Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
TURCKDieguard Sensors
3 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
ifferential Travel (Hysteresis)
Embeddable construction includes a metal bandthat surrounds the ferrite core and coilarrangement. This helps to “bundle” or direct theelectro- magnetic field to the front of the sensor.
Figure 1Embeddable
(Shielded Sensor)
Figure 2Nonembeddable
(Nonshielded Sensor)
Nonembeddable sensors do not have this metalband; therefore, they have a longer operatingdistance and are side sensitive.
The difference between the “operate” and“release” points is called differential travel(See shaded area in Figure 3).It is factory set at less than 15% of theeffective operating distance.Differential travel is needed to keepproximity sensors from “chattering” whensubjected to shock and vibration, slowmoving targets, or minor disturbances suchas electrical noise and temperature drift.
Figure 3
Actuation Mode
Inductive sensors can be actuated in an axial or lateral approach (See Figure 3). It is important to maintain an air gap betweenthe target and the sensing face to prevent physically damaging the sensors.
Embeddable (Shielded) vs. Nonembeddable (Nonshielded)
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 4
Uprox Characteristics
• No Correction Factor - Same rated operating distance for all metals.
• Extended Operating Distance - Up to 400% greater than standard inductive sensors when using non-ferrous targets (Figure 4).
• Weld Field Immunity - Uprox is unaffected by strong electromagnetic AC or DC fields because of its unique patented design.
• High Switching Frequencies - Up to 10 times faster than standard inductive sensors.
• Extended Temperature Range - Uprox can withstand temperatures up to 85°C (+185°F) with a ±15% temperature drift.
Figure 4
Operating Principle Uprox
UproxNi12U-M18-..
StandardNi 8-M18-..
Figure 5
Operating distances comparison of Uproxsensors and standard inductive sensors.
TURCK Uprox is a patented next generation developmentof inductive sensors that uses a three-coil system. One coilinduces eddy currents on the metal target and the othertwo coils are affected by these eddy currents. Ferrous andnonferrous metals have the same effect on the two coils.Therefore, all metals, including galvanized metals, have thesame rated operating distance.
TURCK standard inductive sensors use a single coilrandomly wound around a ferrite core. The single coil bothinduces eddy currents on the metal target and is affectedby these eddy currents. Ferrous and nonferrous metalsaffect the sensor differently, making it impossible to detectboth types of metals at the same rated operating distance.
StandardSensor
Uprox
TURCKDieguard Sensors
5 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Operating Distance (Sensing Range) Considerations
Figure 6
Standard Target
The assured actuating range is between 0 and 81% of the rated operating distance. It is the range within which the correctoperation of the proximity sensor under specified voltage and temperature ranges is assured.
A square piece of mild steel having a thickness of 1 mm (0.04 in) is used as a standard target to determine the followingoperating tolerances. The length and width of the square is equal to either the diameter of the circle inscribed on theactive surface of the sensing face or three times the rated operating distance Sn, whichever is greater.
The operating distance (S) of the different models is basically a function of the diameter of the sensing coil. Maximumoperating distance is achieved with the use of a standard or larger target. Rated operating distance (Sn) for each model isgiven in the manual. When using a proximity sensor the target should be within the assured range (Sa).
The operating distance is the distance at which the target approaching the sensing face along the reference axis causes theoutput signal to change.
The rated operating distance is a conventional quantity used to designate the nominal operating distance. It does not takeinto account either manufacturing tolerances or variations due to external conditions such as voltage and temperature.
The effective operating distance is the operating distance of an individual proximity sensor at a constant rated voltage and23°C (73°F). It allows for manufacturing tolerances.
The usable operating distance is the operating distance of an individual proximity sensor measured over the operatingtemperature range at 85% to 110% of its rated voltage. It allows for external conditions and for manufacturing tolerances.
Operating Distance = S
Rated Operating Distance = Sn
Effective Operating Distance = Sr 0.9 Sn ≤Sr ≤1.1Sn
Assured Operating Range = Sa 0 ≤Sa ≤0.81Sn
Usable Operating Distance = Su 0.81 Sn ≤Su ≤1.21Sn
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 6
Notes:
TURCKInductive Sensors
7 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Selection Guide
Housing Styles Pages
Rectangular Style
9 - 11
Smooth Barrel Style
12 - 14
Threaded Barrel Style
15 - 18
Side Sensing Style
18
Ring Sensing Style
19
Note: All dimensions in this manual are shown as: inches [mm]
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 8
Sensor Selection Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Number
Embeddable vs. Nonembeddable . . . . . . . . . . . . . . . . . . . . 3
Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . 4
Operating Distance Considerations . . . . . . . . . . . . . . . . . . . 5
Q5.5 Rectangular Style, Plastic . . . . . . . . . . . . . . . . . . . . 9
Q06 Rectangular Style, Plastic . . . . . . . . . . . . . . . . . . . . . 9
Q6.5 Rectangular Style, Plasic . . . . . . . . . . . . . . . . . . . . . 9
Q08 Rectangular Style, Metal . . . . . . . . . . . . . . . . . . . . . 10
Q8SE Rectangular Style, Metal . . . . . . . . . . . . . . . . . . . . 11
Q9.5 Rectangular Style, Plastic . . . . . . . . . . . . . . . . . . . . 11
Q10S Rectangular Style, Plastic . . . . . . . . . . . . . . . . . . . . 11
CA4080 Rectangular Style, Metal . . . . . . . . . . . . . . . . . . . . 11
CA40130 Rectangular Style, Metal . . . . . . . . . . . . . . . . . . . 11
Barrels, Metal with Quick Disconnect . . . . . . . . . . . . . . . . 13 - 14, 16 - 18
Barrels, Side Sensing with Potted-in Cable . . . . . . . . . . . . . . . . . 18
Barrels, Metal with Potted-in Cable. . . . . . . . . . . . . . . . . . 12 - 13, 15
Rectangular Ring Style Plastic . . . . . . . . . . . . . . . . . . . . . 19
Dimensional Diagrams . . . . . . . . . . . . . . . . . . . . . . 21 - 25
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . 27
Sensor Activation Point Graphs . . . . . . . . . . . . . . . . . . . 28 - 34
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - 37
TURCKDieguard Sensors
9 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Q5.5 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 2-Q5.5-AN6X M1613100
PNPDiagram B
Bi 2-Q5.5-AP6XBi 2-Q5.5-AP6X/S34 2)
M1613000M1613001See Drawing #1
Q5.5
Q5.5 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3.5 mm (.138)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Ni 3.5-Q5.5-AN6X M4613610
PNPDiagram B Ni 3.5-Q5.5-AP6X M4613601
Q06 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
NPNDiagram A Bi 3-Q06-AN6X2 M1620150
PNPDiagram B Bi 3-Q06-AP6X2 M1620100See Drawing #2
Q06
Q6.5 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1 mm (.039)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 0
NPNDiagram A Bi 1-Q6.5-AN6 M4613420
PNPDiagram B
Bi 1-Q6.5-AP6Bi 1-Q6.5-AP6/S34 2)
M4613400M4613401See Drawing #3
Q6.5
Q6.5 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 0
NPNDiagram A Ni 2-Q6.5-AN6 M4613520
PNPDiagram B
Ni 2-Q6.5-AP6Ni 2-Q6.5-AP6/S34 2)
M4613500M1650023
Notes:1. Uprox technology. Sense all metals at the same range. Inherently weld-field immune.2. “/S34” designates weld-field immune sensor.3. All products available with Normally Closed output. Consult TURCK.4. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
Rectangular Style
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 10
Q08 with Snap-lock picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 5..)· · · 5 mm (.197)Sensing Range (Bi 7..)· · · 7 mm (.276)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
NPNDiagram C
Bi 5U-Q08-AN6X2-V1131 1)
Bi 5-Q08-AN6X2-V1131Bi 7-Q08-AN6X2-V1131
M1608910M1600600M1601622
PNPDiagram D
Bi 5U-Q08-AP6X2-V1131 1)
Bi 5-Q08-AP6X2-V1131Bi 7-Q08-AP6X2-V1131
M1608900M1600500M1601602
Q08-ES with Amphenol Connector (31-342-RFX) Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 5..)· · · 5 mm (.197)Sensing Range (Bi 7..)· · · 7 mm (.276)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
Analog Bi 3-Q08-ES-0.2/S1027 M1044691
Notes:1. Uprox technology. Sense all metals at the same range. Inherently weld-field immune.2. “/S34” designates weld-field immune sensor.3. All products available with Normally Closed output. Consult TURCK.4. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #5
Q08
Q08 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 5..)· · · 5 mm (.197)Sensing Range (Bi 7..)· · · 7 mm (.276)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
NPNDiagram A
Bi 5U-Q08-AN6X2 1)
Bi 7-Q08-AN6X2M1608911M1601620
PNPDiagram B
Bi 5U-Q08-AP6X2 1)
Bi 5-Q08-AP6X2/S34 2)
Bi 7-Q08-AP6X2
M1608901M1600800M1601600 See Drawing #4
Q08
Rectangular Style
See Drawing #8
Q08-ES
Q08-ES with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 5..)· · · 5 mm (.197)Sensing Range (Bi 7..)· · · 7 mm (.276)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
Analog Bi 3-Q08-ES-0.2Bi 3-Q08-ES-1.22
M1044601M1044602
Q08 with threaded picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 5..)· · · 5 mm (.197)Sensing Range (Bi 7..)· · · 7 mm (.276)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
NPNDiagram C
Bi 5-Q08-AN6X2-V2131Bi 7-Q08-AN6X2-V2131
M1600602M1601623
PNPDiagram D
Bi 5-Q08-AP6X2-V2131Bi 7-Q08-AP6X2-V2131
M1600502M1601603
See Drawing #7
Q08-ES
See Drawing #6
Q08
To be used only with Weldotron® Microscan
To be used only with Weldotron® Microscan
TURCKDieguard Sensors
11 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Rectangular Style with minifast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 20 mm (.787)Power Supply· · · · · · · 20-250 VAC· · · · · · · · · · · · · · 10-300 VDC (4-wire)Number of LEDs · · · · · 2
ACDiagram G
Bi20-CA4080-ADZ30X2-B1131Bi20-CA40130-ADZ30X2-B1131/S1009
T4283400T4283503
Notes:1. “/S34” designates weld-field immune sensor.2. All products available with Normally Closed output. Consult TURCK.3. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #13 & 14
CA4080
Rectangular Style with Potted-In Cable Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (4-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 2-Q10S-AN6X S1619310
PNPDiagram B Bi 2-Q10S-AP6X S1609360See Drawing #12
Q10S
Rectangular Style with Potted-In Cable Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 0
PNPDiagram B Ni 2-Q9.5-AP6/S34 1) M1650077
See Drawing #11
Q9.5
Rectangular Style
Q8SE with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 2 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 2-Q8SE-AN6X M1619320
PNPDiagram B Bi 2-Q8SE-AP6X M1619330
See Drawing #9
Q8SE
Q8SE with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 2 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Bi 2-Q8SE-AN6X-V1131 M1619321
PNPDiagram D Bi 2-Q8SE-AP6X-V1131 M1619331
See Drawing #10
Q8SE
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 12
EH04 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1 mm (.039)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 1-EH04-AN6X S4609640
PNPDiagram B Bi 1-EH04-AP6X S4609540
See Drawing #15
EH04
EH6.5 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A
Bi 1.5-EH6.5-AN6XBi 2-EH6.5-AN6X
S4612100S4612300
PNPDiagram B
Bi 1.5-EH6.5-AP6XBi 2-EH6.5-AP6X
S4612000S4612200 See Drawing #16
EH6.5
EH6.5 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Ni 3-EH6.5-AN6X S4612500
PNPDiagram B Ni 3-EH6.5-AN6X S4612500
See Drawing #17
EH6.5
EH6.5K with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A
Bi 1.5-EH6.5K-AN6XBi 2-EH6.5K-AN6X
S4610640S4610100
PNPDiagram B
Bi 1.5-EH6.5K-AP6XBi 2-EH6.5K-AP6X
S4610540S4610000 See Drawing #18
EH6.5K
EH6.5K with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Ni 3-EH6.5K-AN6X S4610300
PNPDiagram B Ni 3-EH6.5K-AN6X S4610300
Notes:1. All products available with Normally Closed output. Consult TURCK.2. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #19
EH6.5K
Smooth Barrel Style
TURCKDieguard Sensors
13 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
EH08 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1.5 mm (.059)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 1.5-H08-AN6X S1614300
PNPDiagram B Bi 1.5-H08-AP6X S1604300
See Drawing #20
EH08
Smooth Barrel Style
EH08K with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Ni 2-H08K-AN6X S1614700
PNPDiagram B Ni 2-H08K-AP6X S1604700
See Drawing #22
EH08 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Ni 3-H08-AN6X S1614900
PNPDiagram B Ni 3-H08-AP6X S1604900
See Drawing #21
EH04 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1 mm (.039)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Bi 1-EH04-AN6X-V1331 S4608540
PNPDiagram D Bi 1-EH04-AP6X-V1331 S4608440
See Drawing #23
EH04
EH6.5 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C
Bi 1.5-EH6.5-AN6X-V1131Bi 2-EH6.5-AN6X-V1131
S4612120S4612320
PNPDiagram D
Bi 1.5-EH6.5-AP6X-V1131Bi 2-EH6.5-AP6X-V1131
S4612020S4612220
Notes:1. All products available with Normally Closed output. Consult TURCK.2. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
H08
H08K
See Drawing #24
EH6.5
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 14
EH6.5 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Ni 3-EH6.5-AN6X-V1131 S4612520
PNPDiagram D Ni 3-EH6.5-AP6X-V1131 S4612420
EH6.5K with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C
Bi 1.5-EH6.5K-AN6X-V1131Bi 2-EH6.5K-AN6X-V1131
S4610840S4610120
PNPDiagram D
Bi 1.5-EH6.5K-AP6X-V1131Bi 2-EH6.5K-AP6X-V1131
S4610740S4610020 See Drawing #26
Smooth Barrel Style
EH6.5K with picofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Ni 3-EH6.5K-AN6X-V1131 S4610320
PNPDiagram D Ni 3-EH6.5K-AP6X-V1131 S4610220
H08K with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1.5 mm (.059)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Bi 1.5-H08K-AN6X-V1131 S1604340
PNPDiagram D Bi 1.5-H08K-AP6X-V1131 S1604330
H08K with picofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Ni 2-H08K-AN6X-V1131 S1614800
PNPDiagram D Ni 2-H08K-AP6X-V1131 S1604800
Notes:1. All products available with Normally Closed output. Consult TURCK.2. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #29
See Drawing #25
See Drawing #27
See Drawing #28
EH6.5
EH6.5K
EH6.5K
H08K
H08K
TURCKDieguard Sensors
15 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
EG05 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1 mm (.039)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 1-EG05-AN6X S4609840
PNPDiagram B Bi 1-EG05-AP6X S4609740
EG05
EG08 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A
Bi 1.5U-EG08-AN6X 1)
Bi 1.5-EG08-AN6XBi 2-EG08-AN6X
S4600510S4602340S4602140
PNPDiagram B
Bi 1.5U-EG08-AP6X 1)
Bi 1.5-EG08-AP6XBi 2-EG08-AP6X
S4600500S4602240S4602040See Drawing #31
EG08
EG08 with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range (Ni 3..) · · 3 mm (.118)Sensing Range (Ni 3..) · · 4 mm (.157)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A
Ni 3-EG08-AN6XNi 4U-EG08-AN6X 1)
S4602840S4600610
PNPDiagram B
Ni 3-EG08-AP6XNi 4U-EG08-AP6X 1)
S4602740S4600600See Drawing #32
EG08
See Drawing #30
Threaded Barrel Style
EG08K with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A
Bi 1.5-EG08K-AN6XBi 2-EG08K-AN6X
S4669140S4669500
PNPDiagram B
Bi 1.5-EG08K-AP6XBi 2-EG08K-AP6X
S4669040S4669400
See Drawing #33
EG08K
EG08K with Potted-In Cable Connection Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Ni 3-EG08K-AN6X S4669700
PNPDiagram B Ni 3-EG08K-AP6X S4669600
Notes:1. Uprox technology. Sense all metals at the same range. Inherently weld-field immune.2. All products available with Normally Closed output. Consult TURCK.3. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #34
EG08K
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 16
EG05 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1 mm (.039)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Bi 1-EG05-AN6X-V1331 S4608740
PNPDiagram D Bi 1-EG05-AP6X-V1331 S4608640 See Drawing #35
EG05
EG08 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C
Bi 1.5U-EG08-AN6X-V1131 1)
Bi 1.5-EG08-AN6X-V1131Bi 2-EG08-AN6X-V1131
S4600530S4602350S4602150
PNPDiagram D
Bi 1.5U-EG08-AP6X-V1131 1)
Bi 1.5-EG08-AP6X-V1131Bi 2-EG08-AP6X-V1131
S4600520S4602220S4602050 See Drawing #36
EG08
EG08 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range (Ni 3..) · · 1.5 mm (.118)Sensing Range (Ni 4..) · · 4 mm (.157)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C
Ni 3-EG08-AN6X-V1131Ni 4U-EG08-AN6X-V1131 1)
S4602850S4600630
PNPDiagram D
Ni 3-EG08-AP6X-V1131Ni 4U-EG08-AP6X-V1131 1)
S4602750S4600620
See Drawing #37
EG08
EG08K with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range (Bi 1.5..)· · 1.5 mm (.059)Sensing Range (Bi 2..)· · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C
Bi 1.5-EG08K-AN6X-V1131Bi 2-EG08K-AN6X-V1131
S4672540S4669550
PNPDiagram D
Bi 1.5-EG08K-AP6X-V1131Bi 2-EG08K-AP6X-V1131
S4672440S4669450
See Drawing #38
EG08K
Threaded Barrel Style
EG08K with picofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 3 mm (.118)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Ni 3-EG08K-AN6X-V1131 S4669750
PNPDiagram D Ni 3-EG08K-AP6X-V1131 S4669650
Notes:1. Uprox technology. Sense all metals at the same range. Inherently weld-field immune.2. All products available with Normally Closed output. Consult TURCK.3. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #39
EG08K
TURCKDieguard Sensors
17 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
EG08 with eurofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1.5 mm (.059)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram E
Bi 1.5U-EG08-AN6X-H1341 1) S4600550
PNPDiagram F
Bi 1.5U-EG08-AP6X-H1341 1) S4600540See Drawing #40
EG08
EG08 with eurofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 4 mm (.157)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram E Ni 4U-EG08-AN6X-H1341 1) S4600650
PNPDiagram F Ni 4U-EG08-AP6X-H1341 1) S4600640
See Drawing #41
EG08
G12 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Bi 2-G12-AN6X-V1131 T4635583
PNPDiagram D Bi 2-G12-AP6X-V1131 T4606597
See Drawing #42
G12
G12 with picofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 5 mm (197)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram C Ni 5-G12-AN6X-V1131 T4635721
PNPDiagram D Ni 5-G12-AP6X-V1131 T4635690
See Drawing #43
G12
G12 with eurofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 2 mm (.079)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram E Bi 2-G12-AN6X-H1141 T4606693
PNPDiagram F Bi 2-G12-AP6X-H1141 T4606595
Notes:1. Uprox technology. Sense all metals at the same range. Inherently weld-field immune.2. All products available with Normally Closed output. Consult TURCK.3. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #44
G12
Threaded Barrel Style
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 18
G12 with eurofast Connector Output Part Number ID #
Installation · · · · · · · · Non-Flush MountSensing Range · · · · · · 5 mm (.197)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram E Ni 5-G12-AN6X-H1141 T4635793
PNPDiagram F Ni 5-G12-AP6X-H1141 T4635692
See Drawing #45
G12
HS540 with Potted-In Cable Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1 mm (.039)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 1-HS540-AN6X S4604101
PNPDiagram B Bi 1-HS540-AP6X S4604001 See Drawing #46
HS540
HS865 with Potted-In Cable Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1.5 mm (.059)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 1.5-HS865-AN6X S4604301
PNPDiagram B Bi 1.5-HS865-AP6X S4604201 See Drawing #47
HS865
GS880 with Potted-In Cable Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 1.5 mm (.059)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram A Bi 1.5-GS880-AN6X S4604501
PNPDiagram B Bi 1.5-GS880-AP6X S4604401
Notes:1. All products available with Normally Closed output. Consult TURCK.2. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #48
GS880
Threaded & Smooth Side Sensing Barrel Styles
Threaded Barrel Styles
TURCKDieguard Sensors
19 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Q14 with Potted-In Cable Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range:
(Bi 6..) · · · · · · · · · 6.1 mm (.240)(Bi 10..) · · · · · · · · 10.1 mm (.398)(Bi 15..) · · · · · · · · 15.1 mm (.594)(Bi 20..) · · · · · · · · 20.1 mm (.791)
Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
NPNDiagram A
Bi 6R-Q14-AN6X2Bi10R-Q14-AN6X2Bi15R-Q14-AN6X2Bi20R-Q14-AN6X2
M1406020M1406120M1406220M1406320
PNPDiagram B
Bi 6R-Q14-AP6X2Bi10R-Q14-AP6X2Bi15R-Q14-AP6X2Bi20R-Q14-AP6X2
M1406000M1406100M1406200M1406300
Q20 with eurofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range · · · · · · 30.1 mm (1.185)Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 2
NPNDiagram E Bi30R-Q20-AN6X2-H1141 M1407520
PNPDiagram F Bi30R-Q20-AP6X2-H1141 M1407500
W30 with eurofast Connector Output Part Number ID #
Installation · · · · · · · · Flush MountSensing Range:
(Bi 6..) · · · · · · · · · 6.1 mm (.240)(Bi10..)· · · · · · · · · 10.1 mm (.398)(Bi15..)· · · · · · · · · 15.1 mm (.594)(Bi20..)· · · · · · · · · 20.1 mm (.791)(Bi30..)· · · · · · · · · 30.1 mm (1.185)
Power Supply· · · · · · · 10-30 VDC (3-wire)Number of LEDs · · · · · 1
NPNDiagram E
Bi 6R-W30-DAN6X-H1141Bi10R-W30-DAN6X-H1141Bi15R-W30-DAN6X-H1141Bi20R-W30-DAN6X-H1141Bi30R-W30-DAN6X-H1141
M1403700M1403900M1404100M1404300M1404500
NPNDiagram F
Bi 6R-W30-DAP6X-H1141Bi10R-W30-DAP6X-H1141Bi15R-W30-DAP6X-H1141Bi20R-W30-DAP6X-H1141Bi30R-W30-DAP6X-H1141
M1403600M1403800M1404000M1404200M1404500
Notes:1. All products available with Normally Closed output. Consult TURCK.2. Sensing range based on a target 1”x1”x1/8” cold rolled steel.
See Drawing #49
See Drawing #50
See Drawing #51
Q14
Q20
W30
Rectangular Style Ring Sensors
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 20
Notes:
TURCKDieguard Sensors
21 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
2
8
1
7
4
3
65
10
9
11 12
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 22
151413
16 1817
19 20
22
21
23 24
TURCKDieguard Sensors
23 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
26 2725
2928
31
30
33
34 35 36
32
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 24
43 4544
46 47 48
4140 42
38 3937
TURCKDieguard Sensors
25 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
50 5149
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 26
Notes:
TURCKDieguard Sensors
27 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
E NPN (Sinking) F PNP (Sourcing)
C NPN (Sinking) D PNP (Sourcing)
G Normally Open
B PNP (Sourcing)A NPN (Sinking)
3-Wire DC, Potted-In Cable Wiring Diagrams
3-Wire DC, Quick Disconnect, picofast, Wiring Diagrams
3-Wire DC, Quick Disconnect, eurofast, Wiring Diagrams
2-Wire AC/DC, Quick Disconnect, minifast, Wiring Diagrams
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 28
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCKDieguard Sensors
29 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 30
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCKDieguard Sensors
31 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 32
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCKDieguard Sensors
33 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 34
Sensor Activation Point
Red: Switch OnBlue: Switch OffGreen: CenterYellow: Sensing
TURCKSensor Accessories
35 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
PartNumber
IDNumber
Dimensions
A B C D E F G H J Probe Travel
WP-08-50-03 A2527
3.9299.6
1.2531.8
0.153.8
M8x1 .1253.2
2.0050.8
1.9549.5
.43611.1
M8x1 todepth of0.8621.8
For activation:.071(1.80) to.075(1.91)
Maximum:.080(2.03)
WP-12-50-03 A2528
M12x1
.1253.2
.62315.8
M12x1 todepth of0.7118.0
For activation:.056(1.42) to.080(2.03)
Maximum:.085(2.15)
WP-12-50-06 A2529 .2506.4
PartNumber
IDNumber
Dimensions
A B C D E F G H
DP-08-25-08 A2521
2.2557.2
1.0025.4
M8x1 0.4311.0
0.7218.4
2000 N450 lbft
0.205.08
.1152.93
DP-12-25-12 A2519 M12x1 0.6215.7
0.6717.4
20500 N4608 lbft
0.256.35
.1664.22
DP-18-25-18 A2520 M18x1 0.8722.1
0.8722.1
45000 N10115 lbft
0.256.35
.1664.22
Accessories
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 36
Bi
TURCK Part Numbers
TURCKPart Number Index
37 TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com
TURCK Part Numbers
TURCK Inc. 3000 Campus Drive Minneapolis, MN 55441 Application Support: 1-800-544-7769 Fax: (763) 553-0708 www.turck.com 38
TURCK Inc. sells its products through Authorized Distributors. These distributors provide ourcustomers with technical support, service and local stock. TURCK distributors are locatednationwide - including all major metropolitan marketing areas.
For Application Assistance or for the location of your nearest TURCK distributor, call:
1-800-544-PROX (1-800-544-7769)
Specifications in this manual are subject to change without notice. TURCK also reserves the rightto make modifications and makes no guarantee of the accuracy of the information containedherein.
Literature and Media questions or concerns?
Contact Marketing Services at TURCK USA: [email protected]
Automation Controls B0154 Proximity Sensors B2000Flow & Temperature B0155
Cordsets B2001 Capacitive Sensors B0149 multimodul B0144
New Literature from TURCK
The Industry Leader in Proximity Sensing,Cordsets and Interface Technology
Sensors DivisionSensors Catalog - B2000Flow Monitors Catalog - B0155email: [email protected]
Special Products DivisionCordsets Catalog - B2001Releco Relay Catalog - B0234email: [email protected]
Intrinsic Safety Products DivisionAutomation Controls Catalog - B0154multimodul Catalog - B0144email: [email protected]
InterlinkBTInterlinkBT Catalog - B9000Beckhoff Bus Terminal Catalog - B9005email: [email protected]
TURCK USA TURCK Canada TURCK Mexico InterlinkBTTURCK Inc.3000 Campus DriveMinneapolis, MN 55441Phone: (763) 553-7300FAX: (763) 553-0708Application Support:1-800-544-PROX (7769)
CHARTWELLELECTRONICS, INC.140 Duffield DriveMarkham, OntarioCanada, L6G 1B5Phone: (905) 513-7100FAX: (905) 513-7101
ICESA - MODICONAnt. Camino a Sta. Monica No. 7San Lucas Tepetlacalco54050 TlalnepantlaEdo. de MexicoPhone: (52) 5-397-8644FAX: (52) 5-398-9888
InterlinkBT3000 Campus DriveMinneapolis, MN 55441Phone: (763) 694-2300FAX: (763) 694-2399Application Support:1-888-546-5880
Printed in USA B1777 5/01
ProximitySensorsIndustry’s broadest line ofinductive and capacitiveproximity sensors.
FlowMonitorsMonitors for sensing theflow of liquids and gasesduring industrialprocesses.
InterlinkBTDevice-level interconnectand bus products forsensors and actuators.
Cordsetsand Junctions
Industry standard cordsetsand junction boxes
connect the most popularswitch and sensor styles.
InterfaceDevices
Interface and logicproducts for automation
and intrinsically safeenvironments.
w w w . t u r c k . c o m