Double Tray Wall MountSingle Tray Wall Mount

*Load ratings are working loads with 3:1 Safety Factor** abP certificate is available on product webpage at www.nVent.com or your nVent customer service representattive for fire rated applications

Load Ratings*Configurations**

Part No. Threaded Rod Wall Mount nVent CADDY Speed Link Y-Hook

UTS150 100 lbs / 445 N 200 lbs / 890 N 200 lbs / 890 N UTS200 100 lbs / 445 N 200 lbs / 890 N 200 lbs / 890 N UTS300 100 lbs / 445 N 200 lbs / 890 N 200 lbs / 890 N

Part No. Article No. DescriptionUTS150 182031 Universal Tray Support 6 inch / 150mm C-BracketUTS200 182032 Universal Tray Support 8 inch / 200mm C-BracketUTS300 182033 Universal Tray Support 12 inch / 300mm C-Bracket

TECHNICAL SUPPORT:www.nVent.com CFS546_C

INSTRUCTION SHEET

1 OF 4 © 2017, 2018 nVent All Rights Reserved

UTS SERIES - UNIVERSAL TRAY SUPPORT

WARNING:nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at 1.www.nVent.com and from your nVent customer service representative. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.2.All instructions must be completely followed to ensure proper and safe installation and performance. 3.Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property 4.damage, serious bodily injury and/or death, and void your warranty.Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 5.All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any 6.other purpose.

NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.

The customer is responsible for:a. Conformance to all governing codes.b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.c. Using appropriate industry standard hardware as noted above.

SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

nVent, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.

2 Tray, Dual Brackets, Single Threaded Rod

4 Tray, Dual Brackets, Single Threaded Rod3 Tray, Dual Brackets, Single Threaded RodNote: Cover threaded rod to protect cables from being damaged by threads

Center Hung Threaded Rod with Nuts/Washers

Dual Bracket Fastening2 x M8 or 5/16" nuts & bolts

TECHNICAL SUPPORT:www.nVent.com CFS546_C

INSTRUCTION SHEET

2 OF 4 © 2017, 2018 nVent All Rights Reserved

UTS SERIES - UNIVERSAL TRAY SUPPORT

nVent, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.

Offset Threaded Rod with nVent CADDY Rod Lock

Ceiling Mount - Bend top tab to mount flush to ceiling

Wire Basket Cable Tray nVent CADDY KBT Installation

or standard tray mounting hardware

Ladder Cable Traystandard tray mounting hardware

Perforated Cable Traystandard tray mounting hardware

Optional Wire Retainer Clip**Required for fire rated applications

nVent CADDY Rod Lock Installation

nVent CADDY Speed Link Y-Hooks

nVent CADDY Speed Link Sway Brace

INSTRUCTION SHEET

3 OF 4CFS546 _ C

UTS SERIES - UNIVERSAL TRAY SUPPORT

nVent, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.

TECHNICAL SUPPORT:www.nVent.com © 2017, 2018 nVent All Rights Reserved

UTS150

UTS200

UTS300

Use center holes on template to pre-drill and install anchors, then hang bracket.

INSTRUCTION SHEET

4 OF 4CFS546 _ C

UTS SERIES - UNIVERSAL TRAY SUPPORT

nVent, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.

TECHNICAL SUPPORT:www.nVent.com © 2017, 2018 nVent All Rights Reserved