Prwrilng Clun hlnldng ffjlw te tfw World

ULTRAPURE 0.5m Ceramic TwinUnder Sink City Water Filter

with pH NeutralisationInstallation Instruction & Product Manual

* I

Installation Diagram

1yWyZ

1 JJ ,

B3

..sal* 2

ILLParts

i Chroroe Faucet

a Housing

3 Bracket

4 Tee Piece

$ Mrristop Valve

e PLV

r Blue Tube

8 Screws

ft Red Clips

l/T SraKHdC&u

MchOfltMOH)

1QuHh f*Ca«*ctgf

*W V4' BMJtTuK

C0npf4?uOn r»\f»d VI'ÿH

Shut-ofl Voh*

OOUWJM***MOOPYÿ

A 1/4' blue tube connects the feed water valve to the Pre-Filter.

B 1/4" blw tube con nects the Pest Filter to the ch rome faucet

Cartridge Specifications

NSF Tested & Certified Cartridge0.5 micron absolute

Ceramic Outer ShellThe ceramic outer shell is made from Diatomaceous Earthformed from millions of microscopic silicone sheLis -compressed to give a 0,5 micron absolute rating toremove the finest sediment, bacteria and parasites.

Impregnated with silver ions, the ceramic media hasenhanced bacteriostatic and self sterilizing properties toinhibit bacteria growth,

Carbon Block Inner CoreThe carbon block inner core is tested to remove ChlorineChloramines, bad taste & odour, chemicals, pesticides &

Heavy Metals.

Capacity: 12 mouths/3000 litres*Flow Rate: 3.5 litres per minuteyuy

:.LT.IW \

,When fitting die ULTRAFURE 0.5 CeramicCartridge, always insert the top part withthe label “THIS WAY UP” as shown inIMAGE A

1

.

IMAGE A

Insert the top part of the cartridge as shownin IMAGE A, on the water filter base part asshown in IMAGE B correctly.m This will ensure that the water filter will workproperly and no leaks shall occur.

IMAGE B

How to Flush the Corosex pH Neutralising Cartridge

Please follow these IMPORTANT Steps below to ensure there will be notaste issues. So you will have the best tasting filtered water possible.

i. Unpack your new w ater filter

2. Connect your water filter as required - DO NOT TURN ON THE WATERYET.

3. Remove all water filtration cartridges from inside your water filterafter the Corosex pH Neutralising Cartridge.

Your Corosex pH Neutralising Cartridge is normally installed intopositions 1 or 2. (Take Care when you are removing the ceramiccartridge. Please treat it like an Egg).

4. Turn on the water filter and check for leaks and ensure all is connectedcorrecdy.

5. With the Corosex pH Neutralising Cartridge installedinside the water filter, with NO OTHER cartridgesinstalled after the cartridge, simply turn on the faucetand let it flush for at least 20 minutes. This water canhe collected for the plants if so desired.

6. After flushing water through the Corosex pHNeutralising Cartridge for 20 minutes, turn off thewrater supply and turn on the w ater filter faucet againto release any w ater pressure and drain.

7. Remove the housings for the cartridges you haveremoved and replace those cartridges into thepositions they w ere in.

8. Tighten all housings, turn the water supply back onand check for leaks.

9. Turn on water filter and flush full system for afurther 10 minutes.

10. After a further 12 hours turn on the faucet andflush the whole system for another 3 minutes, you aregood to use your water filter.

Installing Your ULTRAPURE 0.5m Ceramic WaterFiltration Cartridge

i. Clear any items out of the way to ensure you have a safe clear area to work,with no trip hazards or electricity that could create harm.

2. Turn off the water supply at the T-Piece up under the sink or the sink taps fora bench top model.

3. Turn on the faucet to release any water in the line which will remove thepressure on the water filter system.

4. Lay a towel down to soak up any excess water and to create a better surfaceto wrork from.

5. Once the pressure has vented from the system place the cartridge tool overthe housing for the cartridge you want to replace.

6. With the correct posture in mind as required, turn the housing anti clockwiseto crack the seal. Once the housing seal is loose you can simply unscrewr thehousing by hand. (The ceramic cartridges can crack so please treat them likeyou would an eggl.

7. Remove the housing and throw away the old cartridge. You can wrash out thehousing as required with 2 to 3 tablespoons of bleach or a sterilizer of yourchoice, flush well with water after doing so.

8. Remove the O-ring from the housing and wipe it clean, lightly lubricate theO-ring with silicon grease or olive oil. Replace the O-ring into the slot and pressinto place.

9. Insert the newr caruidge into the housing - For a under sink it says this wayup. - For a bench top water filter, the end with the hole which says this way upgoes dowrrL

10. Ensure the end of the ceramic cartridge with the open hole fits nicely intothe housing cap standpipe, tighten securely with the housing tool.

11. Ensure you dry the housing and area surrounding then turn on the watersupply slowly. Check for leaks, if no leaks the system is ready to move forwardhut if you detect a leak repeat from above and fix the leak.

12. Turn on the water supply and flush the cartridge for 10 to 15 minutes, thiswater may he used on the garden.

13. After a further 12 hours flush again for a further 3 minutes and the waterfilter is good to he used.

14. For a cartridge containing carbon it is normal to see blackish water at firsthut this will pass quite quickly, you may also find the first glasses of water maylook quite milky, this is only oxygen that is released from the carbon which isperfectly safe to drink and will subside after a few days.

15. If you do not use your water filter for 5 days it is recommended that waterhe run to waste for 2 to 3 minutes before drinking.

Extended Ceramic Cartridge Life

Depending on the amoimt of sediment in your water and ifyou have sediment protection in front of the ceramiccartridge.

If the water flow slows dow n, you can simply scrub theceramic cartridge under a running kitchen tap. Just use a

f NEW green scourer pad or similar. Gently scrub the ceramic" cartridge under running water which will remove the

sediment blocking the outside of the cartridge allowing afull flow again.

e*if

£

Always wash your hands before and after cleaning acartridge. Try not to touch the ceramic pan of the cartridgeat all times.

tsIlitWoU

IWebsite: www.mvwaterfiltEr.com.auEmail: i rrfbgflmywaterfi ltercom.au

Tel:1800 769 300

III

Changing Filters

System Description

Your filter Housing consists of two main parts:A. The Head or Cap - water flows in and out of this section.E. The Sump - this contains the Filter Cartridges and is designedto seal the cartridge at the top and the bottom. These tivo parts arecalled a Housing when connected together and will loe connectedto a bracket.

JV

Please be aware that there are a variety of filter connections and sizesavailable and it is important to ensure that your cartridge is of thecorrect length before commencing.Stop Cw

Turning Off the Water Supply

: bfecog}

PIHILA LMh]V+m

Trace the tubing from the filter inlet, until you locate the watersupply connection and turn off any Stop Cock, Isolation Tap orBah Valve located at this point, YOU DO NOT NEED TO TURN OFFTHE MAINS WATER TAP TO COMPLETE YOUR SERVICE, ff TT ISCONNECTED WITH ITS OWN ISOLATION VALVE.

W

Release the pressure from the system, by opening the filter tapon the sink to the on position, some water may come out initiaCythen the flow will stop. You can leave the filter tap open wMeservicing.

Undoing the Housings - Removing the Sump

Slide the plastic housing spanner over the bottom of thesump. It is best to lay the system down, this allows you toachieve a better grip. Loosen the sump by turning it in fromright to left (front view) this may require you to remove it fromthe wall if mounted. Lift the system up and off the bracket.

NOTE: The housings are iuT of water. Stand them upright afterloosening if working in the cupboard. It is advisable to lay thehousings down in the sink when opening the rest of the way toallow the water to drain out. Drain the housings and removethe cartridges.

* CLOSE3!? ,

A lot of newer system use a series of quick connect fitting that

OPENO-RING

Clean and inspect the Housings

Remove the rubber circular 0-rings from the Sump using a pointed object. Becareful not to pierce or cut the O-ring. Inspect the Housing for any fine lines orvisible crack. Check around the inside and outside at the bottom of theSump and threads of the Sump and the Cap/Head and the inlet and outlets. Ifamyfine cracks are visible replace the housing immediately

Rinse the housing and fill about 1/3 with water. Add 2 tablespoons of bleach andscrub inside with dishwashing brush. Rinse thoroughly with tap water beforemoving on to the O-ring replacement phase.

Important: Turn off the Water supply before attempting to open,Before commencing this operation. this ensure that you are able to turn off the water supply to thefiltration system anti that you are aware of the location of the mains water tap also in case you need toturn off the whole house supply in an emergency. It would he helpful to have a towel and sponge to mopup any small spills that may occuryou will require the housing spanner supplied with your system

Inspect and Reseat the O-Rings

If replacing (he existing O rings insert the new O ring. Hhot replacing, wipe the existing O ring clean and applya thin coating of food grade silicone lubicrant or clean Vaseline petroleum jelly.Reseat the O-ring bach into the Sump and press it into the groove. Ibis step is important to ensure properfilter seal Mahe sure the O ring is seated level in the groove by running )tjur finger around the top of the Oring.

NOTE: When opening the filter housing to change the cartridge, the O-ring may lift out of the housing and stickto the cap. O-rings are not all the same so they may not fit if the original housing was not supplied fcy MyWater Filter.

CAUTION: If the O-ring appears damaged or crimped it should he replaced at this time. Most manufacturersrecommend replacement every year.

Replacing the FiltersSingle Filters -ULTRAFLRI 0.5 CeramicTwin Filters - The Prer-filter is the first stage of the filtration process

The Post LLTRAPURE 0.5 Ceramic filter is the second-'last stage of the filtration processTriple Filters - The Prer-filter is the first stage of the filtration process

The Post ULTRAPURE 0.5 Ceramic filter is the secondThe Third Filter - last stage of the filtration process

ULTRAPURE O.oin Ceramic FilterThe ULTRAPURE Ceramic cartridge does not require replacement every year. Ifin a non-change cycle this filtercan be removed and scrubbed clean with a scotch-brite style nylon scourer or kitchen brush, (that has not beenin contact with food) Scrub while holding under cold running water until it is a clean off-white colour.Take care not to drop this filter, visually inspect the exterior to ensure there are nor fine cracks oipitted areas.It is recommended that this filter be replaced every 2 years under normal conditions. Longer periods can beobtained dependant upon conditions. If in doubt, contact the My Water Filter staff and they will be happy toaduse you. When replacing the filters including the ULTRAPURE Ceramic, ensure that they are placed in theSump so you can see the manufacturer's written label as you replace the Head.

Standard Pre-FiltersA standard pleated oipoly-spun sediment filter requires changing annually and cannot be scrubbed clean.The}' are unable to remove bacteria. My Water Filter recommends the ULTRAPURE Ceramic as a far superiorchoice.

Post FiltersRemove any plastic wraping from the cartridge and insert it into the housing sump. Screw the housing sumponto the cap and hand-tighten IX) NOT OVER-TIGHTEN. You can give it a small nudge with the plastic housingspanner to further tighten slightly. Over tightening causes the O rings to flatten and makes rescaling the unitmore difficult. When you first turn on the water you may see some gray/black colouring this is just the carbonfines, carbon dust and is completely non-toxic.

Turn Water On and Flush SystemTurn on the water supply slowly to allow (he housing to fill with water. Check for leaks. Let the system run fora few minutes to allow air to displace. Please note that the apperance of tiny air bubbles may appear in youwater for a few days after the cartridge change. These air bubbles may make the water appear milk}- but (heywill disperse from the glass and in no way affect the quality of your drinking water.

Ch-kikina WIHBT tsIhtWaU

IWebsite: v/ww.mywaterfilter.com.au

Email: infb@mywaterfilter.com.au

Tel:1800 769 300

III