Kit Contents: (1) 7.5 oz. aerosol can MOTOR MEDIC® Total Intake System Cleaner, (1) 12 fl. oz. bottle MOTOR MEDIC® Fuel System Cleaner, (1) Applicator Hose, (1) Support Hook

Features:Cleans fuel injectorsEliminates knocking and pingingReduces emissionsEliminates rough idles

Benefits:Restores lost performance and powerBoosts fuel economy

Tools Needed:Safety glasses, Gloves, Pliers, Rags

Use this as a part of your 6,000 to 10,000 mile preventative maintenance schedule or when vehicle is having poor performance such as low fuel economy, rough idles or loss of performance and power.

Contact info: RSC Chemical Solutions 600 Radiator Road Indian Trail, NC 28079 877-464-4865 www.rscbrands.com

RSC Chemical Solutions®

600 Radiator RoadIndian Trail, NC 28079

877-464-4865 www.rscbrands.com

Symptom Possible Cause Action Needed

Cannot locate brake booster vacuum line.

Not sure where brake booster vacuum line is located.

Search for port location at www.fuelprocomplete.com .

Refer to vehicle maintenance manual.

Intake cleaner will not exhaust into vacuum line.

Cap not securely attached to can.

Kink in hose.

Button not depressed.

Can is not properly in hook holder.

Verify cap and hose are securely installed on can.

Verify hose is unrolled properly and does not have any kinks.

Fully depress button to lock in place.

Set can in hook holder and verify can is sitting upright (vertical).

Engine runs rough while applying intake cleaner into vacuum line.

Low RPM

Application hose not fully inserted into vacuum line.

Increase engine RPMs to 1,000 RMPs while depressing button on intake cleaner.

Verify the application hose is plugged into vacuum line during application.

Engine will not restart. Vacuum hose not plugged back into brake vacuum booster.

Other wires or hoses unplugged.

Reconnect vacuum hose back into vacuum booster.

Verify no other wires or vacuum line were knocked off during the cleaning process.

Engine runs rough during idle.

Vacuum hose not plugged back into vacuum booster.

Reconnect vacuum hose back into vacuum booster.

Check engine lights comes on.

Fuel mixture. If no lights were previously on prior to using the intake cleaner, light will go off after vehicle completes a normal drive cycle. This will vary depending on model of vehicle.

Light can also be reset at local auto parts store.

Use your own on-board diagnostics (OBD) analyzer to reset the light.

TROUBLESHOOTING

For product demo and all product information, go to: www.fuelprocomplete.com

For other MOTOR MEDIC® and RSC Chemical Solutions® products, go to: www.rscbrands.com

DANGER: EXTREMELY FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED. EYE & SKIN IRRITANT. READ PRECAUTIONS ON THE NEXT PANEL.

RMFSC6DOC

Total Intake Cleaner DANGER: CONTAINS (CAS#): Heterocyclic Amines (Proprietary), Acetonitrile (75-05-8), and Dimethyl Ether propellant (115-10-6). Extremely flammable. Harmful or fatal if swallowed. Vapor harmful — inhaling concentrated vapors, intentionally or otherwise, can be fatal. Eye and skin irritant. Keep away from heat, sparks and open flame. Do not breathe automotive exhaust vapors.

Fuel Injector Cleaner DANGER: CONTAINS (CAS#): Petroleum distillates (68476-34-6). Keep away from heat, sparks or open flame. Avoid contact with skin and eyes. Use with adequate ventilation.

STEP 1Always wear eye protection and gloves when installing this product.

Position vehicle outside in a well-ventilated area and turn off the engine.

1 Locate brake booster vacuum line at www.fuelprocomplete.com.

2 Remove vacuum line from vacuum booster.

STEP 2Empty entire contents of MOTOR MEDIC® Fuel Injector Cleaner into gas tank.

Treats up to 15 gallons of gasoline. For best results, add entire bottle to a nearly full tank. Regular use keeps fuel system clean and at peak operating efficiency.

AVOID CONTACT WITH PAINTED SURFACES. In case of paint contact, wash off with water immediately.

3 Insert aerosol multi- adapter hose tip securely into vacuum line coming from the vehicle’s brake booster.

NEVER USE A VACUUM LINE THAT IS UPSTREAM OF THE MASS AIR FLOW (MAF) SENSOR. DOING SO CAN DAMAGE THE MAF SENSOR.

4 Place MOTOR MEDIC® Total Intake System Cleaner canister in the hanging installation apparatus and connect multi-adapter hose to top of canister.

7 Depress the spray button slowly and allow the vehicle oxygen sensor to adjust for the new air to fuel mixture then depress and lock the spray button in the fully open position.

8 Allow the entire contents of the canister to empty into intake system.

9 When can is empty, turn off the engine, disconnect the multi-adapter from the vacuum source, replace the disconnected vacuum line to its original location, remove hanging installation apparatus and close hood.

DANGER: Vacuum line MUST be reconnected to vacuum brake booster after use of this product and before driving vehicle. If not, the engine will run poorly, and brake performance will also be affected, potentially resulting in injury or death. NEVER drive a vehicle with a disconnected vacuum line.

10 Start vehicle and allow to idle for 3 minutes, snapping accelerator 3 times to ensure removal of dislodged carbon particles.

NOTE: If vehicle stalls during application, simply release lock-down button on applicator and repeat installation steps 6 to 10.

NOTE: In some cases a check engine light could come on during the application of this product. If there are no pre-existing codes prior to using this kit, a soft-code can be triggered by the intake cleaning, such as a misfire. The check engine light will go off during vehicle’s basic drive cycle. Each vehicle’s manufacturer’s drive cycle may vary and could take up to 2 days. An alternative to turning off the check engine light is have it reset at your local automotive parts store at no charge.

Install hose onto canister (aerosol can): Remove applicator hose from kit and install on top of can by pressing firmly with palm of hand. Do not depress the button release until you’re ready to start the cleaning process.

WARNING: This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.

5 Safely hang installation apparatus on the underside of the vehicle hood. WARNING: DO NOT SET CAN ON ANY HOT SURFACES OR IN CONTACT WITH ANY ELECTRICAL CONNECTIONS TO PREVENT CAN BURSTING AND FLASH FIRE.

6 Start engine and bring engine to 1,000 RPM.

FIRST AID:

EYE CONTACT: Flush with water for 15 minutes while lifting eyelids and get prompt medical attention.

SKIN CONTACT: Wash with soap and water promptly. If irritation develops, get prompt medical attention.

INHALATION: Move to fresh air. If breathing becomes difficult, get prompt medical attention.

INGESTION: Do not induce vomiting. Call physician, hospital or Poison Control Center immediately.

STORAGE, HANDLING, DISPOSAL: Use only outside in a well-ventilated area. Do not puncture or incinerate container. Do not expose to heat, sparks, open flame or store at temperatures above 120°F (48°C). Dispose of residues and empty container in accordance with all local, state and federal laws and regulations. Empty containers contain product residue, so follow all warnings, even after containers are emptied. Empty aerosol cans are recyclable: consult your local recycling authority.

KEEP AWAY FROM CHILDREN AND ANIMALS