UL TEST REPORT AND PROCEDURE - Microsoft...UL TEST REPORT AND PROCEDURE Standard: UL 60950-1, 2nd Edition, 2014-10-14 (Information Technology Equipment - Safety - Part 1: General Requirements)

Issue Date: 2016-08-12 Page 1 of 9 Report Reference # E476677-A3-UL

Copyright © 2016

UL TEST REPORT AND PROCEDURE

Standard: UL 60950-1, 2nd Edition, 2014-10-14 (Information Technology Equipment - Safety - Part 1: General Requirements)CAN/CSA C22.2 No. 60950-1-07, 2nd Edition, 2014-10 (Information Technology Equipment - Safety - Part 1: General Requirements)

Certification Type: ListingCCN: QQGQ, QQGQ7 (Power Supplies for Information Technology

Equipment Including Electrical Business Equipment)

Product: AC ADAPTERModel: XRN-069, XRN-068, XRN-067, XRN-066, XRN-065Rating: Input: 100-240 Vac, 50/60 Hz, 0.3A;

Output: 5.0Vdc, 2.1A.

Applicant Name and Address: SHENZHEN ANHAORUIHE ELECTRONICS CO LTD#2 BUILDING ANHAORUI INDUSTRIAL PARKJIANAN ROAD TANGWEIFUYONG TOWN BAOAN DISTRICTSHENZHENGUANGDONG 518103 CHINA

This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the above referenced Standards. The products have been found to comply with the requirements covering the category and the products are judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on such products which comply with this Test Report and any other applicable requirements of UL LLC ('UL') in accordance with the Follow-Up Service Agreement. Only those products which properly bear the UL Mark are considered as being covered by UL's Follow-Up Service under the indicated Test Procedure.

The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety.

Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL.

Prepared by: Alvin Peng Reviewed by: Glenn Liu

Created by UL Document Assembler 2016-08-18 05:01:32 -05:00

ACampbell

Typewritten Text

32118 - 2 Port 3.1A Wall Adapter

ACampbell

Highlight


Supporting DocumentationThe following documents located at the beginning of this Procedure supplement the requirements of this Test Report: A. Authorization - The Authorization page may include additional Factory Identification Code markings. B. Generic Inspection Instructions -

i. Part AC details important information which may be applicable to products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of this Test Report.

ii. Part AE details any requirements which may be applicable to all products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of each Test Report.

iii. Part AF details the requirements for the UL Certification Mark which is not controlled by the technical standard used to investigate these products. Products are permitted to bear only the Certification Mark(s) corresponding to the countries for which it is certified, as indicated in each Test Report.

Product DescriptionDirect-plug-in Adapter for ITE. All electrical components are mounted on a PWB and housed in a plastic enclosure.The enclosure is secured by ultrasonic weld.

Model DifferencesModels XRN-069, XRN-068, XRN-067, XRN-066, XRN-065 have same circuit diagram, input and output specifications and the same enclosure materials, only minor difference for the PWB layout and enclosure shape.

Technical Considerations Equipment mobility : direct plug-in Connection to the mains : pluggable A Operating condition : continuous Access location : operator accessible Over voltage category (OVC) : OVC II Mains supply tolerance (%) or absolute mains supply values : +10%, -10% (Declared by

manufacturer) Tested for IT power systems : No IT testing, phase-phase voltage (V) : N/A Class of equipment : Class II (double insulated) Considered current rating of protective device as part of the building installation (A) : 20 Pollution degree (PD) : PD 2 IP protection class : IP X0 Altitude of operation (m) : 2000 Altitude of test laboratory (m) : less than 2000 meters Mass of equipment (kg) : Aprox. 0.0486 The product was submitted and evaluated for use at the maximum ambient temperature (Tma)

permitted by the manufacturer’s specification of: 40 degree C



The means of connection to the mains supply is: Pluggable A (DPIU) The product is intended for use on the following power systems: TN The equipment disconnect device is considered to be: Plug The product was investigated to the following additional standards: The blade dimension was

evaluated to be complied with NEMA configurations in accordance with Wiring Devices -Dimensional Specifications, ANSI/NEMA WD6

The following accessible locations (with circuit/schematic designation) are within a limited current circuit: CY1 Secondary Pin

The following circuit locations (with circuit/schematic designation) were investigated as a limited power source (LPS): USB Output Terminal

The following are available from the Applicant upon request: Installation (Safety) Instructions / Manual

Additional InformationN/AAdditional StandardsThe product fulfills the requirements of: N/AMarkings and instructionsClause Title Marking or Instruction Details Power rating - Ratings

Ratings (voltage, frequency/dc, current)

Power rating -Company identification

Listee's or Recognized company's name, Trade Name, Trademark or File Number

Power rating -Model

Model Number

Power rating -Class II symbol

Symbol for Class II construction

(60417-2-IEC-5172)

LPS marking (Optional) "L.P.S", "LPS" or "Limited Power Source"

Marking for Fusing Resistor

Rated 2R/0.5W and located on or adjacent to Fusing Resistor (FR1).

Special Instructions to UL RepresentativeInspect the transformer(s) listed in Production-Line Testing Requirements (Electric Strength Test Special



Constructions) per AA1.1- (C). When the tests are conducted at other location, Inspect test record and specification sheet provided by the component manufacturer. Verify the specification sheet indicates 100% routine test specified in Production-Line Testing Requirements (Electric Strength Test Special Constructions) be conducted at the component manufacturer.

Production-Line Testing RequirementsElectric Strength Test Special Constructions - Refer to Generic Inspection Instructions, Part AC for further information.

Model ComponentRemovable

Parts Test probe locationV

rms V dcTest Time,

sAll models Transformer -- Primary pins to

secondary pins3000

4242 Minimum 1

Earthing Continuity Test Exemptions - This test is not required for the following models:All models in this report.

Electric Strength Test Exemptions - This test is not required for the following models:--

Electric Strength Test Component Exemptions - The following solid-state components may be disconnected from the remainder of the circuitry during the performance of this test:--

Sample and Test Specifics for Follow-Up Tests at UL

Model Component Material Test Sample(s) Test

Specifics -- -- -- -- -- --



1.5.1 TABLE: list of critical components PassObject/part or Description

Manufacturer/ trademark

type/model technical data Product Category CCN(s)

Required Marks of Conformity

Supplement ID

01. Label Interchangeable Interchangeable Minimum 80 degree C, suitable for enclosure

PGDQ2 or PGJI2 UL

01a. Label (Alternate) -- -- Laser engraved -- --02. Plastic Enclosure and plug holder

SABIC JAPAN L L C 945 (GG) Rated V-0, HWI=3, Minimum 1.5mm thickness, 120 degree C. Plastic enclosure secured together by ultra-sonic welding.

QMFZ2 UL (E161759)

03. Input blade -- -- Copper or Copper alloy, non-polarized (NEMA 1-15P configuration). Integrally melded onto plug holder, the perimeter of the face section from which the blade projection is minimum 5.1 mm from any point on either blade.

-- --

04. PWB Interchangeable Interchangeable V-1 or better, Minimum 130 degree C.

ZPMV2 UL

05. Fusible resistor (FR1)

KAIHUA INDUSTRIAL HONG KONG LTD

FKN-1/2W 2ohm, Min 0.5W FPEW2 UL (E341249)

06. Bridge Diode (DB1) -- -- Minimum 600 V, minimum 0.5A -- --07. Electrolytic Capacitor (C1, C2)

-- -- Rated C1:10uF, C2: 15uF. 400 V, minimum 105 degree C

-- --

08. Current Sensor Resistors (R5, R6)

-- -- Each Minimum 1.3 Ohm, minimum 1W.

-- --

09. Choke (L1) -- -- Color-ring type. Rated 330uH, tolerance 10%.

-- --

10. Choke (L2) -- -- Color-ring type. Rated 4.7uH, tolerance 10%.

-- --

11. Transformer (T1) SHENZHEN CITY FLAME ELECTRONICS TECH CO LTD

EE13-052101 Class B, see enclosure ID 4-01 for details.

-- -- 4-01



11-1. Transformer (T1)-insulation system

SHENZHEN CITY FLAME ELECTRONICS TECH CO LTD

TaYa 130-1 Class 130(B). OBJY2 UL (E477536)

11-2. Transformer (T1) -coil (primary)

Interchangeable Interchangeable Copper magnet wire wound concentrically on bobbin. Minimum 130 degree C.

OBMW2 UL

11-3. Transformer (T1) -Bobbin

CHANG CHUN PLASTICS CO LTD

T375J Phenolic, rated V-0, minimum. 150 degree C, minimum 0.75mm thickness.

QMFZ2 UL (E59481)

11-4. Transformer (T1) -Insulation Tape

JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO LTD

CT (b)(g), CT* (c)(g)

Minimum 130 degree C OANZ2 UL (E165111)

11-5. Transformer (T1) -Triple Insulation wire

TA YA ELECTRIC WIRE & CABLE CO LTD

TILW-B Minimum 130 degree C OBJT2 UL (E225803)

11-6. Transformer (T1) -Varnish

ELANTAS ELECTRICAL INSULATION ELANTAS PDG INC

468-2 (d) Minimum 130 degree C OBOR2 UL (E75225)

11-7. Transformer (T1) -Tubing

GREAT HOLDING INDUSTRIAL CO LTD

TFL Minimum 200 degree C. VW-1. YDPU2 UL

11-8. Transformer (T1) -Core

-- -- Ferrite. EE13.. -- --

12. PWM Control IC (U1) WUXI CHIP HOPE MICRO-ELECTRONICS LTD

LP3783 -- -- --

13. Secondary IC (U2) WUXI CHIP HOPE MICRO-ELECTRONICS LTD

LP3515 -- -- --

14. Y Cap (CY1) (Optional)

SHANTOU HIGH-NEW TECHNOLOGY DEVELOPMNT ZONE SONGTIAN ENTERPRISE CO

CD, CE Each Max.1000pF, Min.250 Vac, Min.125 degree C, Y1 type.

FOWX2 UL (E208107)



LTD15. Primary lead wire Interchangeable Interchangeable Minimum 24 AWG, minimum

300 V, minimum 105 degree C.AVLV2 UL

16. USB port Interchangeable Interchangeable Copper alloys housed by metal case and additionally supported by plastic rated minimum V-2.

QMFZ2 UL

17. Plastic insulation sheet (Between Pri. and Sec.) (For Models XRN-068, XRN-066)

KUNSHAN DOBESTY OPTOELECTRONIC MATERIALS CO LTD (E339070)

PC9842B Rated V-2 min, 80 degree C. Minimum 0.45 mm thickness.

QMFZ2 UL

18. Heat-shrinkable tube (on FR1 and internal wire)

Interchangeable Interchangeable Rated VW-1, minimum 300V, minimum 125 degree C.

YDPU2 UL

19. Heat-shrinkable tube (on Pri. Cap EC2) (Only for Model XRN-067)

Interchangeable Interchangeable Rated VW-1, minimum 300V, minimum 125 degree C.

YDPU2 UL



Enclosures

Type Supplement Id DescriptionPhotographs 3-01 Top Overview for XRN-069Photographs 3-02 Blade Overview for XRN-069Photographs 3-03 Output Overview for XRN-069Photographs 3-04 Internal Overview for XRN-069Photographs 3-05 PWB Bottom Side view for XRN-069Photographs 3-06 Blade Overview for XRN-068Photographs 3-07 Output Overview for XRN-068Photographs 3-08 Internal Overview for XRN-068Photographs 3-09 Component Side View for XRN-068Photographs 3-10 PWB Bottom Side View for XRN-068Photographs 3-11 Blade Overview for XRN-067Photographs 3-12 Output Overview for XRN-067Photographs 3-13 Internal Overview for XRN-067Photographs 3-14 Component Side View for XRN-067Photographs 3-15 PWB Bottom Side View for XRN-067Photographs 3-16 Blade Overview for XRN-066Photographs 3-17 Output Overview for XRN-066Photographs 3-18 Internal Overview for XRN-066Photographs 3-19 Component Side View for XRN-066Photographs 3-20 PWB Bottom Side View for XRN-066Photographs 3-21 Blade Overview for XRN-065Photographs 3-22 Output Overview for XRN-065Photographs 3-23 Component Side View for XRN-065Photographs 3-24 PWB Bottom Side View for XRN-065

Diagrams 4-01 T1 SpecSchematics + PWB 5-01 PWB Layout for XRN-069Schematics + PWB 5-02 PWB Layout for XRN-068Schematics + PWB 5-03 PWB Layout for XRN-067Schematics + PWB 5-04 PWB Layout for XRN-066Schematics + PWB 5-05 PWB Layout for XRN-065

Miscellaneous 7-01 Blade DimensionMiscellaneous 7-02 Enclosure Drawing (XRN-069)Miscellaneous 7-03 Enclosure Drawing (XRN-068)Miscellaneous 7-04 Enclosure Drawing (XRN-067)



Miscellaneous 7-05 Enclosure Drawing (XRN-066)Miscellaneous 7-06 Enclosure Drawing (XRN-065)Miscellaneous 7-07 Insulation Sheet Drawing Between Pri. and Sec.(XRN-066)Miscellaneous 7-08 Insulation Sheet Drawing Between Pri. and Sec.(XRN-068)


File E476677 PHO-01


File E476677 PHO-02


File E476677 PHO-03


File E476677 PHO-04


File E476677 PHO-05


File E476677 PHO-06


File E476677 PHO-07


File E476677 PHO-08


File E476677 PHO-09


File E476677 PHO-10


File E476677 PHO-11


File E476677 PHO-12


File E476677 PHO-13


File E476677 PHO-14


File E476677 PHO-15


File E476677 PHO-16


File E476677 PHO-17


File E476677 PHO-18


File E476677 PHO-19


File E476677 PHO-20


File E476677 PHO-21


File E476677 PHO-22


File E476677 PHO-23


File E476677 PHO-24


File E476677 DIA-01


File E476677 DIA-01


File E476677 SCH-01


File E476677 SCH-02


File E476677 SCH-03


File E476677 SCH-04


File E476677 SCH-05


File E476677 MIS-01


File E476677 MIS-02


File E476677 MIS-03


File E476677 MIS-04


File E476677 MIS-05


File E476677 MIS-06


File E476677 MIS-07


File E476677 MIS-08


Issue Date: 2016-08-12 Page 1 of 3 Report Reference # E476677-A3-ULTest Record

Test Record No. 1-- The manufacturer submitted representative production samples of AC ADAPTER, Models XRN-069, XRN-068, XRN-067, XRN-066 and XRN-065 for investigation.

-- Unless otherwise indicated in each test item of the datasheet, all tests were conducted on Models XRN-069, XRN-068, XRN-067, XRN-066 and XRN-065.

-- For the test WEIGHT AND MOMENT DETERMINATION: (DIRECT PLUG-IN UNIT) in the datasheet, conducted in accordance with UL1310 according UL 60950 PAG and indicated that the tests and evaluation are acceptable by UL1310 according UL 60950 PAG.

-- Any information and documentation involving UL Mark services are provided on behalf of Underwriters Laboratories Inc. (UL) or any authorized licensee of UL.



The following tests were conducted:Test Testing Location/CommentsEnd Product Reference PageGeneral GuidelinesPower Supply Reference PageInput: Single-Phase (1.6.2)Energy Hazard Measurements (2.1.1.5, 2.1.2, 1.2.8.10)SELV Reliability Test Including Hazardous Voltage Measurements (2.2.2, 2.2.3, 2.2.4, Part 22 6.1)Limited Current Circuit Measurement (2.4.1, 2.4.2)Limited Power Source Measurements (2.5)Humidity (2.9.1, 2.9.2, 5.2.2)Determination of Working Voltage; Working Voltage Measurement (2.10.2)Thin Sheet Material (2.10.5.9, 2.10.5.10, 2.10.5.6)Transformer and Wire /Insulation Electric Strength (2.10.5.13)Steady Force (4.2.1 - 4.2.4)Drop (4.2.6, 4.2.1)Stress Relief (4.2.7, 4.2.1)Direct Plug-In Equipment-Moment (4.3.6)Direct Plug-In Blade Securement (4.3.6)Direct Plug-In Security of Input Contacts (4.3.6)Direct Plug-In Resistance to Crushing (4.3.6)Direct Plug-In Rod Pressure (4.3.6)Direct Plug-In Input Blade Endurance (4.3.6)Heating (4.5.1, 1.4.12, 1.4.13)Ball Pressure (4.5.5, 4.5)Touch Current (Single-Phase; TN/TT System) (5.1, Annex D)Electric Strength (5.2.2)Component Failure (5.3.1, 5.3.4, 5.3.7)Power Supply Output Short-Circuit/Overload (5.3.7)

Test results are valid only for the tested equipment. These tests are considered representative of the products covered by this Test Report. The test methods and results of the above tests have been reviewed and found to be in accordance with the requirements in the Standard(s) referenced at the beginning of this Test Report.



The following tests were waived:Test Rationale for WaivingTransformer Abnormal Operation (5.3.3, 5.3.7b, Annex C.1) Covered by 5.3.7 Power Supply

Output Overload

The following supplements are provided as a part of this Test Record. NOTE: These supplements are only available to the Applicant via the CDA system.

Type Supplement Id DescriptionAttachment 2-01 CRDDatasheet 2-02 Test Datasheet


File E476677 01-ATT-01


File E476677 01-ATT-01


Documents

UL TEST REPORT AND PROCEDURE - Microsoft...UL TEST REPORT AND PROCEDURE Standard: UL 60950-1, 2nd Edition, 2014-10-14 (Information Technology Equipment - Safety - Part 1: General Requirements)