User Manual (Part 2)

5.8 GHz ExpansionHandset E580-2

For use with AT&T modelsE5860 • E5865 • E5900B • E5965C

ATT-580-2CIB-d2.qxd 1/17/2004 6:06 PM Page 1

Table of contents

Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp.,

licensed to Advanced American Telephones.

STOP! See pages 2-3for easy instructions.

You must charge batteries and register thehandset before use.

For customer service or productinformation, visit our web site at

www.telephones.att.comor call 1-800-222-3111.

Please also readImportant Product InformationEnclosed in product package.

Before you begin........................................1Parts checklist.............................................1Battery installation & charging ................2Registering the handset ............................3Belt clip & optional headset ....................4Quick reference guide..............................5

ATT-580-2CIB-d2.qxd 1/17/2004 6:06 PM Page 2

1

Before you begin

This cordless telephone operates withthe maximum power allowed by theFederal Communications Commission(FCC). Even so, the handset and basecan communicate over only a certaindistance — which can vary with thelocations of the base and handset, theweather, and the construction of yourhome or office. For best performance,keep the base antenna fully upright.

If you receive a call while you areout of range, the handset might notring — or if it does ring, the call mightnot connect when you press PHONE.Move closer to the base, then pressPHONE to answer the call.

If you move out of range during aphone conversation, you might hearnoise or interference. To improvereception, move closer to the base.

If you move out of range without pressing OFF, your phone will be left“off the hook.” To hang up properly,walk back toward the telephone base,periodically pressing OFF until the callis disconnected.

Parts checklistRemember to save your sales receipt and original packaging in case you ever need toship your telephone for warranty service. Check to make sure the telephone packageincludes the following:

Handset charger

Telephone handset

Poweradapter

Belt clip

Batteries

ATT-580-2CIB-d2.qxd 1/17/2004 6:06 PM Page 1

LOW BATTERY

REDIAL CID LOG2:10 PM

1

2

Battery installation & chargingAfter installation, place the handset in the charger and allow batteries to charge for 12hours before use. You can keep batteries charged by returning the handset to the chargerafter each use. When battery power is fully depleted, a full recharge takes about 8 hours.

Press coin into slot onbase of handset torelease latch, thenremove battery cover.

Insert suppliedbatteries.

Place handset in charger to chargefor 12 hours before first use.

Light remains on while batteries are charging.

Low battery indicatorReturn handset to charger to rechargewhen this symbol flashes. (Handsetwill beep when battery is low.)

Insert toptab first.

To replace battery cover

Press down toclick in place.

Plug power cord into jack on undersideof charger, then plug transformer intoelectrical outlet.

Caution: Use only the suppliedNiMH battery (80-5461-00-00) orAT&T model 2AA NiMH replace-ment battery (SKU 26820). Do notuse alkaline batteries.

ATT-580-2CIB-d2.qxd 1/17/2004 6:07 PM Page 2

3

Registering the handset

Before using your new handset, you must register it withthe base. During registration, you must enter the 15-digitID number of the telephone base. To find this number, goto the base, press MENU, scroll down to select DISPLAY

BASE ID, then press OK.

The handset provided with your telephone is automaticallyregistered as Handset 1. Additional handsets will beassigned numbers in the order they are registered (2, 3, 4,etc.) up to a maximum of eight.

Handset 1 Handset 2 Handset 3

MENU

CALLS LOGBASE SETTINGSDISPLAY BASE-ID

^ OK V

CALLS LOGBASE SETTINGSDISPLAY BASE-ID

^ OK V

123456789012345

OK

ATT-580-2CIB-d2.qxd 1/17/2004 6:08 PM Page 3

4

Belt clip & optional headsetInstall belt clip as shown below if desired.

For hands-free telephone conversations, you can use any industry standard 2.5 mmheadset (purchased separately). For best results use an AT&T 2.5 mm headset.

Snap belt clip into notches onside of handset. Rotate and pullto remove.

Plug 2.5 mm headsetinto jack on side ofhandset (beneathsmall rubber cap).

ATT-580-2CIB-d2.qxd 1/17/2004 6:08 PM Page 4

5

Quick reference guideFor complete instructions, please refer to the manual provided with your telephone.

NavKey

Press center button to display menus.Press NavKey buttons to navigatethrough menus. Press center button toselect menu item highlighted.

Speaker

Press to activate handset speaker-phone. Press again to switch call backto earpiece.

Softkeys

Press a softkey to select a menu item displayed just above the key.

Off/Cancel

During a call, press to hang up.

While using menus, press to cancel anoperation, back up to the previous menu,or exit the menu display.

Phone/Flash

Press to begin a call, then dial a number.

During a call, press to receive an incomingcall, if Call Waiting is activated.

Sound Select

Press to customize speaker sound forclear speakerphone conversations.

Intercom

Vibrate Ringer Control Ringers

Low Batt Tone Keypad Tone Range Tone

Appearance Set Time Contrast

Phone Setup Language Reset Settings

Directory Calls Log Pictures Sounds&Alerts Settings

Main menu

Sounds & Alerts menu Settings menu

Left Right

SelectUp

Down

ATT-580-2CIB-d2.qxd 1/17/2004 6:09 PM Page 5

Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 1.2 AT&T 1/19/04.

www.telephones.att.com

ATT-580-2CIB-d2.qxd 1/17/2004 6:09 PM Page 6