UG_BKM

NX5 Sheet Metal

Page 1 of 161

NX Sheet Metal

NX5 Sheet Metal

Page 2 of 161

Working in NX Sheet Metal

The NX Sheet Metal application provides a focused environment for the design of straight-brake sheet metal parts. Built on the industry-leading Solid Edge solution, NX Sheet Metal is intended for the designers of: machinery, enclosures, brake-press manufactured parts, and other parts with linear bend lines. It includes sheet metal-specific features such as flanges, tabs, jogs, corner conditions, and drawn cutouts, along with productivity enhancements such as automatic bend reliefs. The software also provides common modeling features typically used in sheet metal design, such as holes and slots, as well as other essential capabilities such as copy, paste, and mirror.

The application provides defaults for sheet-metal-specific properties such as material thickness, bend radius, and bend relief. You can easily change these defaults.

NX5 Sheet Metal

Page 3 of 161

Starting the application and setting preferences

Choose FileNew, and on the Model page, select the NX Sheet Metal template. The file opens in NX Sheet Metal.

In the application, you should see the NX Sheet Metal toolbar.

If you do not see it:

1. Choose ToolsCustomize. 2. On the Toolbars page, select the NX Sheet Metal box, then click Close.

Additional Modeling commands for creating sheet metal parts are available. If you do not see the following toolbars on your screen, follow step 1 above, and select the Form Feature and Feature Operation boxes.

NX Sheet Metal provides default values for typical sheet metal settings such as material thickness, bend allowance, bend radius, and neutral factor. You do not have to set them for each feature that you create. If you change them, they remain valid for all features in that part file. (You can override them in individual commands.)

To see what these settings are, choose PreferencesNX Sheet Metal. This brings up the NX Sheet Metal Preferences dialog, which includes those settings already mentioned, along with other bend options, and flat pattern settings.

For instructions on how to change these default values permanently, see Getting StartedCustomizing NXCustomer Defaults.

NX5 Sheet Metal

Page 4 of 161

Changing the defaults

You can change the sheet metal defaults for both global and command-specific parameters.

General: global parameters

Value Entry lets you choose from three methods for defining bends in your parts: a neutral factor, a bend table, or a bend formula (see details below).

o Neutral Factor Value (the default) refers to the neutral axisthe point in a bend where the tension of the outside of the bend and the compression of the inside become neutral. This neutral axis is used when figuring the bend allowance for flat patterns. It depends on the mechanical properties of the material being bent, and is represented by a percentage of the stock thickness, measured from the inside bend radius. The default value for this option is 0.33. You can supply a value between 0 and 1.

o Bend Table points to a table that specifies a neutral factor based on values from the bend region for angle, radius, and material thickness. You create this table in a specified format and place it in a default location.

o Bend Allowance Formula lets you supply values for the standard variables. The default formula is (Radius+(Thickness*0.44))*rad(Angle).

Material Selection provides access to a material table (also provided by you) that uses the material you select to provide the parameters for your bends. If you choose this option, the choices for Value Entry are not available.

Material Thickness: The default thickness for sheet metal parts. Bend Radius: The default radius for all bends (based on the minimum limit below which

cracking or splitting occurs). You may want to change this value, depending on the type of material you are working with.

Relief Depth and Width: Bending with a tight radius or with hard materials often results in burrs and fractures on the outside of the bends. Relief notches at the edges on the bend line address this problem. The depth and width options let you apply bend relief to the source face from which the flange is constructed, by specifying how far in from the edge of the face (D) and how wide (W) the reliefs extend.

If you do not want bend relief, select None.

NX5 Sheet Metal

Page 5 of 161

Flat Pattern Treatments Treatments for inside and outside corners: Chamfered or rounded corner treatments can be used to break the sharp corners.

Corner treatment options: Inside and outside corners can be chamfered or arced. In the latter case, you can supply a radius.

Flat pattern simplify: Flat patterns created from a cylindrical face or a cutout placed across bend lines create a B-spline curve. This option converts B-spline curves to simple lines and arcs. You can specify the minimum arc and deviational tolerance for the simplified curve.

Remove system-generated bend reliefs: When you create a closed corner with no relief or when you have a bend section that is inset into the base planar region without a relief, the software creates a very small bend relief or rip in the 3-D model to separate the sides of the bend section from the inset area. This option specifies that you want to remove those small bend reliefs or rips when the flat pattern is created. The following graphics highlight these reliefs.

NX5 Sheet Metal

Page 6 of 161

Maintain holes for deformed flanges: Flattening contour flanges on curved edges stretches the flanges. Holes created across bend regions in these areas are by default deformed splines. If you want the holes to be circular, select this option.

Flat Pattern Display You can specify which entities you want displayed on your flat pattern, on which layer, and how you want those entities represented: color, line type, and line width. For example, in the following flat pattern, bend centerlines are shown in blue dashed lines, bend tangent lines in phantom red, interior features in orange-yellow, and the exterior in black.

Default callouts for sheet metal features can be displayed on your flat pattern, and you can customize those labels as well.

You can establish defaults for command-specific parameters, such as Dimple, Taper Angle, or Bead Profile Type.

To access the forms for changing these defaults, choose FileUtilitiesCustomer Defaults. From the applications list, choose NX Sheet Metal.

For more detailed instructions on changing customer defaults, see Getting StartedCustomizing NXCustomer Defaults.

NX5 Sheet Metal

Page 7 of 161

Typical sheet metal workflow

In a typical NX Sheet Metal workflow, you:

1. Set the default values for sheet metal properties. (See Changing the Defaults for more information.)

2. Sketch the shape of the base feature, or use an existing sketch/section.

3. Construct the base feature, which is normally a tab, but which can also be a contour flange or a lofted flange.

4. Add features, such as flanges, jogs, and bends to further define the basic shape of the formed sheet metal part.

5. Apply unbends to flatten the bend areas where needed, and place holes, cutouts, embosses, or louver-type features on the part.

6. Rebend flattened bend areas to complete the part.

7. Create a flat pattern of the part for drafting and later manufacturing.

Constructing a base feature The typical workflow for construction of a sheet metal part begins with a base feature that typically defines the part's shape. In NX Sheet Metal, you normally start with a tab, but you can also use a contour flange or a lofted flange. The Tab command allows you to construct a flat feature of any shape using a closed profile.

Adding features After you have constructed the base feature, you can use the commands on the NX Sheet Metal and Form Features toolbars to complete the part by adding flanges, jogs, bends, cutouts, holes, pockets, and so on.

NX5 Sheet Metal

Page 8 of 161

Creating a flat pattern

You use Flat Solid to create a new solid body in the part file while keeping the original (parent).

The flattened body (and flat pattern) are always at the end of at the timestamp order. Every time a new feature is added onto the parent body, the flattened body is placed at the end. It updates to reflect changes in the parent.

Model History

Fixed Datum Plane (0)Fixed Datum Axis (1) Fixed Datum Axis (2) SB Tab (3) Extrude (4) SB Bend (5) SB Bend (6) SB Bend (7) SB Bend (8) Extrude (9)

NX5 Sheet Metal

Page 9 of 161

SB Flat Solid (10) Flat Pattern (11)

You then use Flat Pattern to create a sheet metal flat pattern for export to a machine tool for manufacturing. This step supplements Flat Solid by including extra entities such as bend centerlines, tangent lines, and other attributes that provide special machine instructions. You use Customer Defaults to specify which entities you want represented, and how you want them annotated.

NX5 Sheet Metal

Page 10 of 161

Creating sheet metal parts and features

The NX Sheet Metal toolbar has a button for each sheet metal feature. Picking the button for the feature brings up a dialog box that contains all the options and functions necessary to create it, just as in any other NX application.

Feature groupings Certain features within NX Sheet Metal have been grouped together under a drop-down list. For example, the bending features have been grouped together, as have the punching features. If you do not see a feature that you were expecting to see on the toolbar, check the drop down groups by clicking the little black triangle next to a feature button. Clicking this button exposes the rest of the features grouped with the feature shown on the toolbar.

Internal sketches Most NX Sheet Metal features include an underlying sketch that defines the feature geometry. This works as it does in Modeling, with the Extrude feature, for example. As a result, the majority of features ask you either to select a section (curve) or to sketch one.

For more information on these sketch options, see Using Sketches in NX Sheet Metal.

Dynamic interaction model Other interface characteristics should be very familiar to NX users: items such as dialogs, drag handles, and value entry boxes behave in NX Sheet Metal just as they do in the rest of the software, conforming to the dynamic interaction workflows available in NX.

NX5 Sheet Metal

Page 11 of 161

Instancing with sheet metal features

Instancing with NX Sheet Metal features takes one more step than instancing of general Modeling features. To use multiple features for an instance set, first place the features in a feature group in the Feature Set dialog box. Choose FormatGroup Features to start the Feature Set dialog box. Once you place the feature in a group, you can apply a rectangular or circular instance to the feature group. Neither mirroring, nor Modeling features requires this step. For an illustration of how to use these capabilities, see Using instancing with punch-type features.

NX5 Sheet Metal

Page 12 of 161

Using sketches in NX Sheet Metal

Many features in NX Sheet Metal use sketches as part of their construction geometry. In most cases, you can either use a pre-existing sketch or create one within the feature itself. It is important to understand the differences between these two methods, and how to use and access sketches within NX Sheet Metal features.

Sketch buttons in the dialog boxes In the dialog for each sketch-based feature, you see two icons that can be used for sketches. The

Sketch Section button lets you create a new sketch as part of the feature. The Curve

button lets you select a previously-created sketch from the graphics window to use as the feature contour.

Internal and external sketches Choosing between an internal and external sketch for a feature depends on whether you plan to reuse the sketch for other features. A sketch created from within a feature becomes part of it and is not available for use by other features. The feature that contains the sketch is the only one shown in the feature tree, and you must edit that feature to have access to the sketch. In the following figure, the Tab feature is based on an internal sketch, which is therefore not visible in the feature tree.

Model History Datum Coordinate System (0) SB Tab (1)

If you need to use the same sketch to construct multiple features, create the sketch using the Sketcher alone, and then select the pre-existing sketch when you create your feature. This keeps the original sketch in the feature tree, and it can be referenced by other features, as shown in the following figure.

Model History Datum Coordinate System (0) Sketch (1) SKETCH_000 SB Tab (2)

You can also convert an internal sketch to an internal one. In the Part Navigator, pick the feature that contains the sketch, press the right mouse button and select Make Sketch External from the menu.

NX5 Sheet Metal

Page 13 of 161

Bend parameters for sheet metal features

Many NX Sheet Metal features have standard bend parameter options:

Radius: the inside radius of the bend. Angle is the bend angle for the feature. The value must be greater than zero and less

than 180 degrees.

Bend Relief specifies whether to apply bend relief to the source face from which the feature is constructed. You can choose square or round reliefs that define the shape of the relief's interior corners. You can also specify no relief.

Extend Relief determines whether to extend the bend relief to the edge of the part. Bend Relief Depth and Width specify width and depth of the reliefs.

NX5 Sheet Metal

Page 14 of 161

Neutral Factor is based on a calculation of the neutral axis (the point in a bend where the tension of the outside of the bend and the compression of the inside become neutral). This value is always a percentage of the material thickness as measured from the inside radius of a bend region. It can range from 0 to 1, and the default is 0.33.

Corner Relief specifies that you want to apply corner relief to features that are adjacent to the feature you're constructing.

You can chose no relief, as illustrated in the following figure.

If you do set this option, you specify how you want the corner relief applied. Bend Only applies relief only to the bend portion of the adjacent features.

Bend / Face applies relief to both the bend and face portions of the adjacent features.

NX5 Sheet Metal

Page 15 of 161

Bend / Face Chain applies relief to the entire chain of bends and faces of the adjacent features.

NX5 Sheet Metal

Page 16 of 161

Controlling bend deformation

NX Sheet Metal lets you define deformation in bend regions using the following methods.

Select a material from the material file. Define a bend allowance formula. Use a table of bend parameters. Enter the neutral factor.

You can also override any of these methods by using Resize Neutral Factor on a specific bend region.

NX5 Sheet Metal

Page 17 of 161

Using a material table

One way to define the deformation in the bend regions of your part is to define a set of materials that include the bend parameter information.

To define the characteristics of the materials you can use, you must edit the sheet_metal_material_table.txt file. This file is usually in the %UGII_BASE_DIR%\ugii\materials directory. You can change the location of this file to another local directory or to a location in Teamcenter by changing the customer defaults for Sheet MetalGeneral on the Material Standards tab.

The materials file is a simple text file in the format of a standard comma-delimited spreadsheet. The material table is segmented from the rest of the file by a set of specific keywords: MATERIAL_TABLE and END_OF_MATERIAL_TABLE. Between these keywords is the data comprising the table.

The characteristics of the table are as follows:

The first row of the table contains the column headings. Each column must have a unique name that is one word long. (The underscore character

can be used to combine words.)

The keywords BEND_RADIUS, THICKNESS, and NEUTRAL_FACTOR are valid NX Sheet Metal feature parameters

The second row of the table is a flag indicating whether the information in that column is shown or hidden. (If a column is tagged as hidden, the data in that column does not appear in the NX Sheet Metal Material Standards dialog box and cannot be used in selecting the material.) Also, in the second row of the table, one column has a unique tag, which tells NX that the data in that column must be unique and will be used to tell one material from another even if the material parameters are the same. The column with the material names is usually labeled unique, although a different column could be unique (for example, a column of material ID numbers) as long as each string in the column is unique.

In the material table, the first column is a set of unique names that describe each material in the table. Each column after that contains information about the material, such as finish, thickness, default bend radius, and neutral factor.

Sometimes several versions of the same material may be required. In such cases, the information in the table can be exactly the same, except for the value in question and different identifiers in the unique column. For example, if you have a specific type of aluminum that you use (Aluminum 0421) but in several different thicknesses, your table might look something like this:

MATERIAL_TABLE

Material_name THICKNESS BEND_RADIUS NEUTRAL_FACTOR

unique show show show

Aluminum0421_T020 0.20 3.0 0.33

Aluminum0421_T030 0.30 3.0 0.33

Aluminum0421_T040 0.40 3.0 0.33

Aluminum0421_T050 0.50 3.0 0.33

NX5 Sheet Metal

Page 18 of 161

Aluminum0421_T060 0.60 3.0 0.33

END_OF_MATERIAL_TABLE Each row of data is given a unique identifier and the value in question changes, but everything else in the table can be static.

NX5 Sheet Metal

Page 19 of 161

Select a material

To select a material:

1. Choose PreferencesNX Sheet MetalPart Properties. 2. Under Parameter Entry, select Material Selection.

3. Click on Select Material to open the NX Sheet Metal Material Standards dialog box.

4. Use any of the displayed material parameters to filter the list of available materials. As you select options in the filters above, the materials available below are filtered. For example, if you select 3.6 for your thickness, you will only see materials with a thickness of 3.6 in the Available Materials window. You can always select any material in the Available Materials window by double-clicking it. The material then appears in the Selected Material window.

5. Click OK to select that material and its associated part parameters.

If your selections filter the Available Materials list until only one material is available, NX automatically selects that material. Confirm this by clicking OK. To change one of your selections, choose the filter option that is all dashes to clear out that filter selection and start again.

After you click OK, you are returned to the preferences dialog box, and your material is shown next to Select Material.

NX5 Sheet Metal

Page 20 of 161

Using Bend Tables

You can also control the deformation of bend regions with a bend table. Bend table data is stored in the same file as the materials data. The bend table data is a 3-dimensional table set and is segmented from the rest of the data in the file by TABLE and END_OF_TABLE tags. More than one type of table is allowed in this file, so to create a bend table, the TABLE tag must be followed on the next line by the NAME,BEND_TABLE key set. This tells NX that the set of tables in this block comprise a bend table as opposed to another type of table.

The 3D table set consists of any number of pages, each containing one standard 2D table. Immediately after the NAME line is a line showing the inputs of each 2D table. The inputs for a bend table are the thickness, bend radius, and angle. The order of these parameters is invariable, so the inputs line should state: INPUTS,THICKNESS,BEND_RADIUS,ANGLE. Pages are segmented from one another with the PAGE and END_OF_PAGE tags.

The format looks something like this: TABLE

NAME,BEND_TABLE

INPUTS,THICKNESS,BEND_RADIUS,ANGLE

PAGE

(2D table data)

END_OF_PAGE

PAGE

(2D table data)

END_OF_PAGE

END_OF_TABLE

Each 2D table has a format conforming to the list of inputs in the header of the TABLE block. The first input signifies the value in the first column, the second input is the values in the first row, and the third input is a single value in the position of column 1, row 1.

ANGLE BEND RADIUS

THICKNESS

Table data (returned values)

NX5 Sheet Metal

Page 21 of 161

So, for example, in the table below a bend region with an angle of 60, a radius of 3.0, and a part thickness of 2.0 would be assigned a neutral factor of 0.43.

60 1.0 2.0 3.0

1.0 0.43 0.44 0.45

2.0 0.41 0.42 0.43

3.0 0.39 0.40 0.41

If NX does not find a value in the table, it tries to interpolate a value using surrounding values. If this is not possible, NX either assigns default parameters or returns an error message. The value returned from the bend table is the Neutral Factor for the bend region in question.

You can change the Neutral Factor value by changing the parameters of the bend region, but the value will revert to the table-driven or material-driven value during an update, if you choose one of those methods of bend definition. To override a material, or table-driven

value, use Resize Neutral Factor .

NX5 Sheet Metal

Page 22 of 161

Neutral Factor and Bend Allowance Formula

Whenever a material is bent, the material compresses inside the bend region and stretches on the outside. The Neutral Factor is based on a calculation of the neutral axis (the point in a bend where the tension of the outside of the bend and the compression of the inside become neutral). This value is always a percentage of the material thickness as measured from the inside radius of a bend region.

You could also say that the Neutral Factor is the percentage through the material where the length of the surface in the flat state is equal to the arc length of the surface in the bent state.

Since you usually design parts in NX Sheet Metal in the bent state, the Neutral Factorin conjunction with the bend allowance formulais used to calculate the length of the bend region in the flat state. This happens, for example, when you use Unbend or Flat Pattern.

The Neutral Factor in NX Sheet Metal is part of an internal bend allowance formula, as follows:

Neutral Surface Length = rad(Angle) * (Radius + (Neutral Factor * Material Thickness))

You can also use other bend allowance formulas in NX Sheet Metal. You can define your own formula in NX Sheet Metal Preferences so that the bend region deformation is calculated using your formula rather than the default.

NX5 Sheet Metal

Page 23 of 161

Tab

Overview How To Options

Tab constructs a flat feature on a sheet metal part. You can use this command to construct a base feature or to add material to existing faces of a sheet metal part.

NX5 Sheet Metal

Page 24 of 161

Create a tab


To create a Base Tab:

1. Click Tab . If there are no other bodies in the part file, Base Tab is selected by default.

2. Define the profile plane.

3. Draw a closed profile , or select a section from an existing sketch.

4. Pick the side of the profile you want the material to be on: accept the default (above the profile) or double-click on the drag handle to reverse the direction.

5. Accept the default thickness for the tab, or specify another. (In the latter case, deselect Use Global Value.) Here, we specify thickness of 1 mm.

6. Click OK to finish the feature.

To create a secondary tab:

1. Click Tab. . If you have already created a base feature, Secondary Tab is selected by default.

2. Define the profile plane by selecting a part face.

3. Draw an open profile in any 2D shape. If the ends of the open profile sketch are not coincident with the edges of the part, they will be extended to those edges. An arc with open ends is extended to form a circle.


The tab is assigned the material thickness of the part.

NX5 Sheet Metal

Page 25 of 161

Tab options


The following options are available for Tab:

Base Tab and Secondary Tab let you specify which kind of tab to create. If there is no body in the part file, the system defaults to construction of a base feature. If there is already a body in the part file, the system defaults to creating a secondary feature.

Curve and Sketch Section let you specify whether to construct the feature from an existing sketch or to create a new sketch from within the feature. For more information on these sketch options, see Using Sketches in NX Sheet Metal.

NX5 Sheet Metal

Page 26 of 161

Flange


With Flange, you can quickly construct simple bent or "flanged" areas. A flange consists of a cylindrical region known as the "bend" region, and a rectangular region known as the "web." Flange also has options for an offset, which creates an extension of the base feature to which the flange is attached. You can set the radius and angle of the flange and specify options for the flange width, the inset distance, and the length of the web area. You can also control the sketch that is used to define the shape of the web portion of the flange.

NX5 Sheet Metal

Page 27 of 161

Create a flange


1. Click Flange .

2. Select the edge to which you want to add a flange . If you select the top edge, the flange defaults to up, as shown; if you select the bottom edge, the flange points down. To reverse the direction, double-click on the length drag handle, or click Reverse

Direction .

3. Define the flange length: pull the up arrow (L in the figure) to the desired length, or enter

the length in the input field.

4. Set flange angle (A) and offset (O), or accept the defaults.

5. Select flange options, if any.

6. Click OK to finish the flange.

You can create more complex flanges by editing the flange profile:

1. Follow steps 1 and 5 above.

2. Under Section, click Edit Sketch.

3. Draw the new profile and trim the old one. Make sure that you have a closed profile.

NX5 Sheet Metal

Page 28 of 161

4. Click OK to complete the feature.

NX5 Sheet Metal

Page 29 of 161

Flange options


Width lets you specify how you want the flange width to be measured.

Full Width Constructs the flange along the full width of the edge you select.

At Center

Constructs a flange that is centered on the edge you select. You can edit the dimensional value of the flange width and the flange remains centered. The default width is one third the length of the edge you select.

At End Constructs the flange starting at the end you select.

From Both

Ends

Constructs the flange width using dimensions from both ends of the edge you select. The default width is one-third of the edge width.

From End

Constructs the flange using a dimension from the end of the edge you select.

Flange Properties

Length Specifies the flange length. You can supply a value, an expression, a reference, and so on.

Reverse

Direction Changes the flange direction (from down to up or vice versa).

Angle Specifies the angle of the flange in relation to the base part.

Length Reference

Specifies how the web length is measured.

Inside Dimension measures the flange from the inside of the existing material.

Outside Dimension measures from the outside.

Inset

Specifies how far the flange is inset into the base part.

Material Inside : The flange is inset into the base material such that the outside face of the web area is flush with the selected edge.

NX5 Sheet Metal

Page 30 of 161

Material Outside : The flange is inset into the base material such that the inside face of the web area is flush with the selected edge.

Bend Outside : Material is added to the selected edge to form the flange.

Offset creates an extension of the base feature to which the flange is attached. You have the usual options for supplying a value.

Reverse

Direction Changes the direction off the offset, that is, converts the extension to a reduction (negative value).

You can also modify the default bend parameters and Preview the result.

NX5 Sheet Metal

Page 31 of 161

Contour Flange

Overview How To Options Related Topics

Contour Flange constructs a flange with several contours by extruding a profile that represents its cross section.

You can use Contour Flange as the base feature of a new sheet metal part or to add a feature to an existing one. Using Contour Flange, you can construct one or more bends at any angle. With the Chain Extent option, the flange chains itself around multiple selected edges and has options for mitered corners between the different flange sections.

You don't have to draw the arcs at each bend location. Bends are added automatically using the default bend radius. You can see this in the part and profile shown above.

If you want to use a different bend radius value, draw arcs in the profile, or change the default bend radius.

You can also use Contour Flange to create wrapped features.

NX5 Sheet Metal

Page 32 of 161

Create a contour flange


To create a Base Contour Flange:

1. Click Contour Flange . Base Contour Flange is selected by default if there are no sheet metal features in the part file. If there are, Contour Flange defaults to the secondary option.


3. Draw an open profile, and select it when prompted to select section geometry.

4. Specify part thickness or accept the default.

5. Specify the width of the feature.

6. Choose options.

7. Click OK to complete the feature. The arcs at each bend location are added automatically when you finish the profile, unless you have sketched arcs in the bend areas.

To add a contour flange to a sheet metal part (that is, create a Secondary Contour Flange):

1. Click Contour Flange .

Secondary Contour Flange is selected by default because there is already a body in the part file.

NX5 Sheet Metal

Page 33 of 161

2. Select an existing section or click Sketch Section and select a part edge. The plane on which you draw the profile must be normal to the part edge to which you are attaching the contour flange.

3. Draw an open profile. It must be coincident with a part edge.

4. Choose options in the dialog box, if any.

5. Specify the width of the flange.

NX5 Sheet Metal

Page 34 of 161


Tips and techniques for contour flanges

You can only apply bend reliefs with Contour Flange when the bend section actually intersects the original edge on which you placed the flange. The figure below illustrates this. Bend relief 5 mm wide and 5 mm deep was selected for both contour flanges. Note that only the flange with the bend positioned at the edge has bend relief.

NX5 Sheet Metal

Page 35 of 161

If the underlying sketch for Contour Flange intersects the part with an arc section, the

arc must be tangent to the top or bottom face of the part where it intersects the placement edge.

Any arcs that define the outer face of a bend region must have a radius greater than the part thickness.

Certain contour flange profiles produce error conditions: o The following graphic shows an invalid three-point arc for a secondary contour

flange. The problem is that the tangent line that is connected to the edge lies within the plane of the face of that edge

o The following profile, which consists of a combination of lines and arcs, does not

maintain tangent continuity at the intersection of the arc and line.

NX5 Sheet Metal

Page 36 of 161

When creating contour flanges on curved edges, create the profile at the end of the

curved edge for most predictable results.

NX5 Sheet Metal

Page 37 of 161

Contour Flange options


Width

Width Option

Finite Extent projects the profile a finite width to either side of the profile plane. You must supply a width.

Symmetric Extent applies half the specified width to each side of the profile. You must supply a

width.

To End Extent projects the profile to the end of the selected edge.

Chain Extent projects the contour flange along a series of edges that you select. Note that it will not chain through edges that meet at a concave corner. The following figure illustrates this. If chaining continued and included the edge where the contour flange is missing, it would self-intersect at the interior corner, causing an error condition.

Width: Specify a width (Finite and Symmetric Extent only)

Miter: You can set the following options for both the Start and Finish End of the contour flange

NX5 Sheet Metal

Page 38 of 161

Miter Corners

MIters (trims diagonally) the end at the angle you specify. Here is a flange mitered at the standard -45 degree angle.

Cutout

Normal to Thickness Face miters the end of the contour flange perpendicular to the thickness face.

Normal to Source Face miters the end of the contour flange perpendicular to the source face.

Angle sets the miter angle for the specified end of the contour flange. A negative value miters the flange inward and typically removes material. A positive value miters the flange outward and typically adds material. With some complex contour flanges, material can be both added or removed when an end is mitered.

Miter Using Normal Cutout Method

Creates miters perpendicular to the thickness face at corners and ensures that you can unbend and rebend the contour flanges in your part. Note that this method removes more material at the corners, so if you want water-tight flanges at the corners and are not concerned about creating a flat pattern of this part, you may prefer not to use this option.

Miter Interior Corners When Necessary

(Chain Extent only) Determines whether a miter should be applied, and only comes into effect when the chain edges of a contour flange span a bend region. This option for Contour Flange in NX 5 results from the new ability to flange around curved edges. To achieve behavior equivalent to NX 4, you must select only the tab edges and not the bend edges, as shown in the following figure.

In NX 5, if you select the bend edges, the Contour Flange is built across those edges as well. If the radius of the bend region being spanned is large enough, the Contour Flange fills in this

NX5 Sheet Metal

Page 39 of 161

area with a rounded bend region, as shown below.

If you select Miter Interior Corners When Necessary, the software only miters the corners spanning bend regions if the corners would self-intersect. In the figure below, the bend region on the left is too small to accommodate the flange edges, so they are mitered. The bend on the right is large enough that it isn't necessary.

The decision to miter or not is based on the length of the flange and the radius of the bend region being spanned. If the length of the flange is less than the radius of the bend region that the chain is traversing, NX Sheet Metal does not apply miters to that corner region. The radii in question are shown below highlighted in red.

NX5 Sheet Metal

Page 40 of 161

If you do not select this option, NX Sheet Metal miters the sides of the flanges, regardless of the length of the flange or the radius of the bend region being spanned, as shown in the following figures.

Corners

Close Corner

Specifies that you want to close the interior corners. Bend relief is applied when you close three inside bend corners. The following treatment options are only available if you select Close

NX5 Sheet Metal

Page 41 of 161

Corner.

Open applies no treatment.

Close closes the bent faces of the flange until the edges intersect.

Circular Cutout creates a found cutout. If you select this option, you must specify a diameter for the circle.

You can also modify the default bend parameters.

NX5 Sheet Metal

Page 42 of 161

Lofted Flange


Lofted Flange is an extruded flange that uses start and end profiles to create the basic shape. The profiles must be open and must be on parallel reference planes. Lofted Flange is particularly useful for HVAC work, as it allows for round to square transitions. You can also create conical bend regions with Lofted Flange.

A Lofted Flange can be either a base or a secondary feature. The command automatically adds bends using the bend radius property. You do not have to draw an arc at each bend location.

NX5 Sheet Metal

Page 43 of 161

Create a lofted flange


To create a lofted flange as a base feature:

1. Create parallel datum planes offset from each other. The offset distance should correspond to the length of the lofted flange you intend to create.

2. Click Lofted Flange . Base Lofted Flange is selected by default if there are no other bodies in the part file.

3. Choose a method for creating the first cross section: sketch a section on a profile

plane or select a section you've already created . Note that both cross sections must be open profiles. When prompted, select the section you sketched, then press Enter.

4. Select the start point for the first section or construct one , then press Enter.

5. Repeat steps 3 and 4 for the second cross section on the second offset plane. The start points for the cross sections (the green cubes in the following illustration) should be in line with each other so as to avoid twisting the shape. (If it is twisted, it cannot be flattened).

6. Select a material side and a thickness value (or accept the defaults).

7. Click OK or Apply to complete the feature.

NX5 Sheet Metal

Page 44 of 161

NX5 Sheet Metal

Page 45 of 161

Lofted Flange options


Curve and Sketch Section let you specify whether to construct the feature from an existing sketch or to create a new sketch from within the feature. For more information on these sketch options, see Using Sketches in NX Sheet Metal.

Point Constructor and point selector let you specify whether to create a new point or select an existing one.

Lofted Flange has the standard bend and corner options. For more details, see Bend parameters for sheet metal features.

NX5 Sheet Metal

Page 46 of 161

Hem Flange


Use Hem Flange to create a feature where the material folds back on itself. Hem Flange is always a secondary feature built on a base part, such as a tab. This command gives you a variety of pre-set shapes. Along with simple open and closed hems, you can create more specialized types, such as curls and loops. The following figure shows some standard hem shapes: closed, curled, s-type, and centered loop.

The Hem Flange dialog box illustrates each type and shows the key dimensions. For example, this is the picture of the Closed type hem, and shows how the key dimension, which in this case is flange length, is measured.

You can make fairly complex shapes quite simply, and you can create hem flanges that chain around part edges.

You can also create hem flanges on curved edges.

NX5 Sheet Metal

Page 47 of 161

Create a hem flange


To create a hem flange:

1. On the NX Sheet Metal toolbar, click Hem Flange .

2. In the Hem Flange dialog box, select a hem shape from the Type list.

3. Select Edge is active. Select a part edge on which to place the hem. If you want the hem to span several edges, select one edge after another. If the hem can be built, you see a preview like this one:

4. Select inset, bend parameter, and relief options. You can change hem types and other

options while still in the command and preview the result.

5. Click OK or Apply to complete the feature.

NX5 Sheet Metal

Page 48 of 161

Hem Flange options


Inset Options specify how far the flange is inset into the base part.

Material

Inside

Insets the hem flange into the base material such that the outside face of the web area is flush with the selected edge.

Material

Outside

Insets the hem flange into the base material such that the inside face of the web area is flush with the selected edge.

Bend

Outside Adds material to the selected edge to form the flange.

Bend Parameters vary depending on the type of hem you select.

Flange Length Measures the length of the flange as shown in the bitmap for that type of hem. For closed types, you only specify one length. For loop, curl, and S-type flanges, you specify two lengths.

Equal Radii Available for hems with two bends. Specifies that the radii for both bends are equal.

Bend Radius Sets the radius of the bend for a given hem. For loop, curl, and S-type hems, specify two radii.

Sweep Angle

Available for open and centered curl-type hems. Specifies the extent of the curl. The maximum value is less than 360. The figures below show two open loop hem flanges with sweep angles of 145 and 350 degrees, respectively.

NX5 Sheet Metal

Page 49 of 161

Closed Corner


Closed Corner modifies two flanges in one operation to close a corner where two flanges meet.

Note the following:

The angles of the adjacent flanges must be less than or equal to 90 degrees. It's best to apply bend and corner relief before using Closed Corner, so that there's a

clean corner to close. The corner should be symmetric, with equal bend radii and bend angles on the adjacent flanges. If there's more than one way to close the corner, edit the flanges themselves to close the corner the way you want it.

NX5 Sheet Metal

Page 50 of 161

Create a Closed Corner


1. Click Closed Corner .

2. Select the bends adjacent to the corner you want to close .

3. Use the feature dialog box to specify corner options.

4. Click OK to finish the corner.

NX5 Sheet Metal

Page 51 of 161

Closed Corner options


Corner Properties

Treatment

Specifies the way the corner is treated:

Open:

Closed:

Circular Cutout:

Diameter (For Circular Cutout treatment only): Specifies the diameter of the circular cutout.

Overlap

Closed brings the inside edges of the corner together.

Overlapping extends one edge. You use Overlap Ratio to specify the amount of overlap.

Gap specifies the amount of gap between the edges. 0.0 is the default. The following figure shows a gap of 1 mm. (The gap cannot be negative or greater than the material thickness.)

NX5 Sheet Metal

Page 52 of 161

NX5 Sheet Metal

Page 53 of 161

3-Bend Corner


3-Bend Corner lets you close corners where three bends meet. The sweep angles of the bends must be less than or equal to 90 degrees, and must all be the same. Similarly, the radii of all three bends must be the same.

NX5 Sheet Metal

Page 54 of 161

Create a 3-Bend Corner


To close a 3-bend corner:

1. Click 3-Bend Corner .

2. Choose the type of corner you want: Open , Closed , or Circular Cutout .

3. Select the first outer bend.

4. Select the second bend.

5. Click OK or Apply to close the corner.

NX5 Sheet Metal

Page 55 of 161

3-Bend Corner options


Corner Properties

Treatment

Specifies the way the corner is treated:

Open:

Closed:

Circular Cutout:

Diameter (For Circular Cutout treatment only): Specifies the diameter of the circular cutout.

NX5 Sheet Metal

Page 56 of 161

Normal Cutout


Normal Cutout has edges that remain perpendicular to the planar face of the part. Normal cutouts are particularly useful when you want to make cuts across bend regions and still maintain a constant material thickness. The feature is useful when you need to Unbend and Rebend sheet metal parts, because non-perpendicular thickness faces created with Extrude-Subtract may be deformed during Unbend/Rebend operations. Normal Cutout maintains sheet metal part properties by always cutting normal to the top and bottom faces of the model. It also conforms to all other global sheet metal part properties.

In many cases, Normal Cutout lets you avoid unbending the part to model a cutout.

NX5 Sheet Metal

Page 57 of 161

Create a Normal Cutout


1. Click Normal Cutout .


3. Draw a profile, or select a section from an existing sketch.

o A closed profile defines the cutout. o An open profile displays a direction handle that is perpendicular to the open

profile and co-planar with the sketch. Use this handle to specify which side of the profile to cut. The following figure shows the effects of reversing the direction handle.

The curves of the open profile are extended tangentially until they intersect themselves to create a closed profile, or until they intersect the edge of the part.

NX5 Sheet Metal

Page 58 of 161

4. Click the type of cut you want to make: Thickness Cut or Mid-Plane Cut.

5. Define the extent of the material you want to remove. If you click Value, you can click Symmetric to specify that you want to create a cut area symmetric in both directions from the sketch plane.

6. Click OK to create the Normal Cutout.

NX5 Sheet Metal

Page 59 of 161

Normal Cutout options


Cutout Properties

Cut Method

Thickness Cut compensates for the material thickness of the part by projecting the profile onto both layer faces, inner and outer (top/bottom), then thickening the resulting surface into a solid tool, and removing the tool from the base part

Mid-Plane Cut projects the profile onto the mid-plane of the sheet metal part, then thickens the resulting surface into a tool body. Usually Thickness Cut consumes more material than Mid-Plane.

Limits

Value lets you define the extent of the cutout manually, either by dragging the depth handle or by entering the distance in the Depth input field.

Between lets you define the extent of the cutout by selecting two parallel planes or faces.

Through Next extends the cutout to the first edge encountered.

Through All extends the cutout through the whole part.

Symmetric Depth is only available if you select Value. This option creates a cut area symmetric in both directions from the sketch plane.

NX5 Sheet Metal

Page 60 of 161

Jog


Jog constructs two 90-degree bends and adds material to them to jog to a planar face of a sheet metal part.

The profile for a Jog feature must be a single linear element and can only be constructed across a planar face. The jog can be minimal: for example, a slight offset or step to provide clearance or rigidity to a part.

NX5 Sheet Metal

Page 61 of 161

Create a Jog


To create a Jog on a tab, or a planar region of a contour flange or lofted flange:

1. Click Jog .

2. Define the profile planeselect the face you want to jog on.

3. Draw a profile or pick one to serve as the Jog Line. The profile must be a single linear element.

4. If necessary, click on the drag handle to define the direction you want to jog. The drag

handle should point toward the portion of the part you want to move. (The following figures illustrate the results produced by selecting different jog directions.)

NX5 Sheet Metal

Page 62 of 161

NX5 Sheet Metal

Page 63 of 161

5. Specify the height of the jog.


NX5 Sheet Metal

Page 64 of 161

Jog options


Jog Properties

Height Specifies the extent of the jog.

Reverse

Direction Changes the direction of the jog from up to down and vice versa.

Reverse

Side Changes the side of the part that moves to create the jog.

Height Reference

Inside applies the dimension from the selected face to the near side of the feature.

Outside applies the dimension from the selected face to the far side of the feature.

Inset

Material Inside positions the portion of the feature that is perpendicular to the profile plane inside of the profile plane.

Material Outside positions the portion of the feature that's perpendicular to the profile plane outside of the profile plane.

Bend Outside positions both the portion of the feature that's perpendicular to the profile plane and the bend outside of the profile plane.

Extend Section Extends the linear profile you draw to the edges of the part.


NX5 Sheet Metal

Page 65 of 161

Bend


Use this command to create a bend in a planar area on a sheet metal part.

NX5 Sheet Metal

Page 66 of 161

Create a Bend


1. Click Bend .


3. Draw a profile. The profile, which must be a single linear element, represents the approximate location of the bend.

4. Define the bend location with respect to the profile.

5. To change the default bend angle (90 degrees), drag the angle handle or enter a value in the input field.

6. Specify the side of the part to move. The direction arrow points towards the portion that

will move.

To change the direction, double-click the direction arrow.

NX5 Sheet Metal

Page 67 of 161

7. Define the bend direction. To change the bend direction, double-click the direction arrow.


NX5 Sheet Metal

Page 68 of 161

Bend options


Bend Properties

Angle Specifies the angle of the bend.

Reverse

Direction Changes the direction of the bend from up to down and vice versa.

Reverse

Side Changes the side of the part that moves to create the bend.

Inset

Outer Mold Line Profile specifies that the profile represents the line created by the junction between the planar stationary region and the cylindrical bend region in the flattened state.

Bend Center Line Profile specifies that the profile line represents the center line of the bend, and that the bend region will be distributed evenly on either side of the profile in the flattened state.

Inner Mold Line Profile specifies that the profile represents the line created by the junction of the planar web region and the cylindrical bend region in the flattened state.

Material Inside positions the portion of the feature that is perpendicular to the profile plane inside of the profile plane.

Material Outside positions the portion of the feature that's perpendicular to the profile plane outside of the profile plane.

Extend Section Extends the linear profile you draw to the edges of the part.


The following figures show how the bend is positioned differently, depending on which bend location option you choose. The extended plane going through the part is a visual aid to highlight the bend location. Note: The Bend Center Line, Inner Mold Line, and Outer Mold Line profiles need to be shown in the flattened state because this is the state in which these measurements make sense.

Bend Location Graphic

NX5 Sheet Metal

Page 69 of 161


Outer Mold Line Profile

Bend Center Line Profile

Inner Mold Line Profile

NX5 Sheet Metal

Page 70 of 161


Material Inside

Material Outside


NX5 Sheet Metal

Page 71 of 161

Unbend

Overview How To

Use this command to unbend a portion of the part so you can construct a cutout or a hole across the bend. Don't use Unbend to create the flat patternuse Flat Solid and Flat Pattern instead. You can apply a rebend on top of the unbend feature to represent the true formed state of the model.

NX5 Sheet Metal

Page 72 of 161

Unbend a part

Overview How To

1. Click Unbend .

2. Select a planar face or planar edge that you want to remain in a fixed position.

3. Select the bend(s) you want to unbend.

Note: You can toggle (Preview) to see the unbent and rebent part.


If you create a part that intersects itself at any point during its development, either when creating it or when unbending or rebending, any further unbend or rebend operations may result in an error. If this happens, roll the part back to the step before the self-intersection and try to correct the self-intersecting condition.

NX5 Sheet Metal

Page 73 of 161

Rebend

Overview How To

Use this command to rebend a part after you've unbent it to add a feature, such as a cutout, across a bend.

NX5 Sheet Metal

Page 74 of 161

Rebend a part

Overview How To

1. Click Rebend .

2. Select a face that was unbent with the Unbend command. (You can rebend more than one unbent feature in one operation.)

You can also click (Preview) to see the rebent and unbent part.


If you create a part that intersects itself at any point during its development, either when creating it or when unbending or rebending, any further unbend or rebend operations may result in an error. If this happens, roll the part back to the step before the self-intersection and try to correct the self-intersecting condition.

NX5 Sheet Metal

Page 75 of 161

Dimple


Use this command to construct an indentation in a sheet metal part. You use a sketched profile as the dimple outline. Like Drawn Cutout, Dimple makes an indentation in the sheet metal part, using a sketched profile as its outline. The principal difference between the two is that a dimple has a bottom and a drawn cutout doesn't. Dimples can't be flattened.

NX5 Sheet Metal

Page 76 of 161

Create a dimple


1. Click Dimple .

2. Pick the profile plane.

3. To create the dimple profile, select an existing sketch, or define a new one using the options from the dialog. If you use an open profile, its open ends must intersect part edges. If you create an open profile where the curves don't intersect the outer edges of the part, the software extends the ends of the profile curves tangentially until they either intersect one another or intersect the edges of the part. A closed profile can't touch any part edges.

4. (For open profiles only) Double-click the side handle to specify the side of the profile to move during the Dimple operation.

5. Set the dimple depth.

6. Set wall, dimension, and rounding options, if any.


NX5 Sheet Metal

Page 77 of 161

Dimple options


The following options are available for Dimple: Dimple Properties

Depth Specifies the extent of the dimple.

Reverse

Direction Changes the direction of the dimple from up to down and vice versa.

Side Angle

Specifies the taper angle for the dimple. (The angle is measured relative to the default sidewall angle of 90 degrees.) The dimple in the following figure has a side angle of 20 degrees. The section corners have been rounded (the original profile sketch was rectangular), but there's no rounding for die or punch.

Depth Reference

Inside measures the dimension from the selected face to the near side of the feature.

Outside measures the dimension from the selected face to the far side of the feature.

Sidewalls

Material Outside specifies that the sidewalls for the dimple are constructed so that they lie outside the profile.

Material Inside specifies that the sidewalls for the dimple are constructed so that they lie inside the profile.

Rounding

Round Dimple Edges Lets you supply values for the dimple's punch and die radii.

Punch Radius Specifies the radius value at the bottom of the dimple (P below).

NX5 Sheet Metal

Page 78 of 161

Die Radius Specifies the radius value at the base of the dimple (D above).

Round Section Corners

Specifies that you want to round any sharp corners in the profile. This option allows you to draw the profile without arcs. If you choose this option, you must supply a Corner Radius. You can't select this option If you use a circular profile.

NX5 Sheet Metal

Page 79 of 161

Louver


Louver lets you create and customize a sheetmetal venting feature.

A louver is constructed using a single, linear element. The louver depth (D) must be equal to or less than the louver width (W) minus the material thickness (T).

NX5 Sheet Metal

Page 80 of 161

You can also specify whether you want the louver ends formed (A) or lanced (B).

Louver features can't be flattened.

NX5 Sheet Metal

Page 81 of 161

Create a louver


1. Click Louver .


3. Draw a profile. The profile must be a single linear element.

4. Define the louver depth and height.

5. Specify whether you want the louver ends lanced or formed.

6. Specify whether you want rounding, and if so, supply a radius value. (In the following figure, the louver on the left has a die radius of 2 mm.)


NX5 Sheet Metal

Page 82 of 161

Louver options


The following options are available for Louver: Louver Properties

Depth

Specifies the extent of the louver, measured from the base surface to the top of the louver. The louver depth (D) must be equal to or less than the louver width minus the material thickness.

Reverse

Direction Changes the direction of the louver to the opposite side of the base part.

Width

Specifies the width of the louver, measured from the Cut Line to the front edge.

Reverse

Direction Moves the louver to the other side of the Cut Line (profile).

NX5 Sheet Metal

Page 83 of 161

Louver Shape Formed gives you a rounded shape with closed ends.

Lanced gives you squared-off open ends.

Rounding

Round Louver Edges

Gives you a fillet at the edge where the louver meets the flat surface. If you select this option, must supply a value for Die Radius.

NX5 Sheet Metal

Page 84 of 161

Drawn Cutout


Use this command to construct a sheet metal drawn cutout.

Like Dimple, Drawn Cutout makes an indentation in the sheet metal part, using a sketched profile as its outline. The principal difference between the two is that a dimple has a bottom and a drawn cutout doesn't. Drawn cutouts can't be flattened.

NX5 Sheet Metal

Page 85 of 161

Create a drawn cutout


1. Click Drawn Cutout .

2. Select the profile plane.

3. To create the drawn cutout profile, select an existing sketch, or create a new one. If you use an open profile, the open ends of the profile must intersect part edges. A closed profile can't touch any part edges.

4. (For open profiles only) Double-click the side handle to select the side of the profile to move during the Drawn Cutout operation. The following graphics show how the side handle direction affects the way the feature is created.

5. Set the depth of the drawn cutout.

6. Set wall, dimension, and rounding options, if any.

NX5 Sheet Metal

Page 86 of 161


NX5 Sheet Metal

Page 87 of 161

Drawn Cutout options


The following options are available for Drawn Cutout: Cutout Properties

Depth Specifies the extent of the cutout.

Reverse

Direction Changes the direction of the cutout to the opposite side of the base part.

Side Angle

Specifies the taper angle for the cutout. (The angle is measured relative to the default sidewall angle of 90 degrees.) The drawn cutout in the following figure has a taper angle of 10 degrees. It displays rounding of cutout edges (die radius with a fillet of 2 degrees). Section corners haven't been rounded.

Sidewalls

Material Outside specifies that the sidewalls for the dutout are constructed so that they lie outside the profile.

Material Inside specifies that the sidewalls for the cutout are constructed so that they lie inside the profile.

Rounding

Round Cutout Edges Lets you supply values for the cutout's die radius.

Die Radius Specifies the radius value at the base of the cutout. The figure on the left shows no rounding.; the figure on the right has rounded cutout edges (radius 2 mm) and rounded section corners (also 2 mm radius).

NX5 Sheet Metal

Page 88 of 161

Round Section Corners

Specifies that you want to round any sharp corners in the profile. This option allows you to draw the profile without arcs. If you choose this option, you must supply a Corner Radius.(See the graphic on the right, above.) You can't select this option If you use a circular profile.

NX5 Sheet Metal

Page 89 of 161

Bead


Bead constructs a bead feature on a sheet metal part. Beads are often used to stiffen sheet metal parts. You can specify the shape of the bead cross section and the type of end condition treatment you want. For example, you can specify whether the bead shape is circular, U-shaped, or V-shaped. You can also specify whether the ends of the bead are formed, lanced, or punched. Beads can't be flattened.

NX5 Sheet Metal

Page 90 of 161

Create a bead


1. Click Bead .

2. Select the profile plane.

3. Create a profile for the Bead. The profile can be open or closed.

Multiple elements in the profile must be tangent continuous. You can also construct a single Bead feature using multiple, separate profiles. Each profile must be a continuous set of tangent elements, but the profiles can cross each other. The radius of any arcs in the profile must be more than half the width of the bead itself.

4. Choose a bead cross-section type and specify dimensions for it. The icons in the dialog indicate how the dimensions are measured:

o For Circular: Depth and Radius. (Depth must be less than Radius.)

o For U-Shaped: Depth, Width, and Angle.

o For V-Shaped: Depth, Radius, and Angle.

5. Choose a treatment option for the ends of the bead:

o Formed (the default)

NX5 Sheet Metal

Page 91 of 161

o Lanced

o Punched

6. Specify rounding options.

7. Click OK to complete the Bead feature.

NX5 Sheet Metal

Page 92 of 161

Bead options


Bead Properties

Cross Section

Specifies the type of bead:

Circular creates a bead in a half-circle

shape.

U-Shaped creates a bead with a flat bottom and angled

sides.

V-Shaped creates an arc-shaped bead with an inside radius that

you can modify.

Depth

Specifies the extent of the bead. The bitmap image for each type shows how the depth is measured. In this figure, D indicates the

depth.

Reverse

Direction Changes the direction of the bead in relation to the base part.

Radius (Circular and U-Shaped only)

The radius of the curve on the inside of the bead. R = radius (Circular

bead in this case) .

Width The width at the bottom inside of the U-Shaped bead as shown here. W =

NX5 Sheet Metal

Page 93 of 161

width

Angle (U-Shaped only)

Specifies the taper angle for the bead. (The angle is measured relative to the default sidewall angle of 90 degrees.) In this figure, A =

angle

End Condition

Controls the shape of the ends of the bead.

Formed creates ends that are rounded.

Lanced creates ends that are cut.

Punched creates ends that are cut with a relief. If you select this options, you must specify the extent of the relief by supplying a value for Punched Width.

Rounding

Round Bead Edges Lets you supply values for the bead's die and punch radii. Not recommended when using the bead to construct a pattern feature that contains a large number of beads.

Die Radius Specifies the radius value at the top of the bead.

Punch Radius Punch Radius specifies the radius value at the bottom of the bead. Only available for U-Shaped.

NX5 Sheet Metal

Page 94 of 161

Solid Punch


Use Solid Punch when you want to create a sheet metal feature that inherits the shape from the punch type tool body.

The Solid Punch is created with a die-type or punch-type tool body. A die-type tool body models the negative (void) shape, and a punch-type models the positive shape. The following figures show the tool body and the target (the green sheet), the tool body used as a die, and finally the tool body used as a punch.

NX5 Sheet Metal

Page 95 of 161

NX5 Sheet Metal

Page 96 of 161

Create a solid punch


Both Solid Punch types follow the same basic procedure.

1. Click Solid Punch .

2. Select a Type: Punch to model a positive shape or Die to model a void.

3. Select a target face (the face first touched by the tool body).

4. Select a tool body.

5. If the tool does not intersect the tool body, select a Csys or point to define the from location on the tool and a Csys or point to define a to location on the target. The following figures show the locations of the From Csys on the tool body and the To Csys on the target, then the result (in this case, a Die type punch).

NX5 Sheet Metal

Page 97 of 161

6. (Optional) Select Pierce Faces from the tool body. These faces will be removed from the target.

7. Enter a thickness value if the Infer Thickness option is not selected.

8. (Optional) If you do not want the tool to be visible once you create the punch feature, select Hide the tool body.

9. Select other options.


NX5 Sheet Metal

Page 98 of 161

Solid Punch options


Solid Punch Properties

Thickness Specifies the thickness of the solid punch.

Infer Thickness Specifies that the solid punch thickness should be inferred from the target solid.

Auto Centroid Creates a point at the centroid of the solid punch intersection curves. You can use this point for manufacturing purposes.

Hide the tool body Hides the tool body once the punch has been created.

Rounding

Round Solid Punch Edges

Applies die blends to the non-g1 edges between the solid punch and the target body. If this option is on, you must supply radius values.

Die Radius The radius of the inside rounded edge where the punch meets the target (D in the figure below).

Punch Radius

The radius of the outside rounded edge where the punch meets the target (P in the figure below.). In general, Punch Radius is the Die Radius plus the thickness.

Constant Thickness

Blends sharp edges with constant thickness on the tool body.

The following figures illustrate the difference.

NX5 Sheet Metal

Page 99 of 161

Constant Thickness off

Constant Thickness on

NX5 Sheet Metal

Page 100 of 161

Edge Rip

Overview How To

Use Edge Rip when you want to rip along corner edges, for example when converting a solid model to a sheet metal part. Edge Rip can also be used any time you need to separate two parts of a model so that they can act independently. Use this command if you want your edges ripped as a separate activity, rather than as part of the Convert to Sheetmetal process.

An additional feature of Edge Rip lets you rip along a linear sketch. You could use this capability, for example, to separate two parts of a flange and bend one of them.

NX5 Sheet Metal

Page 101 of 161

Rip an edge

Overview How To

To rip the edges on a part:

1. Click Edge Rip

2. Select the edges you want to rip.

3. Click OK to complete the operation.

To rip along a linear sketch:

1. Click Edge Rip .

2. Select an existing section or sketch one on the face of a part.

3. When prompted for the Section, select the line you sketched, as shown.

4. Click OK to rip along the line.

NX5 Sheet Metal

Page 102 of 161

You can now treat the two parts of the flange as separate surfaces, for example by creating a bend along one section of the original flange.

NX5 Sheet Metal

Page 103 of 161

Convert to Sheetmetal


Use Convert to Sheetmetal to convert plain solid models created in the Modeling application to NX Sheet Metal models.

NX5 Sheet Metal

Page 104 of 161

Convert a solid model to a sheet metal part


1. Click Convert to Sheetmetal .

2. Select the part you want to convert.

3. Select a planar base face (preferably one that has tangent continuity with the other faces in the model, or that will have after you rip edges).

4. Select the edges that you want to rip .

5. Click OK to complete the conversion.

If you unbend or flatten a part and then use Convert to Sheetmetal, you cannot rebend the areas that were previously unbent.

Tips and techniques for using Convert to Sheetmetal Successful conversion of a model into sheet metal largely depends on the topology of the part and the base (seed) face you select. A face that has tangent continuity with other faces in the model gives better results after conversion. You can use the edge-rip option to achieve tangent continuous faces.

For example, in the part shown below, the red faces can never be tangent continuous to each other. The green faces are tangent continuous to rest of the body, but not to the corners of the

NX5 Sheet Metal

Page 105 of 161

box. So, after selecting a green face as the base, you would select edges to rip that make the remaining body also tangent continuous (in this case, the back corner edges).

The following graphic shows the part after conversion. Note that picking a red face as the base face wouldn't have produced as good a conversion.

Here's another example of a part where the selecting a red face as the base face wouldn't produce a good conversion.

NX5 Sheet Metal

Page 106 of 161

Convert to Sheetmetal options


You can specify whether you want bend relief applied to the bends in the part, and if so, what type and dimensions. For more information on this topic, see Bend parameters for sheet metal features.

NX5 Sheet Metal

Page 107 of 161

Control individual bend regions

Overview How To

You can control the geometry of individual bend regions. You can change bend angle, bend radius, and the neutral factor of a given bend. There is a separate command for each type of change, and the modifications appear as separate entities in the Part Navigator, as shown below:

Model History Datum Coordinate System (0) SB Tab (1) SB Secondary Contour Flange (2) SB ResizeBendAngle (3) SB ResizeBendRadius (4)

There is a separate command for each type of change. These capabilities let you change individual bends in features such as contour flanges and jogs that create multiple bend regions. Also, when you bring in parts with the Convert to Sheet Metal command, you can modify individual bend regions to suit the demands of the part. You no longer need to go back to Modeling, revise the part, and reconvert it.

For manufacturing, you can visualize parts with bends in interim states, showing, for example, a 90-degree flange first at 45 degrees and then rebent to the full 90 degrees. Since these features are in timestamp order, you can hide and show the direct edit features to display the model in various states of forming.

NX5 Sheet Metal

Page 108 of 161

Resize bend radius, bend angle, and neutral factor

Overview How To

To change bend angle, bend radius, or the neutral factor of a bend, you follow the same general procedure.

1. On the NX Sheet Metal toolbar, click one of the following buttons:

o Resize Bend Radius .

o Resize Bend Angle

o Resize Neutral Factor

2. (For Resize Bend Angle only). Select Face is active. Select a non-thickness face to remain stationary when you change the bend angle .

3. Select Bend is active. Select the bend(s) you want to modify.

4. Supply a new parameter value for angle, radius, or neutral factor.

5. (For Resize Bend Angle only). Select the Keep Radius Fixed check box if you do not want the radius to change with the change in angle. If the radius stays fixed, the web length must change.

6. Click OK or Apply to make the change.

NX5 Sheet Metal

Page 109 of 161

Flat Solid

Overview How To Related Topics

Flat Solid allows you to create a flat representation of the part in the same file as the formed sheet metal part. The flattened version of the part is associative to the formed version. When you flatten a sheet metal part this way, a Flat Solid feature is added to the end of the Model History in the Part Navigator. If the part contains deformation features, they are retained in their formed condition. If the sheet metal model changes, the flat pattern automatically updates to include the new feature.

Model History

Fixed Datum Plane (0) Fixed Datum Axis (1) Fixed Datum Axis (2) SB Tab (3) SB Flange (5) SB Flange (7) SB Closed Corner (9) SB Edge Rip (13) Sketch (17) SKETCH_... SB Flat Solid (18)

NX5 Sheet Metal

Page 110 of 161

Create a flat solid

Overview How To Related Topics

1. Click Flat Solid .

2. Select a face that you want to orient upward.

3. Select an edge to define the X axis and origin.

4. (Optional): Select Move to Absolute CSYS to move the flattened representation of the part to the model space coordinate system.

5. Click OK to finish the flat representation of your part.

NX5 Sheet Metal

Page 111 of 161

Flat Pattern


Flat Pattern lets you create a solid or wireframe flat representation of a 3D sheet metal part. You can include annotations for bending, punching, or cutting manufacturing instructions. Included are facilities for automatic bend region annotations, and options for the line color, layer, and font used for the various line types (outline, bend centerline, bend tangents, and so on). You can then export the flat pattern through a translator to a cutting tool for the manufacture of the part.

Note: The recommended translator for exporting flat patterns to tools is 2D Exchange. Choose FileExport2D Exchange.

NX5 Sheet Metal

Page 112 of 161

Create a flat pattern


1. With your part displayed, click Flat Pattern .

2. Pick an upward face to orient the flat pattern . This face can either be on a formed sheet metal body, or on a Flat Solid body. The normal direction associated with this face is used to specify the UP direction for bend regions.

Note: Flat Pattern needs a Flat Solid body as the basis for the flat pattern curves. So if you select a face on a formed sheet metal body as the base face for the Flat Pattern, a Flat Solid feature will be automatically created as the basis for the Flat Pattern curves. When you create a Flat Solid, the face you select on the formed sheet metal body will be used as the placement face for the Flat Solid and the base face for the Flat Pattern. As a result, this placement face eventually defines the UP direction for the bend region annotations on the flat pattern.

3. Click OK to create the feature.

4. To see the FLAT-PATTERN, in the Part Navigator, click to expand Model Views, then double-click the FLAT-PATTERN view.

Edit a flat pattern To edit the orientation or placement of the flat pattern, you must edit the orientation of the flat solid feature that it references. This is true both for flat patterns created from flat solids and those created from a formed sheet metal body. The flat pattern is simply a grouped set of curves and associated annotations. You can add, remove, or edit curves in this group. However, any time you update the model, the curves associated with the flat pattern will be regenerated and will overwrite any changes. To make permanent changes to a flat pattern, you must first make a non-associative copy of the flat pattern curves and then edit that set of curves.

Export a flat pattern Exporting a Flat Pattern through a translator requires a proper translator license. This license is not included as part of NX Sheet Metal.

You can export a flat pattern as follows. With the part file that contains the flat pattern open:

1. Choose FileExport2D Exchange. Select the Files tab. 2. Under Export to, for Output As, select DXF or DWG, and specify where you want to

save the new file.

3. Select the Data to Export tab. For Export, choose Selected Objects. Then in the graphics window, click on the Flat Pattern group. (It should all highlight at once.)

4. For (the second) Export, choose Selected View, select FLAT-PATTERN from the View List, then click OK to export.

You can also use Save As to save your flat pattern:

Choose FileSave As, specify a name and a folder location for the file, and for Save as type, select DXF or DWG.

NX5 Sheet Metal

Page 113 of 161

Flat Pattern options


Because most companies have standards for their flat patterns, you may want to establish default settings for flat pattern curve display and annotation. See the following topics for instructions:

Set Flat Pattern Display options Use Flat Pattern Custom Callouts

NX5 Sheet Metal

Page 114 of 161

Set Flat Pattern Display options


NX Sheet Metal provides display options for a wide range of curve types, including bend lines, bend tangent lines, inner and outer mold lines, and so on. You can establish defaults in Customer Defaults, and you can change settings for each part individually in sheet metal Preferences.

To change the Customer Defaults for Flat Pattern:

1. Choose FileUtilitiesCustomer DefaultsSheet MetalFlat Pattern. 2. Select the Curves tab to manage which curves will be displayed and how. Each curve

type has a box with an Enabled check box, the feature name, a color box to choose the color, and menus for line font style and width. There is also a box to specify the layer.

o To change the color, click in the color box. The color palette displays. Click a color, then click OK.

o Set line type and line width for the curve you want to display by choosing from the Font and Width lists.

o Set the layer by typing in a new value, or accept the default (1). o Repeat these steps for each type you want to display on your Flat Pattern.

3. Select Enabled for each type you want displayed. Then click OK

To set non-default display options for Flat Pattern in a part file:

1. Choose PreferencesNX Sheet Metal. 2. Choose Flat Pattern Display.

3. Under Curves, change color, font, and width in the same way you did it in Customer Defaults.

4. Select the line types you want displayed and clear the check boxes for the ones you don't want visible.

5. Click OK to set the options.

NX5 Sheet Metal

Page 115 of 161

Use Flat Pattern Custom Callouts


NX Sheet Metal has six templates that you can use to create callouts for display on your flat pattern. You can customize them and control their availability in the Customer Defaults file. Each callout has the following:

Name: specifies the name of the callout as it appears in the NX Sheet Metal Preferences dialog. You can change this name.

Object Types: indicates the types of objects to which particular callouts can be associated, in order of preference. For example, Bend Radius would be associated with Bend Center Line first. If bend center lines are not shown on the flat pattern, it would be associated with the second item in the list, Outer Mold Line, and so on. You cannot change the object types, but you can control their display on the flat pattern by:

o Making them unavailable in Customer Defaults. o Turning them off in NX Sheet Metal Preferences. o In the Object Types field, changing the order of the types or deleting ones that

you don't want to display.

Content: specifies the text that appears in the callout in your flat pattern. You can change portions of this, for example, displayed name, and number of decimal places. In the following flat pattern, we changed Bend Radius to R and Bend Angle to A.

Available: controls whether the callout is visible on the NX Sheet Metal Preferences

dialog.

Enabled: controls whether the callout is created by default on your flat pattern.

NX5 Sheet Metal

Page 116 of 161

NX Sheet Metal Template Defaults for Custom Callouts

Name Object Types Content

Bend Radius Bend Center Line, Outer Mold Line, Inner Mold Line Bend Radius =

Bend Angle Bend Center Line, Outer Mold Line, Inner Mold Line Bend Angle=

Bend Direction Bend Center Line, Outer Mold Line, Inner Mold Line Bend Direction=

Aerospace Sheet Metal only

Hole Diameter Hole Diameter Hole Diameter =

Joggle Runout Joggle Line Joggle Runout =

Joggle Depth Joggle Line Joggle Depth =

For each part file, you can create six new callouts in Customer Defaults. NX Sheet Metal remembers up to five sets of six new custom callouts. After that, it won't accept any new ones.

To customize the default callouts, choose FileUtilitiesCustomer DefaultsSheet MetalFlat PatternAnnotations. You see six Custom Callout templates. For each callout template:

1. (Optional) Change the name that is displayed on the NX Sheet Metal Preferences by typing a new one in the Name box.

2. Customize the callout that is displayed on the flat pattern by changing the text string in the Content box. For example, to change Bend Angle to BA, you would type the following: BA = .

3. Repeat steps 23 for as many of the Custom Callout templates as you want to have the option to display.

4. Select Available for each callout that you want to have show up in Preferences. Select Enabled for all the callouts that you want to have appear by default on your flat pattern. (You can disable their display in Preferences on a per file basis.)

5. Click OK to save your changes. You have to start a new NX session for these defaults to take affect.

Customizing callout display in a sheet metal part file Once you create custom callouts, they are listed in Current callouts in part on the Flat Pattern Display tab in NX Sheet Metal Preferences. Enable the ones you want to see and disable the ones that you want to hide. If you don't, you may have two sets of callouts for each feature, your customized label and the default.

Formatting custom callout text To create your own custom callouts in NX Sheet Metal, you can use the special keyword language shown in the default callouts. A key looks like this:

These keys g

Documents

UG_BKM