A09€¦ · A09.BD V.2011/November 1 ... pulleys, projecting set screws, keys and other ... WOLTER Belt driven axial flow fan motors are squirrel-cage induction

Axial Flow FansBelt Driven

A09.BD #

1A09.BD V.2011/November

Table of Content

Subject to change without prior notice.

ContentsPage 1

Wolter Belt Driven Axial FanPage 2~4

Fan Performance CurvesPage 5~33

Fan Type CodePage 2

DimensionsPage 34

2 A09.BD V.2011/November

Axial Flow FansTechnical information

AXV, Belt Driven

Fan type codeAXV-AL 450-7 /26° LH100 -2 SU

Air flow and form of running S, D, SU, SO, DU, DO

number of poles

Casing versionSH = Short-cased LH1 = Long-cased

Pitch angle

AXV: impeller-Ø and number of blades315 ... 1600 - 3, 5, 6, 7, 9, 10, 12, 14

Axial impeller blade type, material

Wolter Belt Driven Axial Fan

The Wolter range of Belt driven fans are designed for application that required motor to be isolated from the airstreams. It is specially developed to meet the need for an axial fan:

> where it can handle heavy corrosive fumes, hot air and gas, saturated and dust-laden atmospheres, which may normally detriment the life of the fan motor

> where air temperature in the system airstreams is critical> where fan speed can be adjusted by changing the pulley drive to achieve

performance> where a requirement of twin motors mounting

> where fan motors must be outside the air stream

QualityThe complete range of Belt driven axial fans, drives and accessories are produced to strict quality standards and tested in accordance with other internationally standards.

NoiseTo obtain the sound spectrum in the octave band mid-frequencies 63 Hz to 8000 Hz, the constants figure shown at the right side of the performance chart should be subtracting from the ‘overall’ sound power level (dBW) of the fan selected. The sound power level (dBW) and sound pressure level (dB) data appear in the fan curves are taken at a distance of three fans diameter.

Test method is in accordance with ISO 5801, AMCA 300. In-duct tests Method. The method of test is similar to the actual flow fan. However, the noise levels are +3dB to +5dB greater than that determines by Free Field or Reverberant Field testing

Product & PerformanceThe Wolter Belt driven axial fans’ diameter cover fifteen sizes - 315 to 1600.Fan capacity up to 200,000 cubic meter per Hour and operating at a static pressure of up to 1500 Pascal (Pa).

These belt driven axial flow fans can be fitted with guide vanes or multi-staged to increase performance. Fan size above 1600 can be supplied upon request.

The fans are fully tested and complied to: ISO 5801 and AMCA 210 for aerodynamic performance

Fan CasingThe standard fans casing are constructed from heavy gauge steel plate, hot dipped galvanized after manufactured to AS1650. The standard casing is of long type covering completely both the impeller and motor.

Fans sizes up to 630mm comes with screwed-on mounting feet. All casings are rolled and flanged simultaneously. Mounting feet for sizes 710mm and above are optional. All casing above size 710 comes with inspection door.

The fan drive unit and shaft housing are completely enclosed with heavy gauge hot dipped galvanised after manufactured.

Fan Impeller

The Belt driven axial fans impellers are of non overloading characteristics with aerodynamically shaped aerofoil blade constructed of high strength die-cast aluminium alloy similar to those axial impeller.

The maximum absorbed power for the selected pitch angle can read from the top right-hand corner of the charts. The peak absorbed power is shown in both kW and HP. However, for fans with fully enclosed guard, the performance can be obtained by adding 6° to the pitch angle reading.

Safety FeaturesAll fans are labelled with name plate securely attached on each fan showing the serial and model number, fan and drive duties, rotation of flow and date of manufacture. All belts, pulleys, projecting set screws, keys and other rotating external parts are properly guarded conforming to safety standards in accordance with Factory Act requirements.

Test Setups

ISO 5801 Figure 73bAMCA 210 Figure 12

Outlet chamber

Auxilliary Fan

Nozzles

Test Fan

Settlingmeans

Test Setups


Outlet chamber

Auxilliary Fan

Nozzles

Test Fan

Settlingmeans

Test Setups


Outlet chamber

Auxilliary Fan

Nozzles

Test Fan

Settlingmeans

Test Fan

AMCA 210 Figure 12ISO 5801 Figure 73b

3A09.BD V.2011/November

!"AXV Belt Driven

Shaft and Bearing HousingThe pedestal housing with two-bearing seating is machined at one setting. Misalignment of the bearings is thus avoided.

The shaft is of solid type, specially selected, turned, ground and polished steel to give tight, accurate bearing and hub fit. The shaft is oversized to prevent deflection and oscillation.

The two anti-friction bearings, double shielded and prepacked with lithium-base Alvania No.3 greased. Fully enclosed, sealed-for-life and therefore do not required maintenance. Bearing which is not grease packed will be provided with grease nipple brought to the outside casing with copper tubing.

Similar to those axial impeller, the number of blades can be varied to obtain maximum efficiency when operating at a relatively low pressure:

Fan Blades Variation (Solidities) Twin Motors MountingBelt driven fan with twin motor can be mounted in difference position to suit the site condition. Position as illustrated.

Multi-stage Belt Driven Axial Flow FansThe multi-stage axial flow fans comprising two or more single stage fans connected in series.

The contra-rotating multi-stage fans can develop 2.5 to 3 times higher pressures than a single stage fan of equal in size and speed. The first stage impeller usually mounted with right-hand blade and the second stage impeller will rotate in contra directions.

Twin motors mountingBelt driven fan with twin motor can be mounted in difference position to suit the site condition. Position as illustrated.

MotorStandard motor come with B3 foot mounted, supported on motor mounting plate outside the fan casing with stud to adjust alignment and tensioning. Large motor are placed on side way.

However, for larger frame motor, a grease nipple will be fitted to the outside the casing to facilitate lubrication.

Electrical wires are connected directly to the motor terminal box comply-ing with BS 4999 Part 20: 1972 for dust and weatherproof conditions. WOLTER Belt driven axial flow fan motors are squirrel-cage induction type, totally enclosed and air stream rated. Complied with IEC publication number 34-1, AS 1359, BS 3979: 1966, BS 5000 part99 (BS 2613), the relevant part of BS 4999, and are maximum continuously rated. They are also CSA approved. Insulation to Class F with Class B temperature rise (80°C) complying with BS 2757. For continuous operation in higher ambi-ent. Class H insulation winding rated 250 °C for 2 hrs (emergency) or 250 °C for 1 hrs (normal) is used.

Minimum IP54 enclosure as standard suitably for operation in ambient temperature of minus 10°C to plus 40°C. However, IP55 will be supplied for fully weatherproof and against harmful deposits of dust application.

The fan motor is fitted with anti-friction bearing, double shielded and pre-packed with lithium-base Alvania No.3 greased. Frame sizes up to D180 are fully enclosed, sealed-for-life and therefore do not required maintenance. Motor for uses in temperatures up to 200 deg C are fitted with C3 fit bearings.

Details information on ‘Degrees of Protection’, ‘Type of Insulation’, and ‘Wiring Connections’ are available for easy references

Electrical FeaturesThe motor is suitable for 220/380 volts, 50Hz supply as standard. Fans can be supplied single phase 50Hz depending upon motor size and temperature required. All motor selected are suitable for direct on line starting.

All motors have an integral terminal box. The correct cable selection is important, particularly when wiring the fans at the higher temperatures. Starting current will be about seven times full load current for direct-on-line starting and 2 to 2.5 times full load currents for star-delta starting

TropicalisationMotor windings are coated with resin varnishes which make the motor suitable for tropical atmospheres. Additional treatment can be carried out where motors are required to operate in severe tropical environments.

Thermal Protection MotorThermal protection in the form of thermistors can be incorporated in any of the squirrel-cage induction motor on request.

Wolter Axial Fan for Corrosive AtmosphereBeside aluminium alloy impellers, WOLTER also has a full range of “P” ranges of glass reinforced polypropylene (PP) impellers. These impellers are designed to give maximum volume flow with minimum noise and power consumption. Impellers of PP are flame retardant, certify under UL94 rating V-0, and good in chemical resistance.

For application where heavy corrosive atmospheres are to be handled, Wolter Belt driven fans can be supplied with any of the following systems, depending on the requirement. System 1Stainless steel casing with die cast aluminium alloy impellers. Fan range from 315 to 1600 diameters. System 2Stainless steel casing with injection moulded polypropylene impeller. Fan range from 315 to 1000 diameters. System 3Steel casing with additional protective layer of epoxy paint to all galvanised surfaces. Come with die cast aluminium alloy impellers. Fan range from 315 to 1600 diameters. System 4Steel casing with additional protective layer of epoxy paint to all galvanised surfaces. Come with injection moulded polypropylene impellers. Fan range from 315 to 1000 diameters.

Motor Mounting at Zero Position

Motor Mounting Side Way

Motor Mounting Position - Specify in degree

180 deg

0 deg

315 deg 45 deg

225 deg 135 deg

90 deg270 deg


Axial Flow FansTechnical information

AXV, Belt Driven

WOLTER Hazardous Location FansWolter hazardous Belt driven axial fan coupled with comprehensive range of motors for specific application. The fans motors are fully Certified by SAA & Dept. of Mines to suit non-sparking, Flame proof, dust ignition proof, and increased safety applications. To enable correct selection of fan type, full details of gas groups and zones should be supplied in the enquiry with any specification details.

Hazardous axial fans with ‘long’ casing are supplied with an inspection door for wiring to be taken direct through a special certify safety proof conduit to the motor terminal box. Short casing is wired directly to motor terminal box.

All standard fans impellers come with aluminium blade unless otherwise specific. The impeller can be of polypropylene to handle exhaust air, which contains combustible dusts, fibres, flying and explosive gas/ air mixtures.

Fan Code & ApplicationCode Ex ‘d’ I- Flameproof Motors for Industrial use - Certified by SAA for Class 1 Zone 1 - Approved for used in Underground Coal & Shale Mine by : Gas Group I - NSW. Dept. Minerals & Energy Coalfields Div. - Qld. Dept. Mines - Approved by various International stds.for use in underground Coal Mining.

Code Ex ‘d’ IU

- Flameproof Motors for Industrial and Underground Mining use.

- Manufactured in accordance with IEC Standards and tested in accordance & comply to Australia Standard AS2380.2 1991.

- Certified by SAA for Class 1 Zone 1and Gas Groups IIA & IIB T5 SAA Ex 1415

- Approved for used in Underground coal mines by NSW. Dept. Minerals & Energy and Qld.Dept. Mines.

Code Ex ‘e’ - Increased Safety motors - Certified by SAA for Class 1 Zone 1and Gas Groups IIA, IIB & IIC - T3 SAA Ex 1041X - AS2380 / AS1359

Code D.I.P. - Dust Ignition Proof motors - Certified by SAA for Class 11 Division 1&2 - T4 SAA Ex 959 - AS2236 1985

Code Ex ‘n - Non Sparking Motors - Certified by SAA for Class 1 Zone 2 and Gas Groups IIA, IIB & IIC - T4 SAA Ex 87 - AS2380.9 1991

Compliance to Standard

All motors suitable for use in Hazardous areas are manufacture/modified in strict accordance with the conditions required in the relevant Australian Standards & the issued certificate of Compliance and are fully tested before delivered by motor manufacturer.

More detail information on selection of motor for use in hazardous areas, zonal and temperature classification can be supplied upon requested.

Accessories - Anti-vibration spring mountings - Dampers - Cone inlets- Connection spigots - Cylindrical attenuators - Flexible Connectors - Guide vanes - Mounting feet - Mounting Plates- Wire guards

Catalogue, dimensions and detail information on specification and perform-ance are available upon requested.

5A09.BD V2011/November

LRK MFRSG-AXVGL-AXV

AXV 315-7, 50 Hz

Peak absorbed power PLmax [kW]

Volumenstrom / volume flow V. [m³/h]

[m³/s]

Relative frequency spectrum LWArel in ∆dB/Okt

Octave band mid-fr. [Hz] 63 125 250 500 1k 2k 4k 8k

n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32

Dimensions + Accessories page 34

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,01 0,01 0,01 0,01 0,01 0,01 0,01 0,02 0,02 0,02 0,02 0,02 0,02 0,37 0,02 0,03 0,03 0,03 0,03 0,04 0,04 0,05 0,06 0,06 0,07 0,07 0,08 0,37 0,18 0,21 0,26 0,24 0,26 0,28 0,32 0,4 0,47 0,49 0,53 0,54 0,61 0,37 0,55 0,75

645009, AXV-AL 315-7, 2880, 1440, 960

0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45

400 800 1200 1600

0.1 0.2 0.3 0.4 0.5 0.6

500 750 1000 1250 1500 1750 2000 2250

0.2 0.4 0.6 0.8 1 1.2

1000 1500 2000 2500 3000 3500 4000 4500

0

5

10

15

20

25

30

35

40

0

10

20

30

40

50

60

70

80

90

100

0

50

100

150

200

250

300

350

400

65

70

70

75

80

85

90

95

8°10°

12°14°

16°18°

20°

22°

24°

26°

28°

30°

32°

8°10°

12°

14°

16° 18°20°

22° 24°26°28°

30°32°

2880 1/min

1440 1/min

960 1/min

-7 -5 -7 -9 -10 -15 -21 -22

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18

960motor1440motor2880motor

6 A09.BD V2011/November

LRK MFRSG-AXVGL-AXV

AXV 355-7, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]


Volume flow V. [m³/h]

[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,01 0,01 0,02 0,02 0,02 0,02 0,02 0,03 0,03 0,03 0,04 0,04 0,04 0,37 0,04 0,05 0,06 0,06 0,06 0,06 0,07 0,09 0,11 0,11 0,12 0,12 0,14 0,37 0,32 0,38 0,47 0,44 0,48 0,51 0,59 0,74 0,85 0,9 0,97 0,99 1,11 0,37 0,55 0,75 0,9 1,1 1,5

645024, AXV-AL 355-7, 2880, 1440, 960

0.1 0.2 0.3 0.4 0.5 0.6 0.7

500 1000 1500 2000 2500

0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1

500 1000 1500 2000 2500 3000 3500

0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2

1000 2000 3000 4000 5000 6000 7000

0

10

20

30

40

50

0

20

40

60

80

100

0

50

100

150

200

250

300

350

400

450

65

70

70

75

80

85

90

95

8°10°

12°

14°

16°

18°20°

22°

24°

26°

28°

30°

32°

8° 10°12° 14° 16° 18°

20° 22° 24°26°

28° 30°

32°

2880 1/min

1440 1/min

960 1/min

-7 -5 -7 -9 -10 -15 -21 -22

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18



LRK MFRSG-AXVGL-AXV

AXV 400-7, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,02 0,02 0,02 0,02 0,03 0,03 0,03 0,04 0,04 0,05 0,05 0,06 0,06 0,37 0,05 0,06 0,07 0,09 0,10 0,12 0,12 0,13 0,16 0,16 0,19 0,21 0,22 0,37 0,42 0,48 0,56 0,68 0,81 0,92 0,95 1,06 1,24 1,30 1,49 1,68 1,79 0,55 0,75 1,1 1,5 2,2

645023, AXV-AL 400-7, 2880, 1440, 960

0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1

500 1500 2500 3500

0.2 0.4 0.6 0.8 1 1.2 1.4

1000 1500 2000 2500 3000 3500 4000 4500 5000

0.5 1 1.5 2 2.5 3

2000 3000 4000 5000 6000 7000 8000 9000 10000

0

10

20

30

40

50

60

0

20

40

60

80

100

120

140

0

100

200

300

400

500

600

65

70

75

75

80

85

90

95

100

8°10°

12°

14°16°

18°20°

22°

24°

26°

28°

30°

32°

8° 10°12° 14° 16° 18°

20° 22° 24°26°

28° 30°

32°

2880 1/min

1440 1/min

960 1/min

-5 -6 -5 -6 -7 -10 -15 -21

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18



LRK MFRSG-AXVGL-AXV

AXV 450-7, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,03 0,03 0,04 0,04 0,05 0,05 0,06 0,06 0,07 0,08 0,10 0,11 0,12 0,37 0,09 0,11 0,13 0,15 0,18 0,18 0,20 0,22 0,25 0,30 0,35 0,37 0,40 0,37 0,55 0,70 0,87 1,03 1,22 1,40 1,41 1,56 1,76 1,96 2,36 2,77 2,94 3,22 1,1 1,5 2,2 3,0 4,0

645003, AXV-AL 450-7, 2880, 1440, 960

0.2 0.4 0.6 0.8 1 1.2

1000 2000 3000 4000

0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2

1000 2000 3000 4000 5000 6000 7000

0.5 1 1.5 2 2.5 3 3.5 4

2000 4000 6000 8000 10000 12000 14000

0

10

20

30

40

50

60

70

80

0

20

40

60

80

100

120

140

160

180

0

100

200

300

400

500

600

700

70

75

80

75

80

85

90

90

95

100

105

8°10°

12°14°

16°18°

20°

22°

24°

26°28°

30°

32°

8° 10° 12° 14° 16°

18° 20° 22° 24° 26° 28° 30°32°

2880 1/min

1440 1/min

960 1/min

-3 -5 -7 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18



LRK MFRSG-AXVGL-AXV

AXV 500-7, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

* out of range

1440 4-pol

960 6-pol

2880 2-pol

0,04 0,05 0,06 0,07 0,09 0,09 0,09 0,11 0,12 0,14 0,17 0,18 0,20 0,37 0,15 0,18 0,22 0,26 0,30 0,30 0,33 0,37 0,42 0,50 0,59 0,62 0,68 0,37 0,55 0,75 1,19 1,47 1,74 2,06 2,37 2,39 2,63 2,98 3,32 3,99 1,5 2,2 3,0 4,0 -*

645004, AXV-AL 500-7, 2880, 1440, 960

0.4 0.6 0.8 1 1.2 1.4 1.6 1.8

1000 3000 5000

0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5 2.75

2000 3000 4000 5000 6000 7000 8000 9000 10000

1 1.5 2 2.5 3 3.5 4 4.5 5 5.5

4000 6000 8000 10000 12000 14000 16000 18000 20000

0

20

40

60

80

100

0

25

50

75

100

125

150

175

200

225

0

100

200

300

400

500

600

700

800

900

70

75

80

85

80

85

90

95

100

105

110

8°10°

12°14°

16°

18°

20°

22°

24°

26°28°

30°

32°

8° 10° 12° 14° 16°

18° 20° 22° 24° 26° 28° 30°32°

2880 1/min

1440 1/min

960 1/min

-3 -5 -7 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18



LRK MFRSG-AXVGL-AXV

AXV 560-9, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,10 0,12 0,14 0,16 0,18 0,21 0,23 0,26 0,29 0,31 0,33 0,38 0,41 0,37 0,55 0,36 0,42 0,50 0,55 0,64 0,72 0,79 0,89 1,01 1,06 1,13 1,32 1,45 0,55 0,75 1,1 1,5 2,87 3,38 3,99 4,43 5,08 5,77 6,32 7,13 8,04 8,50 9,07 10,6 11,6 3,0 4,0 5,5 7,5 11 15

-3 -5 -7 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18

645021, AXV-AL 560-9, 2880, 1440, 960

0.75 1 1.25 1.5 1.75 2 2.25 2.5

2000 4000 6000 8000

1 1.5 2 2.5 3 3.5 4

4000 6000 8000 10000 12000 14000

2 3 4 5 6 7 8

7500 10000 12500 15000 17500 20000 22500 25000 27500

0

20

40

60

80

100

120

140

0

50

100

150

200

250

300

0

200

400

600

800

1000

1200

80

85

85

90

95

100

105

110

8°10°

12°

14°

16°18°

20°

22°

24°

26°

28°

30°

32°

8° 10°

12°

14° 16° 18° 20° 22°

24° 26° 28° 30°32°

2880 1/min

1440 1/min

960 1/min



LRK MFRSG-AXVGL-AXV

AXV 560-6, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,07 0,09 0,10 0,12 0,15 0,16 0,18 0,20 0,22 0,24 0,27 0,29 0,31 0,37 0,25 0,31 0,35 0,42 0,53 0,57 0,64 0,70 0,76 0,85 0,96 1,02 1,08 0,55 0,75 1,1 2,04 2,46 2,76 3,39 4,21 4,58 5,14 5,59 6,06 6,78 7,65 8,19 8,67 2,2 3,0 4,0 5,5 7,5 11,0

645016, AXV-AL 560-6, 2880, 1440, 960

0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5

2000 4000 6000 8000

1 1.5 2 2.5 3 3.5

4000 6000 8000 10000 12000

2 3 4 5 6 7

5000 7500 10000 12500 15000 17500 20000 22500 25000

0

20

40

60

80

100

0

25

50

75

100

125

150

175

200

225

250

0

200

400

600

800

1000

80

85

85

90

95

100

105

110

8°10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12° 14° 16° 18° 20°

22° 24° 26°

28° 30°32°

2880 1/min

1440 1/min

960 1/min

-3 -5 -7 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18



LRK MFRSG-AXVGL-AXV

AXV 560-3, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,04 0,05 0,06 0,08 0,09 0,10 0,12 0,13 0,15 0,16 0,18 0,20 0,22 0,37 0,14 0,17 0,22 0,27 0,31 0,36 0,41 0,46 0,51 0,57 0,62 0,68 0,77 0,55 0,75 1,1 1,11 1,39 1,76 2,14 2,51 2,89 3,28 3,65 4,10 4,54 4,97 5,44 6,19 1,5 2,2 3,0 4,0 5,5 7,5

-3 -5 -7 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18

645025, AXV-AL 560-3, 2880, 1440, 960

0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2

2000 4000 6000 8000

0.5 1 1.5 2 2.5 3

2000 4000 6000 8000 10000 12000

1 2 3 4 5 6

5000 7500 10000 12500 15000 17500 20000 22500 25000

0

10

20

30

40

50

60

70

80

0

20

40

60

80

100

120

140

160

180

0

100

200

300

400

500

600

700

75

80

85

85

90

95

100

105

110

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10°

12° 14° 16°

18° 20° 22° 24° 26°

28° 30°

32°

2880 1/min

1440 1/min

960 1/min



LRK MFRSG-AXVGL-AXV

AXV 630-9, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

* out of range

1440 4-pol

960 6-pol

2880 2-pol

0,15 0,20 0,25 0,28 0,29 0,33 0,36 0,40 0,47 0,55 0,61 0,64 0,71 0,37 0,55 0,75 0,53 0,69 0,88 0,96 1,02 1,15 1,24 1,41 1,65 1,90 2,11 2,22 2,47 0,55 0,75 1,1 1,5 2,2 3,0 4,24 5,52 7,04 7,68 8,16 9,20 9,92 11,3 13,2 15,2 16,9 17,8 5,5 7,5 11,0 15,0 18,5 -*

-3 -5 -7 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

-5 -10 -7 -5 -7 -8 -12 -18

645002, AXV-AL 630-9, 2880, 1440, 960

0.5 1 1.5 2 2.5 3 3.5

2000 6000 10000 14000

1 2 3 4 5

4000 6000 8000 10000 12000 14000 16000 18000 20000

2 4 6 8 10

5000 10000 15000 20000 25000 30000 35000 40000

0

20

40

60

80

100

120

140

160

180

0

50

100

150

200

250

300

350

400

0

200

400

600

800

1000

1200

1400

1600

75

80

85

85

90

95

100

105

110

8°

10°12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10°12° 14°16° 18°

20° 22° 24°26°

28°30° 32°

2880 1/min

1440 1/min

960 1/min



LRK MFRSG-AXVGL-AXV

AXV 630-6, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,12 0,15 0,18 0,21 0,24 0,27 0,28 0,31 0,34 0,39 0,42 0,46 0,50 0,37 0,55 0,42 0,51 0,62 0,72 0,83 0,93 0,99 1,08 1,20 1,36 1,47 1,62 1,75 0,55 0,75 1,1 1,5 2,2 3,39 4,07 4,92 5,73 6,63 7,41 7,90 8,62 9,61 10,8 11,8 12,9 14,0 4,0 5,5 7,5 11,0 15,0

645010, AXV-AL 630-6, 2880, 1440, 960

1 1.5 2 2.5 3 3.5

4000 8000 12000

1 1.5 2 2.5 3 3.5 4 4.5 5 5.5

4000 6000 8000 10000 12000 14000 16000 18000 20000

2 3 4 5 6 7 8 9 10 11

10000 15000 20000 25000 30000 35000 40000

0

20

40

60

80

100

120

140

0

50

100

150

200

250

300

0

200

400

600

800

1000

1200

80

85

90

90

95

100

105

110

115

8°10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12°

14°16°

18° 20°

22° 24° 26°28°

30° 32°

2880 1/min

1440 1/min

960 1/min

-3 -5 -7 -7 -8 -12 -18 -24

-7 -3 -7 -7 -8 -12 -18 -24

-5 -10 -7 -5 -7 -8 -12 -18



LRK MFRSG-AXVGL-AXV

AXV 630-3, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

1440 4-pol

960 6-pol

2880 2-pol

0,08 0,08 0,10 0,11 0,13 0,15 0,17 0,18 0,21 0,24 0,29 0,34 0,39 0,37 0,55 0,26 0,28 0,33 0,37 0,44 0,51 0,58 0,64 0,74 0,85 1,01 1,18 1,37 0,55 0,75 1,1 1,5 2,10 2,21 2,66 2,97 3,50 4,06 4,60 5,10 5,93 6,80 8,07 9,42 10,9 2,2 3,0 4,0 5,5 7,5 11,0

-3 -5 -7 -7 -8 -12 -18 -24

-4 -7 -7 -7 -10 -15 -21 -27

-5 -6 -5 -6 -7 -10 -15 -21


645007, AXV-AL 630-3, 2880, 1440, 960

1 1.5 2 2.5 3

3000 5000 7000 9000 11000

1.5 2 2.5 3 3.5 4 4.5 5

4000 6000 8000 10000 12000 14000 16000 18000

3 4 5 6 7 8 9 10

10000 15000 20000 25000 30000 35000

0

10

20

30

40

50

60

70

80

90

0

25

50

75

100

125

150

175

200

0

100

200

300

400

500

600

700

800

80

85

90

90

95

105

110

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12°

14°

16°18° 20°

22° 24°

26°28°

30°32°

2880 1/min

1440 1/min

960 1/min


LRK MFRSG-AXVGL-AXV

AXV 710-9, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

0,14 0,16 0,19 0,2 0,22 0,26 0,3 0,33 0,35 0,41 0,48 0,5 0,54 0,37 0,55 0,34 0,38 0,45 0,48 0,53 0,62 0,71 0,78 0,84 0,96 1,13 1,19 1,28 0,37 0,55 0,75 1,1 1,5 1,19 1,34 1,55 1,68 1,86 2,17 2,48 2,70 2,93 3,35 3,95 4,16 4,46 1,5 2,2 3,0 4,0 5,5

-10 -7 -5 -7 -8 -12 -18 -24

-10 -7 -5 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -5 -21

645006, AXV-AL 710-9, 1440, 960, 720

1 1.5 2 2.5 3 3.5 4

2000 6000 10000 14000

1 1.5 2 2.5 3 3.5 4 4.5 5 5.5

4000 6000 8000 10000 12000 14000 16000 18000 20000

2 3 4 5 6 7 8

5000 10000 15000 20000 25000 30000

0

20

40

60

80

100

120

0

25

50

75

100

125

150

175

200

225

0

100

200

300

400

500

80

85

85

90

95

95

100

8°10°

12°14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12°14°16°

18°

20°22°

24° 26° 28°

30°32°

1440 1/min

960 1/min

720 1/min

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 710-6, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

0,08 0,1 0,13 0,15 0,18 0,21 0,24 0,25 0,28 0,3 0,33 0,35 0,38 0,37 0,55 0,20 0,24 0,30 0,35 0,43 0,50 0,56 0,60 0,66 0,71 0,78 0,84 0,89 0,37 0,55 0,75 1,1 0,71 0,84 1,03 1,21 1,50 1,73 1,94 2,10 2,30 2,49 2,71 2,92 3,10 0,75 1,1 1,5 2,2 3,0 4,0

645041, AXV-AL 710-6, 1440, 960, 720

1 1.5 2 2.5 3 3.5

4000 8000 12000

1.5 2 2.5 3 3.5 4 4.5 5

4000 6000 8000 10000 12000 14000 16000 18000

2 3 4 5 6 7

7500 10000 12500 15000 17500 20000 22500 25000 27500

0

10

20

30

40

50

60

70

80

90

100

0

20

40

60

80

100

120

140

160

0

50

100

150

200

250

300

350

400

80

85

85

90

95

95

100

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10°

12°14° 16° 18° 20° 22°

24°

26°

28° 30°

32°

1440 1/min

960 1/min

720 1/min

-6 -5 -6 -7 -10 -15 -21 -27

-6 -5 -6 -7 -10 -15 -21 -27

-7 -3 -7 -7 -8 -12 -18 -24

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 710-3, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

0,05 0,06 0,07 0,08 0,1 0,11 0,14 0,15 0,17 0,19 0,2 0,23 0,26 0,37 0,12 0,14 0,16 0,20 0,23 0,26 0,32 0,35 0,40 0,44 0,48 0,54 0,61 0,37 0,55 0,75 0,42 0,49 0,57 0,68 0,80 0,91 1,11 1,23 1,38 1,54 1,66 1,89 2,12 0,55 0,75 1,1 1,5 2,2

645042, AXV-AL 710-3, 1440, 960, 720

1 1.5 2 2.5 3 3.5

3000 5000 7000 9000 11000

1.5 2 2.5 3 3.5 4 4.5

4000 6000 8000 10000 12000 14000 16000

2 3 4 5 6 7

6000 8000 10000 12000 14000 16000 18000 20000 22000 24000

0

10

20

30

40

50

60

70

0

20

40

60

80

100

120

0

50

100

150

200

250

80

85

85

90

95

100

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°30°

32°

8° 10° 12°

14°

16°18°

20°

22°

24° 26° 28°

30°

32°

1440 1/min

960 1/min

720 1/min

-5 -7 -7 -8 -12 -18 -24 -30

-5 -7 -7 -8 -12 -18 -24 -30

-4 -7 -7 -7 -10 -15 -21 -27

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 800-9, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

0,26 0,3 0,34 0,37 0,41 0,48 0,55 0,59 0,65 0,73 0,87 0,92 0,98 0,37 0,55 0,75 0,9 1,1 0,62 0,70 0,81 0,88 0,97 1,13 1,29 1,41 1,52 1,75 2,06 2,17 2,32 0,75 1,1 1,5 2,2 3,0 2,16 2,44 2,81 3,05 3,37 3,95 4,51 4,91 5,31 6,08 7,18 7,56 8,09 2,2 3,0 4,0 5,5 7,5 11,0

-10 -7 -5 -7 -8 -12 -18 -24

-10 -7 -5 -7 -8 -12 -18 -24

-5 -6 -5 -6 -7 -10 -15 -21

645012, AXV-AL 800-9, 1440, 960, 720

1 2 3 4 5

4000 8000 12000 16000 20000

1 2 3 4 5 6 7

5000 10000 15000 20000 25000

2 4 6 8 10

5000 10000 15000 20000 25000 30000 35000 40000

0

20

40

60

80

100

120

140

160

0

50

100

150

200

250

0

100

200

300

400

500

600

80

85

90

90

95

95

100

105

8°10°

12°14°

16°

18°20°

22°

24°

26°

28°

30°

32°

8° 10° 12°14°16°

18°

20°22°

24° 26° 28°

30°32°

1440 1/min

960 1/min

720 1/min

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 800-6, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

645022, AXV-AL 800-6, 1440, 960, 720

1.5 2 2.5 3 3.5 4 4.5 5 5.5

4000 8000 12000 16000 20000

2 3 4 5 6 7

7500 10000 12500 15000 17500 20000 22500 25000

3 4 5 6 7 8 9 10 11

10000 15000 20000 25000 30000 35000 40000

0

20

40

60

80

100

120

0

25

50

75

100

125

150

175

200

0

100

200

300

400

500

80

85

90

90

95

95

100

105

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10°

12° 14° 16° 18° 20° 22°

24°

26°

28° 30°

32°

1440 1/min

960 1/min

720 1/min

0,16 0,19 0,23 0,27 0,33 0,38 0,43 0,46 0,51 0,55 0,59 0,64 0,68 0,37 0,55 0,75 0,37 0,44 0,54 0,63 0,78 0,90 1,01 1,09 1,20 1,30 1,41 1,52 1,61 0,55 0,75 1,1 1,5 2,2 1,29 1,53 1,88 2,20 2,73 3,13 3,52 3,81 4,19 4,52 4,91 5,31 5,62 1,5 2,2 3,0 4,0 5,5 7,5

-6 -5 -6 -7 -10 -15 -21 -27

-6 -5 -6 -7 -10 -15 -21 -27

-7 -3 -7 -7 -8 -12 -18 -24

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 800-3, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

0,09 0,11 0,13 0,15 0,18 0,2 0,24 0,27 0,3 0,34 0,37 0,42 0,47 0,37 0,55 0,22 0,25 0,30 0,36 0,42 0,47 0,58 0,64 0,72 0,80 0,88 0,99 1,11 0,55 0,75 1,1 0,77 0,88 1,04 1,24 1,45 1,65 2,02 2,24 2,51 2,79 3,05 3,43 3,86 1,1 1,5 2,2 3,0 4,0

-5 -7 -7 -8 -12 -18 -24 -30

-5 -7 -7 -8 -12 -18 -24 -30

-4 -7 -7 -7 -10 -15 -21 -27

720motor 960

motor1440motor

645043, AXV-AL 800-3, 1440, 960, 720

1.5 2 2.5 3 3.5 4 4.5 5

4000 8000 12000 16000

2 3 4 5 6

6000 8000 10000 12000 14000 16000 18000 20000 22000 24000

3 4 5 6 7 8 9 10

10000 15000 20000 25000 30000 35000

0

10

20

30

40

50

60

70

80

0

20

40

60

80

100

120

140

0

50

100

150

200

250

300

350

85

90

90

95

100

105

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12°

14°

16°18°

20°

22°

24° 26° 28°

30°

32°

1440 1/min

960 1/min

720 1/min

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 900-10, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

0,4 0,48 0,55 0,67 0,77 0,88 0,99 1,12 1,22 1,4 1,59 1,69 1,78 0,55 0,75 0,9 1,1 1,5 2,2 0,95 1,13 1,30 1,59 1,83 2,08 2,35 2,65 2,89 3,32 3,78 3,96 4,21 1,1 1,5 2,2 3,0 4,0 5,5 3,30 3,94 4,54 5,54 6,39 7,26 8,19 9,24 10,1 11,6 13,2 13,8 14,7 4,0 5,5 7,5 11,0 15,0

-10 -7 -5 -7 -8 -12 -18 -24

-10 -7 -5 -7 -8 -12 -18 -24

-10 -12 -6 -5 -7 -10 -15 -21

645011, AXV-AL 900-10, 1440, 960, 720

2 3 4 5 6 7 8

5000 15000 25000

2 4 6 8 10

10000 15000 20000 25000 30000 35000 40000

4 6 8 10 12 14 16

10000 20000 30000 40000 50000 60000

0

25

50

75

100

125

150

175

200

0

50

100

150

200

250

300

350

0

100

200

300

400

500

600

700

800

85

90

95

90

95

100

100

105

110

8°

10°12°

14°

16°

18°20°

22°

24°

26°

28°

30°

32°

8° 10°

12° 14° 16°

18° 20° 22°

24° 26°28°30°

32°

1440 1/min

960 1/min

720 1/min

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 900-5, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

0,22 0,27 0,33 0,4 0,46 0,55 0,61 0,67 0,74 0,82 0,88 1,05 1,19 0,37 0,55 0,75 0,9 1,1 1,5 0,52 0,63 0,79 0,95 1,08 1,30 1,44 1,59 1,76 1,93 2,09 2,49 2,81 0,55 0,75 1,1 1,5 2,2 3,0 1,82 2,20 2,76 3,30 3,76 4,54 5,01 5,52 6,13 6,73 7,28 8,68 9,80 2,2 3,0 4,0 5,5 7,5 11,0

-6 -5 -6 -7 -10 -15 -21 -27

-6 -5 -6 -7 -10 -15 -21 -27

-10 -7 -5 -7 -8 -12 -18 -24

720motor 960

motor1440motor

645005, AXV-AL 900-5, 1440, 960, 720

1 2 3 4 5 6 7 8

5000 15000 25000

2 3 4 5 6 7 8 9 10

5000 10000 15000 20000 25000 30000 35000

2 4 6 8 10 12 14 16

10000 20000 30000 40000 50000

0

20

40

60

80

100

120

140

0

50

100

150

200

250

0

100

200

300

400

500

600

85

90

90

95

100

100

105

110

8°10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12°14°

16° 18° 20° 22° 24° 26°

28° 30° 32°

1440 1/min

960 1/min

720 1/min

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 1000-10, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

* Motor protrudes the fan housing

0,68 0,81 0,93 1,13 1,31 1,49 1,68 1,89 2,07 2,37 2,7 2,86 3 0,75 0,9 1,1 1,5 2,2 3 1,60 1,92 2,21 2,69 3,11 3,53 3,98 4,78 4,90 5,62 6,41 6,78 7,12 2,2 3,0 4,0 5,5 7,5 5,58 6,67 7,69 9,37 10,8 12,3 13,9 16,7 17,1 19,6 22,3 23,6 24,8 7,5 11,0 15,0 18,5 22,0 30*

-10 -7 -5 -7 -8 -12 -18 -24

-10 -7 -5 -7 -8 -12 -18 -24

-10 -12 -6 -5 -7 -10 -15 -21

645000, AXV-AL 1000-10, 1440, 960, 720

2 4 6 8 10 12

10000 20000 30000 40000

4 6 8 10 12 14 16

10000 20000 30000 40000 50000

5 7.5 10 12.5 15 17.5 20 22.5

20000 30000 40000 50000 60000 70000 80000

0

50

100

150

200

250

0

50

100

150

200

250

300

350

400

450

0

200

400

600

800

1000

85

90

95

100

95

100

105

100

105

110

115

8°

10°12°

14°

16°

18°20°

22°

24°

26°

28°

30°

32°

8° 10°

12° 14° 16°

18° 20° 22°

24° 26°28°30°

32°

1440 1/min

960 1/min

720 1/min

720motor 960

motor1440motor

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 1000-5, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

0,38 0,45 0,57 0,68 0,77 0,93 1,03 1,13 1,26 1,38 1,49 1,78 2,01 0,55 0,75 0,9 1,1 1,5 2,2 0,89 1,07 1,34 1,60 1,83 2,21 2,43 2,69 2,98 3,27 3,54 4,22 4,77 1,1 1,5 2,2 3,0 4,0 5,5 3,09 3,73 4,68 5,59 6,37 7,69 8,48 9,35 10,4 11,4 12,3 14,7 16,6 4,0 5,5 7,5 11,0 15,0 18,5

-6 -5 -6 -7 -10 -15 -21 -27

-6 -5 -6 -7 -10 -15 -21 -27

-10 -7 -5 -7 -8 -12 -18 -24

720motor 960

motor1440motor

645049, AXV-AL 1000-5, 1440, 960, 720

2 3 4 5 6 7 8 9 10

5000 15000 25000 35000

2 4 6 8 10 12 14

10000 15000 20000 25000 30000 35000 40000 45000 50000

4 6 8 10 12 14 16 18 20

10000 20000 30000 40000 50000 60000 70000

0

20

40

60

80

100

120

140

160

180

0

50

100

150

200

250

300

0

100

200

300

400

500

600

700

85

90

95

95

100

100

105

110

8°10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8° 10° 12°14°

16° 18° 20° 22° 24° 26°

28° 30° 32°

1440 1/min

960 1/min

720 1/min

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 1120-12, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]

1,08 1,27 1,45 1,61 1,83 2,13 2,41 2,81 2,9 3,37 3,67 4,08 4,72 1,1 1,5 2,2 3 4 5,5 2,47 2,91 3,33 3,69 4,19 4,9 5,53 6,45 6,66 7,73 8,43 9,38 10,8 3 4 5,5 7,5 11 8,62 10,1 11,6 12,8 14,6 17,1 19,3 22,5 23,2 26,9 29,3 32,7 37,8 11 15 18,5 22 30 37 45

-3 -7 -7 -10 -14 -18 -24 -30

-6 -5 -6 -7 -10 -15 -21 -27

-5 -5 -6 -7 -9 -13 -18 -24

720motor960

motor1440motor

645195, AXV-AL 1120-14, 1440, 960, 720

2 4 6 8 10 12 14

10000 20000 30000 40000 50000

4 6 8 10 12 14 16 18 20

10000 20000 30000 40000 50000 60000 70000

5 10 15 20 25 30

20000 30000 40000 50000 60000 70000 80000 90000 100000

0

50

100

150

200

250

300

0

100

200

300

400

500

0

200

400

600

800

1000

1200

100

105

105

110

115

120

8°10°

12°14°

16°

18°

20°22°

24°

26°

28°

30°

32°

8°10°12°

14°16°

18° 20°22°24°26°

28°30° 32°

1440 1/min

960 1/min

720 1/min

1440 4-pol

960 6-pol

720 8-pol


LRK MFRSG-AXVGL-AXV

AXV 1120-6, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]

0,62 0,77 1,00 1,07 1,20 1,41 1,61 1,90 2,13 2,50 2,60 2,78 3,23 1,1 1,5 2,2 3 4 1,48 1,83 2,36 2,54 2,85 3,31 3,81 4,49 5,05 5,92 6,17 6,60 7,66 2,2 3 4 5,5 7,5 4,98 6,19 7,98 8,56 9,61 11,2 12,9 15,2 17,0 20,0 20,8 22,3 25,9 5,5 7,5 11 15 18,5 22 30

720motor960

motor1440motor

-3 -7 -7 -8 -12 -18 -24 -30

-6 -5 -6 -7 -10 -15 -21 -27

-5 -5 -6 -7 -8 -12 -18 -24

1440 4-pol

960 6-pol

720 8-pol

119WX1 V.�008/9

!"

LRK MFWGGL-AXV

AXV 1120-7, 50 HzG

esam

t-Sch

allle

istu

ngsp

egel

LW [d

B]

soun

d po

wer

leve

lTo

tald

ruck

Dp t [

PA]

tota

l pre

ssur

e

max. Aufnahmeleistung PLmaxpeak absorbed power [kW]


[m³/s] Relative Frequenzspektren relative frequency spectrum LWArel in ∆dB/OktOktavb.-Mittenfr. / Octave band mid-fr. [Hz]

63 125 250 500 1k 2k 4k 8k n

[min-1]Flügelwinkel / pitch angle [°]

8 10 12 14 16 18 20 22 24 26 28 30 32

Abmessungen + Zubehör Seite / Dimensions + Accessories page 157-159, 176-179

Ausführung für Entrauchungsbetrieb 400°C/120min auf Anfrage. Smoke-extract version for 400°C/120min on request.

Bezugs- drehzahl

[min-1]

645196, AXV-AL 1120-7re, 1440, 960, 720

2 4 6 8 10 12 14

5000 15000 25000 35000 45000

2 4 6 8 10 12 14 16 18 20

10000 20000 30000 40000 50000 60000 70000

5 10 15 20 25 30

20000 40000 60000 80000 100000

0

25

50

75

100

125

150

175

200

225

250

0

50

100

150

200

250

300

350

400

0

200

400

600

800

1000

95

100

105

110

110

115

120

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

1440 1/min

960 1/min

720 1/min

1��0 �-pol

960 6-pol

7�0 8-pol

-� -7 -7 -8 -1� -18 -�� -�0

-6 -5 -6 -7 -10 -15 -�1 -�7

-5 -5 -6 -7 -8 -1� -18 -��

7�0motor960

motor1��0motor

0,6� 0,77 1 1,07 1,� 1,� 1,61 1,9 �,1� �,5 �,6 �,78 �,�� 0,75 0,9 1,1 1,5 �,� � � 1,�8 1,8� �,�6 �,5� �,85 �,�1 �,81 �,�9 5,05 5,9� 6,17 6,6 7,66 1,5 �,� � � 5,5 7,5 11 �,98 6,19 7,98 8,56 9,61 11,� 1�,9 15,� 17 �0 �0,8 ��,� �5,9 5,5 7,5 11 15 18,5 �� 0

3.1

645196, AXV-AL 1120-6 re, 1440, 960, 720


LRK MFRSG-AXVGL-AXV

AXV 1250-12, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]


1,94 2,28 2,61 2,9 3,29 3,87 4,38 5,1 5,28 6,12 6,68 7,45 8,63 3 4 5,5 7,5 11 4,46 5,25 6 6,65 7,56 8,89 10,1 11,7 12,1 14,1 15,4 17,1 19,8 5,5 7,5 11 15 18,5 22 15,5 18,3 20,9 23,2 26,3 31 35 40,8 42,2 49 53,5 59,6 69 18,5 22 30 37 45 55 75

-6 -5 -6 -7 -10 -15 -21 -27

-10 -7 -5 -7 -8 -12 -18 -24

-10 -12 -6 -5 -7 -10 -15 -21

720motor950

motor1440motor

645057, AXV-AL 1250-14, 1440, 960, 720

4 6 8 10 12 14 16 18 20

10000 30000 50000 70000

5 10 15 20 25

20000 30000 40000 50000 60000 70000 80000 90000 100000

10 15 20 25 30 35 40

20000 40000 60000 80000 100000 120000 140000

0

50

100

150

200

250

300

350

400

0

100

200

300

400

500

600

700

0

200

400

600

800

1000

1200

1400

1600

100

105

110

115

115

120

8°10°

12°14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°10°

12°14°

16°18° 20°22°24°

26°28°

30° 32°

1440 1/min

960 1/min

720 1/min

1440 4-pol

950 6-pol

720 8-pol

645057, AXV-AL 1250-12 re, 1440, 960, 720


LRK MFRSG-AXVGL-AXV

AXV 1250-6, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]


1,13 1,40 1,80 1,94 2,18 2,54 2,93 3,46 3,88 4,55 4,78 5,01 5,98 2,2 3 4 5,5 7,5 2,67 3,32 4,28 4,60 5,18 6,01 6,94 8,20 9,20 10,8 11,3 12,1 14,2 3 4 5,5 7,5 11 15 9,01 11,2 14,4 15,5 17,5 20,3 23,4 27,7 31,0 36,4 38,2 40,8 47,8 11 15 18,5 22 30 37 45 55

720motor960

motor1440motor

-3 -7 -7 -10 -14 -18 -24 -30

-6 -5 -6 -7 -10 -15 -21 -27

-5 -5 -6 -7 -9 -13 -18 -24

1440 4-pol

960 6-pol

720 8-pol

1�1WX1 V.�008/9

!"

LRK MFWGGL-AXV

AXV 1250-7, 50 HzG

esam

t-Sch

allle

istu

ngsp

egel

LW [d

B]

soun

d po

wer

leve

lTo

tald

ruck

Dp t [

PA]

tota

l pre

ssur

e




63 125 250 500 1k 2k 4k 8k n


8 10 12 14 16 18 20 22 24 26 28 30 32


Ausführung für Entrauchungsbetrieb 400°C/120min auf Anfrage. Smoke-extract version for 400°C/120min on request.

Bezugs- drehzahl

[min-1]

* Motor ragt aus Ventilator-Gehäuse / motor protrudes the fan housing

-� -7 -7 -10 -1� -18 -�� -�0

-6 -5 -6 -7 -10 -15 -�1 -�7

-5 -5 -6 -7 -9 -1� -18 -��

645100, AXV-AL 1250-7 re, 1440, 960, 720

2 4 6 8 10 12 14 16 18 20

10000 30000 50000 70000

5 10 15 20 25

10000 20000 30000 40000 50000 60000 70000 80000 90000 100000

5 10 15 20 25 30 35 40

20000 40000 60000 80000 100000 120000 140000

0

50

100

150

200

250

300

0

100

200

300

400

500

0

200

400

600

800

1000

1200

100

105

105

110

115

120

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

1440 1/min

960 1/min

720 1/min

1��0 �-pol

960 6-pol

7�0 8-pol

7�0motor960

motor1��0motor

1,1� 1,� 1,8 1,9� �,18 �,5� �,9� �,�6 �,88 �,55 �,78 5,1 5,98 �,� � � 5,5 7,5 �,67 �,�� ,�8 �,6 5,18 6,01 6,9� 8,� 9,� 10,8 11,� 1�,1 1�,� � � 5,5 7,5 11 15 9,01 11,� 1�,� 15,5 17,5 �0,� ��,� �7,7 �1 �6,� �8,� �0,8 �7,8 11 15 18,5 �� 0 �7 �5 55

3.1

645100, AXV-AL 1250-6 re, 1440, 960, 720


LRK MFRSG-AXVGL-AXV

AXV 1400-12, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]


1,96 2,33 2,59 2,92 3,18 3,67 4,26 4,71 5,39 5,96 6,6 7,08 7,92 2,2 3 4 5,5 7,5 11 3,82 4,54 5,06 5,68 6,22 7,16 8,31 9,2 10,6 11,6 12,9 13,8 15,5 4 5,5 7,5 11 15 18,5 9,06 10,8 12 13,5 14,7 17 19,7 21,8 25 27,6 30,6 32,8 36,6 11 15 18,5 22 30 37

-4 -5 -10 -13 -14 -17 -23 -25

-6 -4 -10 -13 -14 -16 -22 -24

-6 -3 -11 -13 -13 -14 -20 -24

576motor720

motor960

motor

645193,AXV-AL1400-14,960,720,576

5 7.5 10 12.5 15 17.5 20 22.5

10000 30000 50000 70000

5 10 15 20 25 30

20000 30000 40000 50000 60000 70000 80000 90000 100000 110000

5 10 15 20 25 30 35 40

20000 40000 60000 80000 100000 120000 140000

0

50

100

150

200

250

300

0

100

200

300

400

500

0

100

200

300

400

500

600

700

800

900

100

105

105

110

110

115

8°10°

12°14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°10°12°

14°16°

18° 20°22°24°26°28°

30° 32°

960 1/min

720 1/min

576 1/min

960 6-pol

720 8-pol

576 10-pol

645193, AXV-AL 1400-12 re, 960, 720, 576


LRK MFRSG-AXVGL-AXV

AXV 1400-6, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]


1,02 1,26 1,63 1,75 1,97 2,29 2,64 3,12 3,50 4,11 4,31 4,60 5,40 2,2 3 4 5,5 1,99 2,47 3,18 3,42 3,85 4,47 5,16 6,09 6,84 8,02 8,42 8,99 10,5 2,2 3 4 5,5 7,5 11 4,71 5,85 7,53 8,11 9,13 10,6 12,2 14,4 16,2 19,0 20,0 21,3 25 5,5 7,5 11 15 18,5 22 30

-5 -7 -7 -10 -15 -19 -24 -26

-5 -7 -7 -10 -15 -18 -23 -26

-5 -6 -8 -10 -14 -16 -21 -24

576motor720

motor960

motor

960 6-pol

720 8-pol

576 10-pol

1��WX1 V.�008/9

!"

LRK MFWGGL-AXV

AXV 1400-7, 50 HzG

esam

t-Sch

allle

istu

ngsp

egel

LW [d

B]

soun

d po

wer

leve

lTo

tald

ruck

Dp t [

PA]

tota

l pre

ssur

e




63 125 250 500 1k 2k 4k 8k n


8 10 12 14 16 18 20 22 24 26 28 30 32


Bezugs- drehzahl

[min-1]


-5 -7 -7 -10 -15 -19 -�� -�6

-5 -7 -7 -10 -15 -18 -�� -�6

-5 -6 -8 -10 -1� -16 -�1 -��

645194, AXV-AL 1400-7 re, 960, 720, 576

2.5 5 7.5 10 12.5 15 17.5 20 22.5

10000 30000 50000 70000

5 10 15 20 25 30

20000 40000 60000 80000 100000

5 10 15 20 25 30 35 40

20000 40000 60000 80000 100000 120000 140000

0

50

100

150

200

250

0

50

100

150

200

250

300

350

0

100

200

300

400

500

600

700

100

105

105

110

110

115

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°

10°

12°

14°

16°

18° 20°

22°

24°

26°

28°

30°

32°

960 1/min

720 1/min

576 1/min

960 6-pol

7�0 8-pol

576 10-pol

576motor7�0

motor960

motor

1,0� 1,�6 1,6� 1,75 1,97 �,�9 �,6� �,1� �,5 �,11 �,�1 �,6 5,� �,� � � 5,5 1,99 �,�7 �,18 �,�� ,85 �,�7 5,16 6,09 6,8� 8,0� 8,�� 8,99 10,5 �,� � � 5,5 7,5 11 �,71 5,85 7,5� 8,11 9,1� 10,6 1�,� 1�,� 16,� 19 �0 �1,� �5 5,5 7,5 11 15 18,5 �� 0

3.1

645194, AXV-AL 1400-6 re, 960, 720, 576


LRK MFRSG-AXVGL-AXV

AXV 1600-12, 50 Hz

Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


!"PerformanceCurve

Speed [min-1]


3,49 4,1 4,69 5,2 5,91 6,95 7,86 9,16 9,48 11 12 13,4 15,5 4 5,5 7,5 11 15 18,5 6,67 7,85 8,97 9,95 11,3 13,3 15 17,5 18,1 21 23 25,6 29,6 7,5 11 15 18,5 22 30 15,3 18 20,6 22,9 26 30,6 34,5 40,2 41,6 48,3 52,7 58,8 68,1 18,5 22 30 37 45 55 75

-4 -5 -10 -13 -14 -17 -23 -25

-6 -4 -10 -13 -14 -16 -22 -24

-6 -3 -11 -13 -13 -14 -20 -24

576motor720

motor950

motor

645202, AXV-AL 1600-14, 960, 720, 576

5 10 15 20 25 30 35

20000 60000 100000

10 15 20 25 30 35 40 45

40000 60000 80000 100000 120000 140000 160000

10 20 30 40 50 60

40000 60000 80000 100000 120000 140000 160000 180000 200000

0

50

100

150

200

250

300

350

400

0

100

200

300

400

500

600

0

200

400

600

800

1000

105

110

110

115

115

120

8°10°

12°14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°10°12°

14°16°

18° 20°22°24°26°

28°30° 32°

960 1/min

720 1/min

576 1/min

950 6-pol

720 8-pol

576 10-pol

645202, AXV-AL 1600-12 re, 960, 720, 576


LRK MFRSG-AXVGL-AXV

AXV 1600-6, 50 Hz



[m³/s]



n[min-1]

Pitch angle [°] 8 10 12 14 16 18 20 22 24 26 28 30 32


Sou

nd p

ower

leve

l LW [d

B]

Tota

l pre

ssur

e ∆

p t [PA

]

!"PerformanceCurve

Speed [min-1]


1,92 2,39 3,08 3,31 3,72 4,32 4,99 5,89 6,62 7,75 8,14 8,70 10,2 2,2 3 4 5,5 7,5 11 3,75 4,66 6,01 6,47 7,27 8,45 9,75 11,5 12,9 15,1 15,9 17,0 19,9 4 5,5 7,5 11 15 18,5 22 8,89 11 14,2 15,3 17,2 20,0 23,1 27,3 30,6 35,9 37,7 40,3 47,2 11 15 18,5 22 30 37 45 55

-5 -7 -7 -10 -15 -19 -24 -26

-5 -7 -7 -10 -15 -18 -23 -26

-5 -6 -8 -10 -14 -16 -21 -24

576motor720

motor960

motor

1�5WX1 V.�008/9

!"

LRK MFWGGL-AXV

AXV 1600-7, 50 HzG

esam

t-Sch

allle

istu

ngsp

egel

LW [d

B]

soun

d po

wer

leve

lTo

tald

ruck

Dp t [

PA]

tota

l pre

ssur

e




63 125 250 500 1k 2k 4k 8k n


8 10 12 14 16 18 20 22 24 26 28 30 32


Bezugs- drehzahl

[min-1]


-5 -7 -7 -10 -15 -19 -�� -�6

-5 -7 -7 -10 -15 -18 -�� -�6

-5 -6 -8 -10 -1� -16 -�1 -��

645203, AXV-AL 1600-7re, 960, 720, 576

5 10 15 20 25 30 35

20000 60000 100000

5 10 15 20 25 30 35 40

20000 40000 60000 80000 100000 120000 140000 160000

10 20 30 40 50

25000 50000 75000 100000 125000 150000 175000 200000

0

50

100

150

200

250

300

0

100

200

300

400

500

0

100

200

300

400

500

600

700

800

900

100

105

110

105

110

115

115

120

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

8°

10°

12°

14°

16°

18°

20°

22°

24°

26°

28°

30°

32°

960 1/min

720 1/min

576 1/min

950 6-pol

7�0 8-pol

576 10-pol

576motor7�0

motor960

motor

1,9� �,�9 �,08 �,�1 �,7� �,�� ,99 5,89 6,6� 7,75 8,1� 8,7 10,� �,� � � 5,5 7,5 11 �,75 �,66 6,01 6,�7 7,�7 8,�5 9,75 11,5 1�,9 15,1 15,9 17 19,9 � 5,5 7,5 11 15 18,5 �� 8,89 11 1�,� 15,� 17,� �0 ��,1 �7,� �0,6 �5,9 �7,7 �0,� �7,� 11 15 18,5 �� 0 �7 �5 55

3.1

960 6-pol

720 8-pol

576 10-pol

645203, AXV-AL 1600-6 re, 960, 720, 576


AXVAxial Flow FansBelt Driven

Dimensions

LH/1 LH/2Model s k1 l1 motor s k1 l1 motor DDa Ld Lk Usize [mm] [mm] [mm] max. [mm] [mm] [mm] max. [mm] [mm] [mm] [mm]

315 2 356 420 80 426 165 250 -355 2 356 420 80 435 165 250 -400 2 371 435 90 507 165 250 -450 2 371 435 112 555 165 250 15500 2 396 470 112 617 165 250 45560 2 396 470 112 3 624 700 160 667 165 250 80630 2 396 470 112 3 624 700 160 757 165 250 120710 2,5 395 470 112 2,5 490 565 132 816 170 350 60800 2,5 385 470 112 3 614 700 160 915 250 350 110900 3 479 565 132 4 612 700 160 1015 250 350 170

1000 3 479 565 132 4 692 780 180 1115 250 350 2251120 4 592 700 160 4 892 1000 200 1243 250 350 2551250 4 592 700 160 4 892 1000 225 1364 250 400 3751400 4 892 1000 225 1523 250 400 4501600 4 892 1000 280 1723 250 400 550

Model Da Di hF hF2 (max) z x d Tk E F bFsize [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]

315 398 320 205 700 8 x 10 366 265 315 60355 438 359 225 750 8 x 10 405 305 355 60400 484 401 250 810 12 x 10 448 350 400 60450 534 450 280 860 12 x 10 497 400 450 60500 584 504 315 1041 12 x 10 551 440 500 70560 664 565 345 1094 16 x 12 629 500 560 70630 734 634 400 1246 16 x 12 698 570 630 70710 814 711 450 1454 16 x 12 775 650 710 70800 904 797 500 1544 12* x 12 861 730 800 80900 1004 894 580 1746 12* x 12 958 830 900 80

1000 1105 1003 630 1821 12* x 12 1067 930 990 801120 1245 1125 690 1990 12* x 12 1200 1050 1110 1001250 1370 1250 750 2175 12* x 12 1337 1180 1240 1001400 1525 1405 830 2362 16* x 14 1475 1330 1390 1001600 1725 1605 930 2550 16* x 14 1675 1530 1590 100

DaTk

30

ULk

Optional Standard Guide Vane

Optional Connecting Flange

E

F

hF

hF2

Optional Mounting Feet

Z nos. x d

Optional Inlet Cone

Di

K1

I1

DDa

Ld

bF

* Subject to alteration reserved.

Agents.

Wolter GmbHMaschinen- und Apparatebau KG

Am Wasen 11D-76316 MalschTel. +49 (0) 72 04 / 92 01 0 Fax +49 (0) 72 04 / 92 01 11www.wolter.eu [email protected]

Germany Burkhardt Projekt GmbHD-67583 GuntersblumT +49 (0) 62 49 / 82 01F +49 (0) 62 49 / 88 [email protected]

Industrieservice Drexler D-49080 OsnabrückT +49 (0) 541 / 20 04 88 3F +49 (0) 541 / 20 04 88 [email protected]

Friedrich GlockD-97980 Bad MergentheimT +49 (0) 79 31 / 37 44F +49 (0) 79 31 / 28 [email protected]

Mattias IndustrievertretungenD-16259 Bad FreienwaldeT +49 (0) 33 44 / 30 19 94F +49 (0) 33 44 / 30 19 [email protected]

Ing. Günther RößlerD-07619 SchkölenT +49 (0) 36 69 4 / 22 359F +49 (0) 36 69 4 / 22 [email protected]

EuropeDanmark:

Air-Con Danmark A/SDK-8400 EbeltoftT +45 (0) 86 / 34 51 11F +45 (0) 86 / 34 58 [email protected]

Greece:

Clima Comfort Components LtdGR-115 28 AthensT +30 (0) 210 / 72 55 92 56F +30 (0) 210 / 72 55 [email protected]

Hungary:

Air-Technik Légtechnikai Kft.HU-2040 BudaörsT +36 (0) 23 / 42 85 33F +36 (0) 23 / 42 85 [email protected]

Netherlands:

AirFan B. V.NL-7442 CX NijverdalT +31 (0) 548 / 36 63 66F +31 (0) 548 / 36 53 [email protected]

Austria:

Wolter Werksvertretung ÖsterreichA-4040 LinzT +43 (0) 732 / 75 77 07F +43 (0) 732 / 75 77 07 [email protected]

Poland:

Wentoprodukt44-100 GliwiceT +48 (32) 331 / 34 24F +48 (32) 729 / 76 [email protected]

Portugal:

Safe Park Ventilação Industrial Lda.P-2675-240 OdivelasT +351 (21) 93 / 75 265F +351 (21) 93 / 86 [email protected]

Russia:

Euroclimat LtdRU-105082 MoskauT +7 (0) 499 / 75 30 355F +7 (0) 499 / 78 87 [email protected]

Switzerland:

Anson AG ZürichCH-8055 ZürichT +41 (0) 44 / 46 11 111F +41 (0) 44 / 46 13 [email protected]

Ventra Technik AGCH-8599 SalmsachT +41 (0) 71 / 46 11 447F +41 (0) 71 / 46 11 [email protected]

Turkey:

Air Trade Centre Ltd Sti Türkiye,TR-34418 Seyrantepe / InstanbulT +90 (0) 212 / 28 34 510F +90 (0) 212 / 27 83 [email protected]

United Kingdom:

Wolter (UK) LtdGB-B37 7UQ SolihullT +44 (0) 121 / 63 55 390F +44 (0) 121 / 63 55 [email protected]

Middle East and North Africa

Israel:

Pach Taas (Ashkelon) LtdIL-78100 AshkelonT +972 (0) 8 / 67 19 770F +972 (0) 8 / 67 19 [email protected]

UAE, Qatar, Lebanon, Jordan, Saudi Arabia

Energy International Co.UAE-Sharjah, P.O. Box 3562T +971 (0) 6 / 53 43 477F +971 (0) 6 / 53 43 [email protected]

Asia and AustraliaChina Mainland:

Dongguan Wolter Chemco Ventilation LtdCHN-Dongguan City, GuangdongT +86(0) 769 / 86 55 72 98F +86 (0) 769 / 86 55 72 [email protected]

Taizhou Wolter Ventilator Co., LtdCHN- Taizhou City, Luqiao District, ZhejiangT +86 (0) 769 / 86 55 72 98F +86 (0) 769 / 86 55 72 [email protected]

Hongkong:

Wolter Asia LtdTuen Mun, N.T.T +852 (0) 24 / 56 01 98F +852 (0) 24 / 56 02 [email protected]

India:

Wolter Ventilators India Pvt. LtdIND-301019 Bhiwadi District Alwar, RajasthanT +91 (0) 124 / 25 77 797F +91 (0) 124 / 25 77 [email protected]

Indonesia:

Pt. Sinarbaskara TriutamaID-10440 Jakarta IndonesiaT +62 (0) 21 / 31 00 191F +62 (0) 21 / 39 12 [email protected]

Korea:

Kaceco-WolterKR-435-010 Gunpo-Shi, Kyonggi-do, Gyeonggi-doT +82 (0) 31 / 47 73 104F +82 (0) 31 / 47 73 [email protected]

Singapore:

Wolter Pte. LtdSG-569738 SingaporeT +65 (0) 63 / 52 95 48F +65 (0) 63 / 52 95 [email protected]

Malaysia:

Vibran Marketing Sdn. Bhd.MAL-47200 Subang, Selangor Darul EhsanT +603 (0) 78 47 / 35 00F +603 (0) 78 47 / 35 [email protected]

Thailand:

Wolter Ventilation Co., LtdTH-74130 SamutsakornT +66 (0) 2 / 81 38 484F +66 (0) 2 / 81 18 [email protected]

Australia:

The Sydney Fan CompanyAU-2147 Seven Hills, NSWT +61 (0) 2 / 96 24 40 00F +61 (0) 2 / 96 24 41 [email protected]

#

Documents

A09€¦ · A09.BD V.2011/November 1 ... pulleys, projecting set screws, keys and other ... WOLTER Belt driven axial flow fan motors are squirrel-cage induction