5
Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 1 1) The first time you will need to install the PE Micro Software and Drivers and activate your copy with PE Micro using the activation code on the CD case. 2) Attach the USB Multilink using the USB cable and install the drivers using the Windows automatic application and the disc from PE Micro. 3) The Blue LED should be lit up indicating that the USB driver is installed and working. Place the HCS08 Flash Programmer software on your desktop and double click to start and put in the activation code notated on the outside of the CD case. 4) With the programmer connected to the system and the Blue LED ON then attach the USB Multilink Interface cable to the board to be programmed. Make sure that the red stripe is at Pin1 on the board. Power the Bel Canto product ON and insure that the Yellow LED is lit indicating that power is present on the board. Then you can double click the HCS08 Flash Programmer icon on your desktop to start the PROGHCS08 Programmer dialogue below. The first screen to come up will look like Figure 1 if all is correct. Figure 1. Initial Screen 5) Click on Connect(Reset) to start the process.

Using the BDM Multink Programmer - Bel Canto Design · 2012. 1. 27. · Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 3 Figure 4. Screen after the programming algorithm

  • Upload
    others

  • View
    3

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Using the BDM Multink Programmer - Bel Canto Design · 2012. 1. 27. · Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 3 Figure 4. Screen after the programming algorithm

Using the BDM Multink Programmer

Bel Canto Design 1/3/2012 Page 1

1) The first time you will need to install the PE Micro Software and Drivers and activate your copy

with PE Micro using the activation code on the CD case.

2) Attach the USB Multilink using the USB cable and install the drivers using the Windows

automatic application and the disc from PE Micro.

3) The Blue LED should be lit up indicating that the USB driver is installed and working. Place the

HCS08 Flash Programmer software on your desktop and double click to start and put in the

activation code notated on the outside of the CD case.

4) With the programmer connected to the system and the Blue LED ON then attach the USB

Multilink Interface cable to the board to be programmed. Make sure that the red stripe is at

Pin1 on the board. Power the Bel Canto product ON and insure that the Yellow LED is lit

indicating that power is present on the board. Then you can double click the HCS08 Flash

Programmer icon on your desktop to start the PROGHCS08 Programmer dialogue below. The

first screen to come up will look like Figure 1 if all is correct.

Figure 1. Initial Screen

5) Click on Connect(Reset) to start the process.

Page 2: Using the BDM Multink Programmer - Bel Canto Design · 2012. 1. 27. · Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 3 Figure 4. Screen after the programming algorithm

Using the BDM Multink Programmer

Bel Canto Design 1/3/2012 Page 2

Figure 2. Programming Algorithm Selection 9S08GT32A.S8P

6) Select either the 9S08GT32A.S8P Algorithm or the 9S08QE64.S8P Algorithm and click Open

a. 9S08GT32A.S8P is used for: DAC3, DAC3.5VB, PRE3, CD2

b. 9S08QE64.S8P is used for: DAC1.5, DAC2.5, C5i, FM1, CD3t, C7R

Figure 3. Programming Algorithm Selection 9S08QE64.S8P

Page 3: Using the BDM Multink Programmer - Bel Canto Design · 2012. 1. 27. · Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 3 Figure 4. Screen after the programming algorithm

Using the BDM Multink Programmer

Bel Canto Design 1/3/2012 Page 3

Figure 4. Screen after the programming algorithm is loaded correctly

7) Now click on the Eraser icon circled below

Figure 5. Module has been erased

8) Now click on the Floppy Disc icon circled in Figure 6 and navigate to the Folder where you have

the .s19 programming files are stored and select the correct programming file for the product.

Page 4: Using the BDM Multink Programmer - Bel Canto Design · 2012. 1. 27. · Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 3 Figure 4. Screen after the programming algorithm

Using the BDM Multink Programmer

Bel Canto Design 1/3/2012 Page 4

Figure 6 shows the file for programming a CD2. Click on Open when the correct file has been

selected.

Figure 6. Select the correct programming .s19 file, CD2 Rev 3.36 is shown above.

Page 5: Using the BDM Multink Programmer - Bel Canto Design · 2012. 1. 27. · Using the BDM Multink Programmer Bel Canto Design 1/3/2012 Page 3 Figure 4. Screen after the programming algorithm

Using the BDM Multink Programmer

Bel Canto Design 1/3/2012 Page 5

9) Click on the Lightning Bolt icon circled in Figure 7 and the programming will start, completing

with the screen as shown below. You can now power down the unit and remove the

programmer cable. Power the unit back on to confirm that the correct firmware version is

present and working.

Note that you can access all of the firmware files at the following link:

http://www.belcantodesign.com/BCD/eOne_Programmer_Software/

This is kept up to date.