18/01/08

Global Lifting Services LtdCERTIFICATE OF TEST and EXAMINATION

CLIENT :- TEST HOUSE :-SURE TANKS EXPORT Global Lifting Services Ltd

Silverburn CrescentSHAMROCK HILLBridge of DonDUNLEERAberdeenCO. LOUTHAB23 8EWREPUBLIC OF IRELAND Tel No: 01224 707585

N/A Fax No: 01224 707646CERTIFICATE No. CUSTOMER ORDER No. CUSTOMER REQUISITION No. DATE OF TEST/ EXAMINATION

45170 / 0098 1234T 18/01/08

I.D. NUMBER QTY DESCRIPTION PROOF LOADSWL/Payload

FSA458 1 FOUR LEG WIRE ROPE SLING TO WLL:DNV2.7-1:2006/AS1666 8.35 TONNELEGS 2.7MTR X 26MM DIA IWRC GALV 0-45 DEGGRADE 1960N/MM2FITTED TO A Q38B QUAD ASSEMBLYC/W HARD EYES EACH END

458A-D 4 SAFETY PIN BOW SHACKLES 8.5 TONNE

mfrost.bmp

Global Lifting Services LtdAberdeenAB23 8EWBridge of DonSilverburn Crescent01224 70758501224 707646

(a) The Lifting Operations and Lifting Equipment Regulations 1998 S.I. No. 2307

(b) The Supply of Machinery (Safety) Regulations 1992 S.I. No. 3073

(c) The Provision and Use of Work Equipment Regulations 1998 S.I. No. 2306

I hereby certify that the equipment described on this certificate has been tested, examined and found to be freefrom flaws or other defects.

FORM QAF50AREV 2

SIGNATURE :-COMPANY APPOINTED EXAMINERM.FROST

DUNLEERSURE TANKS EXPORTSHAMROCK HILLREPUBLIC OF IRELANDCO. LOUTHM.FROST

ADDRESS: 45 Eastern Road, Traralgon, VIC 3844 Australia PHONE +61 3 5174 8730 FAX +61 3 5176 4306 ALS Industrial PTY LTD ABN 21 006 353 046

This document will not be reproduced except in full

Page 1 of 1

ALS Approved Signatory: Mark Holmes

Signed:

Verified By:

Name Douglas Bell

Signed

Date 20-3-15

Accreditation No.: 218, Site No.:1572 Accredited for compliance with ISO/IEC 17025 All work is subject to our standard terms and conditions. Available on our website- http://www.alsglobal.com/industrialDownloads.aspx

EDDY CURRENT INSPECTION REPORT

Client: Ferguson Group Australia Pty Ltd 16 Alacrity Place Henderson WA 6166

Report No: 4015 0179 ET03

Location of Job: Tek Ocean Date of Inspection: 19th March 2015

Description of Job: Pad Eye Welds and Sling Ring Radii

Identification: FCB3607 / 3.6M Cargo Basket Sling I/D: FSA458

Clients Order No: FGA-PO 001628-1 Client’s Job No: N/A

Request No: N/A Requested by: J Harding (Tek Ocean)

Acceptance Spec.: N/A (Inspect for in service cracking) Surface Preparation: Painted

Material: Carbon Steel (Not further Specified)

Test Specification: ISO 17643-2005 Test Procedure: NDT.ET.002

Technicians: Mark Holmes Clients Test Requirements: ET inspection of Pad Eye Welds and Sling Ring internal radii

Equipment Used: Hocking Phasec 3d

Probes: GE 800PO1DA3S / Weld Scan (10mm 100 kHz)

Reference Standard: Fe EDM 0.5/1.0/2.0mm

Result:

An Eddy Current Inspection was carried out on Pad Eye welds and the inside radius of Sling Rings, in accordance with the above procedure

No evidence of In-Service cracking was detected

Fig 1 FCB3607 / 3.6M Cargo Basket

Fig 2 Pad eye (typical)