Two-WayRadio Model MT 800 ENGLISH - Walkie-talkie · – Press and hold the LIGHT/MAX RANGE button for at least five (5) seconds until you hear two (2) beeps, indicating that the

Product Features• Two-Way Radio

with up to a 5 km (3 mile) range• 8 Channels*• 38 CTCSS Privacy Codes• 83 DCS Privacy Codes• Backlit LCD Display• Battery Saver Circuitry• Maximum Range Extender• VOX Mode for Hands-Free Transmissions• Baby Monitor Function• Call Alert (10 Selectable Tones)• Scan (Channel, Privacy Code)• Dual Watch Programmable 2-Location Scan• Key Lock• Auto Squelch• Selectable On/Off "Roger Beep"

Confirmation Tone• Selectable On/Off Keystroke Tone• Combination Speaker/Microphone/Charging Jack• Belt Clip*You are not allowed to use channels 1 and 2 in France.This situation can change; please contact the French radio licensingauthority for more information.

ENGLISH

Two-Way Radio Model MT 800

Prin

ted

inCh

ina

Part

No.4

80-3

32-P

Vers

ion

A

1

CHRG

1. Antenna2. External Speaker/

Microphone/Charge Jack3. Mode/Power Button4. Lock Button5. Channel Control Buttons6. Speaker/Microphone7. Light/Max Range Button8. Volume Control Buttons9. Talk Button10. Call Button11. Belt Clip12. Battery Compartment13. Lock Tab

8

2

4

5

9

7

10

6

3

11

12

13

13

1211

10

9

7

5

14

12 3

1. Dual Watch Icon2. Scan Icon3. Roger Beep Icon4. DCS Icon5. Keystroke Tone Icon6. Lock Icon7. VOX Icon

8. CTCSS Icon9. Baby Monitor Icon10. Battery Low Icon11. Privacy Code Numbers12. Power Saver Icon13. Main Channel Number14. Receive/Transmit Icon

64

8

NOTE: Estimated operation timeon full charge: 12 hours.

These rechargeable batteriesmust be recycled or disposedof properly in compliance withall applicable laws. They mustnot be thrown in the rubbish bin. Some countriesand local authorities require recycling and haveestablished collection programs. Please contactyour local waste disposal authority for instructions.WARNING: Do not put batteries into fire or expose

to high heat. They may explode.For Charging microTALK® Radio(s):1. Check to see that the batteries have been

inserted properly. Seeabove for batteryinstallation instructions.

2. Insert round connector ofwall charger into thecharge jack located at thetop of the radio. The wallcharger has two (2) roundconnectors which enablesyou to charge either oneor two (2) radios at a time.

3. Plug the wall charger into electrical outlet.It is not recommended to recharge batteries morethan 24 hours. Estimated operation time on a fullcharge is 12 hours.Use only the supplied rechargeable batteries andwall charger for recharging your microTALK®

radio. Non-rechargeable alkaline batteries can alsobe used.

OPERATION

Product InformationThis microTALK® radio has been manufactured tomeet all required standards for radio equipmentusing PMR 446 frequencies as authorized. Theuse of this two-way radio product involves thepublic airways and its use may be subject to locallaws or regulations. Contact your radio licensingauthority for more information.

Caring for Your RadioYour microTALK® radio will give you years oftrouble-free service if cared for properly. Here area few suggestions:• Handle the radio gently.• Keep it away from dust.• Never put the radio in water or in a damp place.• Avoid exposure to extreme temperatures.Charger and RechargeableBatteriesTo Insert Batteries inRadio:1. Remove belt clip by

releasing belt clip latch andsliding clip up.

2. Pull up on lock tab toremove battery cover (onback of radio).

3. Insert batteries according topolarity markings.

English

Each port can charge one radio. Uses 230-voltadaptor.Cobra recommends your radio is turned Off whilebeing charged.

Radio PowerTo Turn Your Radio On:Press and hold theMODE/POWER button untilyou hear a series of audibletones indicating that the radiois On.Your microTALK® radio is now in LISTENING MODE,ready to receive transmissions. The radio is alwaysin LISTENING MODE, except when the TALK, CALLor MODE buttons are pressed.To Turn Your Radio Off:– Press and hold the POWER button.

Battery Low IndicatorWhen battery power is low,the BATTERY LOW indicatorwill blink, indicating thatbatteries should be rechargedor replaced.WARNING: Only the supplied

NiMH batteriescan be recharged.

Battery/Power SaverIf there are no transmissionswithin 10 seconds, the unitwill automatically switch toBattery Save Mode andPOWER SAVER will appear inthe display. This will not affect the unit’s abilityto receive incoming transmissions.

Communicating withAnother Person1. Press and hold the TALK

button.2. With the microphone about

5 cm (2 inches) from yourmouth, speak in a normalvoice.

3. Release the button whenyou have finished talkingand listen for a response.

You cannot receive incomingcalls while pressing the TALK button.NOTE: Both radios must be tuned to the same

channel and privacy code to communicate.

Remove Belt Clip

Mode/Power Button

Lock Tab

Insert Batteries

5 cm (2 Inches)From Mouth

Talk Button

Battery Low

Power Saver

Wall Charger

Insert Connector

OPERATION

Listening for aResponseRelease the TALK button toreceive incoming transmissions.Your microTALK® is always inLISTENING MODE except whenthe TALK, CALL or MODEbuttons are pressed.

To Adjust VolumePress the VOLUME UP or theVOLUME DOWN buttons.A double beep sound is used toindicate that you have reachedthe minimum (1) or maximum(8) volume level.

Call ButtonPress and release the CALLbutton.The other person will hear atwo (2) second ringing tone.You cannot receive transmissions while sending acall.NOTE: Both radios must be tuned to the same

channel and privacy code to communicate.

English

To Illuminate DisplayPress and release theLIGHT/MAX RANGE button toilluminate the display for 10seconds.

Auto Squelch/Maximum Range ExtenderYour microTALK® radio is equipped with AutoSquelch, which automatically shuts off weaktransmissions and unwanted noise resulting fromterrain, conditions, or from reaching yourmaximum range limit.You can temporarily turn Off Auto Squelch or turnOn Maximum Range Extender, allowing all signalsto be received and extending the maximum rangeof your radio.To Temporarily Turn Off Auto Squelch:– Press the LIGHT/MAX

RANGE button for less thanfive (5) seconds.

If you hear two (2) beeps,you have turned theMaximum Range Extender On(see below).

ChannelsWith the radio ON, select anyof the 8 channels by pushingthe CHANNEL UP or CHANNELDOWN button.You can press and hold theCHANNEL UP or CHANNELDOWN button for fast advance.NOTE: Both radios must be

tuned to the samechannel and privacycode (see “CTCSS Privacy Codes” or “DCSPrivacy Codes”) to communicate.

Lock FunctionThe LOCK button locks the CHANNEL UP, CHANNELDOWN, and MODE/POWER buttons to preventaccidental operation.To Use the Lock Function:– Press and hold the LOCK

button for two (2) secondsto turn the Lock On or Off.

A double beep sound is used toconfirm your Lock On or Offrequest. When the radio is inLock Mode, the Lock icon willbe displayed.

To Turn Maximum Range Extender On:– Press and hold the LIGHT/MAX RANGE button

for at least five (5) seconds until you hear two(2) beeps, indicating that the Maximum RangeExtender is On.

To Turn Maximum Range Extender Off:– Press and release the LIGHT/MAX RANGE

button or change channels.

microTALK® RangeYour microTALK® radio has a range of up to 5kilometres (3 miles). Your range will varydepending on terrain and conditions.

In flat, open country, yourradio will operate atmaximum range.Buildings and foliage in thepath of the signal canreduce the range.Dense foliage and hillyterrain will further reducethe signal.

Remember, you can achievemaximum range by usingMaximum Range Extender.See above for details.

Light/Max RangeButton

Call Button

Lock Button

Channel Buttons

Channels

Lock Icon

Volume Level

Volume Buttons

Light/Max RangeButton

Maximum Range

Reduced Range

Reduced Range

Listening

OPERATION andMODE FUNCTIONS

External Speaker/Microphone/Charge JackYour microTALK® radio can befitted with an externalspeaker/microphone, freeingyour hands for other tasks.To Attach the ExternalSpeaker/Microphone orCharger:1. Open the charge tab on top of the radio.2. Insert the plug into the jack.Earbud Microphone1. Plug earbud microphone into

radio.2. Place earbud in ear.3. Clip microphone onto

clothing 76 mm to 152 mm(3" to 6") from your mouth.

4. Push to talk.

English

To Select a CTCSS PrivacyCode:1. After selecting a channel,

press and release theMODE button until theCTCSS icon flashes on thedisplay. In addition to theCTCSS icon, either OFF orthe small numbers next tothe channel number willalso flash on the display.

2. If CTCSS and OFF areflashing, press the CHANNELUP or CHANNEL DOWNbutton to exit OFF andproceed to select a privacycode. Or, if CTCSS and thesmall numbers next to thechannel number areflashing, press the CHANNELUP or CHANNEL DOWN button to select aprivacy code.

3. When your desired privacy code is displayed,choose one of the following:a. Press the MODE button to enter the new

setting and proceed to other functions.b. Press the LOCK button to enter the new

setting and return to LISTENING MODE.c. Do not press any buttons for 15 seconds to

enter the new setting and return toLISTENING MODE.

Scrolling Through the ModeFunctionsBy scrolling through the Mode Functions, you willbe able to select or change preferred features ofyour microTALK® radio. While you are scrollingthrough the Mode Functions, your radio featureswill be displayed in the same predetermined order:

Set CTCSS Privacy CodesSet DCS Privacy CodesSet VOX On/OffSet VOX Sensitivity LevelSet Channel ScanSet CTCSS Privacy Code ScanSet DCS Privacy Code ScanProgram Dual Watch Location or

Set Dual Watch On/OffSet Baby MonitorSet Call TonesSet “Roger Beep” On/OffSet Keystroke Tones On/Off

CTCSS Privacy CodesCTCSS (Continuous Tone Coded Squelch System) isan advanced tone coding system allowing you toselect one of 38 privacy codes to reduce incomingtransmissions from other users on the channel.NOTE: If you are using a CTCSS privacy code, both

radios must be tuned to the same channeland CTCSS privacy code to communicate.Each channel will remember the last privacycode you selected.

DCS Privacy CodesDCS (Digital Coded Squelch) isan advanced digital codingsystem allowing you to selectone of 83 privacy codes toreduce incoming transmissionsfrom other users on thechannel.NOTE: If you are using a DCS

code, both radios mustbe tuned to the samechannel and DCS privacycode to communicate.Each channel willremember the lastprivacy code youselected.

To Select a DCS PrivacyCode:1. After selecting a channel,

press and release the MODE button until theDCS icon flashes on the display. In addition tothe DCS icon, either OFF or the small numbersnext to the channel number will also flash onthe display.

2. If the DCS and OFF are flashing, press theCHANNEL UP or CHANNEL DOWN button to exitOFF and proceed to select a privacy code. Or, ifDCS and the small numbers next to thechannel number are flashing, press theCHANNEL UP or CHANNEL DOWN buttonto select a privacy code.

Mode Button

Select Privacy Code

Channel Buttons

Select Privacy Code

Mode Button

CHRG

External Speaker/Microphone/Charge Jack

Clipped to Clothing

Placed in Ear

Radio Charger Jack1

2

3

Clipped to Clothing4

Channel Buttons

CTCSS OFF

DCS OFF

MODE FUNCTIONSOPERATION

3. When your desired privacy code is displayed,choose one of the following:a. Press the MODE button to enter the new




Voice Activated Transmit (VOX)In VOX Mode, your microTALK® radio can be used“hands-free,” automatically transmitting when youspeak. You can set the VOX sensitivity level to fitthe volume of your voice and avoid transmissionstriggered by background noise.To Turn VOX Mode On orOff:1. Press the MODE button until

the VOX icon flashes on thedisplay. The current On orOff setting is displayed.

2. Press the CHANNEL UP orCHANNEL DOWN button toturn VOX On or Off.

3. When your desired VOXMode setting is displayed,choose one of thefollowing:

English

Channel ScanYour microTALK® radio can automatically scanchannels (1 to 8).NOTE: The radio ignores specific CTCSS or DCS

privacy codes while scanning channels.To Scan Channels:1. Press the MODE button until

the Scan icon and thechannel number flash onthe display.

2. Press the CHANNEL UP orCHANNEL DOWN button tobegin scanning channels.

The Scan icon will continue tobe displayed when channelscan is On. Your radio willcontinue to scan all channelsand stop if an incomingtransmission is detected. Yourradio will remain on thatchannel for 10 seconds.While setting channel scan, if you do not pressany buttons for 15 seconds your radio willautomatically return to LISTENING MODE on thechannel or channel/privacy code displayed beforeyou entered Mode Functions.

a. Press the MODE button to enter the newsetting and proceed to other functions.

b. Press the LOCK button to enter the newsetting and return to LISTENING MODE.

c. Do not press any buttons for 15 seconds toenter the new setting and return toLISTENING MODE.

To Set the VOX Sensitivity Level:1. Press the MODE button until

the VOX icon flashes andthe current sensitivity levelis displayed.

The current sensitivity level isdisplayed with the letter “L”and a number 1 to 5, 5 beingthe most sensitive level and 1being the least sensitive level.2. Press the CHANNEL UP or

CHANNEL DOWN button tochange the setting.

3. When your desired VOXsensitivity level is displayed,choose one of thefollowing:a. Press the MODE button to enter the new




During An Incoming Transmission,You Can Choose From The Following:

a. Press and hold the TALK button tocommunicate on that channel. Your radio willremain on that channel and return toLISTENING MODE.

b. Press the CHANNEL UP or CHANNEL DOWNbutton to resume scanning channels.

If you press the TALK button while scanning andnot within 10 seconds of receiving a transmission,you will transmit on the channel on which you lastreceived a transmission. This will return the radioto LISTENING MODE.If you do not press any button within 10 seconds,your radio will automatically resume scanningchannels.During Scanning (while not receivinga transmission), You Can Choose FromThe Following:

a. Press and hold the TALK button tocommunicate on either the channel orchannel/privacy code that was displayedbefore you entered Mode Functions or thechannel on which, during scanning, you lastreceived a transmission. This will return theradio to LISTENING MODE.

b. Press the MODE button to proceed to setprivacy code on the channel that was eitherdisplayed before you entered Mode Functionson which, during scanning, you last received atransmission (see “CTCSS Privacy Code Scan”or “DCS Privacy Code Scan” for further details).

Mode Button

Channel Buttons

Select Scan Channels

Channel Buttons

Select VOX

Mode Button

Channel Buttons

Select VOXSensitivity Level

Mode Button


c. Press the LOCK button to return toLISTENING MODE on either the channel orchannel/privacy code that was displayedbefore you entered Mode Functions or thechannel on which, during scanning, you lasttransmitted or received.

CTCSS Privacy Code ScanYour microTALK® radio can automatically scanthe CTCSS privacy codes (01 to 38) within one(1) channel.To Scan Privacy Codes:1. While in LISTENING MODE,

press the CHANNEL UP orCHANNEL DOWN button tochoose the channel onwhich you wish to scan theCTCSS privacy codes.

2. Press the MODE button untilthe Scan icon and the smallnumbers next to thechannel number flash onthe display.

3. Press the CHANNEL UP orCHANNEL DOWN button tobegin scanning CTCSSprivacy codes within thechannel you selected.

English

If you do not press any button within 10 seconds,your radio will automatically resume scanningCTCSS privacy codes.During Scanning (while not receivinga transmission), You Can Choose FromThe Following:

a. Press and hold the TALK button tocommunicate on either the channel orchannel/privacy code that was displayedbefore you entered Mode Functions orchannel/privacy code on which, duringscanning, you last received a transmission.This will return the radio to LISTENINGMODE.

b. Press the MODE button to proceed to nextavailable Mode Function.

c. Press the LOCK button to return toLISTENING MODE on either the channel orchannel/privacy code that was displayedbefore you entered Mode Functions or thechannel/privacy code on which, duringscanning, you last received a transmission.

DCS Privacy Code ScanYou can automatically scan the DCS privacy codes(01 to 83) within one channel.

The Scan icon will continue to be displayed whenCTCSS privacy code scan is On. Your radio willcontinue to scan CTCSS privacy codes and stop asan incoming transmission is detected. Your radiowill remain on that channel/privacy code for 10seconds.While setting CTCSS privacy code scan, if you donot press any buttons for 15 seconds your radiowill automatically return to LISTENING MODE onthe channel/privacy code that was displayedbefore you entered Mode Functions.During An Incoming Transmission,You Can Choose From The Following:

a. Press and hold the TALK button tocommunicate on that channel/privacy code.Your radio will remain on thatchannel/privacy code and returnto LISTENING MODE.

b. Press the CHANNEL UP or CHANNEL DOWNbutton to resume scanning CTCSS privacycodes.

If you press the TALK button while scanningand not within 10 seconds of receivinga transmission, you will transmit on thechannel/privacy code on which you last receiveda transmission. This will return the radio toLISTENING MODE.

To Scan DCS PrivacyCodes:1. While in the LISTENING

MODE, press the CHANNELUP or CHANNEL DOWNbutton to choose thechannel on which you wishto scan the DCS privacycodes.

2. Press the MODE button untilthe SCAN icon, DCS iconand the small numbers nextto the channel number flashon the display.

3. Press the CHANNEL UP orCHANNEL DOWN button tobegin scanning DCS privacycodes within the channelyou selected.

The scan icon will continue tobe displayed when DCS privacycode scan is ON. Your radio will continue to scanDCS privacy codes and stop when an incomingtransmission is detected. The radio will remain onthat channel/privacy code for 10 seconds.While setting DCS privacy code scan, if you do notpress any buttons for 15 seconds your radio willautomatically return to LISTENING MODE on thechannel/privacy code that was displayed beforeyou entered more functions.

Select Scan PrivacyCodes

Mode Button

Select Channel

Channel Buttons

Select Scan PrivacyCodes

Mode Button

Select Channel

Channel Buttons


During Scanning (While Receiving anIncoming Transmission), You Can Choosefrom the Following:

a. Press and hold the TALK button tocommunicate on that channel/privacy code.Your radio will remain on thatchannel/privacy code and return toLISTENING MODE.

b. Press the CHANNEL UP or CHANNEL DOWNbutton to resume scanning DCS privacycodes.

If you press the TALK button while scanning andnot within 10 seconds of receiving a transmission,you will transmit on the channel/privacy code onwhich you last received a transmission. This willreturn the radio to LISTENING MODE.During Scanning (While Not Receivingan Incoming Transmission), You CanChoose from the Following:

a. Press channel/privacy code that wasdisplayed before you entered ModeFunctions or channel/privacy code on which,during scanning, you last received atransmission. This will return the radio to theLISTENING MODE. Press and hold the TALKbutton to communicate on either thechannel or channel MODE.

b. Press the MODE button to proceed to nextavailable Mode Function.

English

Dual WatchDual Watch allows you to simultaneously monitorany two (2) Dual Watch Locations:

Dual Watch Location 1 – is always thechannel/privacy code displayed beforeyou entered Mode Functions. See“Channels,” “CTCSS Privacy Codes” and“DCS Privacy Codes” sections for furtherdetails.

Dual Watch Location 2 – will be stored in theradio. It can be edited and/or recalled forfuture engagements of Dual Watch Mode.

To Program Or Edit Dual WatchLocation 2 And EngageDual Watch Mode:1. Press the MODE button until

the Dual Watch icon and thechannel number flash onthe display.

2. Choose one of thefollowing:a. Select or edit a channel:

1) Press the CHANNELUP or CHANNELDOWN button toselect a channel(1 to 8).

c. Press the LOCK button to return toLISTENING MODE on either the channel orchannel/privacy code that was displayedbefore you entererd Mode Functions or thechannel/privacy code on which, duringscanning, you last received a transmission.

b. Select or edit a channel/privacy code:1) Press the CHANNEL UP or CHANNEL

DOWN button to select a channel(1 to 8).

2) Press the MODE button to set thechannel. The small numbers next to thechannel number will flash on the display.

3) Press the CHANNEL UP or CHANNELDOWN button to select a CTCSS privacycode (01 to 38) or DCS privacy code(01 to 83).

3. Press the LOCK button toset Dual Watch Location 2and engage DUAL WATCHMODE (see below forfurther details).

NOTES: To terminate Dual Watch and proceedto the next available Mode Function,press the MODE button.While setting Dual Watch Location 2,if you do not press any buttons for 15seconds your radio will automaticallyreturn to LISTENING MODE on Dual WatchLocation 1.

Lock Button

Select Dual Watch

Mode Button

Channel Buttons


To Turn Dual Watch On:NOTE: Dual Watch Location 2 must be

programmed to turn Dual Watch on.1. Set the first Dual Watch

Location (channel/privacycode) you wish to monitor(see “Channels,” “CTCSSPrivacy Codes” and “DCSPrivacy Codes” sections forfurther details).

2. Press the MODE button untilthe Dual Watch icon and thechannel number flash onthe display.

NOTE: While setting Dual Watch, if you do notpress any buttons for 15 seconds your radiowill automatically return to LISTENINGMODE on the last channel orchannel/privacy code displayed before youentered Mode Functions.

3. Press the LOCK buttonto engage DUAL WATCHMODE.

English

During Dual Watch (while not receivinga transmission), You Can Choose FromThe Following:

a. Press and hold the TALK button tocommunicate on either Dual Watch Location1 or the last Dual Watch Location on which,during Dual Watch, you last received atransmission. This will return the radio toLISTENING MODE.

b. Press the MODE button to proceed toother functions.

c. Press the LOCK button to return toLISTENING MODE on either Dual WatchLocation 1 or the last Dual Watch Locationon which, during Dual Watch, you lastreceived a transmission.

To Terminate Dual Watch:Choose one of the following:

a. Press the LOCK button to return toLISTENING MODE on either Dual WatchLocation 1 or the last Dual Watch Locationon which, during Dual Watch, you lastreceived a transmission.

b. Press the TALK button to return toLISTENING MODE on either Dual WatchLocation 1 or the last Dual Watch Locationon which, during Dual Watch, you lastreceived a transmission.

c. Press the MODE button and proceed to thenext available Mode Function.

During An Incoming Transmission,You Can Choose From The Following:

a. Press and hold the TALK button tocommunicate on that Dual Watch Location.Your radio will remain on that Dual WatchLocation and return to LISTENING MODE.

b. Press the CHANNEL UP or CHANNEL DOWNbutton to resume Dual Watch.

If you press the TALK button while in Dual Watchand not within 10 seconds of receiving atransmission, you will transmit on the last DualWatch Location on which you received atransmission. This will return the radio toLISTENING MODE.If you do not press any button within 10 seconds,your radio will automatically resumeDual Watch.

Baby MonitorWith the Baby Monitor Function on, a radio leftnear a baby will transmit to another unit on thesame channel and privacy code whenever a soundis detected. Baby Monitor uses the samesensitivity level you set for the VOX Function. Ifyou have not set a VOX sensitivity level (see the“Voice Activated Transmit [VOX]” section of thismanual), the maximum sensitivity, level 5, willautomatically be used.To Turn Baby Monitor On:1. Press MODE button until the

Baby Monitor icon flasheson the display. The currentOff setting is displayed.

2. Press the CHANNEL UP orCHANNEL DOWN button tochange the setting to On.

3. Press the LOCK button toenter the On setting andenter BABY MONITOR MODE.

NOTES: Pressing the MODEbutton will enter theBaby Monitor Modesetting as Off andproceed to otherMode Functions.

Mode Button

Lock Button

Channel Buttons

Select Baby Monitor

Mode Button

Select Channel

Lock Button

Not pressing any buttons for 15 secondswill enter the Baby Monitor Mode settingas Off and return the radio to LISTENINGMODE.

NOTE: Both radios must be tuned to the samechannel and privacy code to communicate.

To Terminate Baby Monitor Mode:Choose one of the following:

a. Press the TALK button and return toLISTENING MODE.

b. Press the LOCK button and return toLISTENING MODE.

c. Press the MODE button and proceed tothe next available Mode Function.

10 Call Tone SettingsYou can choose between 10 different call tonesettings to transmit a uniquecall alert.To Change a Call ToneSetting:1. Press the MODE button

until the letter “C” and thecurrent call tone number(1 to 10) is displayed. Thecurrent call tone will soundfor two (2) seconds.

2. Press the CHANNEL UPor CHANNEL DOWN buttonto hear the other calltone settings.

"Roger Beep" Confirmation ToneYour listener will hear an audible tone whenyou release the TALK button. This alerts the otherparty that you have finished talking and that it isOK for them to speak. This feature can be turnedOn or Off.To Turn “Roger Beep” On or Off:When you turn On your microTALK® radio for thefirst time, “Roger Beep” will be On.1. Press and release the MODE

button until the “RogerBeep” icon flashes on thedisplay. The current On orOff setting is displayed.

2. Press the CHANNEL UP orCHANNEL DOWN button toselect “Roger Beep”On or Off.

3. When your desired RogerBeep Mode setting isdisplayed, choose oneof the following:a. Press the MODE button

to enter the new setting and proceedto other functions.

b. Press the LOCK button to enter the newsetting and return to LISTENING MODE.

c. Do not press any buttons for 15 seconds toenter the new setting and return toLISTENING MODE.

3. When your desired call tone setting isdisplayed, choose one of the following:a. Press the MODE button to enter the new




The setting you select will be saved when youturn your radio off and on again. When the“Roger Beep” is On, the “Roger Beep” iconwill be displayed.

MODE FUNCTIONSOPERATION English

Call Tone Setting

Mode Button

Channel Buttons

Channel Buttons

Select Roger Beep

Mode Button

EnglishD.O.C., WARRANTY& CUSTOMER SERVICE

Keystroke TonesWith Keystroke Tones turned On, your radio willsound beeps each time you press a button orchange a setting.To Turn Keystroke Tones On or Off:When you turn On your microTALK® radio for thefirst time, Keystroke Tones will be On.1. Press the MODE button until

the Keystroke Tones iconflashes on the display. Thecurrent ON or OFF settingis displayed.

2. Press the CHANNEL UP orCHANNEL DOWN button toturn Keystroke Tones Onor Off.

3. When your desired Keystroke Tone Modesetting is displayed, choose one of thefollowing:a. Press the MODE button to enter the new

setting and return to LISTENING MODE.b. Press the LOCK button to enter the new



The setting you select will be saved when youturn your radio off and on again. When KeystrokeTones are On, the keystroke tone icon willbe displayed.

EnglishMODE FUNCTIONSOPERATION

Select Keystroke

Mode Button

Channel Buttons

Declaration of ConformityThis declaration is the responsibility of the manufacturer/importer

Cobra Electronics Europe LimitedDungar HouseNorthumberland AvenueDun LaoghaireCounty Dublin, Ireland

Date: 15 January 2007This certifies that the following designated product

PRIVATE MOBILE RADIO: MT 800(Product Identification)

complies with the essential protection requirements of R & TTEDirective 1999/5/EC on the approximation of the laws of theMember States relating to Radio Spectrum Matters, EMC andElectrical Safety.This declaration applies to all specimens manufactured in accordancewith the attached technical documentation described in Annex II ofthe Directive which forms part of this declaration.Assessment of compliance of the product (class 2.6) with therequirements relating to the essential requirements according toArticle 3 R & TTE was based on Annex IV of Directive 1999/5/ECand the following standards:

Radio Spectrum: EN 300 296-1 V1.1.1 (2001-03)EN 300 296-2 V1.1.1 (2001-03)

EMC: EN 301 489-1 V1.5.1 (2004-11)EN 301 489-5 V1.3.1 (2002-08)

Electrical Safety: EN 60950-1:2001 + A11:2004RF Exposure: EN 50392 (2004-02)

DUBLIN, IRELAND MIKE KAVANAGH

Warranty & Customer ServiceFor warranty and customer service information,please contact your local dealer.

For use in EU countries, subject to local laws andregulations.

CEEL® is a registered trademark ofCobra Electronics Europe, Ltd.

Snake design and microTALK® are registeredtrademarks of Cobra Electronics Corporation, USA.

©2007 Cobra Electronics Europe LimitedDungar House, Northumberland AvenueDun Laoghaire, County Dublin, Ireland

www.cobra.com

ATBABEBGCHCYCZ

DE

This equipment is intended for use in:

Countries of use

EEESFI

FR

GB GR

HRHUIEIS

LTNL

NO PL PT

RORSSESISKTR

LVLILU

ME

DK MK

MTIT

Documents

Two-WayRadio Model MT 800 ENGLISH - Walkie-talkie · – Press and hold the LIGHT/MAX RANGE button for at least five (5) seconds until you hear two (2) beeps, indicating that the