Information is Tyco Confidential & Proprietary - Do Not Reproduce or Distribute

Fiber OSP Products for Graybar

Presented by:

Craig RayApplications Engineering Manager

August 4, 2006

Greg Pierce – Product Manager(FOSC 450, AirFOSC, FibrBox, Fiber Drop Repair)

Amy Schwirian – Product Manager(FTERM)

David Braga – Product Manager(CSX-2, Splitters)

August 4, 20062

Telecom Outside Plant

• World’s largest supplier of Telecom Outside Plant products

• FOSC (Fiber Optic Splice Closures) and accessories

• FibrBox, Fiber Drop Repair, FTERM, TX & IS Shelves

• CSX-2 Splitter Cabinet, Splitters

August 4, 20063

FOSC (Fiber Optic Splice Closures)

Greg Pierce – Product Manager

Wide range of closures for most all Telecom Outside Plant needs:

• Hermetically sealed FOSC® Closures:

– FOSC 400 – Heat Shrink Sealing technology

– FOSC 450, 500, 600 – Gel Sealing Technology

• Free breathing FOSC Closures:

– Air FOSC (Gel sealing around cable entry)

• Fiber Drop Repair Splice Closure

• Full line of accessories

August 4, 20064

Full Range of Closure ProductsSingle and Mass Fiber Management

Cable Sealing TechnologyHeat Shrink Gel

Butt FOSC 400-Size ASize BSize D

FOSC 450Size A

Size BSSize BSize D

In-Line XAGA FOSCFITS FOSC

Fiber Drop Repair

FOSC 500Size AASize B

*FOSC 600Size CSize D

Air FOSCSize ASize B

Fiber Drop Repair* In-line or Butt configuration

August 4, 20065

Gel cable sealing technology

• Conforms to wide ranges of shapes and sizes of cable

• Flexible in wide temperature ranges

• Gel withstands harsh chemical environments

• Cold Sealed…no heat gun required

FOSC 450 Gel Sealed Closures

August 4, 20066

FOSC 450 Closure Features• Dome-ended, butt style closures

• Variety of sizes for wide range of applications

• Re-entry accomplished in 7 seconds with dome to base clamp.

• Cable sealing accomplished by easy to use, wrap-around gel seal

• Gel under compression accomplished by simply tightening the gel block tail

• Can be re-entered and re-used over and over

August 4, 20067

The FOSC 450 Family

• FOSC 450 D6 (576 splice capacity w/basket)

• FOSC 450 B6 (144 splice capacity w/basket)

• FOSC 450 BS (144 sp. cap. w/basket. Short length)

• FOSC 450 A4 (Up to 96 splice capacity)

All products use standard building block components and practices to minimize training and improve quality

Big

Small

FOSC 450 D6

FOSC 450 A4

August 4, 20068

FOSC 450 Multi-Drop Kits

• Multiple small or drop cable installations in a single port

• Fits all FOSC 450 Closures

• 2 Versions:- 3-Drop (Quick Install) Version

- 4-Drop (Gel Wrap) Version

August 4, 20069

FOSC 450D Split Base

• Provides upgrade or rehab capabilities to any existing closure when combined with standard 450 D closure

• Provides wraparound capabilities

• Available alone, or in a FOSC 450D closure kit

August 4, 200610

AIR FOSC Closure

Aerial, Free Breathing Splice Closure

• In-Line and Taut Sheath Capability

• 2 Sizes Available:

– AIR FOSC A30.5 inches long

– AIR FOSC B• 39 inches long• Taut sheath capability

August 4, 200611

AIR FOSC Closure

• Splice Capacity: 96 single splices or 288 mass fusion splices

• Slack Storage capacity: Up to 10 ft (120 inches) of loose buffer tube or ribbon

• Gel end pieces prevents water and dust ingress

• Removable outer body for better access

• Interior frame features:- Removable splice tray holder

- Powder coated frame

- 6 strength member retention claps –“bottle caps”

August 4, 200612

FIBRBox Fiber Pedestal Enclosure

• Rugged housing

• Grommeted/gasketed door and cable entry ports

• Up to 96 splices, 4 feeder cables, 16 drops

• Mounts in pedestals, on poles, or walls (additional mounting bracket available)

• Hinging, removable splice trays

• Removable cable entry plates for fast cable/drop installation

• Removable door with security screw

August 4, 200613

FIBRBox Mounting Options

Flush Mount

• Flush Mount

• Wall/Pole Mount Bracket

• Side Mount Bracket

Flush Mount

August 4, 200614

Fiber Drop Repair Closure

• Heat-shrink and cold-sealed versions available

• Taught sheath design

• Designed for single or ribbon splice – multiple loose fibers should be ribbonized

• Low cost

• Splice stand accessory available

August 4, 200615

FTerm UMT: Stubbed Terminal Applications

• Terminals can be located between the fiber distribution hub and the subscriber for a Plug-N-Play solution

– 4, 6, 8, and 12 port sizes available

– Factory Pre-stubbed – 50 ft to 200 ft standard length increments available

– Splice the stub cable to a main distribution cable

• Designed and tested for the Outside Plant environment using proven Tyco Electronics/ Raychem technology (Tested to Telcordia GR-771 and “PFOC”

Amy Schwirian – Product Manager

August 4, 200616

Product Dimensions

Ports Terminal Style Dimensions (LxWxH)4* Narrow, 2x2 9.4" x 3.4" x 2.8"

6* Narrow, 2x3 12" x 3.4" x 2.8"

8* Narrow, 2x4 14.6" x 3.4" x 2.8"

12 Wide, 4x3 12" x 6" x 3"

* Narrow designs compact enough to fit into a 4 inch duct

August 4, 200617

CSX-2 288 & 576

• Pivoting 36 Fiber Shelf

• Double Doors (<17”)

• Pad & Pole Mount Designs

• Front Access w/ Rear Cable Compartment Access

• Full Bend Radius Controls

• Upgradeable w/ Field Installed Shelves

• Field Replaceable Sides, Doors and Lid

David Braga – Product Manager

August 4, 200618

CSX-2 Functional Block Diagram

xxFeeder

Cable DistributionCable

1xn

CSX-2 Cabinet

SpliceTray

SpliceTray

InputShelf

SplitterModule

OutputShelf

x = Fusion Splice= Mated Connectors

Pigtail

Pigtail

Pigtail Storage

= Unmated Connector

August 4, 200619

CSX-2 Modular Pivoting Shelf• Accessibility of connectors both front and

rear allows easy cleaning of rear connectors

• 36 SC/APC connectors per distribution shelf

• Optional splice tray available in shelf for repair splicing

• Ribbon fanouts from shelf route to lower splice rays for factory or field stub cable splicing

• Radius control added for side exiting pigtails

• Extended base support bracket prevents pigtail “sag” from getting pinched in the shelf below and protects pigtails from front impact.

• Removable bulkhead panel

August 4, 200620

OCM5 Splitter Module & Pigtail Storage

• Module capacity for 1pc 2x32, 2pc 2x16, 4pc 2x8

• Fits all CSX-2 Cabinets

• 16 port connector retainer - connector is protected and “captured”

• Dust cap stays on the ferrule for endfaceprotection

• Mounted above shelves

• Minimal initial Routing/Plug-in

• Easy accessibility and routing of pigtails

• Storage area in cabinet for 4 to 8 splitters

August 4, 200621

CSX-2 288 Cabinet

August 4, 200622

CSX-2 144

• September ’06 Product Release

• Pivoting 36 Fiber Shelf

• 72 Fiber Shelf Assembly (2x36 fiber shelves) is Pre-Stubbed and Field Installable

• Gel Cable Seal

• Pad & Pole Mount Designs

• Total Front Access

• Simplified Pigtail Management

• 19” Internal Frame Structure

• Removable Outer Shell

• Side Mount Ground Bar / Toning Access

August 4, 200623

CSX-2 144 Key Cabinet Components

Splitter Module Mounting Area(5 Module Capacity)

36 Fiber Output Shelves (4x)

12 - 24 Fiber InputShelf (1x)

Cable Sealing Bracket(4 Cable Capacity)

Splitter Pigtail Parking Lots(64 Port Capacity)

Pad MountSkirt (10” height).

Pigtail Management/Routing Area

Ground Bar Access Panel – Side Mount

August 4, 200624

Configurations, Dimensions, Weights

Approximate Dimensions

H x W x D (in)

144 Pad/Pole 5 64 12 R or LT 2x72 R or LT 33.5 x 21.25 x 15 105288 Pad/Pole 10 128 24 R or LT 288 R or LT 49 x 23.5 x 15 145576 Pad 20 256 48 R or LT 2x288 R or LT 49 x 48 x 15 325

Notes: 1. Configuration offerings are subject to change.2. Dimensions and weights are estimated for some cabinet configurations. Weights do not include cable stubs or packaging.3. Stub cables may be Ribbon (R) or Loose Tube (LT) deigns.4. Pad mount configurations include a 9" skirt height.5. CXS-2 splitter modules are described in Tyco Electronics' OCM5 data sheet

Standard Distribution Cable

Stub

Weight (lbs) Color

Almond

Application

Splitter Module

Mounting Capacity

Splitter Port Storage Capacity

Standard Feeder Cable

Stub

Cabinet Size /CustomerCapacity

August 4, 200625

CSX-2 Requirements / Specifications

• CSX-2 Cabinet: RUS Bulletin 1753F-302 (PE-91)

• Splitter Modules: Tyco Electronics RUD 5330

• Connectors/Adapters: Telcordia GR-326, Issue 3

August 4, 200626

Splitter Products

Splitter Applications in FTTx

August 4, 200627

Splitters Types• Split Optical Power – Better Utilization of Equipment and Fiber in the PON

• Types: Fused Fiber (FBT) and Planar Circuit (PLC)

• Sizes: 1x2 thru 2x32

• FBT Features:– Low Loss– Good Uniformity– Best Price (1x2 – 1x8)– Built with Concatenated 1x2’s

• PLC Features:– Lower Loss– Improved Uniformity– Best Price (1x16 – 1x32)

FBT Splitters

PLC Splitters

August 4, 200628

Splitter Packaging

• Splitters Provided In …– FOSC Trays (A or D)– FIST Trays (SOSA)

• Connectorized Modules Also Available (CSX and CSX-2 Cabinets)

• FOSC and FIST Trays can be Applied to Closures, Shelves, Cabinets

August 4, 200629

Splitter (Rack Mounted Designs)

OCFPS Optical Component Front Patching Shelf

• Central Office / Headend Applications• LAN’s• Network Monitoring• 19” Rack Mount Ready• Connectorized FBT and PLC Splitter

Types • 1x2 through 2x32 Split Ratios• Low Loss Splitters Available• SC, SC/APC, LC, FC, FC/APC Connector

Types Available

OCM Optical Component Module

• Splitter Modules for LGX Chassis

August 4, 200630

NEXG Networks – 144 Splice/Patch

OSP 144fX

F-IS Splice Shelf144 fiber splice capacity

TX3 Patch Shelf (2x)72 fiber patch capacity ea.

Pigtails to Equipment

12, 12f IFC Cables SC/APC Connectors

Recommended Shelf Configurations: (see datasheets)F-IS3-IXNA-12LA-NNNNF-TX3-IBSA-CAB6-3012

Note: F-TX…“3012” is a custom part name for this application

Customer should confirm ordering information per datasheets

August 4, 200631

IS Shelves• Function

Splicing OSP Cable to Inter-Facility Cable (IFC)

• CapabilitiesFOSC 400 Fiber Management System, Snap-in Hinging Trays. Shelf fits 19” and 23” racks.

• SplicingOSP to IFC, OSP to IFC Pigtail, IFC to IFC Pigtails, OSP to OSP

• CapacityShelf -144 single fusion splicesTray - 12 single fusion splices or 6 mass

fusion splices

• DimensionsH x W x D: 5” x 17.5” x 11”

August 4, 200632

TX Shelves

• FunctionConnectorized Termination Point for Fiber Optic Cables

• CapabilitiesTray is field re-configurable for patching or splicing on either end of the tray. The TX tray is also reversible. Open access to both sides of removable adapters. Shelf fits into 19” and 23” racks.

• Shelf CapacityPatching - Up to 72 jumper-jumper

- Up to 6 IFC 12 Fiber Cables Splicing - Up to 72 single fusion splices to

pigtails (6 trays per shelf)

• DimensionsH x W x D: 1.8/3.3/5” x 17.5” x 11”

August 4, 200633

Technical Support ContactsWestern Regional Sales Manager

• Ted Dolmat (626) 297-7078

Customer Service Representative

• Lisa Russell (919) 557-2106

Product Managers:

• Greg Pierce – Closures (919) 557-8524

• Amy Schwirian – FTERM (919) 557-8779

• David Braga – CSX Cabinets (919) 557-8416

Applications Engineering Manager

• Craig Ray (919) 557-8679