Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
User Manual
www.AvantcoEquipment.com 1
Gear Driven 30 Qt. Commercial Mixer
Models: MX30
Please read and keep these instructions. Indoor use only.
Shifting gears while this unit isrunning will void warranty.
01/2019
User Manual
User Manual
2 www.AvantcoEquipment.com
Index
Parts Overview .............................................................. 3
Standard Accessories .................................................... 4
Operation Instructions .................................................. 4
Figure 1: Gear Axle ........................................................ 5
Figure 2: Initiative Axle .................................................. 6
Figure 3: Fork ................................................................. 7
Figure 4: Change Speed Axle ........................................ 8
Figure 5: Turning Plate and Mixing Axle ....................... 9
Figure 6: Single Phase Motor Diagram ....................... 10
Figure 7: Center Axle ................................................... 11
Maintenance and Protection........................................ 12
Troubleshooting ........................................................... 13
Warranty Information ................................................... 14
User Manual
www.AvantcoEquipment.com 3
Parts Overview
8 5
&('1.%�����*34����4����� 3���
2
1
3
4
6
7
8
9
10
11
Top�cover
Gear�box
Safety�net(move)
Inner�gear
Turning�plate
Mixing�device I
Bowl
Stop�ring��52
1
1
1
1
1
1
1
1
1
1
1
5
Descviption Qty
12 Centre�axle
Fork
Bearing�6204
Key�5*20
Stop�switch
Change�speed�axle
Nameplate
1
1
1
1
1
1
1
1
1
1
1
Descviption Qty
Micro-switch
Micro-switch�shelves
Screw
Spring
Handle
Gasket
Screw
Arm
Copper��nut
Big�belt�wheel
1
1
1
2
2
2
1
1
1
1
1
Descviption Qty
Sleeve
Board
Gear�box�cover
Gear�axle
Initiative�axle
Motor
Stand
Back�board
Gasket
Small�taper�gear
Flange�knot
1
1
1
1
1
1
1
1
1
1
1
Descviption Qty Handwheel�axle
Key�5*15
Key�6*15
Handwheel
Handle�sleeve
Handle�axle
AC�contact�device
Seat
Bar
Back�cover
Capacitor
1
1
1
1
1
1
1
1
1
1
1
Descviption Qty
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Electric�box 156
Safety�net(fixedly)
Mixing�device II
Mixing�device III
Stop�ring��25
Big�taper�gear
Thread�bar
Start�switch
Micro-switch�shelves
&('1.%�����(�� �3�����3���
2
1
3
4
5
Initiative�axle
Key�6*28
1
1
2
1
1
Descviption Qty
Bearing�6204
Gasket
Bearing�6203
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
Description Description DescriptionDescription
Description
User Manual
4 www.AvantcoEquipment.com
1312
STANDARD ACCESSORIESFIGURE 10
NEMA 5015P110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
SPANISH:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
Operation Instructions
Standard Accessories
1312
STANDARD ACCESSORIESFIGURE 10
NEMA 5015P110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
SPANISH:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
1312
STANDARD ACCESSORIESFIGURE 10
NEMA 5015P110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
SPANISH:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
Item Description Qty 1 Flat Beater 1
2 Dough Hook 1
3 Wire Whip 1
4 Bowl 1
NOTES:
• Any agitator is easily installed by simply raising it onto the mixing axle, and the rotating it clockwise on the shaft until it locks into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate counter-clockwise and lower.
• All of the accessories are precisely fitted to the bowl, have rounded corners, and are easily removed for cleaning.
Please ensure that your power supply matches your machine
For changing the speed: Please stop machine first before changing speed in order to avoid damage to the gear box. Also make sure that the bowl is in fully lifted position and the guard is closed. • Slow Speed is the middle, dough hook setting. The knob will be facing forward. • Medium Speed is the bottom, flat beater setting. The knob will be straight down. • High Speed is the top, whisk setting. The knob will be straight up.
Mixing: Always use the correct attachment for the job.
A. Wire Whip: Suitable for mixing liquids and soft ingredients, can work in all speeds. Do not run for more than 15 minutes.
B. Flat Beater: Suitable for mixing dry ingredients, can work in low & medium speeds only. Do not use in high speed. Do not run for more than 15 minutes.
C. Dough Hook: Suitable for mixing dough, can work in low & medium speeds only. Do not use in high speed, do not run for more than 20 minutes. Absorption ratio must be more than 50%. Refer to mixer capacity chart.
!
!
1312
STANDARD ACCESSORIESFIGURE 10
NEMA 5015P110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
SPANISH:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
1312
STANDARD ACCESSORIESFIGURE 10
NEMA 5015P110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
SPANISH:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
1312
STANDARD ACCESSORIESFIGURE 10
NEMA 5015P110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
SPANISH:• Any agitator is easily installed by sim-ply raising it onto the mixing axle, andthe rotating it clockwise on the shaftuntil into place. To remove, raise theagitator on the shaft until it clears thelock and then rotate counter-clockwiseand lower.
• All of tools are precisely fitted to thebowl, rounded corners and easilyremovable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine firstbefore changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work within speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.B. Be suitable for mix and stir stuffing and raw material, andwork in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working timeis less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
User Manual
www.AvantcoEquipment.com 5
Mixer Capacity Chart Product Agitator and Speed
Maximum Bowl Capacity
Bread and Roll Dough -60 % AR Dough Hook - 1st only 25 lb.
Heavy Bread Dough -55% AR Dough Hook - 1st only 20 lb.
Pizza Dough, Thin -40% AR Dough Hook - 1st only 10 lb.
Pizza Dough, Medium -50% AR Dough Hook - 1st only 15 lb.
Pizza Dough, Thick -60% AR Dough Hook - 1st only 25 lb.
Raised Donut Dough -65% AR Dough Hook - 1st and 2nd 12.5 lb.
Mashed Potatoes Flat Beater 15 lb.
Waffle or Hot Cake Batter Flat Beater 10 qt.
Egg Whites Wire Whisk 1.5 qt.
Whipped Cream Wire Whisk 3 qt.
Cake Batter Flat Beater 20 lb.
When mixing dough ( pizza, bread or bagels), check your "AR" absorption ratio - water weight divided by flour weight. Above capacities based on 12% flour moisture at 70°F water temperature. If high gluten flour is used, reduce above dough batch size by 10%.
Example: If recipe calls for 5 lb. of water and 10 lb. of flour, then 5 divided by 10 = 0.50 x 100 = 50 %AR.
• 2nd Speed should never be used on mixtures with less than 50% AR.• Do not use attachments on hub while mixing.
When calculating the correct size mixer for your application, here are some helpful weights & measures:• 8.3 lb. = 1 gallon of water – 2.08 lb. = 1 Quart.
User Manual
6 www.AvantcoEquipment.com
GEAR AXLEFigure 1
6
&('1.%����#�� ��3���
2
3
4
5
6
7
8
9
10
11
Key�8*7*20
Bearing�6205
Bearing�ring
Gear
Gasket
Oil�seal�40*52*10
O�ring�30*1.8
1
1
1
1
1
1
1
1
1
1
1
1
QtyDescviption
7
&('1.%�����'�3 �3���
2
1
3
4
5
6
7
Gear�axle
Key�6*18
High-speed�gear
Sleeve
Low-speed�gear
1
1
2
1
1
1
1
Descviption Qty
Cover
Roller
Spring
Engager
Gear�ring
Dividing�ring
Gear
Above�bearing�ring
Joint
1
1
1
1
1
1
5
10
1
1
12
13
14
15
16
17
18
19
20
21
Key�8*7*45
Key�8*7*50
Centre�axle
Bearing�6206
Sleeve
Bearing�6203
Gasket
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
Description
User Manual
www.AvantcoEquipment.com 7
INITIATIVE AXLEFigure 2
8 5
&('1.%�����*34����4����� 3���
2
1
3
4
6
7
8
9
10
11
Top�cover
Gear�box
Safety�net(move)
Inner�gear
Turning�plate
Mixing�device I
Bowl
Stop�ring��52
1
1
1
1
1
1
1
1
1
1
1
5
Descviption Qty
12 Centre�axle
Fork
Bearing�6204
Key�5*20
Stop�switch
Change�speed�axle
Nameplate
1
1
1
1
1
1
1
1
1
1
1
Descviption Qty
Micro-switch
Micro-switch�shelves
Screw
Spring
Handle
Gasket
Screw
Arm
Copper��nut
Big�belt�wheel
1
1
1
2
2
2
1
1
1
1
1
Descviption Qty
Sleeve
Board
Gear�box�cover
Gear�axle
Initiative�axle
Motor
Stand
Back�board
Gasket
Small�taper�gear
Flange�knot
1
1
1
1
1
1
1
1
1
1
1
Descviption Qty Handwheel�axle
Key�5*15
Key�6*15
Handwheel
Handle�sleeve
Handle�axle
AC�contact�device
Seat
Bar
Back�cover
Capacitor
1
1
1
1
1
1
1
1
1
1
1
Descviption Qty
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Electric�box 156
Safety�net(fixedly)
Mixing�device II
Mixing�device III
Stop�ring��25
Big�taper�gear
Thread�bar
Start�switch
Micro-switch�shelves
&('1.%�����(�� �3�����3���
2
1
3
4
5
Initiative�axle
Key�6*28
1
1
2
1
1
Descviption Qty
Bearing�6204
Gasket
Bearing�6203
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
Description
User Manual
8 www.AvantcoEquipment.com
FORKFigure 3
9
&('1.%�����&� �
2
1
3
4
5
Fork axle
Nut
1
1
2Spring
2
Fork
2
QtyDescviption
4
"��� �/����3�����
When you are mixing, turn the head handle clock-
wise and lift up the bowl to the locking location. So,
it can make the mixing effect completely.
After mixing or changing an agitator, turn the
hand handle counterclockwise and lift down the
bowl so as to take off the bowl or agitator.
When you are installing an mixer, the mixing
axle must set in the faucet of mixer in order to p-
revent from taking off the agitator.
3
1
Shaft
3
1
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
Description
User Manual
www.AvantcoEquipment.com 9
CHANGE SPEED AXLEFigure 4
10
&('1.%����#�3���������3���
3
2
3
4
5
6
7
8
9
10
11
Handle�knot
Eccentricity�knot
Speed�block
O�ring�36.5*1.8
Spring
Stop�ring�20*1.2
O�ring�15*2.65
1
1
4
4
1
1
1
4
1
1
1
1
QtyDescviption
Pin�3*25
1
1
12
13
Handle
Screw�M6*10
Steel�ball
Change�speed�axle
Screw�M5*16
Before using, please check power supply if it match
your machine and be sure ground wire is eliable.
Before testing, please take mixing device off first, in
order to avoid damage machine which is match mo-
ving direction. It's necessary to change the three-ph-
ase machine if the moving direction is not match wi-
th arrow.
Mixing: according to the different mixing-material.
Choose the different mixing devices and speed.
A
B
C
,-%.!0(,+ (+/0.1#0(,+
For changing the speed: Please stop machine first
before change speed in order to aviod damage gear
box.OFF
A: Be suitable for mix and stir butter, eggs, and work wi-
th in high speed, working time is less than 15 minutes.
B. Be suitable for mix and stir stuffing and raw material,
and work in middle speed, working time is less than 20
minutes.
C: middle position is suitable for mixing dough,
working time is less than 30 minutes.Flour wat-
er quantity is 40%-50%.
100-120V
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
Description
User Manual
10 www.AvantcoEquipment.com
2
The machine must be put in the dry and flat ground, and make sure the machine steadily.
We can use four screws to fix the bracket, so the mixer will not shake or slope.
Check the power voltage is suitable for voltage of this mixer or not before using, the gr-
ound wire is firm whether or not.
When the motor of this machine is equipped with 380V, you can ask the professional el-
ectricians to fix the electrical source. If you find that running direction is not right, you
can change the two wires, besides the ground wire.
( ��3� �3���
Warning: users must install the shell ground wire.
&('1.%�����01.+(+'�-)!0%�!+$�*(2(+'�!2)%
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
Inner gear
Screw
Nut M14
Planetary gear
Bearing 6204
Turning plate
Spring gasket
Nut
Safe net
Bearing 6206
1
6
1
1
1
1
1
1
1
1
1
1
1
Gasket 14
Oil seal 35*56*12
Mixing axle 1
Spring gasket 14 1
3
4
5
6
1
2 7
8
9
11
12
13
10
14
16
15
16 Pin 10*37 1
Key 6*16
11
QtyDescviption
SPECIFICTION
Capacitor L�� ��
Power Supply V�� ��
Input Power W�� ��
Mixing
Speed
r.p.m�� ��
Type
30
1300
516
245
150
100-120~
B30FA
( ��3� �3����3�����4���4���
Maxflour Capacity(kg) 7
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )TURNING PLATE AND MIXING AXLEFigure 5
Description
User Manual
www.AvantcoEquipment.com 11
SINGLE PHASE MOTOR DIAGRAMFigure 6
&('1.%����/0!+$!.$�!##%//,.(%/
!+$�%)%#0.(#�$(!'.!*
2
1
3
4
Mixing device I
Bowl
1
1
1
1
1 2 3
4
12
Mixing device II
Mixing device III
Descviption Qty
1
The�B30FA food�mixer�is�the�new�product�of�RSK�series�of�Univ-
food�mixer.�It�can�mix,�grind�the�flour�and�liquid�food. The�desi-
is�with�belt�and�gear�transmission. The�mixer�makes�good�use�of
planet�principle,�so�the�agitator�runs�in�the�material�barrel�just�like
the�planet�and�it�can�mix�food�smoothly�and�fully. The�machine�runs
with�several�speeds�and�many�types�of�agitators��steadily�and�firmly,
the�customers�can�satisfy�with�it�according�to�different�requirements.
All�spare�parts�of�touching�food�are�stainless�steel�or�dealt�with�spec-
ial�operation,�and�they�can�measure�up�the�national�healthful standard.
This�machine�has�good�shape,�and�is�operated�simply.�Safety,�heal-
thful�and�high�efficiency,�it�is�suitable�for�hotels,�restaurants,�food�pr-
ocessing�factories�and�food�canteens.�It�also�can�be�used�for�the�medi-
cal�and�chemical�raw�material�factories.
You�use�and�maintain�the�mixer�correctly,�it�can�give�you�the�satisf-
ied�effect�for�a�long�time.
ersal
gn
( � ���4���
� -�3�� *��� ��3� 3
KT
1C 2C
K
N L
PE2
K4
K1
K1 overload protection switch
1C 2C AC contact device
K2 bowl lift switch
K3 safety protect switch
K4 urgency stop switch
K5 switch
K reactor
K0 fluctuate safety switch
KT time relay
CA/CB capacitor
M motor
��
M
K5 CA
K0
K2 K3
CB
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
177MX30SPECIFICATIONS
Type MX30
Capacity 30 QT.
Power Supply 110V
Phase 1
Input Power 1300W
Hertz 60 Hz
Horsepower 1 3/4 HP
Max. Flour Capacity 25 LB.
User Manual
12 www.AvantcoEquipment.com
CENTER AXLEFigure 7
6
&('1.%����#�� ��3���
2
3
4
5
6
7
8
9
10
11
Key�8*7*20
Bearing�6205
Bearing�ring
Gear
Gasket
Oil�seal�40*52*10
O�ring�30*1.8
1
1
1
1
1
1
1
1
1
1
1
1
QtyDescviption
7
&('1.%�����'�3 �3���
2
1
3
4
5
6
7
Gear�axle
Key�6*18
High-speed�gear
Sleeve
Low-speed�gear
1
1
2
1
1
1
1
Descviption Qty
Cover
Roller
Spring
Engager
Gear�ring
Dividing�ring
Gear
Above�bearing�ring
Joint
1
1
1
1
1
1
5
10
1
1
12
13
14
15
16
17
18
19
20
21
Key�8*7*45
Key�8*7*50
Centre�axle
Bearing�6206
Sleeve
Bearing�6203
Gasket
" � � & ! * ( 2 % . 1 / % . * ! + 1 ! ) " � � & ! * ( 2 % . 1 / % . * ! + 1 ! )
Description
User Manual
www.AvantcoEquipment.com 13
Troubleshooting Trouble Possible Causes Solution
The axles can’t work when operating the machine
Poor contact of the electrical equipment
Check the Plug
The mixing bowl is out of position Moving direction is not correct
Change
Leaks oil Sealing washer is damaged Change
Difficult to move the bowl up and down Slideway is rusted Clean the slideway and lubricate
The motor is overheated and speed is down
The voltage is not enough, or incorrect speed
Check the voltage or use lower speed
Noise and overheating Poor lubrication Add or change lubrication
Mixer touches bowl The mixing device or bowl de-formed
Repair or change the bowl or mixing device
User Manual
14 www.AvantcoEquipment.com
Limited 1 Year WarrantyAvantco warrants its equipment free from manufacturer defect and workmanship for a period of 1 Year from the original date of purchase. This limited warranty is non-transferable and valid to the original commercial purchaser only. Avantco equipment installed in/on a food truck or trailer will be limited to a period of 30 Days from the original date of purchase. Avantco reserves the right to approve or deny the repair or replacement of any part or repair request. Avantco does not warrant parts or accessories purchased independently from equipment.
Avantco shall bear the standard labor charge for each approved repair or replacement, to the extent such repair or replacement is performed within 50 miles of an authorized service agency, during regular (i.e. straight time) hours of operation. Avantco does not assume responsibility for travel exceeding 50 miles, or any works performed outside of regular hours of operation (i.e. overtime). Avantco reserves the right to approve or deny the repair or replacement of any part or repair request.
Avantco Limited Warranty Does NOT Cover:• Avantco equipment not purchased directly from an authorized dealer.• Installation of Avantco equipment in a non-commercial or residential setting.• Failure to install or use Avantco equipment under proper operating conditions and electrical requirements.• Avantco equipment purchased, installed, or used outside of the Continental United States.• Avantco equipment damage or failure due to improper installation, improper utility connection or supply, and issues resulting from improper ventilation or airflow.• Avantco equipment where the serial number plate has been removed or altered.• Avantco equipment that has not been used appropriately, or subject to misuse, neglect, abuse, accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, or an act of God.• Avantco equipment that has been altered, modified, or repaired by anyone other than an authorized service agency. Avantco shall not be held liable for any damages to any person or property which may result from the use of the equipment thereafter.• Parts deemed by Avantco to be categorized as normal wear and tear parts, such as light bulbs, gaskets, cooking grids and other wearable parts.
Prior to contacting your authorized service agency, locate the product serial number plate. See your Avantco Product Spec Sheet for additional information.
Proper installation, initial check out, air shutter adjustments, or normal maintenance such as lubrication, adjustment, or calibration of controls is the responsibility of the owner/user or installing contractor and is not covered by this warranty.
This states the exclusive remedy against Avantco relating to the product(s) whether in contract or in tort or under any other legal theory, and whether arising out of warranties, representations, instruction, installation, or defects from any cause. Avantco shall not be held liable whether in contract or in tort or under any other legal theory, for loss of revenue or profit, or for any substitute use or performance, or for incidental, indirect, special or consequential damages, or for any other loss or cost of similar type, including without limitation, losses or damages arising from food or product spoilage.