U10DESCRIPTION
1 000-6207 2 END CAP 2 000-6244 1 ISIS TRUVATIV 118MM X 160MM BB 3
000-6264 1 SEAT, MED WIDTH 4 000-6324 1 CRANK ARM LEFT HAND 5
001-0391 1 CRANK ARM RIGHT HAND 6 001-0424 1 WATER BOTTLE HOLDER 7
001-0458 1 DECAL, WARNING, U/R916 8 001-6347 1 KEYPANEL, OVERLAY,
RIGHT 9 001-6365 2 DISC, CRANK 10 01-4034 2 BOLT BH , 8-32 x 1¾''
ZINC 11 01-4036 2 BOLT BH , 3/8 -16 x ¾'' ZINC 12 01-4048 1 BOLT BH
, 3/8 -16 x ½'' 13 01-4064 2 BOLT BH 3/8-16 X 2" ZINC 14 01-4094 1
BOLT BH, 5/16 -18 UNC x 2¼'' - ZINC 15 01-4113 2 Button HD Joint
Connector, 3/8-16 X 1.06 16 01-4126 2 BOLT BH ,¼ -20 x ½'' SS BLACK
17 02-3021 2 SCREW SHCS , 10-32 UNC x ½ 18 02-3058 4 SCREW #8-32 X
1 PHIL PAN HEAD ZINC 19 02-3062 8 #6 -32 UNC THREAD x 1" OVAL HEAD
PHILLIPS
M/S _SS-BLACK OXIDE 20 02-4130 2 SCREW, SET, ¼ -20 UNC x ½ 21
02-4174 4 SCREW SHCS , ¼ -20 UNC x ½ Zinc 22 02-4177 4 SCREW SHCS ,
3/8 -16 UNC x 1 Zinc 23 02-9305 3 M5 X 0.8 X 16M Philipps Pan Head
Screw 24 02-9306 3 M5 X 0.8 X 80M Philipps Pan Head Screw 25
02-9307 4 SCREW, M6-1.0 X 20mm L, SHCS, STAINLESS 26 03-1035 2 3/8"
Lock Nut 27 03-3043 1 5/16" Lock Nut 28 03-4031 6 8-32 INSERT HEX
29 03-4034 10 10-32 INSERT HEX 30 03-4036 8 RIVNUT 10-32 NF,
.125-.225 31 03-9080 1 M8-1.0 Hex Fin Jam Nut 32 04-2021 1 WASHER,
FLAT, 3/8" USS 33 05-5130 2 IGUS FLANGE .5 ID x .5938 OD x .25L 34
05-5146 3 EB-TENSIONER BRACKET MOUNT BUSHING 35 07-1156 2 6204-2z
Ball Bearing Double Sealed 36 08-5186 1 SPACER NYLON 5/8 DIA X 1/2
L 37 09-8080 1 TYRAP, .14 X 11.0 38 10-4040 1 LeeSpring-LHL750A 07
39 12-1151 2 DECAL SEAT ADJUSTMENT 1-13 R10 40 12-1380 1 Made In
USA 41 12-1822 1 Honix Console Decal 42 12-5621 2 NLS ONE 3” Dome
Decal (000-6491) 43 12-6180 1 Decal, Parts Diagram Schematic U10 44
12-6304 1 DECAL, U10 "E-BRAKE TECHNOLOGY" LEFT 45 12-6305 1 DECAL,
U10 "E-BRAKE TECHNOLOGY" RIGHT 46 12-6308 1 Membrane Switch Overlay
for Honix Display 47 12-7500 1 MPale Antimicrobial Label 48 12-7501
1 Caution 15V and 4A 49 12-8005 1 DECAL SEAT ADJUSTMENT 1-4 U10 50
19-1013 1 TAPE DBL SIDED 2 3/4" WIDE 51 19-1043 1 U10 Quick
Assembly Instructions (Hardcopy
Printed) 52 19-6000 1 DVD Technical Documentation 53 27592 3
WASHER, M8, SPLIT LOCK 54 40654 28 SCREW, #10-32 X .75, PAN HEAD,
W/LOCK
WASHER 55 56-0584 2 Wheel (56-0580 Drilled Out to .641 ID) 56
56-0585 2 Wheel Sleeve (for 56-0584) 57 56-0587 1 SPRING GAS
LOCKING IN COMPRESSION 100N 58 57-0350 1 Power Adaptor, 15VDC, 4A
59 57-0355 1 BATTERY 12V 1.3 Ah 60 57-0373 1 PULLEY 8 GROOVE 11
3/4" DIA 61 57-0376 1 DC BLOWER FAN ASSEMBLY 62 57-0388 1 Seat
Slide Cap 1 ½ x 3 Rect 63 57-0389 1 Seat Slide guide 1 ½ x 3 Rect
64 57-0391 2 BUSHING SEAT SHOCK MOUNT 65 57-0465 1 H10 Console ATSC
DOM TV KIT 10" 66 57-0469 1 CABLE POWER INPUT E10, U10 67 57-0478 1
Assembly Cable Contact Heart Rate 68 57-0479 1 BELT J Groove 8 Rib
63" / Drive belt U10 69 57-0482 1 Eddy Brake/Gen with clutch
(FB62HA21)
ITEM PART NO. Default -
DESCRIPTION
70 57-0485 1 Lower Control Board, BLCB011 71 57-0487 1 BRACKET
POWER INLET 72 57-0497 4 SPACER, #10 SCREW, 5/16" 73 57-0507 1
Board Interface to Lower Control 74 57-0511 1 EB-COMPRESSION SPRING
RETAINING BRACKET 75 57-0536 1 TV Cable Assembly, E/U/R 10 Series
76 57-0537 1 CABLE ASSY, T-BAR GRIP TO CONSOLE, RoHS 77 57-0538 1
ASSEMBLY FAN INPUT POWER CABLE R10, U10 78 57-0541 1 U10 MAIN
SHROUD, LEFT 79 57-0542 1 U10 MAIN SHROUD, RIGHT 80 57-0545 2 GRIP
CHR /ROC TOP ASSEMBLY 81 57-0546 2 GRIP CHR TOP ASSEMBLY 82 57-0547
4 GRIP CHR BOTTOM ASSEMBLY 83 57-0554 1 CABLE, Console to LCB, R10,
U10 84 57-0555 1 INLET COVER U10 BLACK 85 57-0557 1 Mast Shield
Right Side 86 57-0562 1 CABLE, Intermediate Board to BCLB002,
E10,
U10, R10 87 57-0563 1 CABLE, Intermediate Board to BCLB002 88
57-0566 1 SEAT LOCKING HEX NUT 89 57-0567 1 SEAT LOCKING STOP PLATE
90 57-0568 1 NYLON SEAT LOCK 91 57-0574 1 Handle with 3/8"-16
Threaded Stud 92 57-0608 1 I-POD MOUNT 93 57-0611 1 Pocket, Peel
& Stick, Cardio Schematic 94 70-1208 1 ASSEMBLY, FRAME U10 BIKE
95 71-1203 1 Weldment Front Display Mast U10 Bike 96 72-1213 1
Weldment Seat Handle 97 73-1206 1 EB BELT COMPRESSION SPRING
TENSIONER 98 75-1205 1 Weldment Seat Adjustment Vertical 99 75-1207
1 SEAT MOUNT SLIDE ASSEMBLY
100 75-1208 1 Seat Slide Housing Bracket 101 899-0004 1 DECAL
SERIAL/COMPLIANCE U9/U10 102 901-5496 2 SCW-PHP #10-32x1.25 SS 103
902-4707 4 SCREW SHCS, M6-1.0 X 10, SHCS, BLACK,
EPOXY 104 902-5681 7 SCW-SHCS M8-1.25x25 SS 105 91-999 1 Paint (1.5
lbs) 106 95-0614 L 1 PEDAL EXERCISER JD-48-A 9-16 LEFT 107 95-0614
R 1 PEDAL EXERCISER JD48-A 9/16 RIGHT 108 95-9004 1 Packaging Kit
Estimate U10 109 SM000-6218 1 ASSEMBLY, HANDLEBAR 110 SM001-6348 1
KEYPANEL, OVERLAY, LEFT 111 SM002-0540 2 PCB, CHR INTER-CONNECT 112
SM13180 4 CAP, LEVELING SUPPORT 113 SM17686 4 PAD, LEVELING 114
SM17787 2 CONNECTOR, RF, 3MM, F 115 SM21607 2 TAPE, DOUBLE SIDED,
FOAM 116 SM22214 1 WASHER, FLAT, 5/16" SAE ROHS 117 SM27579 4
WASHER, M6, FLAT, ZINC PLATED 118 SM40235 1 FASTENER, HOOK 119
SM40236 1 FASTENER, HOOK 120 SM41269 2 Grommet, 2879, 7/8" ID
U10 U10 Upright Bike
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Customer Service & Parts 800/ 235-2233 General Parts Requests:
[email protected] Field Service Requests:
[email protected] GSA Parts Requests:
[email protected]
Med-Fit Systems, Inc. 800/ 831-7665
www.medfitsystems.com
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS
www.medfitsystems.com REV F
57-0388
12-1151
Note 02-4130: 1. Add(Blue)Loctite 242 to threads. 2. Thread set
screws in place leaving 1/8" threads exposed to stop travel of
seat.
U10 U10 Upright Bike
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS
www.medfitsystems.com REV F
001-0424
57-0465
57-0465
57-0465
57-0465
57-0465
01-4126
01-4126
57-0608
57-0381
12-6308
57-0465 (Shown) H10 Console ATSC DOM TV KIT 10" 57-0470 (Optional)
H10 Console DVB-T TV KIT 10" 57-0393 (Optional) H10 Console Kit
7"
U10 U10 Upright Bike
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS
www.medfitsystems.com
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS Customer Service & Parts 800/ 235-2233 General Parts
Requests:
[email protected] Warranty Field Service Requests:
[email protected] Med-Fit Systems, Inc. 800/
831-7665
www.medfitsystems.com
SM27579 x 4
To Install: 1) Install and Tighten clockwise using "AM BB ISIS
DRIVE Tool" with "LOCTITE 243 BLUE" until bearing cup is secure. 2)
Add outer Jam Nut ring secure with Flat faced screw driver.
To Remove: 1) Loosen jam ring (turning counter clockwise) with
screw driver in one of the slots. 2) Use "AM BB ISIS DRIVE Tool"
and turn counter clockwise to loosen threads. Note: This may take
some pressure to loosen due to working loose the current thread
lock solution.
Use Pedal Wrench such as "Park Tool PW- 3" available at your local
Bike Shop for Loosening Pedals
To Install Bolt: Tighten Bolt securely by applying approximately
40ft/lbs of torque.
To Remove: loosen bolt using "Crank Puller" for bolt
001-6244 - ISIS 118 L EXERCISE BOTTOM BRACKET INSTALL/ REMOVAL
DETAILS
To Install: This side has Left Hand Threads. Tighten using a
purchased "AM BB ISIS DRIVE Tool" turning Hub Counter clockwise
until flange Face is completely flush with bike frame hub. Use
"LOCTITE 243 BLUE" while installing for thread locking.
To Remove: use "AM BB ISIS DRIVE Tool" and turn clockwise to loosen
threads. Note: This may take some pressure due to thread locking
material used previously.
Jam Nut
000-6244
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS Customer Service & Parts 800/ 235-2233 General Parts
Requests:
[email protected] Warranty Field Service Requests:
[email protected] Med-Fit Systems, Inc. 800/
831-7665
www.medfitsystems.com
57-0482
10-4040
Note: Belt Tension 110-120 lbs.
57-0482
73-1206 BLACK
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS
www.medfitsystems.com
40654 x 13
901-5496 x 2
40654 x 3
12-7501
57-0542- Black 000-6252 - Gray
57-0541 - Black 000-6251 - Gray
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS Customer Service & Parts 800/ 235-2233 General Parts
Requests:
[email protected] Warranty Field Service Requests:
[email protected] Med-Fit Systems, Inc. 800/
831-7665
www.medfitsystems.com
SM40235 SM40236 57-0355
12-6180
Red: PAINTED ITEMS
All labeled components are to be assembled 1. before shipment
unless otherwise noted. 2. All bearings are to be pressed in with
force applied to outer ring only. 3. All hardware to be torqued to
specs listed in chart below. 4. Special notes if any are shown
below.
Blue: KITS
www.medfitsystems.com
57-0568 57-0567 08-5186
57-0566 Zinc Plated
03-4036 x 2
02-3021 x 2
12-1380 12-7500902-5681 X 4
001-0391 Silver Paint
000-6324 Silver Paint
73-1206 BLACK
40654 x 13
901-5496 x 2
40654 x 3
SM17787
57-0542 - Black 000-6252 - Gray 57-0541 - Black
000-6251 - Gray
57-0611 12-6180
57-0355
09-8080
57-0350-05 (Australian)
PART NO. Default - Top Level/QTY. DESCRIPTION
000-6207 2 END CAP 000-6244 1 ISIS TRUVATIV 118MM X 160MM BB
000-6264 1 SEAT, MED WIDTH 000-6324 1 CRANK ARM LEFT HAND 001-0391
1 CRANK ARM RIGHT HAND 001-0424 1 WATER BOTTLE HOLDER 001-0458 1
DECAL, WARNING, U/R916 001-6347 1 KEYPANEL, OVERLAY, RIGHT 001-6365
2 DISC, CRANK 01-4113 2 Button HD Joint Connector, 3/8-16 X 1.06
01-4126 10 BOLT BH ,¼ -20 x ½'' SS BLACK 02-3058 4 SCREW #8-32 X 1
PHIL PAN HEAD ZINC 02-3062 8 #6 -32 UNC THREAD x 1" OVAL HEAD
PHILLIPS M/S
_SS-BLACK OXIDE 02-4130 2 SCREW, SET, ¼ -20 UNC x ½ 02-4174 10
SCREW SHCS , ¼ -20 UNC x ½ Zinc 02-9306 6 M5 X 0.8 X 80M Philipps
Pan Head Screw 02-9307 4 SCREW, M6-1.0 X 20mm L, SHCS, STAINLESS
03-3043 4 5/16" Lock Nut 03-4031 6 8-32 INSERT HEX 03-4034 10 10-32
INSERT HEX 03-4036 8 RIVNUT 10-32 NF, .125-.225 04-2021 2 WASHER,
FLAT, 3/8" USS 05-5130 2 IGUS FLANGE .5 ID x .5938 OD x .25L
05-5146 3 EB-TENSIONER BRACKET MOUNT BUSHING 07-1156 2 6204-2z Ball
Bearing Double Sealed 08-5186 1 SPACER NYLON 5/8 DIA X 1/2 L
09-8080 1 TYRAP, .14 X 11.0 10-4040 1 LeeSpring-LHL750A 07 12-1151
2 DECAL SEAT ADJUSTMENT 1-13 R10 12-1380 1 Made In USA 12-1822 1
Honix Console Decal 12-5621 2 NLS ONE 3” Dome Decal (000-6491)
12-6180 1 Decal, Parts Diagram Schematic U10 12-6304 1 DECAL, U10
"E-BRAKE TECHNOLOGY" LEFT 12-6305 1 DECAL, U10 "E-BRAKE TECHNOLOGY"
RIGHT 12-6308 1 Membrane Switch Overlay for Honix Display 12-7500 1
MPale Antimicrobial Label 12-7501 1 Caution 15V and 4A 12-8005 1
DECAL SEAT ADJUSTMENT 1-4 U10 19-1013 1 TAPE DBL SIDED 2 3/4" WIDE
19-1043 1 U10 Quick Assembly Instructions (Hardcopy Printed)
19-6000 1 DVD Technical Documentation 27592 3 WASHER, M8, SPLIT
LOCK 40654 28 SCREW, #10-32 X .75, PAN HEAD, W/LOCK WASHER 56-0584
2 Wheel (56-0580 Drilled Out to .641 ID) 56-0585 2 Wheel Sleeve
(for 56-0584) 56-0587 1 SPRING GAS LOCKING IN COMPRESSION 100N
57-0350 1 Power Adaptor, 15VDC, 4A 57-0355 1 BATTERY 12V 1.3 Ah
57-0373 1 PULLEY 8 GROOVE 11 3/4" DIA 57-0376 1 DC BLOWER FAN
ASSEMBLY 57-0388 1 Seat Slide Cap 1 ½ x 3 Rect 57-0389 1 Seat Slide
guide 1 ½ x 3 Rect 57-0391 2 BUSHING SEAT SHOCK MOUNT 57-0465 1 H10
Console ATSC DOM TV KIT 10" 57-0469 1 CABLE POWER INPUT E10, U10
57-0478 1 Assembly Cable Contact Heart Rate 57-0479 1 BELT J Groove
8 Rib 63" / Drive belt U10 57-0482 1 Eddy Brake/Gen with clutch
(FB62HA21) 57-0485 1 Lower Control Board, BLCB011 57-0487 1 BRACKET
POWER INLET 57-0497 4 SPACER, #10 SCREW, 5/16" 57-0507 1 Board
Interface to Lower Control 57-0511 1 EB-COMPRESSION SPRING
RETAINING BRACKET 57-0536 1 TV Cable Assembly, E/U/R 10 Series
57-0537 1 CABLE ASSY, T-BAR GRIP TO CONSOLE, RoHS 57-0538 1
ASSEMBLY FAN INPUT POWER CABLE R10, U10 57-0541 1 U10 MAIN SHROUD,
LEFT 57-0542 1 U10 MAIN SHROUD, RIGHT 57-0545 2 GRIP CHR /ROC TOP
ASSEMBLY 57-0546 2 GRIP CHR TOP ASSEMBLY 57-0547 4 GRIP CHR BOTTOM
ASSEMBLY 57-0554 1 CABLE, Console to LCB, R10, U10 57-0555 1 INLET
COVER U10 BLACK 57-0557 1 Mast Shield Right Side
57-0562 1 CABLE, Intermediate Board to BCLB002, E10, U10, R10
57-0563 1 CABLE, Intermediate Board to BCLB002 57-0566 1 SEAT
LOCKING HEX NUT 57-0567 1 SEAT LOCKING STOP PLATE 57-0568 1 NYLON
SEAT LOCK 57-0574 1 Handle with 3/8"-16 Threaded Stud 57-0608 1
I-POD MOUNT 57-0611 1 Pocket, Peel & Stick, Cardio Schematic
70-1208 1 ASSEMBLY, FRAME U10 BIKE 71-1203 1 Weldment Front Display
Mast U10 Bike 72-1213 1 Weldment Seat Handle 73-1206 1 EB BELT
COMPRESSION SPRING TENSIONER 75-1205 1 Weldment Seat Adjustment
Vertical 75-1207 1 SEAT MOUNT SLIDE ASSEMBLY 75-1208 1 Seat Slide
Housing Bracket 899-0004 1 DECAL SERIAL/COMPLIANCE U9/U10 901-5496
2 SCW-PHP #10-32x1.25 SS 902-4707 4 SCREW SHCS, M6-1.0 X 10, SHCS,
BLACK, EPOXY 902-5681 7 SCW-SHCS M8-1.25x25 SS 91-999 1 Paint (1.5
lbs) 95-0614 L 1 PEDAL EXERCISER JD-48-A 9-16 LEFT 95-0614 R 1
PEDAL EXERCISER JD48-A 9/16 RIGHT 95-9004 1 Packaging Kit Estimate
U10 SM000-6218 1 ASSEMBLY, HANDLEBAR SM001-6348 1 KEYPANEL,
OVERLAY, LEFT SM002-0540 2 PCB, CHR INTER-CONNECT SM13180 4 CAP,
LEVELING SUPPORT SM17686 4 PAD, LEVELING SM17787 2 CONNECTOR, RF,
3MM, F SM21607 2 TAPE, DOUBLE SIDED, FOAM SM27579 4 WASHER, M6,
FLAT, ZINC PLATED SM40235 1 FASTENER, HOOK SM40236 1 FASTENER, HOOK
SM41269 2 Grommet, 2879, 7/8" ID
U10 U10 Upright Bike
www.medfitsystems.com12-6180 REV F
GENERATOR CABLE, 3 PIN SUPPLIED WITH 57-0482.
BRAKE CABLE, 2 PIN SUPPLIED WITH 57-0482
57-20008 HR SENSOR
FAN (57-0376)
(CN2)
www.medfitsystems.com REV F