Smoke Detector Model NumberSystem Sensor

14002400

C2W-BAGE/Edwards

Max Number of Detectors/CircuitMax Number of C2M Series/Circuit

Legend: √ = CompatibleX = Not Compatible

Notes: (1) Must use specified base (do not substitute with System Sensor branded bases)(2) C2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (C2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit(5) EDWB110RLP and EDWB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector (does not apply to detectors employing plug-in bases) - DO NOT MIX TECHNOLOGIES

Compatibility Issues: 1. Is there a remote LED indicator?2. Does the smoke detector have a relay base?3. Check total number of detectors on a circuit does not exceed the recommended maximum.

1151¹1151¹1151¹2151¹2151¹2151¹1451¹1451¹1451¹1451¹2451¹2451¹2451¹2451¹

C2M-PD1²C2M-PDC³

C2M-PDHC³C2M-PDHRC³

Copyright © 2008 by Frank Kurz (All Rights Reserved)

EDWARDS/GE Panel Model Number 1527 2280Base

NA X XNA X X

EDWB110LP X XEDWB116LP(RLY) X X

EDWB110RLP X XEDWB110LP X X

EDWB116LP(RLY) X XEDWB110RLP X X

EDWB401B X XEDWB406B(RLY) X X

EDWB401BR X XEDWB406BR(RLY) X X

EDWB401B X XEDWB406B(RLY) X X

EDWB401BR X XEDWB406BR(RLY) X X

NA X X

NA √² √²NA X XNA X XNA X X

NA NA30 30

(1) Must use specified base (do not substitute with System Sensor branded bases)(2) C2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (C2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit(5) EDWB110RLP and EDWB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector (does not apply to detectors employing plug-in bases) - DO NOT MIX TECHNOLOGIES

2. Does the smoke detector have a relay base?3. Check total number of detectors on a circuit does not exceed the recommended maximum.

V = VERIFIEDNV = NONE VERIFIED

© 2008 by Frank Kurz (All Rights Reserved)

6601 6602/6604 6616/6632 EST1-1Z1 EST1-2Z3/2Z6

√ √ √ √ √X X X X X√ √ √ √ √X X √ X XX X X X X√ √ √ √ √X X √ X XX X X X X√ √ √ √ √X X √ X √X X X X XX X √ X √√ √ √ √ √X X √ X √X X √ X √X X X X XX X X X X

√ √ √ √ √

√³ √³ √³ √³ √³√³ √³ √³ √³ √³30 30 30 30 3030 30 30 30 30

(2) C2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (C2M-PDC has "Clean Me" technology and may NOT function with some panel models)

(6) Each detection circuit must employ a single model number of smoke detector (does not apply to detectors employing plug-in bases) - DO NOT MIX TECHNOLOGIES

√³ √³ √³ √³ √³

ESA 6500 8500 (IDC) 8500 (ZAM) 4 wire 8500 ESAC

√ X √⁴ √ √⁴X X X X X√ X √ √ √X X √ √ √√ √ X X X√ X √ √ √X X √ √ √√ √ X X XX X √ √ √X X √ X √√ √ X X X√ √ X X XX X √ √ √X X √ √ √X X X X √√ √ X X XX X X X X

√ √ √ √ √

√³ √³ √³ √³ √³X √³ √³ X √³

30 30 3030 30 30

√³ √³ √³ √³ √³

30⁴ 30⁴30⁴ 30⁴

IRC3 (ZB8)

X √ √ √X X X X√ √ √ √√ √ √ √X X X X√ √ √ √√ √ √ √X X X X√ √ √ √√ √ √ √X X X X√ √ √ X√ √ √ √√ √ √ √√ √ √ √X X X XX X X X

√ √ √ √

√³ √³ √³ √³√³ √³ √³ √³30 30 30 3030 30 30 30

IRC3 (RZB) NV IRC3 (SIGA-UM) V IRC 3 (SIGA-UM) NV

√³ √³ √³ √³

EST2 (SIGA-UM) EST3 (IDC) EST3 (SIGA-UM)

√ √ √X X X√ √ √√ √ √X X X√ √ √√ √ √X X X√ √ √√ √ √X X XX X X√ √ √√ √ √√ √ √X X XX X X

√ √ √X

√³ √³ X√³ √³ X30 30 3030 30 30

√³ √³

Mirtone Panel Model NumberSmoke Detector Model Number BaseSystem Sensor

1400 NA2400 NA

MTB110LPMTB116LP(RLY)

MTB110RLPMTB110LP

MTB116LP(RLY)MTB110RLP

MTB401BMTB406B(RLY)

MTB401BRMTB406BR(RLY)

MTB401BMTB406B(RLY)

MTB401BRMTB406BR(RLY)

C2W-BA NAGE/Mirtone

NANANANA

Max Number of Detectors/CircuitMax Number of CM2M Series/Circuit

Legend: √ = CompatibleX = Not Compatible

Notes: (1) Must use specified base (do not substitute with System Sensor branded bases)(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) MTB110RLP and MTB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector - DO NOT MIX TECHNOLOGIES and observe limit numbers.

Compatibility Issues: 1. Is there a remote LED indicator?2. Does the smoke detector have a relay base?3. Check total number of detectors on a circuit does not exceed the recommended maximum.4. In instances where there are NO detectors listed, the control panel must be changed and the entire fire alarm system verified.

1151¹1151¹1151¹2151¹2151¹2151¹1451¹1451¹1451¹1451¹2451¹2451¹2451¹2451¹

CM2M-PD1²CM2M-PDC³

CM2M-PDHC³CM2M-PDHRC³

Copyright © 2008 by Frank Kurz (All Rights Reserved)

7124 7200 7600 7800 7501

X √ √ √ √X X X X XX X X X XX X X X XX X X X √X X X X √X X X X XX X X X XX X X X √X X X X XX X X X XX X X X XX X X X √X X X X XX X X X XX X X X XX X X X X

X X X X √X X X XX X X X √³X X X X √³

NA 20 20 20 30NA NA NA NA 30

(1) Must use specified base (do not substitute with System Sensor branded bases)(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)

(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) MTB110RLP and MTB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector - DO NOT MIX TECHNOLOGIES and observe limit numbers.

3. Check total number of detectors on a circuit does not exceed the recommended maximum.4. In instances where there are NO detectors listed, the control panel must be changed and the entire fire alarm system verified.

√³

7502/7504 7516/7532 MIR1-1Z1 MIR1-2Z3/2Z6 FS-101

√ √ √ √ √⁴(30)X X X XX X X √ √⁴(30)X √ X X X√ √ X X X√ √ √ √ √⁴(25)X √ X X XX X X X X√ √ √ √ √⁴(30)X √ X √ XX X X X XX √ X X X√ √ √ √ √⁴(25)X X X X XX X X X XX X X X XX X X X X

√ √ √ √ √(42)

√³ √³ √³ √³ √³(42)√³ √³ √³ √³ √³(30)30 30 30 30 SPL⁴30 30 30 30 SPL⁴

(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)

√⁴(25)

√³ √³ √³ √³ √³(42)

FS-302 FS-502 FS-1004 M2000 MIR2 (GSA-UM)

√⁴(15) √⁴(15) √⁴(15) √ √√ X

√⁴(15) √⁴(15) √⁴(15) X √X X X X √X X X √ X

√⁴(12) √⁴(12) √⁴(12) √ √X X X X √X X X √ X

√⁴(15) √⁴(15) √⁴(15) X √X X X X √X X X √ XX X X √ X

√⁴(12) √⁴(12) √⁴(12) X √X X X X √X X X √ XX X X √ XX X X X X

√(21) √(21) √(21) √ √

√³(21) √³(21) √³(21) √³ √³√³(21) √³(21) √³(21) X √³SPL⁴ SPL⁴ SPL⁴ 30 30SPL⁴ SPL⁴ SPL⁴ 30 30

√⁴(12) √⁴(12) √⁴(12)

√³(21) √³(21) √³(21) √³ √³

790 (79045, 79045-2) 8000

√⁴ √X XX √X √X XX XX √X XX √X √X XX XX √X √X √X XX X

X √XX √³X √³

20 30NA 30

√³

Compatible Analog Loop DevicesMircom

MIX-1551AMIX-2551AMIX-1251A

MIX-2251A/2251TAMIX-2551TMA

MIX-7251AMIX-M500MAMIX-M501MA

MIX-1251BAMIX-2251BA

MIX-2251TMBAMIX-2251TBA

MIX-5251BAMIX-5251RBA

MIX-5251HAMIX-502MA

MIX-M500RAMIX-M500SA

MIX-M500DMASystem Sensor

5551A5551RA5251PA

5251RPAM500X

B524BIAB501B

IM-10ACR-6ASC-6A

FTX-P1AC2-6A

1251(B)2251/T

2551TM-R7251

M5251P/RPSmoke Detector Model NumberApollo

55000-22555000-325

HochikiDCD-135

DCD-135DCD-135DCD-190DCD-190DCD-190

SIJ-24SIJ-24SIJ-24

SLR-24SLR-24SLR-24

SLR-24HSLR-24HSLR-24HSLR-835SLR-835SLR-835

SLR-835B-2SLR-8354451HT

54515451

System Sensor14002400

1151A2151A

C2W-BAC2WT-BA

C2WTR-BA1451145124512451

1451DH2451-A

GE/Edwards6249C6250C6264C6266C6269C6270C

6269C-0036270C-003

Cerebrus Pyrotronics (Siemens)DI-2DI-3

Sentrol-ESL (GE)429C

429CT429CST429CRT

711U711U711U711U

713-5U713-5U713-5U713-5U

721U721U732U732U732U732U

Detection Systems Inc.DS250

DS250THDS282

DS282THMircom

MIR-525MIR-525T

MIR-1400AMIR-2400A

Mirtone7347173494735757349573495735957359573594734057359473405

C2M-PD1²

NapcoFW-2

Simplex/Grinnell (Tyco)2098-9110

FenwalPSD-7131PSD-7131PSD-7131PSD-7131PSD-7130PSD-7130PSD-7130PSD-7130PSD-7126PSD-7126PSD-7126PSD-7126PSD-7129PSD-7125PSD-7125PSD-7125PSD-7125CPD-7021CPD-7021CPD-7021CPD-7021

Max stand-by current of all detectors not to exceed 3mA

Legend: √ = CompatibleX = Not Compatible

Notes: (1) Must use specified base(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3

Compatibility Issues: Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.

Copyright © 2008 by Frank Kurz (All Rights Reserved)

Mircom Panel Model Number FX-2000 FA-300 FA-100

NA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X X

NA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X X

Base

NA √ √ √⁵NA √ √ √⁵

NS6-220 √ √ √⁶

NS4-220 √ √ √⁶HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶

HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶

HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶

HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶

HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶

HSC-220R √ √ √⁶NA √ √ √⁶

NS6-220 X X √⁶B401 X X √⁶

B401B X X √⁶B401 X X √⁶

NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √

X √ √B401B √ √ √B406B √ √ √B401B √ √ √B406B √ √ √

DH400A √ √ √DH400A √ √ √

NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √

NA √ √ √

NA √ √ XDB-3S √ √ √

NA X X √NA X X √NA X X √NA X X √

701E X X √701U X X √702E X X √702U X X √701E X X √701U X X √702E X X √702U X X √702E X X √702U X X √701E X X √701U X X √702E X X √702U X X √

NA X X √NA X X √NA X X √NA X X √

NA √ √ √NA √ √ √NA √ √ √NA √ √ √

NA √ √ XNA √ √ XNA √ √ X

73486 √ √ X73487 √ √ X73486 √ √ X73497 √ √ X73400 √ √ X73400 √ √ X73401 √ √ X73401 √ √ X

NA √ √ √

√ √ X

70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-000 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X

Max stand-by current of all detectors not to exceed 3mA

(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3

Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.

© 2008 by Frank Kurz (All Rights Reserved)

FA-200 FA-1000

X XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX X

X XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX X

√⁵ √⁵√⁵ √⁵

√⁶ √⁶

√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶

√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √

√ √√ √√ √√ √√ √√ √√ √√ √

√ √

X X√ √

√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √

√ √√ √√ √√ √

√ √√ √√ √√ √

X XX XX XX XX XX XX XX XX XX XX X

√ √

X X

X XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX X

(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)

Compatible Analog Loop DevicesSystem Sensor

2W-BA5551RA5251PA

5251RPAM500X

B524BIAB501B

IM-10ACR-6ASC-6A

FTX-P1AC2-6A

1251(B)2251/T

2551TM-R7251

M5251P/RPSmoke Detector Model NumberApollo

55000-22555000-325

HochikiDCD-135DCD-135DCD-135DCD-190DCD-190DCD-190

SIJ-24SIJ-24SIJ-24

SLR-24SLR-24SLR-24

SLR-24HSLR-24HSLR-24HSLR-835SLR-835SLR-835

SLR-835B-2SLR-8354451HT

54515451

System Sensor

14002400

1151A2151A

C2W-BAC2WT-BA

C2WTR-BA1451145124512451

1451DH2451-A

GE/Edwards6249C6250C6264C6266C6269C6270C

6269C-0036270C-003

C2M-PD1Cerebrus Pyrotronics (Siemens)

DI-2DI-3

Sentrol-ESL (GE)429C

429CT429CST429CRT

711U711U711U711U

713-5U713-5U713-5U713-5U

721U721U732U732U732U732U

Detection Systems Inc.DS250

DS250TH

DS282DS282TH

MircomMIR-525

MIR-525TMIR-1400AMIR-2400A

Mirtone7347173494735757349573495735957359573594734057359473405

NapcoFW-2

Simplex/Grinnell (Tyco)2098-9110

FenwalPSD-7131PSD-7131PSD-7131PSD-7131PSD-7130PSD-7130PSD-7130PSD-7130PSD-7126PSD-7126PSD-7126PSD-7126PSD-7129PSD-7125PSD-7125PSD-7125PSD-7125CPD-7021CPD-7021CPD-7021CPD-7021

Max stand-by current of all detectors not to exceed 3mA

Legend: √ = CompatibleX = Not Compatible

Notes: (1) Must use specified base(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3

Compatibility Issues: Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.

Copyright © 2008 by Frank Kurz (All Rights Reserved)

Notifier Panel Models AFP-200 AFP-300/400

NA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ X

Base

NA √ √NA √ √

NS6-220 √ √NS4-220 √ √

HSC-220R √ √NS6-220 √ √NS4-220 √ √

HSC-220R √ √NS6-220 √ √NS4-220 √ √

HSC-220R √ √NS6-220 √ √NS4-220 √ √

HSC-220R √ √NS6-220 √ √NS4-220 √ √

HSC-220R √ √NS6-220 √ √NS4-220 √ √

HSC-220R √ √NA √ √

NS6-220 X XB401 X X

B401B X XB401 X X

NA √ √NA √ √NA √ √NA √ √NA √ √NA √ √

X √B401B √ √B406B √ √B401B √ √B406B √ √

DH400A √ √DH400A √ √

NA X XNA √ √NA √ √NA √ √NA √ √NA √ √NA √ √NA √ √NA √ √

NA √ √DB-3S √ √

NA X XNA X XNA X XNA X X

701E X X701U X X702E X X702U X X701E X X701U X X702E X X702U X X702E X X702U X X701E X X701U X X702E X X702U X X

NA X XNA X X

NA X XNA X X

NA √ √NA √ √NA √ √NA √ √

NA √ √NA √ √NA √ √

73486 √ √73487 √ √73486 √ √73497 √ √73400 √ √73400 √ √73401 √ √73401 √ √

NA √ √

√ √

70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-000 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √

Max stand-by current of all detectors not to exceed 3mA

(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3

Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.

© 2008 by Frank Kurz (All Rights Reserved)

AFC-600/NFS-640 NFS2-640 NFS-320

X X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X X

√⁵ √⁵ √⁵√⁵ √⁵ √⁵

√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶

√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √

X X X√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √

X X X√ √ √

√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √

√ √ √√ √ √

√ √ √√ √ √

√ √ √√ √ √√ √ √√ √ √

X X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X X

√ √ √

X X X

X X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X X

(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)

NFS-3030 AM2020/AFP-1010 RP-1001 RP-1002

(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)

S500(TC-2/TC-4) S5000 (TCM-2/TCM-4) XP5-C FCM-1