USER GUIDE

Picture apliances ..................................................... 3

Before first use ........................................................ 4

Tips for saving electrict energy ................................ 6

Important warnings .................................................. 7

Installation and connection....................................... 8

Connection to the electricity grid ..............................9

Device operation .....................................................11

Maintenance and cleaning ......................................14

Troubleshooting ......................................................17

Picture appliances

Equipment apparatus can be changed depending on the model of the appliance.The label with basic information about the appliance is located in the interior or on the back of the device.

3

Before first use

Before plugging in electrical voltage, a machine is idle for approximately 12 hours.This reduces the possibility of improper action due to the impact of transport on cooling system.

Thoroughly clean the appliance, especially the interior(Follow advice from the chapter Cleaning).• Instructions for use are intended to,and describe the appliance and its correct and safeuse.• Remove the brackets and protectors of Styrofoam.• Remove all packaging materials and adhesive tape.• Before you remove the old cooling appliance, remove His neck, as this will prevent the children during the Game accidentally shut inside.

• The packaging of our products designed for the environment harmless material, which is without risk for the environment can be reprocessed (recycled) ordestroyed. In this regard, packaging materials adequately labeled.• Our guide was also printed on recycling paper, or on paper, without Bleached chlorine.• When the appliance is can not be used more when you spend a bothered, make sure not to be a burden environment.Provide the authorized collectors of waste household appliances (see Removing the old appliance).• served appliance immediately remove from service.

Unpacking

Our care for theenvironment

!

4

Possible to disable the lock To avoid the danger posed to children from choking.

• Appliances containing refrigerant and insulationingredients that require special degradation,thus removing appliances connect withauthorized and certified municipalcompany, or contact the dealer. becausethe risk of environmental pollution, be careful not to damage the pipe in the bottom of the apparatu.

Connect the appliance to the power grid• Insert the power cord -dovodnog cable into a grounded outlet, which must not be placed directlybehind the camera.• Make sure the unit is energized, and so to open the bottom cover under the door and make sure the display - a pointer electronic thermostat.

Set the to the desired location.

Note: The door may be about 2.5 cmmoved forward with respect to neighboringelements.

The thermostat for selection temperatureThe thermostat for temperature selection is factory regulated.The temperature will settle down after 24 hours.

Attention!

5

Tips for savingelectric energy

• Do not close the appliance door more frequently than necessary. This is especially important in hot or humid weather.

• Periodically check that the camera has secured a sufficient coolingdegree (smooth air circulation behind the appliance).

• Damaged or poorly attached to seal-magnetic rubber door causes a higher power, therefore, timely to make sure a suitable replacement.

• The condenser on the lower front side must always be clean and free of dust or layers of dust (see Cleaning the machine).

• Failure to comply with the instructions described in sections Position-ing and Saving energy can cause a higher power.

The symbol on the product or on its packaging indicates that the this product may not be treated as household waste. Instead it should be handed over to the appropri-ate collection centers for recycling electronic and elec-trical appliances. The correct bussing of this product will help prevent po-tential negative effects on the environment and human health, which could otherwise be caused by inappropri-ate waste handling of this product. For more detailed in-formation regarding the process, and re the use of this product, please contact your local office, your house-hold waste disposal or shop where you purchased the product.

6

Important warnings

The appliance is manufactured in compliance with all relevant security standards, butnevertheless do not recommend that adequate control using face impaired physical, motional, or mental abilities, or persons without the required knowledge or experience.• In accordance with the concern about preserving the environment, taking care not to damage the structure apparatus (or condenser tubes, for example, in transport the old appliance), or parts of the cooling system inside the appliance.• The appliance contains a refrigerant and oil, so remove the damaged machinecompliance with environmental requirements (see section Our concern for the envi-ronment).• If the mains supply cable el. Energy is damaged, to avoid danger must substitute manufacturer, its service agent, or qualified personnel.• The camera does not keep flammable, volatile or explosive substances, such as eg.explosives or sprays containing volatile solvent (such as butane,propane, pentane and the like). These sprays can be identified by the printed label content or symbol for flammability.• Bottles with high alcohol must be sealed and arranged in a vertical position.• Warning: Open for ventilation apparatus, must constantly be kept clean and unob-structed.• Warning: To defrost not use mechanical devices or other methodsother than those recommended by the manufacturer.• Warning: When installing, cleaning and removal of obsolete appliance, make surenot to damage the insulation or parts of the cooling system. This will preventenvironmental contamination.• Warning: The interior of the appliance do not use electrical appliances except those that the manufacturer of the appliance for cooling and freezing.

The appliance is properly connected to the power grid (refer to section Connection to the power network).Always unplug from the mains prior to repairs, before cleaning and be-fore replacing the light bulb.When switching off the machine, grasp the plug, and do not pull on the supply cable.

!

7

Installation and connection

proper functioning of the apparatus is conditioned by the performance (Class) of the appliance, which is indicated on the label with data on the appliance.

Unique Wine Cooler 400 is in CC5 Tropic this. class

Do not place the device near a heating and not ispostavljajte by direct sunlight rays. At short distances from the source heat, use the isolating plate.

The appliance must be set right, and steady to sufficiently hard surface. All models are equippedthe legs for easier leveling regulation appliance.

Classes Ambient temperatureN (normal) from +16°C to +32°CSB (subtropical) from + 16 ° C to + 38 ° CCC5 Tropic from +16°C to +42°C

Selection space

8

Levelling appliances

• Larger Phillips screwdriver or by hand from the outside Turn the legs and thereby raise or lower the machine and straighten it.

• Accurately determine the position of the camera, which should in vertically gently sloping to the back or front feet should be more twisted by approximately 1 cm from the last two legs and to showcase stands stable without swaying.

Setting up appliances

The front left leg

The front right leg

Rear Right holder

Last left holder

1. Lowering screwdriver turn right2. Lifting screwdriver turn left

9

Connecting toelectricity grid

The appliance plug in the mains connecting the supply cable. The wall socket must be Grounding (security socket). prescribed rated voltage and frequency are indicated on the label with basic data on the appliance.

Connecting to the power supply and grounding appli-ances must be made according to current standards and regulations. The device can withstand short du-ration voltage deviations, but only the most from -6 To + 6%.

If the voltage is not within the specified label with basic data on aparatu.-any defects caused by maladjusted voltage (not built-in correctors voltage) a malfunction outside the warranty period, and the same can be re-moved at the expense of the customer.

10

Device operation

RegulatingTemperature-thermostats

Dixell XR03CX

The temperature electronic display cases for drinks you can regulated between 2 ° C and 18-20 ° C. Showcase for drinking place in the room, where the temperature drops below 16 ° C or exceeds 42 ° C.

11

The screen display shows the actual temperature the temperature in the glass case on the first shelf. Actual temperature may differ from the selected, depending on thefrequency of opening the door of the wine, and ambient temperature.After a change of regulation, before the new changes wait 12 to 24 hours to reach Showcase regulated temperature.

Any change of preset temperature areas require intervention authorized service center or a professional person.Temperature can be adjusted between + 2 ° C up to + 14 ° Cwithout temperature ranges for cooling red wine.+ 2 ° C to + 4 ° C - white wine+ 4 ° C to 6 ° C sparkling wines+ 7 ° C to 9 ° C-liqueur wines+ 10 ° C to + 12 / + 14 ° C - rose wines

In the display cabinet by means of thermal Brass system controls the amount of moisture, the optimal amount of humidity for storing wine in the interval from 55% to 80%, which can be traced from the hydrometer, which is located on the first shelf.

Interior lighting provides better illumination of bottles and their labels, as well as better visibility of your collection of drinks.Interior lighting refrigerated cabinets is done blue LED, which has negative and adverse impact on the wine.

Key lighting is on the thermostat Dixell XR03CX left bottom row - just behind the label dixell.When you press the button again - the light is switched on, and when you press one more time, the light turns off.

Brightnessinterior and button

brightness

12

All shelves can draw, allowing easy stacking and extraction bottle. each shelf You can also remove and remove, allowingstacking larger bottles. Removing the shelf1. Remove the rack from the position STOP.2. Lift the second shelf goods up to shelves wheels come in an extended part of the guide, then pull out the drawer.

Putting shelvesThe side sills wheels retract into the guide and push the shelf in the interior, until they reach the shelf in its original position.

Before you start to lie bottles, check whether dials properly lie in the grooves. Several times pull the shelf outward to STOP position and push back in, whilewheels properly seated.

In each of the above 8 shelves can agree 9 bottles necks alternating front - rear. On the motionless bnoo showcases can agree about 33 bottles of wine portrait or landscape with necks alternating front - rear. The total capacity of the unit is approximately 105 bottles (0.75) l.

Do not let children climb, stand or hang on the shelves refrigerated cabinets, because they can be dangerous in injury, or damage the case. Fascia panels shelves are made of wood. Wooden parts are protected by foil, which remove. In use, fingerprints can leave stains on wood.

The structure and color of natural wood can bechange.

Make sure that the ventilation openings on the front of the chassis are not blocked. For optimum performance appliances at least once a year, or suck dust from the condenser. For free access to capacitors open the front cover on the front refrigeration cabinets, which attaches the upper side magnet.

Slide shelves

Stacking bottle

Tips for keeping

Wooden front panelshelf

13

Maintenance and cleaning

Fridge not have to dissolve, because the ice to block the evaporator dissolves automatically. The ice that formed on the evaporator block the action of the compressor in the period compressor standstill melt, and in the form of droplets collects in the evaporator below the aluminum body, and then through the opening in the vessel below the water to the evaporator copper pan at the bottom of the cabinet through which the pusher tube hot water controlled compressor which evaporates and increases the humidity in the cabinet. The humidity inside the cabinet is controlled by a hydrometer which is located on the top of the first shelf. The excess water, which can occur due to unforeseen disturbances user forgets to close the door / is still water in the pan on the compressor, which is volatile in atmosferu.Temperaturna areas and humidity is set default settings.

The exterior of appliancesPainted surfaces should be cleaned with a cloth and acleaning provided for wooden painted surfaces. For plastic and lacquered parts is not recommended to use abrasive or aggressive special funds, as for example. cleaning stainless pan.After cleaning, connect the appliance to the powernetwork, switch it up and re-fill it drink.

Before cleaning the appliances always disconnect electric energy in the machine!Do not use rough and aggressive cleaning agents that can be damaged surfaces to be cleaned.

Automatic defrost

Cleaning appliances

14

The interior of the appliances

The interior of the appliances with lukewarm water andsoap or baking soda and water. Never abrasive agents, solvents, polish or undiluted detergent. Once a year it is necessary to switch off the contours of moisture, dry and soft cloth smeared environmental oil for wooden surfaces.

Glass

Glass doors clean with glass cleaner or mild detergent and water and a soft cloth. not use abrasive cleaning powder.

Gasket doors

Plastic seal the door with a mild detergent and water or solvent as baking soda or mild powder for cleaning. Rinse well after cleaning grease seal gate thin film initials wax or petroleum jelly on the side of the hinge. this prevents adhesion or damage to seals.

Replacing the LED strip is a service procedure and working by an authorized service center. Before starting the replacement of the ice strip for lighting cut the power supply to the machine by pulling the plug from the outlet.

Changing LED strip lighting

15

In case of failure or power outage, the less open the door, to keep the temperature in interior. The gradual increase in temperature will not have negative impact on the beverage. If the weather is extremely hot, you can drink move to a cooler location while waiting to turn on the electric energy.

Nestanak struje

In the vicinity of appliances does not store or use gasoline or otherflammable substances.

16

Malfunction

The machine does not work when connected to theelectricity grid

cooling systemlong time workingconstantly

Water flows out of the appliance

Helpful hints

Make sure the plug is live and whether it ison (thermostat knob in the position of action).

• Too often open the door, or too longopen door.• Door not closed properly (maybe foreignbody between the door povješena door, Reviewseals, ...)• Complex larger quantity of hot drinks at once.• Due to insufficient cooling compressor andcapacitors: check the air circulation behindappliances and clean the condenser,behind the front bottom cover.

Water flows out of the appliance if the clogged outlet hole water, or if the melt water dripping next to the drain collecting water.• A clogged vent, clean, for example with plasticstraw.

The temperature is not low enough:• Is the temperature control is correct (seethe “management”)?• Is the thermometer correctly works?• Is the ventilation system working properly?• Is the appliance set up too close to a heat source?

Check

Troubleshooting

During the use of the appliance may appear less failures. Here are some of them, which often causes improper use, and you can remove yourself.

17

Malfunction

Noise and murmurs Cooling in the fridge-freezers allows the cooling system with compressor and fan, and this causes a certain height noise.The severity of noise depends on the situation and the proper the use of appliances.

• During operation of the compressor can be heard noise liquids, in the dormant heard streaming coolant. This is normal and does not affect the the life of appliances.• After turning on appliances and action compressor and streaming coolant may be somewhat louder. This is not a sign of failure and has no bearing on the life of the appliance.Over time, during the operation of appliances strength of these noise is significantly reduced.Sometimes, during the operation of appliances occurrence unusual or loud murmurs, for coffeeunusual. Such murmurs most commonly the resultirregular position of appliances:• The appliance must be placed gently sloping towards the back and steady without swaying on hard courts.• Do not touch the walls or adjacentelements.

Check

18

UNIQUE WINE COOLER

BRASS KOMERC d.o.o.Banja LukaAddress:Aleja svetog Save 4878000 Banja LukaBosna i Hercegovina

Telephone/fax:051 257 139

E-mail:brass@teol.net