Upload
phamliem
View
229
Download
0
Embed Size (px)
Citation preview
Tips to help you
prevent false alarms:
BEFORE LEAVING THE
PROPERTY
Secure all windows and
doors confine pets to
designated rooms by
keeping doors shut
AT NIGHT
Keep windows and doors
shut in rooms which are
being protected by sensors
confine pets to designated
rooms
ENSURE
Sensors are not obstructed
by furniture or suspended
objects eg. Festive/party
decorations detectors are
free of insects and
cobwebs
TAKE CARE
Protect sensors when
decorating or doing
building work. If you go
away ensure that your key
holders know how to switch
your alarm off
HOW TO CANCEL FALSE
ALARMS
Your password/voice code
if ADT needs to verify an
alarm inform ADT Security
of the dates you’ll be away
Contact Us
131 005
www.adtsecurity.com.au
38 South Street,
Rydalmere NSW 2116
ARMING
• Ensure power is on and READY LED is on or flashing
• Enter 4- 6 digit code
QUICK ARM • Press On • ARM and EXIT LEDS come on
PARTIAL ARMING
• This is used when the user is INSIDE the premise
• and wants protection around the perimeter.
• Close all protected windows and doors.
• Ensure power is on and READY LED is on or flashing
• Press PARTIAL key (system arms with pre-programmed zones
bypassed)
• To QUICK ARM - Press PARTIAL
• ARM and EXIT LEDS come on
DISARMING • Enter 4 - 6 digit code
• Armed led turns off
RESETTING CODEPAD
• Arm the system and then disarm
RESETTING SMOKE DETECTORS • Press * 7
• If panel is still beeping, enter 4 - 6 digit code.
• Wait a few minutes and try again.
BYPASSING/ISOLATING • When bypassing, the system must be in DISARMED state.
• Press BYPASS
• Enter 4 - 6 digit code (bypass light flashes)
• Enter the zone you wish to bypass as a 2 digit number
• (i.e. zone 1 = 01, zone 2 = 02)
• Press BYPASS
• If you wish to bypass more than 1 zone,
• repeat the above 2 steps until all zones you want bypassed are
entered
User Guide for Das – NX4
Tips to help you
prevent false alarms:
BEFORE LEAVING THE
PROPERTY
Secure all windows and
doors confine pets to
designated rooms by
keeping doors shut
AT NIGHT
Keep windows and doors
shut in rooms which are
being protected by sensors
confine pets to designated
rooms
ENSURE
Sensors are not obstructed
by furniture or suspended
objects eg. Festive/party
decorations detectors are
free of insects and
cobwebs
TAKE CARE
Protect sensors when
decorating or doing
building work. If you go
away ensure that your key
holders know how to switch
your alarm off
HOW TO CANCEL FALSE
ALARMS
Your password/voice code
if ADT needs to verify an
alarm inform ADT Security
of the dates you’ll be away
Contact Us
131 005
www.adtsecurity.com.au
38 South Street,
Rydalmere NSW 2116
• Press BYPASS again OR # key to exit the bypass mode
• Then ARM as normal
• All bypasses are cleared when the system is disarmed or repeat
procedure
TESTING • If programmed for a battery test, communicator test, or siren test
• Press # 4 4
• The test will be performed as programmed
• If the siren test is performed, enter a user code to silence the siren
WALK TEST • Press * CHIME
• Enter Master Arm/Disarm Code
• Walk Test system, each zone makes a beep and latches in alarm
• When complete, DISARM system
CODEPAD TONES • Press * 0
• Press 1 to adjust higher and 2 to adjust lower
• Press # to exit
VIEW ALARM MEMORY • Press * 3
• Zones bypassed are on
• Those in alarm will flash
POF AND BOF INDICATORS • OF - LED Power light indicator will be on and steady if
• power is on to system. It will be off if no power
• BOF - LED Power light indicator will be flashing
• if Low system battery