User’s Manual CAP 5351.1 Configuration, programming and ...€¦ · Table 2: Documents CAP 535 Document Number CAP 535 1.1 (This document) Configuration, programming and setting

User’s ManualCAP 535*1.1

Configuration, programming and settingtool package

This manual belongs to:

__________________________

Chapter Page

Contents

Introduction .............................................................................................................5

Intended use of this manual .................................................................................5

Intended audience................................................................................................5

What is in this manual? ........................................................................................5

How to find more information ...............................................................................6

Application...............................................................................................................7

Tool package CAP 535 ........................................................................................7

Requirements ..........................................................................................................9

PC, operative system and help viewer.................................................................9

Product family support .........................................................................................9

Installing the CAP 535 tool package ...................................................................11

Installing the CAP 535 software .........................................................................11

Installing the CAP 535 documentation ............................................................... 15

Installing Acrobat Reader................................................................................... 17

Installing Internet Explorer ................................................................................. 21

Uninstalling the CAP 535 software..................................................................... 25

2

About this Manual

This is the user’s manual for CAP 535*1.1

Document number: 1MRK 511 086-UEN

Version: 1.1

Revision: 01

Issue date: February 2001

Data subject to change without notice

We reserve all rights to this document, even in the event that a patent is issued and adifferent commercial proprietary right is registered. Improper use, in particular repro-duction and dissemination to third parties, is not permitted.

This document has been carefully checked. If the user nevertheless detects anyerrors, he is asked to notify us as soon as possible.

The data contained in this manual is intended solely for the product description and isnot to be deemed to be a statement of guaranteed properties. In the interests of ourcustomers, we constantly seek to ensure that our products are developed to the latesttechnological standards.

As a result, it is possible that there may be some differences between the HW/SWproduct and this information product.

Author´s address:ABB Automation ProductsSubstation Automation DivisionSE-721 59 VästeråsTel: +46 (0) 21 32 13 00Fax: +46 (0) 21 14 69 18Internet: http://www.abb.com/automation

© ABB Automation Products AB 2001

31MRK511086-UEN*1.1-01

About this Manual

4 1MRK511086-UEN*1.1-01

Intended use of this manual

Introduction

Introduction

1 Intended use of this manual

CAP 535 is a collection of programming, configuration and setting tools and librariesfor a range of protection and control terminals.

This manual can be used to get an overview of CAP 535 and its contents and informa-tion on PC requirements and supported terminal product families. It also provides nec-essary information to install the tool package CAP 535.

2 Intended audience

This manual can be used by installers, commissioners and system engineers.

2.1 Responsibilities

In order to fully understand the contents of this manual, you should have basic engi-neering knowledge and specific knowledge in system automation, depending on yourpurpose.

3 What is in this manual?

This manual is organized into chapters according to the intended audience so that eachchapter corresponds to user’s needs.

Chapter 1 gives an introduction to the manual.

Chapter 2 gives an overview of CAP 535 and its contents.

Chapter 3 specifies the requirements for your PC and operative system. It also showswhich product families and releases are supported by this tool package.

Chapter 4 describes how to install the CAP 535 tool package.

51MRK511086-UEN*1.1-01

7

Tool package CAP 535

Application

Application

5 Tool package CAP 535

The tool package CAP 535 is a collection of programming, configuration and setting tools and libraries for a range of protection and control terminals.

The package also contains the User’s Manuals in pdf-format for the tools, as well as Acrobat Reader to view the manuals.

Internet Explorer 4 is also provided. It is needed for the help system in the PST.

When you install CAP 535*1.1 software you get the following tools and libraries:

Table 1: Included tools and libraries.

Tool/Library Release Description

CAP 531 1.5 The configuration and programming tool

CAP/REX50020 2.0 Configuration library for terminal REX 500 * 2.0





CAP/RET52121 2.1 Configuration library for terminal RET 521 * 2.1



PST 1.1 The parameter setting tool

PST/REX50020 2.0 Parameter setting library for terminal REX 500 * 2.0





PST/RET52121 2.1 Parameter setting library for terminal RET 521 * 2.1



1MRK511086-UEN*1.1-01

8 1MRK511086-UEN*1.1-01

Tool package CAP 535

Application

When you install the documentation for CAP 535*1.1, you get the following docu-ments:

Table 2: Documents CAP 535

Document Number

CAP 535 * 1.1 (This document)

Configuration, programming and setting tool package

User’s Manual

1MRK 511 086-UEN

CAP 531 * 1.5

Parameter Setting tool

User’s Manual

1MRK 511 088-UEN

PST * 1.1

Configuration and Programming tool

User’s Manual

1MRK 511 089-UEN

How to find more information

Introduction

4 How to find more information

The following manuals provide complementary information:

• CAP 531 Configuration and Programming tool, User’s Manual,1MRK 511 088-UEN

• PST Parameter Setting tool, User’s Manual, 1MRK 511 089-UEN

6 1MRK511086-UEN*1.1-01

PC, operative system and help viewer

Requirements

Requirements

6 PC, operative system and help viewer

Table 4: Requirements on operative system and help viewer

7 Product family support

The following product families and releases are supported by this tool package:

Table 3: Requirements on PC

Item Minimum required

Processor / Frequency Pentium / 166 MHz

RAM 64 MByte

Disk space 150 MByte

Monitor / Resolution VGA compatible / 800 x 600, 256 colors

CD-ROM drive Needed to install the tool package

Operative System Release Help viewer

Windows NT 4

(Microsoft version)

4.0, service pack 3 or higher Internet Explorer 4

Table 5: Supported product families

Product family Releases Description

REX500 *2.0, *2.1, *2.2.*2.3 and *3.0

The REX500 series of control and protection ter-minals.

RET521 *2.1, *2.3 and*3.0

The RET521 transformer protection terminal.

91MRK511086-UEN*1.1-01

Product family support

Requirements

10 1MRK511086-UEN*1.1-01

Installing the CAP 535 software

Installing the CAP 535 tool package


This chapter describes how to install the different parts in the CAP 535 tool package.

It describes how to install the software, Acrobat Reader and Internet Explorer.

�Note!When installing in Windows NT, you need to log in as administrator.

8 Installing the CAP 535 software

This section describes how to install the CAP 535 software.

1 Insert the CAP 535 installation CD in the CD-ROM drive of your personal com-puter.

2 Select the Control Panel in the Start menu.

3 Double-click Add/Remove Programs, and then Click the Install/Uninstall tab.

4 Click the Install button and follow the instructions. Browse to the Programfolder on the CD-ROM drive and install_CAP 535.exe.

5 Click the Finish button to run the installation program.

The following dialog appears:

Figure 1: Welcome dialog

111MRK511086-UEN*1.1-01



6 Read the message and click OK if you want to continue with the installation.


Figure 2: Select Terminal Libraries dialog.

7 Select the check boxes for all terminal libraries you want to install.

8 If you want to change the destination for the CAP 531 installation, click theChange button to the right of the CAP 531 destination box.


Figure 3: Select Destination dialog.

12 1MRK511086-UEN*1.1-01



9 Select the drive and the folder where the CAP 531 software shall be installed,and then click OK.

10 If you want to change the destination for the PST installation, click theChange button to the right of the PST destination box.

The dialog in figure 3 appears.

11 Select the drive and the folder where the PST software shall be installed, andthen click OK.

12 Click Next.


Figure 4: System Information dialog.

13 Check the information and choose one of the following two steps:

• To reenter any information, click Back.

• To start the installation, click Install.

The CAP 535 software package is now installed in your computer, showing you ainstallation progress bar.

14 When the installation is complete, click OK to restart your computer.

After restarting your computer, you can begin using the tools and the terminallibraries in the CAP 535 software package.

131MRK511086-UEN*1.1-01



The installation sets up the following program entries in the start menu underPrograms\CAP 531:

Figure 5: CAP 531 start menu

The installation sets also up the following program entries in the start menu underPrograms\PST:

Figure 6: PST start menu

The help function in the Parameter Setting Tool uses Internet Explorer. If you donot have Internet Explorer on your computer, you have to install it. Please see sec-tion “Installing Internet Explorer”.

14 1MRK511086-UEN*1.1-01

Installing the CAP 535 documentation


9 Installing the CAP 535 documentation

This section describes how to install the documentation for CAP 535.


2 Using the Windows Explorer, select the Documentation folder on the CD-ROM drive and double-click install_CAP 535doc.exe.


Figure 7: Welcome dialog

3 Read the message and click OK if you want to continue with the installation.


Figure 8: Destination dialog

151MRK511086-UEN*1.1-01

Installing the CAP 535 documentation


4 Select the drive and the folder where the CAP 535 documentation shall beinstalled, and then click Next.


Figure 9: System information dialog

5 Check the information and do one of the following.

• To reenter any information, click Back.

• To start the installation, click Install.

The CAP 535 documentation is now installed into your computer, showing you ainstallation progress bar.

6 When the installation is complete, click OK.

The installation sets up the documentation entries in the start menu under Pro-grams\CAP531 and under Programs\PST.

The documents are in pdf-format, you need Acrobat Reader to view them. If you donot have Acrobat Reader on your computer, you have to install it. Please see thesection “Installing Acrobat Reader”.

16 1MRK511086-UEN*1.1-01

Installing Acrobat Reader


10 Installing Acrobat Reader

This section describes how to install Acrobat Reader. Acrobat Reader is used to viewthe documentation for the CAP 535.


2 Using the Windows Explorer, select the Acrobat Reader folder on the CD-ROM drive and double-click ar32e301.exe.


Figure 10: Acrobat Reader installation start dialog

3 Click Yes if you want to continue.

The installation is prepared and the following dialog appears:

Figure 11: Acrobat Reader installation Welcome dialog

171MRK511086-UEN*1.1-01



4 Click Next.


Figure 12:Acrobat Reader Software License Agreement dialog

5 Read the License Agreement and if you accept it, click Yes.


Figure 13:Acrobat Reader installation, Choose Destination Location dialog

18 1MRK511086-UEN*1.1-01



6 Click Browse.


Figure 14: Acrobat Reader installation, Choose Directory

7 Type or select the folder for the installation, and then click OK.

8 Click Next in the Choose Destination Location dialog.

The Acrobat Reader is now installed into your computer, showing you a installationprogress bar.

Then the following dialog appears:

Figure 15: Acrobat Reader installation, Setup Complete

191MRK511086-UEN*1.1-01



9 Do one of the following:

• Click to clear the Display Acrobat Reader 3.01 Readme file check box, andthen click Finish.

The Good-bye message appears.

• Click to set the Display Acrobat Reader 3.01 Readme file check box, and thenclick Finish

The Readme file is shown in WordPad.

After you have exited Wordpad, the Good-bye message appears.

10 Click OK.

The installation of Acrobat Reader is now ready. The following program entries areset up in the start menu under Programs\Adobe Acrobat:

Figure 16:Acrobat Reader start menu

20 1MRK511086-UEN*1.1-01

Installing Internet Explorer


11 Installing Internet Explorer

This section describes how to install Internet Explorer 4. Internet Explorer is used forthe help function in the Parameter Setting Tool.


2 Using the Windows Explorer, select the Internet Explorer folder on the CD-ROM drive and double-click ie4setup.exe


Figure 17: Internet Explorer installation Welcome Dialog

3 Click Next.


211MRK511086-UEN*1.1-01



Figure 18:Internet Explorer License Agreement

4 Read the License Agreement and if you accept it, click the I accept the agree-ment option button, and then click Next.


Figure 19:Internet Explorer Installation Option

5 Select Browser Only Installation.

You can also select Standard or Full Installation, depending on how much function-ality you want to have. See the Description area.


22 1MRK511086-UEN*1.1-01



Figure 20: Internet Explorer Destination Folder

6 Type the installation folder, or click Browse to select it. Then click Next.

The Internet Explorer is now installed into your computer, showing you an installa-tion progress bar.

The following dialog then appears:

Figure 21: Internet Explorer installation, Setup has finished installing components.

7 Click OK to finish the setup.

The following dialog appears after a while:

231MRK511086-UEN*1.1-01



Figure 22:Internet Explorer installation, restart your computer

8 Click OK to restart your computer

After the restart, Internet Explorer is ready to use.

24 1MRK511086-UEN*1.1-01

Uninstalling the CAP 535 software


12 Uninstalling the CAP 535 software

This chapter describes how to uninstall the CAP 535 software.

�Note!Only the programs that were installed will be removed. The user data, CAP 531projects and Parameter Setting data, will be kept. Also, all installed configurationlibraries and all installed parameter setting libraries, will be kept.

1 Select the Control Panel in the Start menu.

2 Double-click Add/Remove Programs, and then Click the Install/Uninstall tab


Figure 23: Add/Remove programs properties

3 Select CAP 535 in the list and then click Add/Remove.

The uninstall for CAP 535 starts and the following dialog appears:

251MRK511086-UEN*1.1-01

Uninstalling the CAP 535 software


Figure 24:Select Uninstall Method

4 Click Automatic, and then click Next.


Figure 25:Perform Uninstall

5 Click Finish to start the uninstallation.

The CAP 535 software is now uninstalled, showing you a progress bar.

26 1MRK511086-UEN*1.1-01

Customer feedback report

Product:

ABB Automation Products AB would appreciate your comments on this product.Please grade the following questions by selecting one alternative per category. Youranswer will enables us to improve our products.

How do you grade the quality of the product?

Excellent Poor

Total impression

Useability

Functionality

Human-man interface

Comments: __________________________________________________________

____________________________________________________________________

____________________________________________________________________

How do you grade the quality of the documentation?

Excellent Poor

Total impression

Layout

Illustrations

Readability

Easy to find

Content structure

Comments: __________________________________________________________

____________________________________________________________________

____________________________________________________________________

Rem

ove

from

bind

er

27

Customer feedback report

Rem

ove

from

bind

er

Suggestions for improvments:

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

_____________________________________________________________________

Please send this report to:

ABB Automation Products ABSubstation Automation DivistionSA-T, Support LineSE-721 59 VästeråsSweden

By facsimile:

Send to + 46 (0) 21 14 69 18

28

29

Program:

This card registers your program and makes you eligible to receive information aboutfuture updates.

Name:

_____________________________________________________________________________________Title:

____________________________________________________________________________________Company: Dept.

____________________________________________________________________________________Address:

____________________________________________________________________________________

____________________________________________________________________________________City: State: Zip:

____________________________________________________________________________________Phone:

____________________________________________________________________________________Fax:

____________________________________________________________________________________

Program supplied by:

____________________________________________________________________________________Adress:

____________________________________________________________________________________

____________________________________________________________________________________City: State: Zip:

____________________________________________________________________________________Phone:

____________________________________________________________________________________Date of receival of the program:

____________________________________________________________________________________Program serial Nr:

____________________________________________________________________________________

Fascimile:

Please send this registration card to ABB Automation Products AB, Sweden department Substation Auto-mation, SA-T, Support Line (+46 21 14 69 18)

Software Registration FormR

emov

efr

ombi

nder

PlacePostage

Here

ABB Automation ProductsSubstation Automation DivisionSA-T, Support LineSE-721 59 VästeråsSweden

To be folded

Tape here

Rem

ove

from

bind

er

SOFTWARE LICENSE

• This ABB Automation Products AB License Agreement (”License”) grants you the nonexclusive right to useone copy of the enclosed software program (”SOFTWARE”) on a single computer (i.e., with a single CPU) ata single location at any time. If you have multiple Licenses for the SOFTWARE you may have as many copiesof the SOFTWARE in use as you have Licenses.

• The software is owned by ABB AB or its suppliers and is protected by Swedishcopyright laws, international treaty provisions, and all other applicable national laws. Therefore you must treattheSOFTWARE as any other copyrighted material (e.g., a book or musical recording) except that if thesoftware is not copy protected you may either (a) make a copy of the SOFTWARE solely for backup or archivalpurposes, or (b) transfer the SOFTWARE to a single hard disk provided you keep the original solely forbackup or archival purposes. You may not copy the Documentation accompanying the SOFTWARE.

• The License is effective until terminated. This License will terminate automatically without notice fromABB AB if you fail to comply with any provision of this License. Upon termination youshall return the diskettes containing the SOFTWARE and all Documentation to ABB ABand destroy any copies of the SOFTWARE or any portions of it which has not been returned to ABB

AB, including copies resident in computer memory.

• You may not rent, lease, lend, sell or give away the SOFTWARE, but you may transfer your rights underthis ABB AB License Agreement on a permanent basis provided you transfer all copiesof the SOF TWARE and all written materials, and the recipient agrees to the terms of this Agreement. Youmay not modify, adapt, translate, reverse engineer, decompile, disassemble, or create derivative works basedon the SOFTWARE. You may not modify, adapt, translate or create derivative works based on the writtenmaterials.

LIMITED WARRANTY

• ABB AB’s entire liability and your exclusive remedy shall be, at ABBAB’s option, either (a) return of the price paid or (b) repair or replacement of the SOFTWARE that

does not meet ABB AB’s Limited Warranty and which is returned to ABBAB with a copy of your receipt. This Limited Warranty is void if failure of the SOFTWARE has

resulted from accident, abuse, or misapplication. Any replacement SOFTWARE will be warranted for theremainder of the original warranty period or 30 days, whichever is longer.

• ABB AB disclaims all other warranties, either express or implied, including but notlimited to implied warranties of merchantability and fitness for a particular purpose, with respect to theWARE, accompanying Product Manual(s) and written materials. This warranty gives you specific legal rights.

• Neither ABB AB nor anyone else who has been involved in the creation, production ordelivery of this product shall be liable for any direct, indirect, consequential or incidental damages (includingdamages for loss of business profits, business interruption, loss of business information, and the like) arisingout of the use or inability to use such product even if ABB AB has been advised of thepossibility of such damages. In any case, ABB AB's entire liability under any provisionof this agreement shall be limited to the amount actually paid by you for the software.

ACKNOWLEDGEMENT

By opening the diskette package you acknowledge that you have read this agreement, understand it, and agreeto be bound by its terms and conditions. You also agree that it is the complete and exclusive statement of theagreement between the parties and supersedes all proposals or prior agreement, oral or written, and any othercommunications between the parties relating to the subject matter of the licence or limited warranty.

This Agreement is governed in all aspects by Swedish law. If any provisions of this Agreement are invalid orunenforceable, all others will remain in effect.

IMPORTANT - READ CAREFULLY BEFORE OPENING

ABB Automation Products AB

1. Grant of License

2. Copyright

3. Term

4. Other Restrictions

Limited Warranty

Customer Remedies

No Other Warranties

No Liability forConsequential Damages

This legal document is an agreement between You, the user, and ABB Automation Products AB,Västerås, SWEDEN. By openingthe diskette package You indicate your acceptance of the terms and conditions of this agreement. If You do not agree to theterms of this agreement, promptly return the unopened diskette package and other items which are part of the product for a fullrefund. Your product is a single user version unless you have a written agreement with ABB AB.

License Agreement

• ABB Automation Products AB warrants that the software will perform substantially in accordance with theaccompanying Product Manual(s) for a period of 1 year from the date of delivery from ABB Automation ProductsAB, Västerås. ABB Automation Products AB does not warrant that the SOFTWARE is free from coding errors.

Automation Products

Automation ProductsAutomation Products

Automation Products

Automation Products

Automation Products AutomationProducts

Automation Products AutomationProducts

Automation Products

Automation ProductsAutomation Products

Automation ProductsSOFT-

Automation Products

ABB Automation Products ABSubstation Automation DivisionSE-721 59 VästeråsSwedenTel: +46 (0) 21 34 20 00Fax: +46 (0) 21 14 69 18

1MR

K51

108

6-U

EN

Printed on recycled and ecolabelled paper

Documents

User’s Manual CAP 535*1.1 Configuration, programming and ...€¦ · Table 2: Documents CAP 535 Document Number CAP 535 * 1.1 (This document) Configuration, programming and setting

User’s Manual CAP 5351.1 Configuration, programming and ...€¦ · Table 2: Documents CAP 535 Document Number CAP 535 1.1 (This document) Configuration, programming and setting