UOP-Typical Equipment Layout Rev 01

Revision Indication

UOP LLC 25 East Algonquin Road Des Plaines, Illinois 60017-5017 USA

PROJECT SPECIFICATION

974901 999 SHEET 1

TYPICAL EQUIPMENT LAYOUT

999-301-1 999-5 Form QUA-04-5

Other specifications UOP Standard Specification: 9-51 referenced in this UOP Standard Drawing: specification: UOP Project Specification: 974901-112 UOP Drawing: GA30001-Rev-00

REV DATE BY APVD REV DATE BY APVD

0 10Jul13 AM PG 1 08NOV13 SM PKG

Not

e: T

he in

form

atio

n in

this

doc

umen

t is c

onfid

entia

l and

the

prop

erty

of U

OP

LL

C a

nd m

ust n

ot b

e di

sclo

sed

to o

ther

s or

repr

oduc

ed in

any

man

ner

or u

sed

for

any

purp

ose

wha

tsoe

ver

with

out i

ts w

ritt

en p

erm

issi

on.

Fixed-Bed Platforming Process Unit

974901 A typical equipment layout for this unit is shown on the following UOP Drawing: 974901-999-03-ga30001-Rev-00 Typical Equipment Layout CCR Platforming Process Unit

1. General Requirements

1.1 The Typical Equipment Layout is based upon UOP Standard Specification 9-51, Plot Plan

Design Criteria for Process Units. The priority for documentation interpretation is:

a. This Project Specification, including Section 3 Additional Requirements and Section 4 Guidelines. Unless noted otherwise, each point in the Additional Requirements section is mandatory and shall be incorporated into the final plot plan.

b. The suggested typical equipment arrangement shown on the UOP Typical

Equipment Layout Drawing.

c. The plot plan guidelines described in UOP Standard Specification 9-51. 1.2 The UOP Typical Equipment Layout drawing is a non-project specific, generic,

arrangement of the major process equipment typically included in this process. It is NOT intended to reflect the specific equipment used in, or the plot area available for, the subject process unit for any project. The drawing provides a suggested equipment layout that conforms to accepted good practice and incorporates the critical relationships between major equipment that affect process performance, as described in the Additional Requirements section of this specification.

1.3 There may be differences between the equipment required for this project and the

equipment shown on the UOP Typical Equipment Layout Drawing. The Contractor's plot plan shall incorporate the specific requirements (e.g., free draining, equipment relative locations) and equipment shown on the UOP Piping and Instrument Diagram and the UOP Project Specifications. UOP Project Specification 112 - Equipment List, indicates the specific equipment required for this project.

Revision Indication



974901 999 SHEET 2


999-301-1 999-5 Form QUA-04-5


0 10Jul13 AM PG

Not

e: T

he in

form

atio

n in

this

doc

umen

t is c

onfid

entia

l and

the

prop

erty

of U

OP

LL

C a

nd m

ust n

ot b

e di

sclo

sed

to o

ther

s or

repr

oduc

ed in

any

man

ner

or u

sed

for

any

purp

ose

wha

tsoe

ver

with

out i

ts w

ritt

en p

erm

issi

on.

2. Review of Contractors Plot Plan

2.1 UOP will perform a single review of the Contractors proposed plot plan. One copy of the

Contractor's first complete plot plan may be sent to UOP at the following address:

UOP LLC 25 East Algonquin Road Des Plaines, Illinois 60017-5017, USA Attention: Project Document Review Coordination (Bin A15)

2.2 The Contractor's plot plan shall be submitted in the English language, and early enough for

the Contractor to act upon UOP's comments without additional cost to the Owner. The plot plan drawing must be of good quality, suitable for microfilming. Transmittal letters accompanying the plot plan shall reference the UOP Project Number.

2.3 After receipt of the Contractor's plot plan, UOP will review the drawing(s) for process

related features. One copy, containing UOPs comments and marked "reviewed", will be returned.

3. Additional Requirements

The following points are mandatory and shall be incorporated into the final plot plan.

3.1 The Charge and Interheaters are a minimum distance from the reactors to minimize the

reactor circuit alloy piping requirements and compressor utilities. 3.2 The Combined Feed Exchanger should have a minimum pipe run into the Charge Heater.

3.3 The distance from the fired heaters to the Separator should be maximized for fire safety.

However, the linear (and equivalent) feet of the reactor circuit piping should be minimized to minimize compressor utilities.

3.4 The Separator and Recontact Drums should be located close to Net Gas Compressors.

4. Guidelines

The following points are guidelines and are to be considered during development of the final plot plan.

4.1 There should be access to the Reactor structures for catalyst loading using a crane.

4.2 The Debutanizer shall be located for best orientation relative to the reboiler fired heater

and the overhead air cooled condenser.

Revision Indication



974901 999 SHEET 3


999-301-1 999-5 Form QUA-04-5


0 10Jul13 AM PG

Not

e: T

he in

form

atio

n in

this

doc

umen

t is c

onfid

entia

l and

the

prop

erty

of U

OP

LL

C a

nd m

ust n

ot b

e di

sclo

sed

to o

ther

s or

repr

oduc

ed in

any

man

ner

or u

sed

for

any

purp

ose

wha

tsoe

ver

with

out i

ts w

ritt

en p

erm

issi

on.

4.3 It may be desirable to locate the chloride injection facilities near the edge of the plot if a dike will be required for containment of the organic chloride. Otherwise, the chloride and condensate injection facilities are located near the Combined Feed Exchanger to minimize the length of small diameter tubing. The requirements for the chloride storage drum are determined by the contractor according to the local codes.

4.4 It may be desirable to locate the sulfide injection facilities near the edge of the plot if a

dike will be required for containment of the organic sulfide. Otherwise, the sulfide injection facilities are located to minimize the length of small diameter tubing. The requirements for the sulfide storage drum are determined by the contractor according to local codes.

4.5 Similarly, it may be desirable to keep the caustic facilities near the edge of the plot area.

1. General Requirements1.1 The Typical Equipment Layout is based upon UOP Standard Specification 9-51, Plot Plan Design Criteria for Process Units. The priority for documentation interpretation is:a. This Project Specification, including Section 3 Additional Requirements and Section 4 Guidelines. Unless noted otherwise, each point in the Additional Requirements section is mandatory and shall be incorporated into the final plot plan.b. The suggested typical equipment arrangement shown on the UOP Typical Equipment Layout Drawing.c. The plot plan guidelines described in UOP Standard Specification 9-51.

1.2 The UOP Typical Equipment Layout drawing is a non-project specific, generic, arrangement of the major process equipment typically included in this process. It is NOT intended to reflect the specific equipment used in, or the plot area available f...1.3 There may be differences between the equipment required for this project and the equipment shown on the UOP Typical Equipment Layout Drawing. The Contractor's plot plan shall incorporate the specific requirements (e.g., free draining, equipment r...

2. Review of Contractors Plot Plan2.1 UOP will perform a single review of the Contractors proposed plot plan. One copy of the Contractor's first complete plot plan may be sent to UOP at the following address:2.2 The Contractor's plot plan shall be submitted in the English language, and early enough for the Contractor to act upon UOP's comments without additional cost to the Owner. The plot plan drawing must be of good quality, suitable for microfilming. ...2.3 After receipt of the Contractor's plot plan, UOP will review the drawing(s) for process related features. One copy, containing UOPs comments and marked "reviewed", will be returned.

3. Additional Requirements4. Guidelines

Documents

UOP-Typical Equipment Layout Rev 01