NoticeIn countries where the tyre pressuremonitoring system is legallyrequired, the use of wheels withoutpressure sensors will invalidate thevehicle type approval.

The current tyre pressures can beshown in the Driver InformationCentre.Midlevel display:

Select the Tyre pressure page underthe Vehicle Information Menu ? inthe Driver Information Centre 3 96.Uplevel display:

Select the Tyre pressure page underthe Info Menu in the DriverInformation Centre 3 96.System status and pressure warningsare displayed by a messageindicating the corresponding tyre inthe Driver Information Centre.The system considers the tyretemperature for the warnings.Temperature dependency 3 195.

A detected low tyre pressurecondition is indicated by the controlindicator w 3 94.If w illuminates, stop as soon aspossible and inflate the tyres asrecommended 3 230.If w flashes for 60-90 seconds andthen illuminates continuously, there isa fault in the system. Consult aworkshop.

198 Vehicle care

After inflating, some driving may berequired to update the tyre pressurevalues in the Driver InformationCentre. During this time w mayilluminate.If w illuminates at lower temperaturesand extinguishes after driving, thiscould be an indicator for approachinga low tyre pressure condition. Checktyre pressure.Vehicle messages 3 102.If the tyre pressure must be reducedor increased, switch off ignition.Only mount wheels with pressuresensors, otherwise the tyre pressurewill not be displayed and willuminates continuously.A spare wheel or temporary sparewheel is not equipped with pressuresensors. The tyre pressuremonitoring system is not operationalfor these tyres. Control indicator willuminates. For the further threetyres, the system remainsoperational.

The use of commercially-availableliquid tyre repair kits can impair thefunction of the system. Factory-approved repair kits can be used.Operating electronic devices or beingclose to facilities using similar wavefrequencies could disrupt the tyrepressure monitoring system.Each time the tyres are replaced, tyrepressure monitoring system sensorsmust be dismounted and serviced.For the screwed sensor, replacevalve core and sealing ring. For theclipped sensor, replace completevalve stem.

Vehicle loading statusAdjust tyre pressure to load conditionaccording to tyre information label ortyre pressure chart 3 230, and selectthe appropriate setting in themenuTyre Load in the DriverInformation Centre,VehicleInformation Menu 3 96. This setting isthe reference for the tyre pressurewarnings.

The Tyre load menu only appearswhen the vehicle is at a standstill andthe parking brake is applied. Onvehicles with automatic transmissionthe selector lever must be in P.Midlevel display:

Select the Tyre load page under theVehicle Information Menu ? in theDriver Information Centre 3 96.● Light for comfort pressure up to

three people.● Eco for Eco pressure up to three

people.● Max for full loading.

Uplevel display:

Vehicle care 199

Select the Tyre load page under theOptions Menu in the DriverInformation Centre 3 96.● Light for comfort pressure up to

three people.● Eco for Eco pressure up to three

people.● Max for full loading.

Tyre pressure sensor matchingprocessEach tyre pressure sensor has aunique identification code. Theidentification code must be matchedto a new wheel position after rotatingthe wheels or exchanging the

complete wheel set and if one or moretyre pressure sensors were replaced.The tyre pressure sensor matchingprocess should also be performedafter replacing a spare wheel with aroad wheel containing a tyre pressuresensor.The malfunction light w and thewarning message should extinguishat the next ignition cycle. The sensorsare matched to the wheel positions,using a relearn tool, in the followingorder: left side front wheel, right sidefront wheel, right side rear wheel andleft side rear wheel. The turn signallight at the current active position isilluminated until sensor is matched.Consult a workshop for service. Thereare two minutes to match the firstwheel position, and five minutesoverall to match all four wheelpositions. If it takes longer, thematching process stops and must berestarted.The tyre pressure sensor matchingprocess is:1. Apply the parking brake.2. Turn the ignition on.

3. On vehicles with automatictransmission: set the selectorlever to P.On vehicles with manualtransmission: select neutral.

4. Press MENU on the turn signallever to select the VehicleInformation Menu in the DriverInformation Centre.

5. Turn the adjuster wheel to scroll tothe tyre pressure menu.Midlevel display:

Uplevel display:

200 Vehicle care

6. Press SET/CLR to begin thesensor matching process. Amessage requesting acceptanceof the process should bedisplayed.

7. Press SET/CLR again to confirmthe selection. The horn soundstwice to signal that the receiver isin relearn mode.

8. Start with the left side front wheel.9. Place the relearn tool against the

tyre sidewall, near the valve stem.Then press the button to activatethe tyre pressure sensor. A hornchirp confirms that the sensor

identification code has beenmatched to this tyre and wheelposition.

10. Proceed to the right side frontwheel, and repeat the procedurein Step 9.

11. Proceed to the right side rearwheel, and repeat the procedurein Step 9.

12. Proceed to the left side rearwheel, and repeat the procedurein Step 9. The horn sounds twiceto indicate the sensoridentification code has beenmatched to the left side rearwheel, and the tyre pressuresensor matching process is nolonger active.

13. Turn off the ignition.14. Set all four tyres to the

recommended air pressure levelas indicated on the tyre pressureinformation label.

15. Ensure the tyre loading status isset according to the selected tyrepressure 3 96.

Tread depthCheck tread depth at regularintervals.Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).For safety reasons it is recommendedthat the tread depth of the tyres onone axle should not vary by more than2 mm.

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wear

Vehicle care 201

indicators (TWI). Their position isindicated by markings on thesidewall.If there is more wear at the front thanthe rear, swap round front wheels andrear wheels. Ensure that the directionof rotation of the wheels is the sameas before.Tyres age, even if they are not used.We recommend tyre replacementevery six years.

Changing tyre and wheelsizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme thespeedometer as well as the nominaltyre pressure and make other vehiclemodifications.After converting to a different tyresize, have the label with tyrepressures replaced.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory-approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.If the wheel covers and tyres used arenot factory-approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

Vehicles with alloy wheels: Whenmounting steel wheels with alloywheel nuts, e.g. when changing towinter tyres, the wheel covers cannotbe attached to the steel wheels.

Tyre chains

Use tyre chains only on front wheels.

9 Warning

Damage may lead to tyre blowout.

Tyre chains are permitted on tyres ofsize 215/65 R16, 215/60 R17 and215/55 R18.

202 Vehicle care

On tyres of size 215/65 R16 and215/60 R17 always use fine meshchains suitable for sport utilityvehicles that add no more than9 mm to the tyre tread and the inboardsides (including chain lock).On tyres of size 215/55 R18 only usespecial snow chains which arepermitted for Vauxhall Mokka andtyres of these sizes. For furtherinformation contact a workshop.The use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at tyre's sidewall cannot be repairedwith the tyre repair kit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:Apply the parking brake and engagefirst gear, reverse gear or P.

The tyre repair kit is located in theright side of rear compartment.

1. Take the tyre repair kit from thecompartment.

2. Remove the compressor.

Vehicle care 203

3. Remove the electrical connectioncable (1) and air hose (2) from thestowage compartments on theunderside of the compressor.

4. Screw the compressor air hose tothe connection on the sealantbottle.

5. Fit the sealant bottle into theretainer on the compressor.Set the compressor near the tyrein such a way that the sealantbottle is upright.

6. Unscrew valve cap from defectivetyre.

7. Screw the filler hose to the tyrevalve.

8. The switch on the compressormust be set to J.

9. Connect the compressor plug tothe power outlet or cigarettelighter socket.To avoid discharging the battery,we recommend running theengine.

10. Set the rocker switch on thecompressor to I. The tyre is filledwith sealant.

11. The compressor pressure gaugebriefly indicates up to 6 bar whilstthe sealant bottle is emptying(approx. 30 seconds). Then thepressure starts to drop.

12. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

13. The prescribed tyre pressureshould be obtained withinten minutes. Tyre pressure3 230. When the correct pressureis obtained, switch off thecompressor.

204 Vehicle care

If the prescribed tyre pressure isnot obtained within ten minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure for10 minutes. If the prescribed tyrepressure is still not obtained, thetyre is too badly damaged. Seekthe assistance of a workshop.Drain excess tyre pressure withthe button over the pressureindicator.Do not run the compressor longerthan 10 minutes.

14. Detach the tyre repair kit. Pushcatch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

15. Remove any excess sealantusing a cloth.

16. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

17. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.6 miles (but no more thanten minutes), stop and check tyrepressure. Screw compressor airhose directly onto tyre valve andcompressor when doing this.

If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

18. Stow away tyre repair kit in loadcompartment.

Vehicle care 205

NoticeThe driving characteristics of therepaired tyre are severely affected,therefore have this tyre replaced.If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens at apressure of 102 psi.Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

Wheel changingSome vehicles are equipped with atyre repair kit instead of a spare wheel3 202.Make the following preparations andobserve the following information:● Park the vehicle on a level, firm

and non-skid surface. The frontwheels must be in the straight-ahead position.

● Apply the parking brake andengage first gear, reverse gear orP.

● Remove the spare wheel 3 207.● Never change more than one

wheel at a time.● Use the jack only to change

wheels in case of puncture, notfor seasonal winter or summertyre change.

● The jack is maintenance-free.● If the ground on which the vehicle

is standing is soft, a solid board(max. 1 cm thick) should beplaced under the jack.

● Take heavy objects out of thevehicle before jacking up.

● No people or animals may be inthe vehicle when it is jacked-up.

● Never crawl under a jacked-upvehicle.

● Do not start the vehicle when it israised on the jack.

● Clean wheel nuts and thread witha clean cloth before mounting thewheel.

9 Warning

Do not grease wheel bolt, wheelnut and wheel nut cone.

1. Disengage wheel nut caps with ascrewdriver and remove. Pull offthe wheel cover.

206 Vehicle care

2. Fold out the wheel wrench andinstall ensuring that it locatessecurely and loosen each wheelnut by half a turn.

3. Ensure the jack is correctlypositioned under the relevantvehicle jacking point.Depending on the equipment, firstremove the covers from thejacking points.

4. Set the jack to the necessaryheight. Position it directly belowthe jacking point in a manner thatprevents it from slipping.

Attach wheel wrench and with thejack correctly aligned rotate wheelwrench until wheel is clear of theground.

5. Unscrew the wheel nuts.6. Change the wheel. Spare wheel

3 207.

7. Screw on the wheel nuts.8. Lower the vehicle and remove

jack.9. Install the wheel wrench ensuring

that it locates securely and tighteneach nut in a crosswisesequence. Tightening torque is140 Nm.

10. Align the valve hole in the wheelcover with the tyre valve beforeinstalling.Install wheel nut caps.Install centre cap on alloy wheels.

11. Install vehicle jacking point coveron versions with sill panelling.

12. Stow the replaced wheel 3 207and the vehicle tools 3 194.

13. Check the tyre pressure of theinstalled tyre and the wheel nuttorque as soon as possible.

Have the defective tyre renewed orrepaired as soon as possible.

Vehicle care 207

Jacking position for lifting platform

Rear arm position of the liftingplatform centrically under the recessof the sill.

Front arm position of the liftingplatform at the underbody.

Spare wheelSome vehicles are equipped with atyre repair kit instead of a spare wheel3 202.If mounting a spare wheel, which isdifferent from the other wheels, thiswheel might be classified as atemporary spare wheel and thecorresponding speed limits apply,even though no label indicates this.Seek the assistance of a workshop tocheck the applicable speed limit.The spare wheel has a steel rim.

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

The spare wheel is located in the loadcompartment beneath the floorcovering. It is secured with a wing nut.

Stowing a damaged full sizewheel in the load compartmentThe spare wheel well is not designedfor other tyre sizes than the sparewheel.

208 Vehicle care

A damaged full size wheel must bestowed in the load compartment andsecured with a strap. Vehicle tools3 194.To secure the wheel:1. Position the wheel in the middle of

the load compartment.2. Place the loop end of the strap

through the lashing eye on oneside.

3. Place the hook end of the strapthrough the loop and pull it untilthe strap is fastened securely tothe lashing eye.

4. Insert the strap through thespokes of the wheel as shown inthe illustration.

5. Mount the hook to the oppositelashing eye.

6. Tighten the strap and secure itusing the buckle.

9 Danger

Always drive with folded up andengaged rear seat backrests whenstowing a damaged full size wheelin the load compartment.

Temporary spare wheel

Caution

The use of the temporary sparewheel could affect driveability.Have the defective tyre renewedor repaired as soon as possible.

Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.If your vehicle gets a flat tyre on therear while towing another vehicle,mount the temporary spare wheel atthe front and the full size tyre at therear.Tyre chains 3 201.

Spare wheel with directional tyreIf possible, fit directional tyres suchthat they roll in the direction of travel.The rolling direction is indicated by asymbol (e.g. an arrow) on thesidewall.

Vehicle care 209

The following applies to tyres fittedopposing the rolling direction:● Driveability may be affected.

Have the defective tyre renewedor repaired as soon as possibleand fit it instead of the sparewheel.

● Drive particularly carefully on wetand snow-covered roadsurfaces.

Jump startingDo not start with a quick charger.A vehicle with a discharged batterycan be started using jump leads andthe battery of another vehicle.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid containssulphuric acid which can causeinjuries and damage in the eventof direct contact.

● Never expose the battery tonaked flames or sparks.

● A discharged battery can alreadyfreeze at a temperature of 0 °C.Defrost the frozen battery beforeconnecting jump leads.

● Wear eye protection andprotective clothing whenhandling a battery.

● Use a booster battery with thesame voltage (12 Volts). Itscapacity (Ah) must not be muchless than that of the dischargedbattery.

● Use jump leads with insulatedterminals and a cross section ofat least 16 mm2 (25 mm2 fordiesel engines).

● Do not disconnect the dischargedbattery from the vehicle.

● Switch off all unnecessaryelectrical consumers.

● Do not lean over the batteryduring jump starting.

● Do not allow the terminals of onelead to touch those of the otherlead.

● The vehicles must not come intocontact with each other duringthe jump starting process.

210 Vehicle care

● Apply the parking brake,transmission in neutral,automatic transmission in P.

● Open the positive terminalprotection caps of both batteries.

Lead connection order:1. Connect the red lead to the

positive terminal of the boosterbattery.

2. Connect the other end of the redlead to the positive terminal of thedischarged battery.

3. Connect the black lead to thenegative terminal of the boosterbattery.

4. Connect the other end of the blacklead to a vehicle grounding point,such as the engine block or anengine mounting bolt. Connect asfar away from the dischargedbattery as possible, however atleast 60 cm.

Route the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After five minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval of1 minute.

3. Allow both engines to idle forapprox. three minutes with theleads connected.

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

Vehicle care 211

TowingTowing the vehicle

Disengage cap by using ascrewdriver and remove.The towing eye is stowed with thevehicle tools 3 194.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.Attach a tow rope – or better still a towrod – to the towing eye.The towing eye must only be used fortowing and not for recovering thevehicle.Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.

Caution

Never tow a vehicle equipped withAll Wheel Drive (AWD) with thefront or rear tyres on the road. Ifyou tow a vehicle equipped withAWD while the front or rear tyresare rolling on the road, the drivesystem in the vehicle could beseverely damaged. When towingvehicles equipped with AWD, allfour tyres must not be in contactwith the road.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation system 3 126 andclose the windows.

212 Vehicle care

Vehicles with manual transmission:The vehicle must be towed facingforwards. The maximum speed is50 mph. In all other cases, and whenthe transmission is defective, the frontaxle must be raised off the ground.Vehicles with automatic transmission:Do not tow the vehicle using a towingeye. Towing with a tow rope couldcause severe automatic transmissiondamage. When towing vehicles withautomatic transmission, use flat bedor wheel lift equipment.Seek the assistance of a workshop.After towing, unscrew the towing eye.Insert cap and close cap.

Towing another vehicle

Disengage the cap by using ascrewdriver and remove.The towing eye is stowed with thevehicle tools 3 194.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.The lashing eye at the rearunderneath the vehicle must never beused as a towing eye.Attach a tow rope – or even better atow bar – to the towing eye.The towing eye must only be used fortowing and not for recovering avehicle.

Vehicle care 213

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

After towing, unscrew the towing eye.Insert cap at the bottom and engagecap.

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use de-icing agent only whenabsolutely necessary, as this has adegreasing effect and impairs lockfunction. After using a de-icing agent,have the locks regreased by aworkshop.

WashingThe paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic vehiclewashes, select a programme thatincludes waxing.Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.

If using a vehicle wash, comply withthe vehicle wash manufacturer'sinstructions. The windscreen wiperand rear window wiper must beswitched off. Remove antenna andexternal accessories such as roofracks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.

Caution

Always use a cleaning agent witha pH value of 4 to 9.Do not use cleaning agents on hotsurfaces.

Have the door hinges of all doorsgreased by a workshop.Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.

214 Vehicle care

Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

Polishing and waxingWax the vehicle regularly (at thelatest when water no longer beads).Otherwise, the paintwork will dry out.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone forms aprotective film, making waxingunnecessary.Plastic body parts must not be treatedwith wax or polishing agents.

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window frominside, always wipe in parallel to theheating element to prevent damage.For mechanical removal of ice, use asharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.Clean smearing wiper blades with asoft cloth and window cleaner.Remove dirt residues from smearingwiper blades by using a soft cloth andwindow cleaner. Also make sure toremove any residues such as wax,insect residues and similar from thewindow.Ice residues, pollution and continuouswiping on dry windows will damage oreven destroy the wiper blades.

Wheels and tyresDo not use high-pressure jetcleaners.Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out by aworkshop.

Vehicle care 215

Before and after winter, wash theunderbody and have the protectivewax coating checked.

Liquid gas system

9 Danger

Liquid gas is heavier than air andcan collect in sink points.Take care when performing workat the underbody in a pit.

For painting work and when using adrying booth at a temperature above60 °C, the liquid gas system must becompletely evacuated.Do not make any modifications to theliquid gas system.

Towing equipmentDo not clean the coupling ball bar witha steam-jet or high-pressure jetcleaner.

Rear carrier systemClean the rear carrier system with asteam-jet or high-pressure jet cleanerat least once a year.

Operate the rear carrier systemperiodically if not in regular use, inparticular during winter.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.Clean the leather upholstery withclear water and a soft cloth. In case ofheavy soiling, use leather care.The instrument cluster and thedisplays should only be cleaned usinga soft damp cloth. If necessary use aweak soap solution.Clean fabric upholstery with avacuum cleaner and brush. Removestains with an upholstery cleaner.Clothing fabrics may not becolourfast. This could cause visiblediscolourations, especially on light-coloured upholstery. Removablestains and discolourations should becleaned as soon as possible.

Clean seat belts with lukewarm wateror interior cleaner.

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, e.g. zips,belts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

216 Service and maintenance

Service andmaintenance

General information ................... 216Service information .................. 216

Recommended fluids, lubricantsand parts .................................... 217

Recommended fluids andlubricants ................................ 217

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.Service display 3 86.

European service intervalsMaintenance of your vehicle isrequired every 20,000 miles or afterone year, whichever occurs first,unless otherwise indicated in theservice display.A shorter service interval can be validfor severe driving behaviour, e.g. fortaxis and police vehicles.The European service intervals arevalid for the following countries:

Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,Iceland, Ireland, Italy, Latvia,Liechtenstein, Lithuania,Luxembourg, Macedonia, Malta,Monaco, Montenegro, Netherlands,Norway, Poland, Portugal, Romania,San Marino, Serbia, Slovakia,Slovenia, Spain, Sweden,Switzerland, United Kingdom.Service display 3 86.

International service intervalsMaintenance of your vehicle isrequired every 10,000 miles or afterone year, whichever occurs first,unless otherwise indicated in theservice display.Severe operating conditions exist ifone or more of the followingcircumstances occur frequently: Coldstarting, stop and go operation, traileroperation, mountain driving, drivingon poor and sandy road surfaces,increased air pollution, presence ofairborne sand and high dust content,

Service and maintenance 217

driving at high altitude and largevariations of temperature. Underthese severe operating conditions,certain service work may be requiredmore frequently than the regularservice interval.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.Service display 3 86.

ConfirmationsConfirmation of service is recorded inthe Service and warranty booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.Make sure that the Service andwarranty booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service interval with remainingengine oil life durationThe service interval is based onseveral parameters depending onusage.The service display lets you knowwhen to change the engine oil.Service display 3 86.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that meet therecommended specifications.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oilaging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.

218 Service and maintenance

Dexos is the newest engine oil qualitythat provides optimum protection forgasoline and diesel engines. If it isunavailable, engine oils of other listedqualities have to be used.Recommendations for gasolineengines are also valid forCompressed Natural Gas (CNG),Liquified Petroleum Gas (LPG) andEthanol (E85) fuelled engines.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 221.

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isprohibited, since it can cause long-term engine damage under certainoperating conditions.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 221.

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesThe SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures, e.g. SAE 5W-30. The firstfigure, followed by a W, indicates thelow temperature viscosity and thesecond figure the high temperatureviscosity.Select the appropriate viscosity gradedepending on the minimum ambienttemperature 3 221.All of the recommended viscositygrades are suitable for high ambienttemperatures.

Coolant and antifreezeUse only organic acid type-long lifecoolant (LLC) antifreeze approved forthe vehicle. Consult a workshop.The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -28 °C. In

northern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37 °C. This concentrationshould be maintained all year round.The use of additional coolantadditives that intend to give additionalcorrosion protection or seal againstminor leaks can cause functionproblems. Liability for consequencesresulting from the use of additionalcoolant additives will be rejected.

Washer fluidUse only washer fluid approved forthe vehicle to prevent damage ofwiper blades, paintwork, plastic andrubber parts. Consult a workshop.

Brake and clutch fluidOver time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.

Technical data 219

Technical data

Vehicle identification .................. 219Vehicle Identification Number .. 219Identification plate ................... 219Engine identification ................ 220

Vehicle data ............................... 221Recommended fluids andlubricants ................................ 221

Engine data ............................. 224Performance ............................ 226Vehicle weight ......................... 227Vehicle dimensions ................. 228Capacities ................................ 229Tyre pressures ........................ 230

Vehicle identificationVehicle IdentificationNumber

The Vehicle Identification Number islocated in the engine compartment.The Vehicle Identification Numbermay be embossed on the instrumentpanel, visible through the windscreen.

Identification plate

The identification plate is located onthe front left or right door frame.

220 Technical data

Information on identification label:1 : manufacturer2 : type approval number3 : vehicle Identification Number4 : permissible gross vehicle weight

rating in kg5 : permissible gross train weight

in kg6 : maximum permissible front axle

load in kg7 : maximum permissible rear axle

load in kg

Engine identificationThe technical data tables show theengine identifier code. Engine data3 224.To identify the respective engine,refer to the engine power in the EECCertificate of Conformity providedwith your vehicle or other nationalregistration documents.The Certificate of Conformity showsthe engine identifier code, othernational publications may show theengineering code. Check pistondisplacement and engine power toidentify the respective engine.

Technical data 221

Vehicle dataRecommended fluids and lubricantsEuropean service schedule

Required engine oil qualityAll European countries with European service interval 3 216

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines

dexos 1 – –

dexos 2 ✔ ✔

In case dexos quality is unavailable you may use max. one litre engine oil quality ACEA C3 once between each oil change.

Engine oil viscosity gradesAll European countries with European service interval 3 216

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

222 Technical data

International service schedule

Required engine oil qualityAll countries with international service interval 3 216


Diesel engines

dexos 1 (if available) ✔ –

dexos 2 ✔ ✔

In case dexos quality is unavailable you may use the oil qualities listed below:

All countries with international service interval 3 216


Diesel engines

GM-LL-A-025 ✔ –

GM-LL-B-025 – ✔



Diesel engines

ACEA A3/B3 ✔ –

ACEA A3/B4 ✔ ✔

Technical data 223


ACEA C3 ✔ ✔

API SM ✔ –

API SN resource conserving ✔ –

Engine oil viscosity gradesAll countries with international service interval 3 216

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

down to -20 °C SAE 10W-301) or SAE 10W-401)

1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.

224 Technical data

Engine dataEngine identifier code B14NET B14NET B14XFT B16XER A18XERSales designation 1.4 1.4 LPG 1.4 1.6 1.8Engineering code B14NET B14NET B14XFT B16XER A18XER

Piston displacement [cm3] 1364 1364 1399 1598 1796

Engine power [kW] 103 103 109 85 103

at rpm 4900-6000 4900-6000 4900-6000 6000 6200

Torque [Nm] 200 200 235 155 178

at rpm 1850-4900 1850-4900 1850-4900 4000 3800

Fuel type Petrol Liquid Gas/Petrol Petrol Petrol Petrol

Octane rating RON2)

recommended 95 95 95 95 95

possible 98 98 98 98 98

possible 91 91 91 91 91

Additional fuel type – Liquid gas (LPG) – – –

2) A country-specific label at the fuel filler flap can supersede the engine-specific requirement.

Technical data 225

Engine identifier code B16DTHB16DTU B16DTNSales designation 1.61.6 1.6Engineering code B16DTHB16DTH B16DTH

Piston displacement [cm3] 15981598 1598

Engine power [kW] 10081 81

at rpm 3500-40003500 3500

Torque [Nm] 320300 300

at rpm 2000-22502000-2250 2000-2250

Fuel type DieselDiesel Diesel

Octane rating RON2)

recommended

possible

possible

Additional fuel type –– –

2) A country-specific label at the fuel filler flap can supersede the engine-specific requirement.

226 Technical data

Performance

Engine B14NETB14NETLPG B14XFT B16XER A18XER

Maximum speed [mph]

Manual transmission 121/1153) 122 – 106 112

Automatic transmission 118 – 120 – 112

34) Vehicles with All-wheel drive system.Vehicles with All-wheel drive system.

Engine B16DTH B16DTU B16DTN

Maximum speed [mph]

Manual transmission 118/1163)4) 112 111

Automatic transmission 117 – –


Technical data 227

Vehicle weightKerb weight, basic model without any optional equipment

Engine Manual transmission Automatic transmission

[kg] B14NET 1319/13704) 1334

B14NETLPG

1375 –

B14XFT – 1406

B16XER 1280 –

A18XER 1305 1392

B16DTU 1374 –

B16DTN 1374 –

B16DTH 1374/14293)4) 1387


Optional equipment and accessories increase the kerb weight.Loading information 3 73.

228 Technical data

Vehicle dimensionsLength [mm] 4271

Width without exterior mirrors [mm] 1781

Width with two exterior mirrors [mm] 2038

Height (without antenna) [mm] 1662/16715)

Length of load compartment floor [mm] 731

Length of load compartment with folded rear seats [mm] 1428

Load compartment width [mm] 914

Load compartment height [mm] 808

Wheelbase [mm] 2555

Turning circle diameter [m] 10.9/11.3 5)

5) Depending on wheel size.

Technical data 229

CapacitiesEngine oil

Engine B14NET B14NETLPG

B14XFT B16XER A18XER B16DTH,B16DTU,B16DTN

including Filter [l] 4.0 4.0 4.0 4.5 4.5 5.0

between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0

Fuel tank

Engine B14NET B14NETLPG

B14XFT B16XER A18XER B16DTH,B16DTU,B16DTN

Petrol/diesel, refilling quantity [l] 53 53 53 53 53 52

LPG, refilling quantity [l] – 34 – – – –

230 Technical data

Tyre pressuresComfort with up to 3 people ECO with up to 3 people With full load

Engine Tyres front rear front rear front rear[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B14NET,B14NET LPG,B16XER,A18XER

215/60 R17, 220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 280/2.8 (41) 270/2.7(39)

300/3.0(44)

215/55 R18

205/70 R16,215/65 R16

200/2.0 (29) 200/2.0 (29) 270/2.7 (39) 280/2.8 (41) 270/2.7(39)

300/3.0(44)

225/45 R19 240/2.4 (35) 240/2.4 (35) 270/2.7 (39) 280/2.8 (41) 270/2.7(39)

280/2.8(41)

Technical data 231

Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B14XFT,B16DTH,B16DTU,B16DTN

215/60R17, 240/2.4 (35) 240/2.4 (35) 270/2.7 (39) 280/2.8 (41) 270/2.7(39)

300/3.0(44)

215/55 R18

205/70 R16,215/65 R16

220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 280/2.8 (41) 270/2.7(39)

300/3.0(44)

225/45 R19 240/2.4 (35) 240/2.4 (35) 270/2.7 (39) 280/2.8 (41) 270/2.7(39)

280/2.8(41)

All Temporary sparewheel125/70 R16

420/4.2 (60) 420/4.2 (60) – – 420/4.2(60)

420/4.2(60)

232 Customer information

Customerinformation

Customer information ................ 232Declaration of conformity ......... 232Collision damage repair ........... 234Software acknowledgement .... 234Registered trademarks ............ 235

Vehicle data recording and pri‐vacy ........................................... 236

Event data recorders ............... 236Radio Frequency Identification(RFID) ..................................... 237

Customer informationDeclaration of conformityTransmission systemsThis vehicle has systems thattransmit and/or receive radio wavessubject to Directive 1999/5/EC or2014/53/EU. These systems are incompliance with the essentialrequirements and other relevantprovisions of Directive 1999/5/EC or2014/53/EU. Copies of the originalDeclarations of Conformity can beobtained on our website.

Customer information 233

Jack


Collision damage repairPaint thicknessDue to production techniques, thethickness of the paint can varybetween 50 and 400 µm.Therefore, different paint thickness isno indicator for a collision damagerepair.

Software acknowledgementCertain OnStar components includelibcurl and unzip software and otherthird party software. Below are thenotices and licenses associated withlibcurl and unzip and for other thirdparty software please see http://www.lg.com/global/support/opensource/index.

libcurlCopyright and permission noticeCopyright (c) 1996 - 2010, DanielStenberg, <[email protected]>.All rights reserved.

Permission to use, copy, modify, anddistribute this software for anypurpose with or without fee is herebygranted, provided that the abovecopyright notice and this permissionnotice appear in all copies.The software is provided "as is",without warranty of any kind, expressor implied, including but not limited tothe warranties of merchantability,fitness for a particular purpose andnoninfringement of third party rights.In no event shall the authors orcopyright holders be liable for anyclaim, damages or other liability,whether in an action of contract, tortor otherwise, arising from, out of or inconnection with the software or theuse or other dealings in the software.Except as contained in this notice, thename of a copyright holder shall notbe used in advertising or otherwise topromote the sale, use or otherdealings in this Software without priorwritten authorization of the copyrightholder.

unzipThis is version 2005-Feb-10 of theInfo-ZIP copyright and license. Thedefinitive version of this documentshould be available at ftp://ftp.info-zip.org/pub/infozip/license.htmlindefinitely.Copyright (c) 1990-2005 Info-ZIP. Allrights reserved.For the purposes of this copyright andlicense, “Info-ZIP” is defined as thefollowing set of individuals:Mark Adler, John Bush, Karl Davis,Harald Denker, Jean-Michel Dubois,Jean-loup Gailly, Hunter Goatley, EdGordon, Ian Gorman, Chris Herborth,Dirk Haase, Greg Hartwig, RobertHeath, Jonathan Hudson, PaulKienitz, David Kirschbaum, JohnnyLee, Onno van der Linden, IgorMandrichenko, Steve P. Miller, SergioMonesi, Keith Owens, GeorgePetrov, Greg Roelofs, Kai UweRommel, Steve Salisbury, DaveSmith, Steven M. Schweda, ChristianSpieler, Cosmin Truta, AntoineVerheijen, Paul von Behren, RichWales, Mike White.


This software is provided “as is,”without warranty of any kind, expressor implied. In no event shall Info-ZIPor its contributors be held liable forany direct, indirect, incidental, specialor consequential damages arising outof the use of or inability to use thissoftware.Permission is granted to anyone touse this software for any purpose,including commercial applications,and to alter it and redistribute it freely,subject to the following restrictions:1. Redistributions of source code

must retain the above copyrightnotice, definition, disclaimer, andthis list of conditions.

2. Redistributions in binary form(compiled executables) mustreproduce the above copyrightnotice, definition, disclaimer, andthis list of conditions indocumentation and/or othermaterials provided with thedistribution. The sole exception tothis condition is redistribution of astandard UnZipSFX binary(including SFXWiz) as part of aself-extracting archive; that is

permitted without inclusion of thislicense, as long as the normalSFX banner has not beenremoved from the binary ordisabled.

3. Altered versions--including, butnot limited to, ports to newoperating systems, existing portswith new graphical interfaces, anddynamic, shared, or static libraryversions--must be plainly markedas such and must not bemisrepresented as being theoriginal source. Such alteredversions also must not bemisrepresented as being Info-ZIPreleases--including, but notlimited to, labeling of the alteredversions with the names “Info-ZIP” (or any variation thereof,including, but not limited to,different capitalizations), “PocketUnZip,” “WiZ” or “MacZip” withoutthe explicit permission of Info-ZIP.Such altered versions are furtherprohibited from misrepresentative

use of the Zip-Bugs or Info-ZIP e-mail addresses or of the Info-ZIPURL(s).

4. Info-ZIP retains the right to usethe names “Info-ZIP,” “Zip,”“UnZip,” “UnZipSFX,” “WiZ,”“Pocket UnZip,” “Pocket Zip,” and“MacZip” for its own source andbinary releases.

Registered trademarksApple Inc.Apple CarPlay™ is a trademark ofApple Inc.App Store® is a registered trademarkof Apple Inc.iPhone®, iPod® and Siri® areregistered trademarks of Apple Inc.Aupeo! GmbHAUPEO® is a registered trademark ofthe Aupeo! GmbH.Bluetooth SIG, Inc.Bluetooth® is a registered trademarkof Bluetooth SIG, Inc.EnGIS Technologies, Inc.BringGo® is a registered trademark ofEnGIS Technologies, Inc.


Google Inc.Android™ and Google Play™ Storeare trademarks of Google Inc.Verband der Automobilindustrie e.V.AdBlue® is a registered trademark ofthe VDA.

Vehicle data recordingand privacyEvent data recordersData storage modules in thevehicleA large number of electroniccomponents of your vehicle containdata storage modules temporarily orpermanently storing technical dataabout the condition of the vehicle,events and errors. In general, thistechnical information documents thecondition of parts, modules, systemsor the environment:● Operating conditions of system

components (e.g. filling levels)● Status messages of the vehicle

and its single components (e.g.number of wheel revolutions /rotational speed, deceleration,lateral acceleration)

● Dysfunctions and defects inimportant system components

● Vehicle reactions in particulardriving situations (e.g. inflation ofan airbag, activation of thestability regulation system)

● Environmental conditions (e.g.temperature)

These data are exclusively technicaland help identifying and correctingerrors as well as optimizing vehiclefunctions.Motion profiles indicating travelledroutes cannot be created with thesedata.If services are used (e.g. repairworks, service processes, warrantycases, quality assurance),employees of the service network(manufacturer included) are able toread out this technical informationfrom the event and error data storagemodules applying special diagnosticdevices. If required, you will receivefurther information at theseworkshops. After an error has beencorrected, the data are deleted fromthe error storage module or they areconstantly overwritten.


When using the vehicle, situationsmay occur in which these technicaldata related to other information(accident report, damages on thevehicle, witness statements etc.) maybe associated with a specific person -possibly, with the assistance of anexpert.Additional functions contractuallyagreed upon with the client (e.g.vehicle location in emergency cases)allow the transmission of particularvehicle data from the vehicle.

Radio FrequencyIdentification (RFID)RFID technology is used in somevehicles for functions such as tyrepressure monitoring and ignitionsystem security. It is also used inconnection with conveniences suchas radio remote controls for doorlocking/unlocking and starting, and in-vehicle transmitters for garage dooropeners. RFID technology inVauxhall vehicles does not use orrecord personal information or linkwith any other Vauxhall systemcontaining personal information.

238

Index AAccessories and vehicle

modifications .......................... 176Adaptive forward lighting ..... 95, 118Adjustable air vents ................... 130Airbag and belt tensioners ........... 91Airbag deactivation ................ 51, 92Airbag label................................... 46Airbag system .............................. 46Air conditioning regular

operation ................................ 131Air conditioning system .............. 126Air intake .................................... 130Air vents...................................... 130All-wheel drive ........................... 146Antilock brake system ................ 147Antilock brake system (ABS) ....... 92Anti-theft alarm system ................ 29Anti-theft locking system .............. 29Appearance care........................ 213Automatic anti-dazzle .................. 33Automatic light control ............... 115Automatic locking ........................ 27Automatic transmission ............. 142Autostop..................................... 137Auxiliary heater........................... 129

BBattery discharge protection ...... 124Battery voltage ........................... 103

Bicycle rack.................................. 60Bonnet ....................................... 178Brake and clutch fluid................. 217Brake and clutch system ............. 92Brake assist ............................... 148Brake fluid .................................. 181Brakes ............................... 147, 181Breakdown.................................. 211Bulb replacement ....................... 185

CCapacities .................................. 229Catalytic converter ..................... 141Central locking system ................ 23Centre console storage ............... 60Changing tyre and wheel size . . . 201Charging system .......................... 92Child locks ................................... 28Child restraint installation

locations ................................... 53Child restraints.............................. 52Child restraint systems ................ 52Climate control ............................. 15Climate control systems............. 125Clock............................................. 80Code........................................... 102Collision damage repair.............. 234Control indicators.......................... 86Control of the vehicle ................. 133Controls........................................ 76

239

Convex shape .............................. 31Coolant and antifreeze............... 217Cruise control ...................... 95, 151Cupholders .................................. 58Curtain airbag system .................. 50

DDanger, Warnings and Cautions . . . 4Daytime running lights ............... 118Declaration of conformity............ 232Delayed locking............................ 26Descent control system ....... 93, 150Diesel fuel system bleeding ....... 183Diesel particle filter .................... 141Door open .................................... 96Doors............................................ 28Driver assistance systems.......... 151Driver Information Centre............. 96Driving characteristics and

towing tips .............................. 172Driving hints................................ 133

EElectric adjustment ...................... 31Electrical system......................... 189Electronic climate control system 127Electronic driving programmes . . 144Electronic key system................... 21Electronic Stability Control.......... 149Electronic Stability Control and

Traction Control system............ 93

Electronic Stability Control off....... 93End-of-life vehicle recovery ....... 177Engine compartment fuse box ... 189Engine coolant ........................... 180Engine coolant temperature

gauge ....................................... 85Engine data ............................... 224Engine exhaust .......................... 140Engine identification................... 220Engine oil ................... 179, 217, 221Engine oil pressure ...................... 94Entry lighting .............................. 123ERA GLONASS.......................... 112Event data recorders.................. 236Exit lighting ................................ 124Exterior care .............................. 213Exterior light ................................. 95Exterior lighting .................... 12, 114Exterior mirrors............................. 31

FFault ........................................... 144First aid kit ................................... 73Fixed air vents ........................... 130Flex-Fix system............................ 60Fog light ....................................... 95Fog lights ................................... 186Folding mirrors ............................. 31Following distance indication...... 156Forward collision alert................. 154

Front airbag system ..................... 49Front fog lights ........................... 121Front seats.................................... 39Front storage................................ 59Fuel............................................. 165Fuel consumption - CO2-

Emissions ............................... 171Fuel for diesel engines .............. 165Fuel for liquid gas operation....... 166Fuel for petrol engines ............... 165Fuel gauge ................................... 84Fuel selector ................................ 85Fuses ......................................... 189

GGauges......................................... 83Gear shifting................................. 93General information ................... 172Glovebox ..................................... 58Glove box lighting....................... 123

HHalogen headlights .................... 185Hand brake................................. 147Hazard warning flashers ............ 120Headlight flash ........................... 116Headlight range adjustment ...... 117Headlights when driving abroad 117Head restraint adjustment ............. 8Head restraints ............................ 38Heated mirrors ............................. 32

240

Heated rear window ..................... 35Heated steering wheel ................. 76Heating ........................................ 42Heating and ventilation system . 125High beam ........................... 95, 115High beam assist.................. 95, 116Hill start assist ........................... 148Horn ....................................... 13, 77

IIdentification plate ..................... 219Ignition switch positions ............. 134Immobiliser ............................ 30, 94Indicators...................................... 83Info display................................. 100Information displays...................... 96Initial drive information.................... 6Instrument panel fuse box ......... 191Instrument panel illumination

control .................................... 122Instrument panel overview ........... 10Interior care ............................... 215Interior lighting............................ 122Interior lights .............................. 122Interior mirrors.............................. 32Interruption of power supply ...... 144Introduction .................................... 3ISOFIX child restraint systems .... 56

JJump starting ............................. 209

KKey, memorised settings.............. 23Keys ............................................. 19Keys, locks................................... 19

LLane departure warning....... 93, 164Lashing eyes ............................... 72Lighting features......................... 123Light switch ................................ 114Load compartment ................ 28, 70Load compartment cover ............. 72Load compartment fuse box ...... 193Loading information ..................... 73Low fuel ....................................... 94

MMalfunction indicator light ............ 92Manual anti-dazzle ...................... 32Manual mode ............................. 143Manual transmission .................. 145Manual windows .......................... 33Memorised settings...................... 23Midlevel display............................ 96Mirror adjustment ........................... 8Misted light covers ..................... 122

NNew vehicle running-in .............. 133Number plate light ..................... 188

OObject detection systems........... 157Odometer ..................................... 83Oil, engine.......................... 217, 221OnStar........................................ 108Outside temperature .................... 79Overrun cut-off ........................... 137

PParking ................................ 18, 139Parking assist ............................ 157Parking brake ............................ 147Particulate filter........................... 141Performance .............................. 226Performing work ........................ 178Pollen filter ................................. 130Power button.............................. 134Power outlets ............................... 82Power steering fluid.................... 180Power windows ............................ 34Preheating ................................... 93Puncture..................................... 205

RRadio Frequency Identification

(RFID)..................................... 237Radio remote control ................... 20Reading lights ............................ 123Rear carrier system...................... 60Rear floor storage cover .............. 72Rear fog light ....................... 95, 121

241

Rear view camera ...................... 159Rear window wiper/washer .......... 79Recommended fluids and

lubricants ........................ 217, 221Refuelling ................................... 168Registered trademarks............... 235Retained power off..................... 135Reversing lights ......................... 121Ride control systems.................. 148Roof.............................................. 36Roof load...................................... 73Roof rack ..................................... 73

SSeat adjustment ....................... 6, 40Seat belt ........................................ 8Seat belt reminder ....................... 91Seat belts ..................................... 43Seat heating................................. 42Seat position ................................ 39Selector lever ............................. 142Service ....................................... 131Service display ............................ 86Service information .................... 216Side airbag system ...................... 49Software acknowledgement....... 234Spare wheel ............................... 207Speed limiter......................... 95, 153Speedometer ............................... 83Starting and operating................ 133

Starting off ................................... 16Starting the engine .................... 136Steering...................................... 133Steering wheel adjustment ...... 9, 76Steering wheel controls ............... 76Stop-start system........................ 137Storage compartments................. 58Sunglasses storage ..................... 59Sunroof ........................................ 36Sunvisor lights ........................... 123Sun visors .................................... 35Symbols ......................................... 4

TTachometer ................................. 84Tail lights ................................... 187Three-point seat belt .................... 44Tools .......................................... 194Top-tether fastening eyes ............ 57Tow bar....................................... 172Towing................................ 172, 211Towing another vehicle ............. 212Towing equipment ..................... 173Towing the vehicle ..................... 211Traction Control system ............. 148Traction Control system off........... 93Traffic sign assistant............. 96, 160Trailer towing ............................. 172Transmission ............................... 16Transmission display ................. 142

Tread depth ............................... 200Trip odometer .............................. 83Turn and lane-change signals ... 121Turn signal ................................... 90Tyre chains ................................ 201Tyre designations ...................... 195Tyre pressure ............................ 195Tyre pressure monitoring

system............................... 94, 196Tyre pressures ........................... 230Tyre repair kit ............................. 202

UUltrasonic parking assist............. 157Underseat storage ....................... 60Upholstery.................................. 215Uplevel display............................. 96Using this manual .......................... 3

VValet mode................................. 100Vehicle battery ........................... 182Vehicle checks............................ 178Vehicle data................................ 221Vehicle data recording and

privacy..................................... 236Vehicle detected ahead................ 95Vehicle dimensions .................... 228Vehicle Identification Number .... 219Vehicle jack................................ 194Vehicle messages ..................... 102

242

Vehicle personalisation ............. 104Vehicle security............................ 29Vehicle specific data ...................... 3Vehicle storage........................... 177Vehicle tools............................... 194Vehicle unlocking ........................... 6Vehicle weight ........................... 227Ventilation................................... 125

WWarning chimes ......................... 103Warning lights............................... 83Warning triangle .......................... 72Washer and wiper systems ......... 14Washer fluid ............................... 181Wheel changing ......................... 205Wheel covers ............................. 201Wheels and tyres ....................... 195Windows....................................... 33Windscreen................................... 33Windscreen wiper/washer ........... 77Winter tyres ............................... 195Wiper blade replacement .......... 184

Copyright by General Motors UK Ltd.

The information contained in this publication is effective as of the date indicated below. General Motors UK Ltd. reserves the right to make changes to the technical specifications,features and design of the vehicles relative to the information contained in this publication, as well as changes to the publication itself.

Edition: August 2016, General Motors UK Ltd.

Printed on chlorine-free bleached paper.

*ID-VMKAORIE1608-EN*

ID-VMKAORIE1608-en

Documents

Vauxhall Mokka X Owner's Manual...Radio remote control 3 20, Central locking system 3 23, Electronic key system 3 21, Load compartment 3 28. Seat adjustment Longitudinal adjustment