Userguide English Stlt

8/22/2019 Userguide English Stlt

1/63


2/63

Fujitsu Personal Systems, Inc. has made every effort to ensure theaccuracy and completeness of this document; however, because ongoingdevelopment efforts are made to continually improve the capabilities ofour products, we cannot guarantee the accuracy of the contents of this

document. We disclaim liability for errors, omissions, or future changesherein.

Fujitsu is a registered trademark of Fujitsu, Ltd.

Stylistic LT is a trademark of Fujitsu Personal Systems, Inc.

MS, MS-DOS, and Microsoft are registered trademarks of MicrosoftCorporation. Windows 98 is a trademark of Microsoft Corporation.

Pentium is a registered trademark of Intel Corporation. MMX is atrademark of Intel Corporation.

Intellisync is a registered trademark of Puma Technology, Inc.

All other products are trademarks or registered trademarks of theirrespective companies.

Copyright 1999Fujitsu Personal Systems, Inc.

No part of this publication may be copied, reproduced, or translated, without the priorwritten consent of Fujitsu Personal Systems, Inc. No part of this publication may be

stored or transmitted in any electronic form without the prior consent of Fujitsu

Personal Systems, Inc.


3/63

Agency Compliance

Warnings and Cautions

Warningsand Cautionsthat appear in this manual should be closely heeded.

Warnings represent situations that are potentially harmful to the user. Cautionsrepresent situations that can cause physical damage to the system or otherequipment.

UL Notices

Cautions

For continued protection against the risk of fire, replaceonly with the same type and rating of fuse.

There is a danger of explosion if the CMOS battery isincorrectly replaced. Replace only with the same orequivalent type recommended by the manufacturer.Dispose of used batteries according to manufacturer'sinstruction.

Changes or modifications not expressly approved byFujitsu Personal Systems, Inc. could void this users

authority to operate the equipment.

Warnings

The CMOS battery may explode if mistreated. Do notrecharge, disassemble, or dispose of in fire.

For spare battery packs, order only Fujitsu ModelsFMW29BP1 (6-cell) or FMW29BP2 (3-cell).

To charge battery packs FMW29BP1 or FMW29BP2externally, use only a Stylistic LTTM external batterycharger FMW51BC1.


4/63

iv

FCC Notices 0

Note: The Stylistic LT is available in a number of different configurations, as delineatedin the following table. For more detailed information about the FCC rules and their

applicability to the Stylistic LT pen tablet, refer to Appendix A of this document.

DECLARATION OF CONFORMITY

according to FCC Part 15

Responsible Party Name: Fujitsu Personal Systems, Inc.

Address: 5200 Patrick Henry DriveSanta Clara, CA

Telephone: 408-982-9500

Declares that product: Model: Stylistic LTComplies with Part 15 of the FCC Rules

This device complies with Part 15 of the FCC rules. Operation is subject tothe following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.

David Woo - Mgr. Agency Compliance May 28, 1999

Full Name / Title Date

Screen Type Modem? LAN? Cord Type Part Number

TFT NO NO US FMW2900TA01

TFT YES NO US FMW2901TA01

TFT NO YES US FMW2902TA01

TFT NO NO UK FMW2900TB01

TFT NO YES UK FMW2902TB01

TFT NO NO EURO FMW2900TC01

TFT NO YES EURO FMW2902TC01

CTF NO NO US FMW2900FA01

CTF YES NO US FMW2901FA01

CTF NO YES US FMW2902FA01

CTF NO NO UK FMW2900FB01

CTF NO YES UK FMW2902FB01

CTF NO NO EURO FMW290OFC01

CTF NO YES EURO FMW2902FC01


5/63

Table of ContentsWarnings and Cautions ............................................................................. iiiUL Notices.................................................................................................... iiiFCC Notices ................................................................................................. iv

Chapter 1

Getting StartedIncluded with the Stylistic LT Pen Tablet ............................................... 1-1Optional Accessories .................................................................................. 1-2Stylistic LT Pen Tablet Features................................................................ 1-3Status Indicators.......................................................................................... 1-6Connectors and Peripheral Interfaces..................................................... 1-9

Chapter 2Using the Stylistic LT Pen Tablet

System States ............................................................................................... 2-1Using the Pen............................................................................................... 2-3

Using Hovering Mode.................................................................... 2-3Starting the Pen Tablet ............................................................................... 2-4Using the Security Card ............................................................................. 2-4Shutting Down the System........................................................................ 2-7Suspending System Operation.................................................................. 2-7Resuming System Operation..................................................................... 2-9Using Hotpads............................................................................................. 2-10Charging the Battery Pack......................................................................... 2-12Removing and Installing the Battery Pack.............................................. 2-13Conserving Battery Power......................................................................... 2-15Modem Connection .................................................................................... 2-16LAN Connection......................................................................................... 2-17PC Card Slots............................................................................................... 2-18

Chapter 3Care and Maintenance

Protecting the Display Screen ................................................................... 3-1Storing the Stylistic LT Pen Tablet............................................................ 3-2Protecting the Stylistic LT Pen Tablet in Harsh Environments............ 3-3Avoiding Overheating ............................................................................... 3-3Cleaning the Display Screen...................................................................... 3-3Calibrating the Pen ..................................................................................... 3-4Replacing the Pen........................................................................................ 3-5Solving Problems ........................................................................................ 3-6

System Will Not Resume Operation ............................................ 3-6Display Screen Is Blank or Difficult to Read............................... 3-6Infrared Data Transfer Is Not Working....................................... 3-7Pen Tablet Is Not Responding to the Pen.................................... 3-7Cursor Is Not Tracking Pen........................................................... 3-7


6/63

vi

Audio Volume Is Too Low ............................................................ 3-8Configuring Peripherals Interfaces .............................................. 3-8

Chapter 4Using the Optional Peripherals

Stylistic LT Mini-Dock................................................................................ 4-1Installing the Stylistic LT into the Mini-Dock............................. 4-4

Removing the Stylistic LT from the Mini-Dock.......................... 4-5Stylistic LT Charge-Only Dock ................................................................. 4-5

Installing the Stylistic LT into the Charge-Only Dock .............. 4-6Removing the Stylistic LT from the Charge-Only Dock ........... 4-6

Stylistic LT Wireless Keyboard................................................................. 4-7Using the Wireless Keyboard........................................................ 4-7

Entering an Identification Code................................................ 4-8Encountering Problems when Using the Wireless Keyboard 4-8Replacing the Wireless Keyboard Batteries ............................ 4-9

Appendix A

Agency NoticesFCC Notices ................................................................................................. A-1

Notice to Users of Radios and Television.................................... A-1Notice to Users of the U.S. Telephone Network......................... A-1

DOC (Industry Canada) Compliance Notices ........................................ A-3Notice to Users of Radios and Television.................................... A-3Notice to Users of the Canadian Telephone Network............... A-3Avis Aux Utilisateurs Du Rseau Tlphonique Canadien...... A-4


7/63

1

Chapter 1

Getting Started

The Stylistic LT pen tablet is a high-performance, pen-based computer that isdesigned to operate under Windows 98. This chapter provides an overview of theStylistic LT pen tablet and its features.

Included with the Stylistic LT Pen Tablet

The following items are included with the Stylistic LT pen tablet:

Stylistic LT pen

Stylistic LT 3-cell battery pack AC adapter

Screen protectors (quantity: 2)

Hard disk drive with Windows 98 operating system installed in the pen tablet

Microsoft Windows 98 operating system user s guide with certificate ofauthenticity for operating system software

Certain Stylistic LT models are equipped with either an optional internal 56 Kbp

modem*or an optional internal LAN card.

* The 56 Kbps rate is nominal; due to FCC restrictions, actual rates are limitedto 53 Kbps.

The internal modem is available as an option in North America only.


8/63

1-2 Getting Started

Optional Accessories 1

The following optional accessories can be used with the Stylistic LT pen tablet. Referto the instructions provided with these accessories for details on their use.*

Auto Adapter FMWCB2

Mini-Dock FMW29PR1*

Charge-Only Dock FMW29CR1*

External Floppy Disk Drive FMWFD2

Wireless Keyboard*:

North America - FMWKB4A

United Kingdom -FMWKB4B

Germany - FMWKB4D

France - FMWKB4F

Holster A FMWCC34

Holster B FMWCC37

Folding Desk Stand FMWDS3

Compact Desk Stand FMWDS4

Carrying Case FMWCC38

Harsh Environment Case FMWCC39 Portfolio Case FMWCC40

Slipcase FMWCC41

Battery Pack (3 cell) FMW29BP2

Battery Pack (6 cell) FMW29BP1

External Battery Charger FMW51BC1

Screen Protectors (package of 12) FMWSP8

Pen (package of 5) FMW29PN1

Security Card (package of 10) FMW29SC1

* Instructions for use of the Stylistic LT mini-dock, the charge-only dock, andthe wireless keyboard are also included in Chapter 4 of this manual;instructions for the other options are shipped with the individual peripherals.


9/63

Stylistic LT Pen Tablet Features 1

Stylistic LT Pen Tablet Features

Features and controls that you use to operate the Stylistic LT pen tablet are describedbriefly below and illustrated in Figures 1-1 and 1-2. Details on using these featuresand controls are provided later in this manual.

Front and Side Features (Figure 1-1):

Display: Provides an area where you read information and enter data with thepen.

Status Indicators: Indicate the pen tablets power status, battery charge level,hard disk access, and hovering state. Reference Chapter 2 for additionalinformation on the hovering state.

Pen: Acts as the main pointing device that you use to run programs and enterdata. A pen holder is built into the pen tablet to store the pen when not in use.

Speaker: Allows you to play back audio files monaurally without externalhardware.

Microphone Jack: Allows you to connect an external microphone*.

Headphone Jack: Allows you to connect stereo headphones*.

Infrared I/O Port: Provides an infrared interface for communication with devicecompliant with IrDA Standard Revision 1.1.

Wireless Keyboard Infrared Port: Provides an infrared interface for

communication with the optional wireless keyboard*. Refer to Chapter 4 of thismanual for instructions on using the keyboard.

Hotpad Area: Contains several keys that allow you to change settings for thedisplay and speaker, and to allow emulation of a right mouse button. The hotpadalso let you select hovering mode and to Save-to-Disk by tapping with the pen.

Mini-Dock Connector: Allows you to install the Stylistic LT in an optionalmini-dock* for enhanced connectivity. Refer to Chapter 4 of this manual forinstructions on using the mini-dock.

Charging Contacts: Provide power to the system when installed in either the

mini-dock* or charge-only dock*.. Refer to Chapter 4 of this manual forinstructions on using the charge-only dock.

* These peripherals and accessories are sold separately.


10/63

1-4 Getting Started

Figure 1-1 Stylistic LT Pen Tablet Features (Front View)

Rear and Side Features (Figure 1-2): 1 DC Input Connector: Allows you to connect the AC adapter or auto adapter.*

Removable Battery Pack: Provides power to the system when not connected toAC power.

Battery Latch: Secures the removable battery pack when it is installed in thesystem.

Suspend/Resume Button: Allows you to suspend or resume system operation inorder to optimize battery life.

Reset Button: Restarts the pen tablet in the event of system difficulty. Note thatpressing this button results in loss of active data.


Pen Holder

Charge-only

Contacts

Hotpad Area

Speaker

Infrared

StatusIndicators

Mini-dockConnector

I/O Port

WirelessHeadphoneJack

MicrophoneJack

Display

KeyboardInfrared Port


11/63

Stylistic LT Pen Tablet Features 1

PC Card Door: Allows you to access PC Cards* installed in the PC Card slots.Note that Slot 2 is closest to the display.

Eject Buttons: Allow you to eject a PC Card from a PC Card slot.

USB Port: Allows you to connect Universal Serial Bus-compliant devices to thepen tablet.

Modem Port: Allows you to connect a standard RJ-11 telephone plug to the pentablets optional internal modem.


Figure 1-2 Stylistic LT Pen Tablet Features (Rear View)

The modem port is found only on those systems containing an internal modemThe internal modem is available as an option in North America only.

Removable

Suspend/ResumeButton

BatteryLatch

PC Card

Slots

EjectButtons

ModemPort USB

PortResetButtonDC Input

Battery Pack


12/63

1-6 Getting Started

Status Indicators 1

Icons appear in the Status display indicating the status of system functions such assystem power and battery charge level. The location of icons in the Status indicatorsection is shown in Figure 1-3.

Figure 1-3 Status Indicator Icons

(Power)

(Charging)

(HDD Access)

(Hovering/

Security)


13/63

Status Indicators 1

Table 1-1 shows how the LEDs associated with the individual icons are displayed,and describes what the variations of that display indicate. (If an icon LED is not lit, itindicates that the related system function is off or inactive.

Table 1-1 System Status Indications

IconLED

StatusColor System Function

Power

Icon

On Green Power On

(with battery between 13% and 100%)

Amber Power On

(during short periods when the system is checking remainingbattery life)

Red Power On(with battery at 12% or less charge, or no

battery installed)

Blink Green Suspend Mode

(with battery between 13% and 100%)

Amber Suspend Mode

(during short periods when the system is checking remaining

battery life)

Red Suspend Mode

(with battery at 12% or less charge, or nobattery installed)

Off Unlit Power Off or Save-to-Disk

Charging

Icon

On Green Charging is complete or running off of AC with no battery

installed.

Amber Charging is in process.

Red There is a problem with the battery.

Blink Green ---

Amber Battery temperature out of thermal range; charging has

stopped.

Red ---

Off Unlit No charging in process.


14/63

1-8 Getting Started

HDD

Access

Icon

On Green Displayed when the hard disk drive is being accessed.

Off Unlit Unlit when the hard disk drive is inactive.

Hovering/Security

Icon

On Green Operating in Hovering mode.

Blink Green Awaiting cancellation of security. (This occurs when the

computer is awaiting password input).

Off Unlit Operating in normal mode.

Table 1-1 System Status Indications (Continued)


15/63

Connectors and Peripheral Interfaces 1

Connectors and Peripheral Interfaces

Connectors and peripheral interfaces on the Stylistic LT pen tablet allow you toconnect a variety of devices. Figures 1-4 and 1-5 show locations of peripheralconnectors on the pen tablet. Additional features are shown for reference.

Figure 1-4 Right-Side Connectors and Interfaces

Figure 1-5 Left-Side Connectors and Interfaces

DC Input

Reset Button

USB Port

Modem Port (optional)

PC Card Door

Speaker HeadphoneJack

MicrophoneJack

InfraredI/O Port


16/63

1-10 Getting Started

Figure 1-6 Bottom Connectors and Interfaces

Table 1-2 provides a description of each peripheral connector and interface on theStylistic LT pen tablet. Each of the illustrated icons is embossed on the pen tabletcase.

Table 1-2 Peripheral Connectors and Interfaces

Connector/

PeripheralPen Tablet Icon Purpose

DC Input

Connector

Connects an external power source such as the AC

adapter or auto adapter.

Infrared I/O Port No icon An infrared transceiver built into the pen tabletallows you to communicate with other devices that

are compliant with the IrDA Standard Revision 1.1.

Effective range for infrared communication is about

3 feet, and within 15 degrees off of center. A clearline-of-sight path must exist between the IrDA port

on the pen tablet and the IrDA transceiver on the

other device.

Microphone Jack Connects an external microphone. The internal

microphone is disabled when you plug in an

external microphone.

Infrared

KeyboardPort

Mini-dockConnector(cover removed)

ChargingContacts


17/63

Connectors and Peripheral Interfaces 1-1

Wireless

Keyboard

Infrared Port

An infrared receiver built into the pen tablet allows

you to communicate with a wireless infrared

keyboard. The keyboard infrared port worksoptimally between 10 to 30 cm (approximately 4 in.to 12 in.) from the keyboard infrared port, located

on the bottom edge of the pen tablet. Ensure that

there is a clear line-of-sight path between theinfrared receiver on the pen tablet and the infrared

transmitter on the keyboard. Refer to Chapter 4 for

more information on the wireless keyboard.

Headphone Jack Connects stereo headphones or powered external

speakers.

Mini-dock

Connector*No icon Connects the Stylistic LT mini-dock or other

approved docking device. Refer to Chapter 4 for

additional information about the mini-dock.

USB Port

Connects Universal Serial Bus-compliant devices

to the pen tablet.

PC Cards

Two Type II PC Cards or one Type III PC Card can

be installed in the PC Card slots.

Modem Port No icon This port location is used to connect a telephoneline to the optional internal modem using a

standard RJ-11 telephone plug. Note that the

modem is available only in North Americansystems.

Charging

Contacts

No icon The charge-only contacts are used when the pen

tablet is installed in either the optional mini-dock or

charge-only dock. Refer to Chapter 4 for more

information on the mini-dock and charge-only dock.

* To avoid damaging the pen tablet or your peripheral device, shut down the system or

suspend system operation before connecting or disconnecting a peripheral device to thisport.

Table 1-2 Peripheral Connectors and Interfaces

Connector/

PeripheralPen Tablet Icon Purpose


18/63

1-12 Getting Started


19/63

2

Chapter 2

Using the Stylistic LT Pen Tablet

This chapter covers the fundamental concepts, basic system operation and use, andsystem functions of the Stylistic LT pen tablet. You should familiarize yourself with thiinformation before you attempt to operate the system.

System States

Before you begin using the Stylistic LT pen tablet, review the different system states (omodes) that the pen tablet can use. Being familiar with these system states will help yodetermine whether it is appropriate to turn on, resume, suspend, or shut down thesystem when you begin a new session or end your current session. System behavior fo

each system state is described briefly in the following, with each system state listed indecreasing order of power usage:

Fully On (normal) stateThe system is running and the display screen is on. The system responds to the penor other input.

Idle and Standby statesSome system functions are regulated or turned off to conserve power. The displayscreen may be turned off. The system returns to the Fully On state when pen activit

or other input is detected.

Suspend Modes: When you press the Suspend/Resume button, the system willeither go into Suspend-to-RAM mode, or Save-to-Disk mode. The mode thesystem enters was determined when the system was configured -- usually by thereseller who sold you the pen tablet or by your IS department. Contact one ofthose individuals for more information on how your pen tablet is configured.

v Suspend-to-RAM modeWhen the Suspend option is set, data is saved to system RAM when theSuspend/Resume button is pressed.

v Save-to-Disk modeWhen Save-to-Disk is set (or when the Save-to-Disk hotpad key is tapped),data is written in the Save-to-Disk area on the hard disk.


20/63

2-2 Using the Stylistic LT Pen Tablet

Off stateAll system functions are turned off to conserve power. The system does not respondto the pen or other input. The system boots at the next system power-on.

Your system may be configured to enter some of these states automatically after aperiod of inactivity to conserve battery power.

When you use the Stylistic LT pen tablet, you can change the current system state in anumber of ways, depending on which state the system is in. To determine the currentsystem state, observe the Power icon in the Status display. Table 2-1 gives thedifferent system states represented by the Power icon and describes how you canchange the system state from the current state.

Table 2-1 Changing System States

* Information in Table 2-1 is supplied to help you understand which system states your system

can enter from the current system state. Refer to the procedures on starting the system,

shutting down the system, suspending system operation, and resuming system operationgiven later in this chapter for details on changing the current system state.

Your system may be configured to use either Suspend-to-RAM mode, Save-to-Disk mode, ormay use both modes sequentially.

Power Icon

Appearance

Current State To Change State*

Power icon

displayed

continuously

Fully On,

Idle,

or

Standby

To turn the system off, shut down the system using

a software shut down.

To enter the Suspend-to-RAM or Save-to-Diskstate,

suspend system operation using either a hardware or

software suspend, or tap the Save-to-Disk hotpad.

Power icon

blinkingSuspend-to-RAM To turn the system on, resume system operation by

pressing the Suspend/Resume button.

To turn the system off, resume system operation,then shut down your system.

Power icon not

displayed

Off or

Save-to-Disk

To turn the system on, start your system, or resume

system operation.


21/63

Using the Pen 2

Using the Pen

You can use the pen to select items and run programs on the Stylistic LT pen tablet lika mouse on a desktop computer. Programs that support handwriting recognition also

allow you to write characters directly on the screen with the pen. You can also use thpen as a drawing tool if your program provides a drawing or inking area on the screen

The screen reacts with the pen when the pen tip touches the screen. The pen tipgenerally corresponds to the left button on a two-button mouse. In order to emulate right mouse button, tap on the right mouse button on the keypad. The pen tipautomatically returns to left mouse button mode when the screen is tapped again.For more information on using the hotpads, refer to the Using Hotpads sectionlater in this chapter.

Here are some hints that may help you use the pen more effectively.

Tomove the cursor, hold the pen tip lightly on the display screen and move the pen

Tostart a program, double-tap the pen tip (tap the pen tip twice rapidly) on theprogram icon as you would double-click a mouse.

Toselect an object, tap the pen tip once on the object.

Todrag an object, place the pen tip directly over the object, then press and hold thpen tip against the display screen while you move the pen.

Note: Installing or ejecting a PC Card while the pen is touching the screen could result in

pen recognition failure. If this occurs, suspend and resume system operation one omore times, until the pen again becomes operational.

Using Hovering Mode

Selecting the Pen Hovering icon on the Stylistic LT keypad provides the user withbetter cursor control. When the hovering option is enabled, the cursor can be

Caution

The Stylistic LT pen can be damaged if used improperly. Treat

the pen as you would any writing instrument. Observe the

following guidelines for proper pen handling:

The pen tip is spring-loaded to provide writing comfort and toprevent screen damage. Avoid tapping it on surfaces otherthan the pen tablet screen.

To prevent pen loss or damage, it should be stored in thepen holder when not in use.


22/63


positioned over an icon without activating it. This is useful when you are performingprocedures that require accurate cursor positioning, such as when simulating mouserollover, selecting a small icon, or beginning a paint session.

To enable hovering, tap the Pen Hovering icon on the keypad. The Hovering systemstatus indicator light illuminates green when hovering is selected.

To disable hovering, tap the Pen Hovering icon again. The Hovering systemindicator light is off when hovering is not selected.

Starting the Pen Tablet 2

Follow the procedure below to start the Stylistic LT pen tablet. Before you begin,confirm that the system is off. To do so, observe the Status display. If the Power iconis not lit in the Status display, the system is off and it is safe to perform thisprocedure. If the Power icon is lit (either blinking or on continuously), do notperform this procedure. See System States earlier in this chapter for details onoperational modes represented by the Power icon.

1. Press the Suspend/Resume button to start the system.

2. Ensure that the battery pack in your pen tablet is sufficiently charged, or connect anexternal power source such as the AC adapter or auto adapter to your pen tablet. SeeStatus Display in Chapter 1 to determine the percentage of charge represented bythe Charging icon in the Status display.

After performing system initialization, the system starts the operating system installed

on the hard disk drive. Once the operating system is running, you can use the system. Ifyou are prompted to enter your password, refer to the following section entitled Usingthe Security Card.

Using the Security Card 2

The Stylistic LT can be used with an optional security card that allows you to enter anexclusive password. This ensures that only authorized persons can access a particularsystem and/or its hard disk drive, depending upon the selections made when thesystem was configured.


23/63

Using the Security Card 2

Note: This feature may not be enabled, depending upon how your system is configured.Contact either your reseller or your IS department for more information on howyour pen tablet is configured.

Figure 2-1 Stylistic LT Security Card

Figure 2-2 Using the Security Card

A B C D E F G

H I J K L M N

O P Q R S T U

V W X Y Z / *

Card Locator/Escape hole

Card Locator/Enter hole

Password

input holes(A through Z,*, and / )

2-2a. 2-2b.

2-2c. 2-2d.


24/63


When prompted by your Stylistic LT pen tablet to enter a password, perform thefollowing procedure:

1. Ensure that the system speaker is on. Audible signals are used later in thisprocedure.

2. Place the security card on the display screen in a position similar to Figure 2-2a.Note that the card can be placed anywhere along the edge, as long as it ispositioned with the cut corner facing the upper left.

3. Hold the card firmly against an edge of the screen frame. With your pen, tap theCard Locator/Escape hole just under the cut corner, as in Figure 2-2b.

If you hear two beeps in succession, proceed to step 4.

If you hear four beeps in succession, return to step 2.

4. With your pen, tap the Card Locator/Enter hole, as in Figure 2-2c.

If you hear two beeps in succession, proceed to step 5.

If you hear four beeps in succession, return to step 2.

Note: Your password is created during system configuration. To determine yourpassword, check with your system administrator or supervisor.

5. Tap in your password using the password input holes, as in Figure 2-2d. Up toseven characters can be used for a password (including letters and symbols). Ifyou make a mistake while entering your password, tap the Card Locator/Escape

hole, and repeat steps 2 through 4.

6. After entering your password, tap the Card Locator/Enter hole.

7. If you enter the wrong password, you receive a Setup Warning message. If thisoccurs, tap Continue and return to step 2.

Notes: If you have difficulty entering a password, or you move the security card whileentering the password, tap the [Esc] key on the keypad until the hovering/security LED stops blinking. At that point, begin the input procedure again.

If you enter the incorrect password three times in a row, you receive a SystemDisabled message, and access to the computer is disabled. If this happens, press thereset switch to restart the computer.


25/63

Shutting Down the System 2

Shutting Down the System

Follow these steps to shut down and turn off your system:

1. If system operation has been suspended, resume system operation. See ResuminSystem Operation later in this chapter for details.

2. Save your work and close all running programs.

3. Choose Shut Down from the Windows 98 Start menu and carry out the Shut Dowcommand.

The system is now in the Off state.

Suspending System Operation

The Stylistic LT pen tablet allows you to suspend the system operation without closin

programs or exiting the operating system. Use this feature to conserve battery powewhen a system shutdown is inconvenient. There are two different suspend modes:Suspend-to-RAM and Save-to-Disk. In Suspend-to-RAM mode, active data is savedby maintaining power to RAM while most other system components are poweredoff. In Save-to-Disk mode, active data is stored on the hard disk drive and powerusage is reduced to the same level used in the Off state.

To suspend system operation, perform one of the following procedures:

Press the Suspend/Resume button, or carry out the Suspend command from you

operating system or power management program. (If your system is configured tsuspend operation using Save-to-Disk mode, which is explained later in thisprocedure, a message is displayed while data is saved to your hard disk.)

Tap the Save-to-Disk hotpad key.

The Power icon blinks when system operation is suspended-to-RAM, and is offwhen saved-to-disk. The state your system enters is dependent upon how yoursystem is configured. At this point, programs that were running are stopped,active data is saved, and the system enters one of two different low-power statesor suspend modes, as explained in the following paragraphs.

Caution

If you are replacing the battery pack, be sure to Save-to-Disk before you

remove the battery pack. Failure to do so may result in loss of your unsaved

data.


26/63


4. Observe the Power icon in the Status display to determine which suspend modeyour system is using.

Power icon is blinking: Suspend-to-RAM modeIn this mode, active data is saved by maintaining power to RAM while mostother system components are powered off. The Power icon in the Status displayindicates the battery charge level. A fully charged 3-cell battery pack canmaintain data in RAM for approximately 7 days; a fully charged 6-cell batterypack can maintain data for approximately 14 days. A partially charged batterypack will maintain data in RAM for proportionately less time.

Power icon is not displayed:Save-to-DiskmodeIn this mode, active data is stored on the hard disk drive and power usage isreduced to the same level used in the Off state. When the system is inSave-to-Diskmode, the Power icon is not visible in the Status display. In thismode, there is no danger of losing data if battery power is lost.

If you have successfully performed this procedure, system operation is now suspended.Refer to Resuming System Operation later in this chapter to resume system operation.Also, note the following with regard to suspending system operation:

You can remove the battery pack while the system is in Save-to-Disk mode, but notSuspend-to-RAM mode (unless the AC adapter is connected). To prevent losingunsaved data, always perform Save-to-Disk before you remove the battery pack.

Your system may be configured to suspend operation automatically after a period ofinactivity.

Your system may be configured to enter Save-to-Disk mode automatically after aperiod of time in Suspend-to-RAM mode.

The system uses a small amount of battery power when in Suspend-to-RAM mode.Eventually, the battery will become fully discharged.

Note: If you will not be using the system for an extended period of time, shut down thesystem rather than using Suspend-to-RAM mode.

If the battery pack charge drops to the Low-Battery Warning level while the system

is running, the Power icon will turn red and blink intermittently. If this occurs,suspend system operation, shut down the system, or attach an external powersource, such as the AC adapter, to the pen tablet.

If the battery charge drops to the Critically Low level while the system is running,the system is forced into Suspend-to-RAM mode. If this occurs, you must connect anappropriate external power source such as the AC adapter before you can resume


27/63

Resuming System Operation 2

system operation. (If the battery charge drops to the Critically Low level while thsystem is in Suspend-to-RAM mode, the system stays in Suspend-to-RAM mode

Suspending system operation interrupts data communications; however, someprograms may block the system from suspending to prevent an interruption.

The Suspend/Resume button on your system may be configured during system

setup to act as an On-only button. If this is the case, pressing the Suspend/Resume button will not suspend system operation as described here. Contactyour IS department or reseller if your system configuration is not suitable.

If your system is equipped with a PC Card that allows you to connect to a wired owireless network, you may be logged off the network after a period of inactivitywhile system operation is suspended. Contact your network administrator or locahelp desk for details on log-off parameters for your network.

Resuming System Operation

To resume system operation, (from either Suspend-to-RAM or Save-to-Disk modes),press the Suspend/Resume button.

From Suspend-to-RAM modeAfter a few seconds, the system returns to the Fully On state and system operationresumes. Note that the display turns on shortly before the pen becomes active due tthe power-up sequences observed by the system.

From Save-to-Disk modeActive data is read from the hard disk drive, and after 15 to 30 seconds, the systemreturns to the Fully On state.

Note that power to several system components must be restored before systemoperation resumes. Allow sufficient time for system operation to resume beforeattempting to use the system. If your system uses Save-to-Disk mode, it will takelonger to resume operation as compared to using Suspend-to-RAM mode. Time isneeded to read data from the hard disk drive.

Use the system as you normally would once system operation resumes.

All programs resume at the point where execution stopped when system operation wasuspended.


28/63


Using Hotpads 2

The Hotpad area consists of several pen-active keys on the right side of the systemdisplay that you can use to change several settings. The hotpads allow you to:

Adjust the display and speaker settings

Invoke right mouse button

Invoke hovering capability

Use as a numeric pad

Generate a Save-to-Disk request

To use a hotpad key, tap directly on it with the pen. You can also press and hold thepen tip against the Volume, Contrast, and Brightness hotpad keys to automatically

repeat the hotpad function. The location of each hotpad key is shown in Figure 2-3.

Figure 2-3 Stylistic LT Hotpad Arrays

ESC

BSTAB

SPACE

0

1 2 3

4 5 67 8 9

Save-to-Disk Key

CursorKeys

NumericKeys

EscapeKey

MouseRight

ButtonHoveringKey

SpeakerKeysBrightness

KeysContrastKeys

Save-to-Disk Key

Key

Display Key


29/63

Using Hotpads 2-1

A summary of each hotpads function is given below.

Note: Equivalent key codes are included for applicable hotpad keys. These can be used whea keyboard is connected.

Table 2-2 Hotpad Keys

Icon Name Description

Escape Functions the same as the [Esc] key on a typical

keyboard.

Display Device Each time the Display Device hotpad key is tapped,the display unit is switched (in the following order):

LCD -> CRT -> both LCD and CRT -> LCD...

Save-to-Disk Starts the Save-to-Disk operation to save data to

the disk.

Cursor Control Acts in the same way as the cursor keys on a

keyboard. (Up, Down, Left, and Right).

Numeric Keypad Acts in the same way as the numeric keypad on a

keyboard.

Right Mouse Button Switches the pen function from left mouse button to

right mouse button emulation.

ESC

BSTAB

998877

654

321

0

SPACE


30/63


Charging the Battery Pack 2

The Stylistic LT battery pack can be charged while it is installed in the pen tablet. To doso:

1. Connect a DC power source, such as the AC adapter, to the DC input connector onthe pen tablet. The Charging icon appears in the Status display. If the battery packcharge level is below 90%, the battery pack begins charging and the Charging icon

Pen Hovering Switches the hovering mode on or off. Throughout

the hovering mode, the hovering/security status

indicator is lit green.

Speaker Volume Down Lowers the speaker volume.

Speaker Volume Up Increases the speaker volume.

Speaker Volume Mute Toggles the speaker off and on.

Brightness Down Decreases the luminance of the display backlight.

Brightness Up Increases the luminance of the display backlight.

Contrast Down Provides more contrast on CTF models only. Thishotpad has no effect on TFT models.

Contrast Up Flattens the contrast on the CTF models only. Thishotpad has no effect on TFT models.

Table 2-2 Hotpad Keys

Icon Name Description


31/63

Removing and Installing the Battery Pack 2-1

appears in the Status display. If the battery pack charge is 90% or higher when yoconnect DC power, the battery pack will not charge; this prevents overcharging thbattery pack.

2. Look at the Power icon in the Status display to determine the approximate percent ocharge in the battery pack. See Status Indicators in Chapter 1 of this manual foa description of the Power icon.

As long as DC power remains connected to the pen tablet, the charging process continueuntil the battery pack charge reaches 100%. Charge times shown in Table 2-3 are for fully discharged battery pack charging while the pen tablet is and is not in use.

Table 2-3 Battery Pack Charging Time

Also note the following with respect to charging the battery pack:

You can use the system, suspend system operation, or shut down and turn off thsystem without interrupting the charging process; however, using the system whilthe battery pack is charging will cause the battery pack to charge at a slower rate, anoted in Table 2-3.

As noted in the procedure above, the system will not begin charging the batterypack if the battery pack charge level is 90% or higher when the system is initiallyconnected to external DC power. (This prevents the battery pack from beingovercharged.)

The Stylistic LT battery pack uses lithium ion battery cells which have nomemory effect. You do not need to discharge the battery pack before you begincharging.

Removing and Installing the Battery Pack

The battery pack can be removed from the pen tablet and swapped with a chargedbattery pack. The battery pack can then be charged in an external charger if one isavailable. To remove the battery pack from the pen tablet:

Approximate Charge Time

(tablet not in use)

Approximate Charge Time

(tablet in use)

3-Cell 6-Cell 3-Cell 6-Cell

2 hours 3 hours 4 to 6 hours 8 to 12 hours


32/63


1. Choose one of the following:

Save your data by tapping on the Save-to-Disk icon on the keypad.

Close all running programs, then shut down the system.

Plug in an external DC power source.

2. Slide the battery latch to the unlocked position. (See Figure 2-4.)

3. Slide the battery pack out of the pen tablet.

If you are using an external battery charger, refer to the instructions provided with thebattery charger.

To install the battery pack, slide the battery pack into the pen tablet until it is firmly

seated. The spring-loaded battery latch automatically clicks into place.

Once the battery pack is installed, you can start your system and use the system as younormally would.

Caution

The Stylistic LT pen tablet does not have a bridge battery.Prior to removing the battery pack, be sure to save your data

by tapping the Save-to-Disk icon on the keypad or connect an

AC adapter. Save-to-RAM will not suffice, since all data inRAM is lost when the battery is removed.

Warning

To prevent pinching your fingers, keep them clear of the areabetween the battery pack and the pen tablet when you install

the battery pack.


33/63

Conserving Battery Power 2-1

Figure 2-4 Removing and Installing the Battery Pack

Conserving Battery PowerYou can extend the charge life of your battery pack by conserving battery power. Afully charged battery pack can run the system under normal use in most applicationfor approximately 2 hours (standard, 3-cell battery pack) or 4 hours (extended, 6-cellbattery pack). Your results may vary depending on your application and how thesystem is configured. Here are some suggestions to help you conserve battery power

Use an external power source such as the AC adapter to power the system whenpossible.

Suspend system operation if you wont be using the system for a few minutes.

Shut down the system if you wont be using the system for an extended period otime.

Use power management timeouts to help you conserve power automatically.

Battery

Latch

Removable

Battery Pack


34/63


Modem Connection 2

Note: The optional internal 56 Kbps modem installed in some models of the Stylistic LTpen tablet* has actual transfer rates of 53 Kbps (receive), 33.6 Kbps (send), and14.4 Kbps (fax). Download rates are limited to 53 Kbps in the United States due toFCC restrictions.

* The internal modem is available as an option in North America only.

The Stylistic LT pen tablet is designed to accept a standard RJ-11 telephone plug.Connect the plug to the modem jack located on the right of the pen tablet, as shownin Figure 2-5. The telephone plug can be installed whether or not the pen tablet haspower applied.

If you need assistance configuring the Stylistic LT pen tablet modem, contact your localhelp desk or your reseller.

Figure 2-5 Connecting the Modem

ModemPlug

PhoneJack


35/63

LAN Connection 2-1

LAN Connection

Some models of the Stylistic LT have an internal LAN card that allows the computerto be connected to a high-speed LAN by 100BASE-TX Ethernet.

Note: An optional Stylistic LT mini-dock (Part Number FMW29PR1) is required inorder to use the LAN option.

1. To use the internal LAN, first shut the system down and unplug the AC Adapteif necessary.

2. Install the system into the optional Stylistic LT mini-dock. Refer to Chapter 4 ofthis manual for instructions on use of the mini-dock.

3. Connect the AC adapter to the mini-dock, then connect the LAN cable betweenthe mini-dock and the LAN hub, as shown in Figure 2-6.

Figure 2-6 Connecting the LAN

4. To remove the LAN connector from the mini-dock, press the tab on the plug whil

pulling the plug away from the system.

LAN Hub

LAN Plug

ACAdapterPlug

Mini-Dock


36/63


PC Card Slots 2

The Stylistic LT pen tablet has two PC Card slots that allow you to install up to twoType II PC Cards using both slots 1 and 2, or a single Type III PC Card using slot 1only. Slot 2 is closest to the screen; slot 1 is closest to the back of the system. SeeFigure 2-7 for PC Card slot location.

Not es: Type II PC Cards will work in either slot, with one exception: zoomed video PCCards must be installed in slot 1.

Some PC Cards require that the system be shut down before installation. Checkthe user manual for your particular card before installing it.

To install a PC card, position it with the label facing up and slide it through the PCcard door shutters. When it is properly seated, the eject button will extend away fromthe computer. Flip the eject button into the eject button tray such that it is parallel

with the system.

To remove a PC Card from a PC Card slot, flip up the adjacent eject button so that itis perpendicular to the system, then push it in. When the PC Card pops out, carefullyremove it from the slot.

If you need assistance installing a PC Card in the Stylistic LT pen tablet, contact yourlocal help desk or your reseller.

Figure 2-7 PC Card Slots

Eject Buttons

PC Card 2 (upper slot)

PC Card 1 (lower slot)

PC Card


37/63

3

Chapter 3

Care and Maintenance

This chapter provides pointers on how to care for and maintain your Stylistic LT pentablet.

Protecting the Display Screen

The Stylistic LT pen tablet is designed to provide you with years of service. Using ascreen protector will help ensure that the screen remains as clear as possible. Wheninstalled, the screen protector becomes a durable, replaceable, antiglare writingsurface that protects the display screen from abrasion.

To obtain additional screen protectors use Fujitsu part number FMWSP8 (12-pack)when ordering. Additional information about installation is included with the screenprotectors.

To install a new screen protector on your pen tablet:

1. If a screen protector is already installed on the display screen, remove it beforeinstalling the new screen protector. The screen protector is held onto the displayscreen surface by a thin strip of adhesive around the edges. A notch in one corneof the screen protector allows you to slide your fingernail under the screenprotector for easy removal.

2. Clean the adhesive residue from the screen surface by gently wiping the residueusing a soft cotton cloth dampened with denatured alcohol. Ensure that all filmhas been removed from the screen before applying a new screen protector.

Caution

During normal use of the pen tablet, small particles from the

environment can become embedded in the pen tip andscratch the screen. To prevent scratching the screen, ensure

that a screen protector is installed before using your pen

tablet. The warranty does not cover a screen that is scratchedas a result of not using a screen protector.


38/63

3-2 Care and Maintenance

3. Remove the protective coating from the adhesive side of the new screen protectorfirst.

4. Apply the screen protector to the display screen surface. When doing so, orientthe screen protector with the adhesive side of the screen protector facing thedisplay screen and the notched corner of the screen protector toward the lowerleft corner of the display screen.

5. Remove the protective plastic cover from the face of the screen protector.

6. Apply pressure to the screen protector with your finger using a continuouswiping motion along the edges. The adhesive sets completely within 48 hours. Toensure a good seal between the screen protector and the display, do not lift thescreen protector from the display once it has been applied.

7. Clean any residue left behind by the protective coating from the exposed surfaceof the screen protector by wiping gently with a soft cotton cloth dampened withdenatured alcohol. Wipe the screen protector with a soft dry cloth to remove anylow-tack adhesive; this will help to prevent the pen tip from squeaking.

The screen protector is now installed.

Storing the Stylistic LT Pen Tablet 3

Store the Stylistic LT pen tablet in the Fully Off state with a fully charged batterypack installed. The Stylistic LT battery pack always provides power to some systemcomponents, even when the system is in the Fully Off state. If you plan to store thesystem with the battery pack removed, be sure to Save-to-Disk prior to storing;failure to do so could result in lost data. You can store the pen tablet for about 14days (standard 3-cell battery pack) or 25 days (extended 6-cell battery pack) with afully charged battery pack installed. After this period, the battery pack should berecharged or replaced with a charged battery pack.

Cautions

Cleaning the screen surface with denatured alcohol mayresult in streaking. If streaking occurs, buff the screensurface lightly with a soft, dry cloth.

The Stylistic LT pen tablet is not waterproof. Do not pour

liquids on the system or wash it with a soaked cloth.


39/63

Protecting the Stylistic LT Pen Tablet in Harsh Environments 3

Protecting the Stylistic LT Pen Tablet in Harsh Environments

The Stylistic LT pen tablet is designed for use in environments where there is nodirect exposure to rain, mist, sprays, dirt, or other abrasive particles. The optionalStylistic LT harsh environment case (FMWCC39) and the Stylistic LT screen protecto(FMWSP8) provide some protection in these environments, as well as from physicaldamage due to shock or vibration.

Note that the harsh environment case does not render the pen tablet waterproof,dustproof, or submersible.

The pen tablet is easily used while installed in the harsh environment case. Foradditional information on the Stylistic LT harsh environment case as well asadditional carrying cases, portfolio cases, and holsters, contact your reseller.

Avoiding Overheating

The Stylistic LT pen tablet monitors its internal temperature. As the internaltemperature approaches the tolerable limits of heat-sensitive components, systemfunctions are automatically limited or turned off to prevent heat damage.

To avoid overheating the pen tablet, do not charge the pen tablet while it is in theharsh environment case unless the system is either suspended or off. Using properpower management techniques while the pen tablet is in the harsh environment casealso helps to prevent overheating.

Cleaning the Display ScreenTo clean the pen tablet display screen, wipe the screen surface gently using a softcotton cloth slightly dampened with water or denatured alcohol. Using denaturedalcohol may resulting in streaking. If this occurs, gently buff the surface with a soft,dry cloth.

Caution

The Stylistic LT pen tablet is not waterproof. Do not pour

liquids on the pen tablet or wash the pen tablet with a heavilysoaked cloth.


40/63


Calibrating the Pen 3

You calibrate the pen to adjust the cursor position on the screen relative to theposition of the pen tip. If the cursor is not displayed under the pen tip when you usethe pen, you should calibrate the pen.

Pen calibration may be required due to the following situations:

The previous user of the Stylistic LT pen tablet writes with the opposite hand.

The system has been in use for some time and the pen has not been recalibrated.

To Calibrate the Pen 3

1. In the Control Panel, double-tap the Pen Configuration icon. Select theCalibration property sheet, then click on Pen Calibration.

2. Position the Stylistic LT pen tablet as you normally would during use. Be sure tohold the pen at the angle that you regularly use. Touch the screen only with thepen tip; if you inadvertently touch the screen with your finger or hand during thecalibration process, faulty calibration may result.

3. Perform the calibration steps according to the instructions on the screen. Thecalibration utility displays a cross-hair symbol in each corner of the screen, onecorner at a time. Hold the pen as you normally would while using the system and,as accurately as possible, tap the center of each crosshair as it is displayed.

A dialog box is displayed after you tap the last of the four cross-hair symbols.

4. In the dialog box, tap your response. (If you do not tap any of the buttons within20 seconds, your new calibration settings are discarded and previous calibrationsettings are used.)

If you are satisfied that you tapped the cross-hairs accurately, tap OK. Thetaps that you performed in step 3 are then used to calibrate the screen.

If you do not want to use your taps to calibrate the screen, tap Cancel.

If you want to try again, tap Recalibrate. The calibration instructionsreappear.

If you have successfully performed the procedure above, the pen is now calibrated,and you can use the system as you normally would.


41/63

Replacing the Pen 3

Replacing the Pen

With use, the pen tip may become worn or may pick up abrasive particles that canscratch the screen. A damaged or warped tip may not move freely, causingunpredictable results when using the pen. If your pen exhibits any of these problemsreplace the pen.


42/63


Solving Problems 3

Solutions to some common problems are described in the following sections. If youare experiencing a problem with your Stylistic LT pen tablet that you cannot solve bytaking the actions described, contact your local help desk or your reseller for furtherassistance.

System Will Not Resume Operation 3

If the system will not resume operation after system operation has been suspended,check the following possible causes:

The battery pack may be either defective or discharged to a critically low level.When the battery pack reaches the critically low level, the system is forced intoSuspend-to-RAM mode to avoid a total system power failure. To correct thisproblem, connect an external power supply (such as the AC adapter).

The system may be at the critical thermal limit. To avoid damage to heat-sensitivecomponents, the system enters Suspend-to-RAM mode when it gets too hot.System operation cannot be resumed until the pen tablet cools off to a tolerabletemperature. Move the pen tablet to a cooler location and prevent direct sunlightfrom shining onto the pen tablet.

Display Screen Is Blank or Difficult to Read 3

If the display screen on your Stylistic LT pen tablet appears blank or is unreadable,confirm that the system is running (the Power LED is displayed continuously on the

Status display), and check the following:

The system brightness may be set too low, causing the screen to appear too dark.Use the brightness hotpad to adjust the screen brightness.

An external monitor may be selected. Tap on the Display Select hotpad todetermine whether the pen tablet display screen is selected.

The video timeout may have expired. Tap on the display screen to reactivate thedisplay. Note that this is a normal, power-saving feature.

Transflective (CTF) systems only: The display contrast settings may be set toextreme high or low level causing the screen to appear blank. Try adjusting thecontrast setting using the hotpads. Note that the surrounding temperature willaffect the display contrast. You may need to adjust the contrast periodically tocompensate for changes in environment temperature.


43/63

Solving Problems 3

Infrared Data Transfer Is Not Working

Note: For troubleshooting problems between the Stylistic LT and the optional wirelesskeyboard, refer to the section of Chapter 4 entitled Encountering Problems whenUsing the Wireless Keyboard.

If you are experiencing problems transferring data over the systems infrared

interface, check the following:

Can the IrDA port on the pen tablet see the IrDA port on the other device? Adirect line-of-sight path must exist between the IrDA port on the pen tablet andthe IrDA port on the other device.

The distance between the two devices must not be more than approximately 3 feeor 1 meter.

The center line of the IrDA port on the pen tablet must not be more than 15

degrees from the center line of the IrDA port on the other device.

The device with which you are trying to communicate must be compliant with thIrDA Standard Revision 1.0 or 1.1.

Pen Tablet Is Not Responding to the Pen

If your pen tablet is not responding to the pen, connect an external keyboard (eitherwired or wireless) to the system to see if it responds to keyboard commands. If thesystem doesnt respond to the keyboard, the application or system may havecrashed, and it may be necessary to reset the system. Note that the optionalmini-dock is required to connect a wired keyboard.

Cursor Is Not Tracking Pen

If the cursor on the screen is not accurately tracking the pen or appears to bemisaligned with the pen, calibrate the pen. See Calibrating the Pen earlier in thischapter for details.


44/63


Audio Volume Is Too Low 3

If the audio volume on your pen tablet speaker or external headphones is too low,check the following:

Ensure that the speaker (or headphone output if using headphones) is enabled. To

do so, tap the Speaker Mute hotpad. The system beeps when the speaker orheadphone output is turned on using the Speaker Mute hotpad.

Ensure that the volume level set with the Volume hotpads is set to an audiblelevel.

Ensure that the mute box in the system volume control (accessible from thesystem tray) is not set.

Ensure that any volume control in your audio software is set to an audible level.

Configuring Peripherals Interfaces 3

Note that peripheral devices such as serial port A can be disabled during the BIOSSetup. If the peripheral interface you want to use does not appear to be working withyour peripheral device, ensure that it is enabled in the BIOS. Contact your local helpdesk or reseller if you need assistance using BIOS Setup.


45/63

Stylistic LT Mini-Dock 4

Chapter 4

Using the Optional Peripherals

Several custom options are available to support your Stylistic LT pen tablet, as listedin the Optional Accessories section of Chapter 1. This chapter contains informationto assist you in using three of the more complex peripherals: the Mini-Dock(FMW29PR1), the Charge-Only Dock (FMW29CR1), and the Wireless Keyboard(North America: FMWKB4A, United Kingdom: FMWKB4B, Germany: FMWKB4D,and France: FMWKB4F).

Note: Each of the optional items is delivered with instructions on its use. The informatiocontained in this chapter is provided as a quick reference for three of the morecommonly used peripherals.

Stylistic LT Mini-Dock

The Stylistic LT mini-dock is designed to extend the connectivity of your pen tabletby providing a number of ports that are not available on the system. Refer to Figures4-1, 4-2, and 4-3 for port locations. The mini-dock can also be used as a charging dockfor periods when the pen tablet is not being used.

The Stylistic LT mini-dock provides the following interfaces:

PS/2-style Mouse PortUsed for connecting a mouse with a PS/2-style connector.

AC Adapter PortUsed for connecting the AC adapter to supply power to the system.

Parallel PortOrdinarily used for connecting a printer.

Serial PortUsed for connecting a serial device.

Video PortUsed for connecting a video monitor for displaying the contents of the Stylistic LTscreen.

Floppy Disk Drive PortUsed for connecting the optional floppy disk drive (FMWFD2).


46/63

4-2 Using the Optional Peripherals

PS/2-style Keyboard PortUsed for connecting a keyboard with a PS/2-style connector.

LAN PortUsed for connecting the pen tablets optional internal LAN card to a LAN hub.

Note: The LAN port can only be used with systems that have been pre-configured with

the optional internal LAN card. The mini-dock is required in order to use the LANcard; there is no LAN port on the pen tablet.

Figure 4-1 Mini-Dock Peripheral Interfaces

The viewing angle of the mini-dock can be adjusted to four different positions. Thebottom of the support bail on the rear of the support platform (see Figure 4-3) snaps

into one of four slots. When storing the mini-dock, flip the bail up against the back ofthe support platform to allow the platform to lie flat.

FloppyDisk DriveFMWFD2

Stylistic LTPen Tablet

PC Card

Video

Monitor

PrinterPS/2-StyleMouse

Stylistic LTMini-Dock

PS/2-Style

Keyboard


47/63

Stylistic LT Mini-Dock 4

Figure 4-2 Right-Side of Stylistic LT Mini-Dock

Figure 4-3 Rear and Left-Side of Stylistic LT Mini-Dock

PS/2-style

Mouse Port

LAN Port

AC Adapter Port

Parallel Port

Serial Port Video Port

Floppy DiskDrive Port

PS/2-styleKeyboard Port

Support Bail

SupportPlatform


48/63


Installing the Stylistic LT into the Mini-Dock 4

1. Shut down the system and disconnect the AC adapter, if used.

2. Position the pen tablet against the positioning guide and the back of themini-dock.

3. Slide the pen tablet into the tray at the bottom of the mini-dock and press it down

firmly until it is seated, as shown in Figure 4-4. The alignment guide in the bottomof the tray ensures that the system is properly seated over the connector.

4. Connect the AC adapter to either the pen tablet or mini-dock and re-start yoursystem.

Figure 4-4 Installing the Stylistic LT in the Mini-Dock

Cautions

Dropping conductive material onto the charging contactscould result in internal damage to the pen tablet circuitry.

Prior to installing the Stylistic LT into the mini-dock, besure to disconnect the AC adapter first. Failure to do socould result in damage to the system or the mini-dock.

Stylistic LTPen Tablet

Stylistic LTMini-Dock

Positioning

Guide

Mini-DockBase


49/63

Stylistic LT Charge-Only Dock 4

Removing the Stylistic LT from the Mini-Dock

1. Shut down the system and disconnect the AC adapter from the mini-dock or pentablet, if required.

2. While holding the base of the mini-dock with one hand, grasp the pen tablet at thtop and firmly pull it straight up from the base.

3. Reconnect the AC adapter and restart your system.

Stylistic LT Charge-Only Dock

The Stylistic LT charge-only dock is designed to allow you to use the pen tablet onyour desktop as it charges from the AC adapter. The charge-only dock is the samesize as the mini-dock, but the AC adapter plug is the only connector on the dock.

Figure 4-5 Inserting Stylistic LT into Charge-Only Dock

The viewing angle of the charge-only dock can be adjusted to four differentpositions. The bottom of the support bail on the rear of the support platform (seeFigure 4-6) fits into one of four slots. When storing the dock, flip the bail up againstthe back of the support platform to allow the platform to lie flat.

AC Adapter Port


50/63


Figure 4-6 Charge-Only Dock Support Bail

Installing the Stylistic LT into the Charge-Only Dock 4

1. Position the pen tablet against the positioning guide and the back of thecharge-only dock.

2. Slide the pen tablet into the tray at the bottom of the dock and press it downfirmly until it is seated, as shown in Figure 4-5. The alignment guide in the bottomof the tray ensures that the system is properly seated over the charging pins.

Removing the Stylistic LT from the Charge-Only Dock 4

1. Disconnect the AC adapter from the charge-only dock or pen tablet, if required.

2. While holding the base of the dock with one hand, grasp the pen tablet at the topand firmly pull it straight up from the base.

Caution

Dropping conductive material onto the charging contactscould result in internal damage to the pen tablet circuitry.

Prior to first installing the Stylistic LT into the charge-onlydock, be sure to disconnect the AC adapter from the dock.

Failure to do so could result in damage to the system orthe dock.

Support Bail SupportPlatform


51/63

Stylistic LT Wireless Keyboard 4

Stylistic LT Wireless Keyboard

The wireless keyboard allows you to transmit between the Stylistic LT and thekeyboard using infrared rays.

Using the Wireless Keyboard

There are several key points to remember when using the wireless keyboard:

The pen tablet should be securely seated upright, either in a mini-dock,charge-only dock, or portfolio carrying case.

The keyboard should be positioned so that its infrared transmitter is directlyfacing the infrared photosensor on the pen tablet (see Figure 4-7).

Figure 4-7 Keyboard-to-Stylistic LT Wireless Transmission

The keyboard performs optimally when it is within 30 cm (approximately 12inches) of the pen tablet, although it will operate at greater distances.

Do not attempt to use a wireless keyboard at the same time as a wired keyboard(via the PS/2-style connector on the mini-dock). The wired keyboard takesprecedence over the wireless, so the wireless keyboard becomes disabled.

If a key on the keyboard is depressed continuously, the battery will automaticallyshut off after approximately 60 seconds.

Pen TabletInfrared

WirelessKeyboardInfraredTransmitter

Photosensor


52/63


Entering an Identification Code 4

When multiple keyboards and pen tablets are used in a small area, it may benecessary to assign an individual identification code to each keyboard/pen tabletpair. Assigning identification codes prevents interference or cross-talk betweenclosely situated keyboards and systems.

The identification code assigned to a keyboard/pen tablet pair is temporary. Thecode is cancelled whenever the computer is turned off, suspended, or reset. When thesystem is initially turned on, the pen tablet identification code defaults to 0 (zero). Atthat point, any keyboard will work with the pen tablet until a new code is entered viaa keyboard.

Once a new code is entered, only the coded keyboard will work with the pen tabletunless other keyboards are individually coded with the same identification code.

The system will recognize the code of the first keyboard with which it is used; other

keyboards will not be recognized unless they are assigned the same code as the firstkeyboard used.

For example, if two keyboards (A and B) are within infrared range of the pen tablet,they can both be used when the system is initially reset or suspended. If theidentification code for keyboard A is set to 123 and it is used with the pen tablet first,the pen tablet will recognize 123 as the code; keyboard B would be disabled unlessyou enter 123 as its code. If you assign keyboard A the identification code 123, butuse keyboard B first, the pen tablet will only recognize keyboard B (with the defaultcode of 0).

To enter an identification code for your keyboard, perform the following steps:

Note: In the following step, be sure to press and hold down the keys in the same order asthey appear below, and leave them depressed until after the code is entered. There isno on-screen indication that the code has been entered.

1. Press [Fn]+[Left Alt]+[Left Shift]+[ID Code]. Use up to seven keys for the IDCode, consisting of number characters 0 through 7.

Encountering Problems when Using the Wireless Keyboard 4

The wireless keyboard is used in the same way as a normal wired keyboard. Intypical operation, you should encounter few problems in transmitting data to yourpen tablet. If your keyboard fails to perform properly, check for the followingcircumstances:


53/63

Stylistic LT Wireless Keyboard 4

The infrared transmitter on the keyboard is not properly aligned with the pentablet infrared photosensor.

The keyboard is too far from the pen tablet, or something is obstructing theline-of-sight between the ports.

The remote control for another device (such as a television or wireless

headphones) is being operated in the same vicinity as the keyboard.

The infrared transmitter on the keyboard and/or the infrared photosensor on thpen tablet are directly exposed to sunlight or bright artificial light.

The infrared transmitter on the keyboard and/or the infrared photosensor on thpen tablet are dirty.

The keyboard batteries are dead (see the section of this chapter entitledReplacing the Wireless Keyboard Batteries).

The keyboard may not have the correct identification code entered for the systemwith which it is being used (see the section of this chapter entitled Entering anIdentification Code).

Replacing the Wireless Keyboard Batteries

Occasionally the batteries in the wireless keyboard will require replacement. Thekeyboard uses two AAA-size alkaline batteries.

Caution

Ensure that the correct polarities (+ and -) are used wheninstalling new batteries in the keyboard.

Dont mix old and new batteries.

If the keyboard wont be used for a long period, remove thebatteries to prevent electrolyte leakage. If the batteriesleak, clean out the battery compartment with a damp cloth,then dry thoroughly.

Handle the batteries carefully, and dispose of old batteries

in accordance with local regulations.


54/63


To replace the batteries in your wireless keyboard:

1. Close any open programs on your pen tablet.

2. Remove the wireless keyboard battery compartment cover by pinching the latchtowards the cover, then pulling the cover away from the keyboard, as in Figure4-8a.

3. Remove the old batteries and dispose of them in accordance with localregulations.

4. Insert two new AAA-type alkaline batteries into the battery tray. Be sure toobserve correct polarity, as shown in Figure 4-8b.

5. Replace the battery compartment cover.

Figure 4-8 Replacing the Wireless Keyboard Batteries

Battery

Compartment

Cover

a. b.

Latch -+ -

+


55/63

Agency Notices A

Appendix A

Agency Notices

FCC Notices

This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC rules.

Changes or modifications not expressly approved by Fujitsu Personal Systems, Inc.,could void the users authority to operate the equipment.

Notice to Users of Radios and Television

These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If theequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet that is on a different circuit than thereceiver.

Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables must be employed with this equipment to ensurecompliance with the pertinent RF emissions limits governing this device.

Notice to Users of the U.S. Telephone Network

Note: Some configurations of the Stylistic LT do not have an internal modem. Thefollowing information applies only to those systems with an internal modem.

The Stylistic LT pen tablet is supplied with an internal modem which complies withPart 68 of the FCC rules. On the pen tablet is a label that contains the FCCRegistration Number and Ringer Equivalence Number (REN) of this system, along


56/63

A-2 Appendix

with other information. If requested, users must provide their telephone companywith the following information:

The telephone number to which the pen tablet is connected

The Ringer Equivalence Number (REN) for this equipment

The information that the system requires a standard modular jack type USOCRJ-11C which is FCC Part 68-compliant

The FCC Registration Number

This equipment is designed to be connected to the telephone network or premiseswiring using a standard modular jack type USOC RJ-11C which is FCC Part68-compliant.

The REN is used to determine the number of devices you may connect to yourtelephone line and still have all those devices ring when your number is called. Too

many devices on one line may result in failure to ring in response to an incoming call.In most, but not all, areas, the sum of all of the devices should not exceed five (5). Tobe certain of the number of devices you may connect to your line, as determined bythe RENs, contact your local telephone company.

If this equipment causes harm to the telephone network, your telephone companymay discontinue your service temporarily. If possible, they will notify you inadvance. If advance notice is not practical, they will notify you as soon as possible.You will also be advised of your right to file a complaint with the FCC.

This fax modem also complies with fax branding requirements per FCC Part 68.

If you experience trouble with this equipment, please contact your supportrepresentative.

Your telephone company will probably ask you to disconnect this equipment fromthe telephone network until the problem is corrected and you are sure that theequipment is not malfunctioning.

This equipment may not be used on coin service telephones provided by your

telephone company. Connection to party lines is subject to state tariffs. Contact yourstates public utility commission, public services commission, or corporationcommission for more information.

FCC rules prohibit the use of non-hearing aid compatible telephones in the followinglocations or applications:


57/63

Agency Notices A

All public or semipublic coin-operated or credit card telephones.

Elevators, highways, tunnels (automobile, subway, railroad, or pedestrian) whera person with impaired hearing might be isolated in an emergency.

Places where telephones are specifically installed to alert emergency authoritiessuch as fire, police, or medical assistance personnel.

Hospital rooms, residential health care facilities, convalescent homes, andprisons.

Workstations for the hearing impaired.

Hotel, motel, or apartment lobbies.

Stores where telephones are used by patrons to order merchandise.

Public transportation terminals where telephones are used to call taxis or toreserve lodging or rental cars.

In hotel and motel rooms at least ten percent of the rooms must contain hearing-

aid compatible telephones that will be provided to hearing impaired customerson request.

DOC (Industry Canada) Compliance Notices

This digital apparatus does not exceed the Class B limits for radio noise emissionsfrom digital apparatus as set forth in the radio interference regulations of theCanadian Department of Communications.

Le prsent appareil numrique nmet pas de bruits radiolectriques dpassant les

limites applicables aux appareils numriques de classe B prescrites dans le rglemensur le brouillage radiolectrique dict par le Ministre des Communications duCanada.

Notice to Users of Radios and Television

This Class B digital apparatus meets all requirements of the CanadianInterference-Causing Equipment regulations.

Cet appareil numrique de la classe B respecte toutes les exigences du rglement sur

le matriel brouilleur du Canada.

Notice to Users of the Canadian Telephone Network

The Canadian Industry Canada label identifies certified equipment. This certificationmeans that the equipment meets certain telecommunications network protective,


58/63

A-4 Appendix

operational, and safety requirements. The Department does not guarantee theequipment will operate to the users satisfaction.

Repairs to telecommunication equipment should be made by a Canadian authorizedmaintenance facility. Any repairs or alterations not expressly approved by FujitsuPersonal Systems, Inc. or any equipment failures may give the telecommunications

company cause to request the user to disconnect the equipment from the telephoneline.

The connecting arrangement code for this equipment is CA11A.

The Load Number is 0.2.

The Load Number assigned to each telephone terminal device denotes thepercentage of the total load to be connected to a telephone loop or circuit to be usedby the device to prevent overloading. The termination on a loop may consist of anycombination of devices such that the total of the load numbers of all devices does notexceed 100.

Avis Aux Utilisateurs Du Rseau Tlphonique Canadien 4

Ltiquette canadienne Industrie Canada identifie lquipement certifi. Cettecertification signifie que lquipement satisfait certaines normes de protection,dexploitation et de scurit des rseaux de tlcommunications. Le dpartement negarantit pas le fonctionnement de lquipement la satisfaction de lutilisateur.

Le Stylistic LT possede un modem interne conforme aux normes de certificationdIndustrie Canada pour protger les rseaux de tlcommunications et satisfaire auxnormes de scurit. Avant de connecter cet quipement une ligne tlphonique,lutilisateur doit vrifier sil est permis de connecter cet quipement aux installationsde tlcommunications locales. Lutilisateur est averti que mme la conformit auxnormes de certification ne peut dans certains cas empcher la dgradation du service.

Caution

For safety, users should ensure that the electrical ground of the

power utility, the telephone lines, and the metallic water pipes are

connected together. Users should not attempt to make suchconnections themselves but should contact the appropriate electric

inspection authority or electrician. This may be particularlyimportant in rural areas.


59/63

Agency Notices A

Les rparations de lquipement de tlcommunications doivent tre effectues parun service de maintenance agr au Canada. Toute rparation ou modification, quinest pas expressement approuve par Fujitsu Personal Systems, Inc., ou toutedfaillance de lquipement peut entrainer la compagnie de tlcommunications exiger que lutlilisateur dconnecte lquipement de la ligne tlphonique.

Le code darrangement de connexion de cet quipement est CA11A.

Le numro de charge est 0.2.

Le numro de charge assign chaque terminal tlphonique indique le pourcentagde la charge totale pouvant tre connect une boucle ou un circuit tlphonique,utilis par ce priphrique afin de prvenir toute surcharge. La terminaison duneboucle peut tre constitue de nimporte quelle combinaison de priphriques desorte que le total de numros de charge de tous les priphriques nexcde pas 100.

Avertissement

Pour assurer la scurit, les utilisateurs doivent vrifier que laprise de terre du service dlectricit, les lignestlphoniques et les conduites deau mtalliques sontconnectes ensemble. Les utilisateurs NE doivent PAS tenterdtablir ces connexions eux-mmes, mais doivent contacterles services dinspection dinstallations lectriquesappropris ou un lectricien. Ceci peut tre particulirement

important en rgions rurales.


60/63

A-6 Appendix


61/63

Index

Index

A

AC Adapter port, 4-1Auto Adapter, 1-2

B

battery charger, external, 1-2battery gauge, 2-13battery latch, 1-4battery pack

3-cell, 1-26-cell, 1-2

charging, 2-12charging time, 2-13critically low level, 2-8, 2-9low-battery warning, 2-8no memory effect, 2-13overcharge protection, 2-13removing and installing, 2-13, 2-14storing in system unit, 3-2will not begin charging, 2-13

battery powerconserving, 2-15

used in suspend-to-RAM mode, 2-8brightness, 2-10

hotpads, 2-10

C

Calibrating, 3-4calibrating the pen, 3-4care and maintenance, 3-1carrying case, 1-2charge-only contacts, 1-11charge-only cradle, 1-2, 4-5

installing the Stylistic LT, 4-6removing the Stylistic LT, 4-6

charging icon, 1-7charging the battery pack, 2-12cleaning the display screen, 3-3compact desk stand, 1-2

configuring peripherals interfaces, 3-8connectors and peripheral interfaces, 1-9

conserving battery power, 2-15contrast hotpads, 2-10critically low battery level, 2-8, 2-9cursor

moving with pen, 2-3not tracking pen, 3-7

cursor key hotpad, 2-10

D

DC input connector, 1-4, 1-10determining suspend mode, 2-8display

screen is blank, 3-6screen, cleaning, 3-3

display area, 1-3display select hotpad, 2-10dragging an object, 2-3

E

eject buttons, 1-5external battery charger, 1-2external floppy disk drive, 1-2

F

floppy disk drive port, 4-1folding desk stand, 1-2Fully On, 2-1

Hhard disk drive access icon, 1-8harsh environment case, 1-2, 3-3headphone jack, 1-3, 1-11holster, 1-2hotpad area, 1-3hotpads, using, 2-10


62/63

Index-2

hovering key hotpad, 2-10hovering mode, 2-3

disabling, 2-4hovering/security icon, 1-8

I

icons, 1-7charging, 1-7HDD access, 1-8hovering/security, 1-8power, 1-7

identification code, wireless keyboard, 4-8Idle or Standby state, 2-1infrared data transfer not working, 3-7infrared keyboard port, 1-11interfaces

Documents

Userguide English Stlt