Embed Size (px)
Citation preview
DIAGNOSTIC MODE
Diagnostic mode gives you the ability to trouble shoot the Vari-Slicer. Diagnostic mode is a series of manually operated independent tests which can be entered as follows.
With the power OFF, depress and hold the START and STOP buttons.
Turn the power ON while the above buttons are depressed.
Hold START and STOP buttons until the slice buttons begin to flash on and off.
Release all buttons and follow the next step quickly.
Within three seconds, while lights are still flashing, press and release the hidden button located to the left of the #1 button, you are now in Diagnostic Mode.
Select the specific tests using the numbered buttons. The START button must be pressed to initiate a particular test and should be pressed each time a new selection is made.
Turn the machine OFF for several seconds to reset it for normal operation.
TEST 1 : Jog Mode Test
The pusher can be moved to the left by pressing the START button or to the right by pressing the STOP button. If the "End Travel" or "Home" proximity sensor is made, the motor will stop immediately. This will indicate the proximity sensor is operating correctly. releasing the START or STOP button will allow the motor to be restarted.
TEST 2: Arm Test - (DOORS MUST BE CLOSED)
The gearmotor can be energized by pressing and holding the START button for three seconds. Continuing to hold the Start button for an additional three seconds will engage the arm clutch making the arm move down and up through a cycle. As long as the Start button is depressed the arm will continue to cycle every three seconds. During each of these cycles the input LED #I3 should go off and on once. If the LED remains either off or on then the "Knife Up" sensor must be adjusted so that the LED in on only when the arm is in the up position.
Rev. 10-1 -96
2003320005-6
MODEL 2003 VARIABLE THICKNESS BREAD SLICER
REPLACEMENT PARTS LIST
ITEM NO. PART DESCRIPTION
001 002 005 006 007 008 009 010 01 1 012 013 101 101 102 103 104 201 202 203 204 205 206 207 208 209 210 21 1 212 213 214 215 217 218 219 220 222 223 224 225 226 227 228 229 Rev. 06-1 0-99
Cover-Electrical Track-Crumb Tray Tray-Crum b Plate-Face Stop-Cover Bumper Frame-Main Spacer-Angle Angle-Table Support Bumper-Rubber Stiffener Motor-Brake 112 HP Motor-Brake 314 HP Key Sheave 3L, 2-Grooves 1.5 OD Belt-V 3L230 Block-Pivot Outside Bearing-Ball Ring-Retaining #N5000-137 Shaft-Drive Pulley-Timing Belt Sheave-3L, 2-Grooves 3.882 OD Ring-Retaining #5100-62 Side-RH Arm Side-LH Arm Spacer-Aluminum Tube Trunnion Flag Washer-Special Holddown Bearing-Bronze Flange Ring-Retaining #5100-50 Spring-Extension Belt-Timing 300L075 Spindle-Blade DiskICollar Washer-Special Knife-Scalloped Rod-Connecting Screw-Shoulder 112 X 1-114 Cover-Top Cover-Bottom Bearing-Bronze Thrust
PART NUMBER
2003-0021 2003-0038 2003-0037 2003-0003 2001-0111 2001-0112 2003-0001 2003-0034 2003-001 1 5902-0021 2003-0054 6301-3633 6301-561 1 4384-0406-1 5 2003-0070 5601-1 033 2001-0041 5250-0387 5840-1 026 2001-0047-1 2003-0044 2003-0071 5840-1 128 2003-0046-1 2003-0047 2003-0050 2003-0052 2003-0053 2003-0058 2003-0064 5254-31 90 5840-1 125 7021-4005 5601-3341 2001-0072-1 01 2001-0073-001 2001 -0074 71 07-7056 2003-0027 5842-8545 2003-0048 2003-0049 5254-3507
Parts List Continued
ITEM NO.
805 806 807 808 809 809 810 810 81 1 81 1 812 813 813 814 814 816 817 818 819 820 82 1 822 823 824 828 829 831 842 850' 858 858 859 875' 876 877 878 901 902 903 904*
MODEL 2003 VARIABLE THICKNESS BREAD SLICER
PART DESCRIPTION
Subpanel-Microprocessor Control-Microprocessor Supply-Power Potentiometer-5K (1 15 VAC only) Relay-4 Pole 3A (1 15 VAC) Relay-4 Pole 3A (230 VAC) Contactor-3 Pole (1 15 VAC) Contactor-3 Pole (230 VAC) Relay-Overload (1 15 VAC) Relay-Overload (230 VAC) Diode-Zener Varistor (1 15 VAC) Varistor (230 VAC) Suppressor-RC (1 15 VAC) Suppressor-RC (230 VAC) Plug-Screw Connector 8 Pin Plug-Screw Connector 10 Pin Plug-Screw Connector 4 Pin Socket-14 Pin Control-DC (1 15 VAC only) Resistor-Control (1 15VAC only) Din Rail Duct-Wire Cover-Wire Duct Block-Terminal Block-Ground Terminal Barrier-End Sensor-Prox. Harness-Switch W/O Switch Relay9 Pole (1 15 VAC) Relay9 Pole (230 VAC) Socket-8 Pin Harness-Main Cord-AC Motor Cord-Clutch Cord-Gearmotor Scanner-Bread Switch-Prox. (HomelEnd) Switch-Prox. (Door) Harness-Prox. Switches
PART NUMBER
2002-0002 5712-0402 5746-5687 5746-6000 5749-5624 5749-5666 5749-8274 5749-8284 5750-1252 5750-1254 5754-1 045 5754-1 070 5754-1 073 5754-1083 5754-1 084 5765-7468 5765-7469 5765-7467 5770-2834 6309-6000 6309-6014 5770-7166 5771-6260 5771 -6253 5770-7270 5770-7271 5770-7272 5757-8860 2003-0024-001 5749-5671 5749-5670 5770-2833 2003-0025-001 2003-0025-002 2003-0025-003 2003-0025-004 2003-0026-001 2003-0026-002 2003-0026-003 2003-0026-004
* Not Shown on Drawings
Rev. 10-31 -96
445 Sixth St., N.W., Grand Rapids, Michigan 49504-5298 (616) 45&7711 . 800125%3893. Fax: (616) 4565820
WARRANTY Varislicer TM Model 2003
Product Suitability This product is intended for the slicing of bread and bread related products only. The specific suitability for slicing certain bread types is to be determined at the time of sale in conjunction with an authorized Oliver Products Company representative.
Parts Oliver Products Company warrants that if any part of the equipment (other than a part not manufactured by Oliver) proves to be defective (as defined below) within 3 years afler shipment, and if Buyer returns the defective part to Oliver Products Company within one year, Freight Prepaid Oliver Products Company's plant in Grand Rapids, MI, then Oliver Products Company shall, at Oliver Product Company's option, either repair or replace the defective part, at Oliver Products Company's expense.
Labor Oliver Products Company further warrants that equipment properly installed, maintained, and cleaned in accordance with our special instructions, which proves to be defective in material or workmanship under normal use within 2 years from installation or actual shipment date, which ever comes first, will be repaired by Oliver Products Company or an Oliver Products Company Authorized Service Dealer, in accordance with Oliver Products Company's published Service Schedule.
For purposes of this warranty, a defective part or defective equipment is a part or equipment which is found by Oliver Products Company to have been defective in materials or workmanship, if the defect materially impairs the value of the equipment to Buyer. Oliver Products Company has no obligation as to parts or components not manufactured by Oliver Products Company, but Oliver Products Company assigns to Buyer any warranties made to Oliver Products Company by the manufacturer thereof.
This warranty does not apply to: 1. Damage caused by lack of cleaning, shipping, accident, misuse, or acts of God. 2. Damage resulting from improper installation or alteration. 3. Equipment not cleaned daily, misused, abused, altered, not maintained on a regular basis, operated
carelessly, or used in abnormal conditions. 4. Equipment used in conjunction with products of other manufacturers unless such use is approved by
Oliver Products Company in writing. 5. Normal wear parts including but not limited to: blades, belts, brakes, clutches. 6. Periodic maintenance of equipment and other adjustments required due to installation, set-up, or normal
wear. 7. Losses or damage resulting from malfunction.
THlS WARRANTY IS NOT EFFECTIVE UNLESS THE INSTALLATION/WARRANTY REGISTRATION HAS BEEN COMPLETED, SIGNED, AND RETURNED TO OLIVER PRODUCTS COMPANY WITHIN 15 DAYS FROM DATE OF INSTALLATION.
The foregoing warranty is in lieu of all other warranties expressed or implied AND OLIVER PRODUCTS COMPANY MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE REGARDING THE EQUIPMENT COVERED BY THlS WARRANTY. Oliver Products Company neither assumes nor authorizes any person to assume for it any other obligations or liability in connection with said equipment. OLIVER PRODUCTS COMPANY SHALL NOT BE LIABLE FOR LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
