Upload
kasi-chinna
View
56
Download
1
Tags:
Embed Size (px)
Citation preview
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
1/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 1
INTRODUCTION
In search of our project we plan to do something, which is yet to be established and must be
useful to day to day life. We analyzed the current situation and realized that if there may be
system that informs the user about various faults in the transformer, we will be able to prevent
severe damages. So we decided to develop such a system that detects transformer faults.
A system which can detect the voltage of a transformer from normal to danger and to take an
initiatives to avoid damage to a transformer.
Power transformers are designed to transmit and distribute electrical power. Depending on the
size of a transformer, replacement costs can range from a few hundred dollars to millions of
dollars. Performing offline and invasive tests also add to the replacement cost. Hence, there is an
increasing need to move from traditional schedule-based maintenance programs to condition-
based maintenance. However, a focused approach is required for diagnostics.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
2/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 2
SYSTEM OVERVIEW
TRANSMITTER BOCK DIAGRAM
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
3/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 3
RECEIVER BLOCK DIAGRAM
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
4/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 4
BLOCK DIAGRAM DESCRIPTION :
Transformer fault detection includes the following components:
Power supply Microcontroller
Buzzer
LCD Display
Relay
Transformer
Mobile
Transmission lines Zigbee technology
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
5/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 5
TRANSFORMER
INTRODUCTION
The protection system of transformer is inevitable due to the voltage fluctuation, frequent
insulation failure, earth fault, over current etc. Thus the following automatic protection systems
are incorporated.
1. Buchholz devices:A Buchholz relay, also called a gas relay or a sudden pressure relay, is a safety
device mounted on some oil-filled power transformers and reactors, equipped with an
external overhead oil reservoir called a conservator. The Buchholz Relay is used as a
protective device sensitive to the effects of dielectric failure inside the equipment. Italso provides protection against all kind of slowly developed faults such as insulation
failure of winding, core heating and fall of oil level.
2. Earth fault relays:An earth fault usually involves a partial breakdown of winding insulation to earth.
The resulting leakage current is considerably less than the short circuit current. The
earth fault may continue for a long time and creates damage before it ultimately
develops into a short circuit and removed from the system. Usually provides
protection against earth fault only.
3. Over current relays:An over current relay, also called as overload relay have high current setting and
are arranged to operate against faults between phases. Usually provides protection
against phase -to-phase faults and overloading faults.
4. Differential system:Differential system, also called as circulating-current system provides protection
against short-circuits between turns of a winding and between windings that
correspond to phase-to-phase or three phase type short-circuits i.e. it provides
protection against earth and phase faults.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
6/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 6
The complete protection of transformer usually requires the combination of these
systems. Most of the transformers are usually connected to the supply system through
series fuses instead of circuit breakers. In existing method the transformer does not
have automatic protective relays for protecting the transformer.
TRANSFORMERDEFINITION
A device used to transfer electric energy from one circuit to another, especially a pair of
multiple wound, inductively coupled wire coils that affect such a transfer with a change in
voltage, current, phase, or other electric characteristic.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
7/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 7
Fig 2.1 Basic Transformer
THE UNIVERSAL EMF EQUATION
If the flux in the core is sinusoidal, the relationship for either winding between its
number of turns, voltage, magnetic flux density and core cross-sectional area is given by
the universal emf equation (from Faradays Law):
(2.1)
E is the sinusoidal rms or root mean square voltage of the winding,
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
8/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 8
f is the frequency in hertz,
N is the number of turns of wire on the winding,
a is the cross-sectional area of the core in square meters
B is the peak magnetic flux density in Tesla P is the power in volt amperes or watts,
NECESSITY FOR PROTECTION
Transformers are static devices, totally enclosed and generally oil immersed. Therefore,
chances of faults occurring on them are very rare. However, the consequences of even a rare
fault may be very serious unless the transformer is quickly disconnected from the system. This
necessitates providing adequate automatic protection for transformers against possible faults.
COMMON TRANSFORMER FAULTS
As compared with generators, in which many abnormal conditions may arise, power
transformers may suffer only from:
1. Open circuits
2. Overheating
3. Winding short-circuits
Open circuit Faults:
An open circuit in one phase of a 3-phase transformer may cause undesirable heating. In
practice, relay protection is not provided against open circuits because this condition is relatively
harmless. On the occurrence of such a fault, the transformer can be disconnected manually from
the system.
Overheating Faults:
Overheating of the transformer is usually caused by sustained overloads or short circuits
and very occasionally by the failure of the cooling system. The relay protection is also not
provided against this contingency and thermal accessories are generally used to sound an alarm
or control the banks of fans.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
9/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 9
Winding Short-circuit Faults:
Winding short-circuits (also called internal faults) on the transformer arise from
deterioration of winding insulation due to overheating or mechanical injury. When an internal
fault occurs, the transformer must be disconnected quickly from the system because a prolongedarc in the transformer may cause oil fire. Therefore, relay protection is absolutely necessary for
internal faults.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
10/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 10
MICROCONTROLLER
4.1 INTRODUCTION
Microcontroller is a microprocessor designed specifically for control applications, and is
equipped with ROM, RAM and facilities I / O on a single chip.AT89S52 is one of the family
MCS-51/52 equipped with an internal 8 Kbyte Flash EPROM (Erasable and Programmable Read
Only Memory), which allows memory to be reprogrammed.
The AT89S52 is a low-power, high-performance CMOS 8-bit microcomputer with 4Kbytes of
Flash programmable and erasable read only memory (PEROM).This device is a Single-chip 8-bit
Microcontroller and is a derivative of the 8051 microcontroller family. The instruction set is
100% compatible with the 8051 instruction set. The on-chip Flash allows the program memory
to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By
combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89S52 is a
powerful microcomputer which provides a highly-flexible and cost-effective solution to many
embedded control applications.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
11/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 11
FEATURES OF MICROCONTROLLER
A CPU (central processing unit) 8 bits.
256 bytes of RAM (random access memory) internally.
Four ports of I/O with each consist of 8 bit.
The internal oscillator and timing circuit.
Two timers/counters 16 bits.
Five interrupt lines (two fruits and three external interrupt internal interruptions).
A serial port with full duplex UART (Universal Asynchronous Receiver Transmitter).
Able to conduct the process of multiplication, division, and Boolean.
The size of 8 Kbytes EPROM for program memory.
Maximum speed execution of instructions per cycle is 0.5 s at 24 MHz clock frequency.
If the microcontroller clock frequency used is 12 MHz, the speed is 1 s instruction
execution.
CPU (central processing unit)
This section serves to control the entire operation on the microcontroller. This unit is divided into
two parts, the control unit, or CU (Control Unit) and the arithmetic and logic unit or ALU
(Arithmetic Logic Unit) The main function control unit is to take instructions from memory
(fetch) and then translate the composition of these instructions into a simple collection of work
processes (decode), and implement instruction sequence in accordance with the steps that have
been determined the program (execute). Arithmetic and logic unit is the part that deals with
arithmetic operations like addition, subtraction, and logical data manipulation operations such as
AND, OR, and comparison.
4.2.2 INPUT/OUTPUT (I/O)
This section serves as a communication tool with a single chip device outside the system.
Consistent with the name, I / O devices can receive and provide data to / from a single chip.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
12/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 12
There are two kinds of devices I / O is used, ie devices for serial connection UART (Universal
Asynchronous Receiver Transmitter) and device for so-called parallel relationship with the PIO
(Parallel Input Output).Both types of I / O has been available in a single chip AT89S52.
SOFTWARE
Single flakes MCS-51 family has a special programming language that is not understood by
other types of single flakes. This programming language known by the name of the assembler
language instruction has 256 devices. However, when this can be done with microcontroller
programming using C language. With the C language, microcontroller programming easier,
because the C language format will be automatically converted into assembler language with a
hex file format. Software on a microcontroller can be divided into five groups as follows:
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
13/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 13
PIN CONFIGURATION
AT89S52 microcontroller has 40 pins with a single 5 Volt power supply. The pin 40 is illustrated
as follows:
4.3.1 THE FUNCTION OF EACH PIN AT89S52
Vcc:Supply Voltage.
GND:Ground.
http://electricly.com/wp-content/uploads/2010/06/AT89S52-MICROCONTROLLER-configuration.jpg5/28/2018 Transformer Fault Detection Using Zigbee and GSM
14/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 14
Port 0:
Port 0 is an 8-bit open drain bi-directional I/O port. As an output port, each pin can sink eight
TTL inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs.
Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses
to external programmed data memory. In this mode, P0 has internal pull-ups. Port 0 also receives
the code bytes during Flash programming and outputs the code bytes during program
verification.
Port 1:
Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers can
sink/ source four TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the
internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally being pulled
low will source current (IIL) because of the internal pull-ups. Port 1 also receives the low-order
address bytes during Flash programming and verification.
Port 2:
Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 2 output buffers cansink/ source four TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the
internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled
low will source current (IIL) because of the internal pull-ups. Port 2 emits the high-order address
byte during fetching from external program memory and during access to external data memory
that uses 16-bit addresses (MOVX @DPTR). In this application, Port 2 uses strong internal pull-
ups when emitting 1s. During accesses to external data memory that uses 8-bit address (MOVX
@R1), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the
high-order address bits and some control signals during Flash program and verification.
Port 3:
Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 3 output buffers can
sink/ source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
15/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 15
internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled
low will source current (IIL) because of the pull-ups. Port 3 also serves the functions of
Port 3 pin alternate Functions:
P 3.0 RXD (Serial Input Port)
P 3.1 TXD (Serial Output Port)
P 3.2 INT0 (External Interrupt 0)
P 3.3 INT1 (External Interrupt 1)
P 3.4 T0 (Timer 0 External Input)
P 3.5 T1 (Timer 1 External Input)
P 3.6 WR (External Data Memory Write Strobe)
P 3.7 RD (External Data Memory Read Strobe).
Port 3 also receives some control signals for Flash programming and programming verification.
RST: Reset Input
A high on this pin for two machine cycles while the oscillator is running resets the device. This
pin drives High for 98 oscillator periods after the Watchdog times out.
ALE/PROG:
Address Latch Enable is an output pulse for latching the low byte of the address during accesses
to external memory. This pin is also the program pulse input (PROG) during Flash programming.
In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency and may be
used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped
during each access to external data memory. If desired, ALE operation can be disabled by setting
bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC
instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if
the Microcontroller is in external execution mode.
PSEN:Program Store Enable
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
16/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 16
It is the read strobe to external program memory. When the AT89S52 is executing code from
external program memory, PSEN is activated twice each machine cycle, except that two PSEN
activations are skipped during each access to external data memory.
EA/Vpp:External Access Enable/ Programming Enable Voltage
External Access Enable must be strapped to GND in order to enable the device to fetch code
from external program memory locations starting at 0000H up to FFFFH. Note, however, that if
lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to Vcc
for internal program executions. This pin also receives the 12-volt programming enable voltage
(Vpp) during Flash programming.
XTAL1:
Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
XTAL2:
It is the output from the inverting oscillator amplifier.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
17/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 17
TIMER
Timer0: 8-bit timer/counter with 8-bit prescaler
Timer1: 16-bit timer/counter with prescaler
Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler.
Mode 0: 13-Bit Timer
Lower byte (TL0/TL1) + 5 bits of upper bytes (TH0/TH1).
Backward compatible to the 8048
Not generally used
Timer operation in Mode 0
Mode 1: 16-bit
All 16 bits of the timer (TH0/TL0, TH1,and TL1) are used.
Maximum count is 65,536
At 12 MHz, maximum interval is 65536 microseconds or 65.536
milliseconds
TF0 must be reset after each overflow
THx/TLx must be manually reloaded after each overflow.
Mode 2: 8-bit Auto Reload
Only the lower byte (TLx) is used for counting.
Upper byte (THx) holds the value to reload into TLx after and overflow.
TFx must be manually cleared.
Maximum count is 256
Maximum interval is 256 Microseconds or .256 milliseconds
INTERRUPT
Hardware interrupts were introduced as a way to avoid wasting the processor's valuable time
in polling loops, waiting for external events. They may be implemented in hardware as a distinct
system with control lines, or they may be integrated into the memory subsystem.
If implemented in hardware, an interrupt controller circuit such as the IBM PC's Programmable
Interrupt Controller (PIC) may be connected between the interrupting device and the processors
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
18/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 18
interrupt pin to multiplex several sources of interrupt onto the one or two CPU lines typically
available. If implemented as part of the memory controller, interrupts are mapped into the
system's memory address space.
Interrupts can be categorized into: maskable interrupt, non-maskable interrupt (NMI), inter-processorinterrupt (IPI), software interrupt, and spurious interrupt.
Maskable interrupt(IRQ) is a hardware interrupt that may be ignored by setting a bit in
an interrupt mask register's (IMR) bit-mask.
Non-maskable interrupt(NMI) is a hardware interrupt that lacks an associated bit-mask, so
that it can never be ignored. NMIs are often used for timers, especially watchdog timers.
Inter-processor interrupt(IPI) is a special case of interrupt that is generated by one
processor to interrupt another processor in a multiprocessor system.
Software interruptis an interrupt generated within a processor by executing an instruction.
Software interrupts are often used to implement system calls because they implement a
subroutine call with a CPU ring level change.
Spurious interruptis a hardware interrupt that is unwanted. They are typically generated by
system conditions such as electrical interference on an interrupt line or through incorrectly
designed hardware.
Processors typically have an internal interrupt mask which allows software to ignore all external
hardware interrupts while it is set. This mask may offer faster access than accessing an interrupt
mask register (IMR) in a PIC, or disabling interrupts in the device itself. In some cases, such as
the x86 architecture, disabling and enabling interrupts on the processor itself act as a memory
barrier, however it may actually be slower.
An interrupt that leaves the machine in a well-defined state is called a precise interrupt. Such an
interrupt has four properties:
The Program Counter (PC) is saved in a known place.
All instructions before the one pointed to by the PC have fully executed.
No instruction beyond the one pointed to by the PC has been executed (that is no prohibition
on instruction beyond that in PC, it is just that any changes they make to registers or memory
must be undone before the interrupt happens).
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
19/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 19
The execution state of the instruction pointed to by the PC is known.
An interrupt that does not meet these requirements is called an imprecise interrupt.
The phenomenon where the overall system performance is severely hindered by excessive
amounts of processing time spent handling interrupts is called an interrupt storm.
TYPES OF INTERRUPT
LEVEL-TRIGGERED
EDGE-TRIGGERED
HYBRID
MESSAGE SIGNALED
DOORBELL
USES OF INTERRUPT
Typical uses of interrupts include the following: system timers, disks I/O, power-off signals,
and traps. Other interrupts exist to transfer data bytes using UARTs or Ethernet; sense key-
presses; control motors; or anything else the equipment must do.
A classic system timer generates interrupts periodically from a counter or the power-line. The
interrupt handler counts the interrupts to keep time. The timer interrupt may also be used by the
OS's task scheduler to reschedule the priorities of running processes. Counters are popular, but
some older computers used the power line frequency instead, because power companies in most
Western countries control the power-line frequency with a very accurate atomic clock.
A disk interrupt signals the completion of a data transfer from or to the disk peripheral. Aprocess waiting to read or write a file starts up again.
A power-off interrupt predicts or requests a loss of power. It allows the computer equipment to
perform an orderly shut-down.
Interrupts are also used in type ahead features for buffering events like keystrokes.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
20/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 20
NEED OF MICROCONTROLLER
Microcontroller is a general-purpose device which has in-built CPU memory and
peripherals to make it act as a mini-computer
Microcontroller has one or two operational codes for moving data from external to CPU
Microcontroller has many bit handling instructions
Microcontroller works faster than microprocessor because of rapid movement of bits
within the chip
Microcontroller can function as a computer with the addition of no external parts
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
21/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 21
POWER SUPPLY
INTRODUCTION
A power supply is a device that supplies electrical energy to one or more electric loads. The term
is most commonly applied to devices that convert one form of electrical energy to another,
though it may also refer to devices that convert another form of energy (e.g., mechanical,
chemical, solar) to electrical energy. A regulated power supply is one that controls the output
voltage or current to a specific value; the controlled value is held nearly constant despite
variations in either load current or the voltage supplied by the power supply's energy source.
Every power supply must obtain the energy it supplies to its load, as well as any energy it
consumes while performing that task, from an energy source. Depending on its design, a power
supply may obtain energy from:
Electrical energy transmission systems. Common examples of this include power supplies
that convert AC line voltage to DC voltage.
Energy storage devices such as batteries and fuel cells.
Electromechanical systems such as generators and alternators.
Solar power.
A power supply may be implemented as a discrete, stand-alone device or as an integral device
that is hardwired to its load. Examples of the latter case include the low voltage DC power
supplies that are part of desktop computers and consumer electronics devices.
The amount of voltage and current it can supply to its load.
How stable its output voltage or current is under varying line and load conditions.
How long it can supply energy without refueling or recharging (applies to power supplies
that employ portable energy sources)
.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
22/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 22
EXPLAINATION AND BLOCK DIAGRAM
The ac voltage, typically 220V rms, is connected to a transformer, which steps that ac
voltage down to the level of the desired dc output. A diode rectifier then provides a full-
wave rectified voltage that is initially filtered by a simple capacitor filter to produce a dc
voltage. This resulting dc voltage usually has some ripple or ac voltage variation.
A regulator circuit removes the ripples and also remains the same dc value even if the input
dc voltage varies, or the load connected to the output dc voltage changes. This voltage
regulation is usually obtained using one of the popular voltage regulator IC units.
POWER SUPPLY
Regulator
Filter
Bridge
RectifierStep down
transformer
230V
AC
D.C
Output
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
23/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 23
CIRCUIT DIAGRAM OF POWER SUPPLY
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
24/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 24
WORKING OF POWER SUPLLY
TRANSFORMER:
Usually, DC voltages are required to operate various electronic equipment and these voltages are
5V, 9V or 12V. But these voltages cannot be obtained directly. Thus the a.c input available at the
mains supply i.e., 230V is to be brought down to the required voltage level. This is done by a
transformer. Thus, a step down transformer is employed to decrease the voltage to a required
level.
RECTIFIER:
The output from the transformer is fed to the rectifier. It converts A.C. into pulsating D.C. The
rectifier may be a half wave or a full wave rectifier. In this project, a bridge rectifier is used
because of its merits like good stability and full wave rectification.
FILTER:
Capacitive filter is used in this project. It removes the ripples from the output of rectifier and
smoothens the D.C. Output received from this filter is constant until the mains voltage and load
is maintained constant. However, if either of the two is varied, D.C. voltage received at this point
changes. Therefore a regulator is applied at the output stage.
VOLTAGE REGULATOR:
As the name itself implies, it regulates the input applied to it. A voltage regulator is an electrical
regulator designed to automatically maintain a constant voltage level. In this project, power
supply of 5V and 12V are required. In order to obtain these voltage levels, 7805 and 7812
voltage regulators are to be used. The first number 78 represents positive supply and the numbers
05, 12 represent the required output voltage levels.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
25/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 25
5.5 POWER SUPPLY APPLICATION
5.5.1 Computer power supply
A modern computer power supply is a switch-mode power supply that converts AC power from
the mains supply, to several DC voltages. Switch-mode supplies replaced linear supplies due to
cost, weight, and size improvement. The diverse collection of output voltages also has widely
varying current draw requirements.
5.5.2 Welding power supply
Arc welding uses electricity to melt the surfaces of the metals in order to join them together
through coalescence. The electricity is provided by a welding power supply, and can either
be AC or DC. Arc welding typically requires high currents typically between 100 and 350 amps.
Some types of welding can use as few as 10 amps, while some applications of spot
welding employ currents as high as 60,000 amps for an extremely short time. Older welding
power supplies consisted of transformers or engines driving generators. More recent supplies
use semiconductors and microprocessors reducing their size and weight.
5.5.3 AC Adapter
A power supply that is built into an AC mains power plug is known as a "plug pack" or "plug-in
adapter", or by slang terms such as "wall wart". They are even more diverse than their names;
often with either the same kind of DC plug offering different voltage or polarity, or a different
plug offering the same voltage. "Universal" adapters attempt to replace missing or damaged
ones, using multiple plugs and selectors for different voltages and polarities. Re5lacementpower
supplies must match the voltage of, and supply at least as much current as, the original powersupply.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
26/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 26
LIQUID CRYSTAL DISPLAY
LCD (Liquid Crystal Display) screen is an electronic display module and find a wide range of
applications. A 16x2 LCD display is very basic module and is very commonly used in various
devices and circuits. These modules are preferred over seven segmentand other multi
segment LEDs. The reasons being: LCDs are economical; easily programmable; have no
limitation of displaying special & evencustom characters(unlike in seven
segments), animationsand so on.
A 16x2 LCD means it can display 16 characters per line and there are 2 such lines. In this LCD
each character is displayed in 5x7 pixel matrix. This LCD has two registers, namely, Command
and Data.
The command register stores the command instructions given to the LCD. A command is an
instruction given to LCD to do a predefined task like initializing it, clearing its screen, setting the
cursor position, controlling display etc. The data register stores the data to be displayed on the
LCD. The data is the ASCII value of the character to be displayed on the LCD.
LCDs are used in a wide range of applications, including computer monitors, television,
instrument panels, aircraft cockpit displays, signage, etc. They are common in consumer devices
such as video players, gaming devices, clocks, watches, calculators, and telephones. LCDs have
replaced cathode ray tube (CRT) displays in most applications. They are available in a wider
range of screen sizes than CRT and plasma displays, and since they do not use phosphors, they
cannot suffer image burn-in. LCDs are, however, susceptible to image persistence.
The LCD is more energy efficient and offers safer disposal than a CRT. Its low electrical power
consumption enables it to be used in battery-powered electronic equipment. It is an electronically
modulated optical device made up of any number of segments filled with liquid crystals and
arrayed in front of a light source (backlight) or reflector to produce images in color
or monochrome. The most flexible ones use an array of small pixels. The earliest discovery
leading to the development of LCD technology, the discovery of liquid crystals, dates from 1888.
By 2008, worldwide sales of televisions with LCD screens had surpassed the sale of CRT units.
http://www.engineersgarage.com/microcontroller/8051projects/create-custom-characters-LCD-AT89C51http://www.engineersgarage.com/microcontroller/8051projects/create-custom-characters-LCD-AT89C51http://www.engineersgarage.com/microcontroller/8051projects/create-custom-characters-LCD-AT89C51http://www.engineersgarage.com/microcontroller/8051projects/create-custom-characters-LCD-AT89C515/28/2018 Transformer Fault Detection Using Zigbee and GSM
27/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 27
6.2 FEATURES
5 x 8 dots with cursor
Built-in controller (KS 0066 or equivalent)
+5V power supply (also available for +3V)
1/16 duty cycle
B/L to be driven 1,pin 2 or pin 15,pin 16
N.V. optional for +3V power supply
LCD can display a character successfully by placing the
1. Data in Data Register
2.
Command in Command Register of LCD
3. Data corresponds to the ASCII value of the character to be printed. This can be done by
placing the ASCII value on the LCD Data lines and selecting the Data Register of the
LCD by selecting the RS (Register Select) pin.
4. Each and every display location is accessed and controlled by placing respective command on
the data lines and selecting the Command Register of LCD by selecting the (Register Select) RS
pin.
TABLE 1: Pin description for LCD
Pin symbol I/O Description
1 Vss -- Ground
2 Vcc -- +5V power supply
3 VEE -- Power supply to
control contrast
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
28/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 28
TYPES OF DISPLAY LCD:
Segment (or alphanumeric)
Dot matrix (or character)
Graphic LCD.
4 RS I RS=0 to select
command register
RS=1 to select
data register
5 R/W I R/W=0 for write
R/W=1 for read
6 E I/O Enable
7 DB0 I/O The 8-bit data bus
8 DB1 I/O The 8-bit data bus
9 DB2 I/O The 8-bit data bus
10 DB3 I/O The 8-bit data bus
11 DB4 I/O The 8-bit data bus
12 DB5 I/O The 8-bit data bus
13 DB6 I/O The 8-bit data bus
14 DB7 I/O The 8-bit data bus
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
29/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 29
Advantages and disadvantages of LCDs
In spite of LCDs being a well proven and still viable technology, as display devices LCDs are
not perfect for all applications.
6.5.1 Advantages
Very compact and light.
Low power consumption.
No geometric distortion.
Little or no flicker depending on backlight technology.
Not affected by screen burn-in.
Can be made in almost any size or shape.
No theoretical resolution limit.
6.5.2 Disadvantages
Limited viewing angle, causing color, saturation, contrast and brightness to vary, even
within the intended viewing angle, by variations in posture.
Bleeding and uneven backlighting in some monitors, causing brightness distortion,
especially toward the edges.
Smearing and ghosting artifacts caused by slow response times (>8 ms) and "sample and
hold" operation.
Only one native resolution. Displaying resolutions either requires a video scaler, lowering
perceptual quality, or display at 1:1 pixel mapping, in which images will be physically
too large or won't fill the whole screen.
Fixed bit depth, many cheaper LCDs are only able to display 262,000 colors. 8-bit S-IPSpanels can display 16 million colors and have significantly better black level, but are
expensive and have slower response time.
Low bit depth results in images with unnatural or excessive contrast.
Input lag
Dead or stuck pixels may occur during manufacturing or through use.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
30/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 30
In a constant-on situation, thermalization may occur, which is when only part of the
screen has overheated and looks discolored compared to the rest of the screen.
Not all LCDs are designed to allow easy replacement of the backlight.
Cannot be used with light guns/pens.
Loss of contrast in high temperature environments.
6.6 MAX 232
max 232 circuit diagram
Since the RS232 (Recommended Standard) is not compatible with todays microprocessor and
microcontrollers, we need a line driver to convert the RS232s signal to TTL voltage levels that
will be acceptable to the AT89C51 TXD and RXD pins.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
31/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 31
One example of such a converter is MAX 232. MAX 232 converts from Rs232 voltage levels to
TTL voltage levels, and vice versa. One advantages of the MAX232 chip is that it uses a +5v
power source which ,is the same as the source voltages for the 89C52.
In other words with a single +5v power supply we can power both the AT89C51 and MAX232,
with no need for the dual power supply that are common in many older systems. The MAX232
has 2 sets of line drivers for transferring and receiving data, as shown the line drivers used for
TXD are called T1 and T2, while the line drives for RXD are designated as R1 and R2.
The MAX232 is anintegrated circuit that converts signals from anRS-232 serial port to signals
suitable for use inTTL compatible digital logic circuits. The MAX232 is a dual driver/receiver
and typically converts the RX, TX, CTS and RTS signals.
The drivers provide RS-232 voltage level outputs (approx. 7.5 V) from a single + 5 V supply
via on-chipcharge pumps and external capacitors. This makes it useful for implementing RS-232
in devices that otherwise do not need any voltages outside the 0 V to + 5 V range, aspower
supply design does not need to be made more complicated just for driving the RS-232 in this
case.
The receivers reduce RS-232 inputs (which may be as high as 25 V), to standard
5 VTTL levels. These receivers have a typical threshold of 1.3 V, and a typicalhysteresis of
0.5 V.
The later MAX232A is backwards compatible with the original MAX232 but may operate at
higherbaud rates and can use smaller external capacitors 0.1Fin place of the 1.0 F
capacitors used with the original device. The newer MAX3232 is also backwards compatible, but
operates at a broader voltage range, from 3 to 5.5 V.
http://en.wikipedia.org/wiki/Integrated_circuithttp://en.wikipedia.org/wiki/RS-232http://en.wikipedia.org/wiki/Transistor-transistor_logichttp://en.wikipedia.org/wiki/Charge_pumphttp://en.wikipedia.org/wiki/Power_supplyhttp://en.wikipedia.org/wiki/Power_supplyhttp://en.wikipedia.org/wiki/Transistor-transistor_logichttp://en.wikipedia.org/wiki/Hysteresishttp://en.wikipedia.org/wiki/Baudhttp://en.wikipedia.org/wiki/Faradhttp://en.wikipedia.org/wiki/Faradhttp://en.wikipedia.org/wiki/Faradhttp://en.wikipedia.org/wiki/Faradhttp://en.wikipedia.org/wiki/Baudhttp://en.wikipedia.org/wiki/Hysteresishttp://en.wikipedia.org/wiki/Transistor-transistor_logichttp://en.wikipedia.org/wiki/Power_supplyhttp://en.wikipedia.org/wiki/Power_supplyhttp://en.wikipedia.org/wiki/Charge_pumphttp://en.wikipedia.org/wiki/Transistor-transistor_logichttp://en.wikipedia.org/wiki/RS-232http://en.wikipedia.org/wiki/Integrated_circuit5/28/2018 Transformer Fault Detection Using Zigbee and GSM
32/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 32
GSM
7.1 INTRODUCTION
GSM (Global System for Mobile Communications: originally from Groupe Special Mobile) is
the world's most popularstandard formobile telephony systems. TheGSM Association estimates
that 80% of the global mobile market uses the standard. GSM is used by over 1.5
billionpeople across more than 212 countries and territories. This ubiquity means that
subscribers can use their phones throughout the world, enabled by
internationalroaming arrangements between mobile network operators. GSM differs from its
predecessor technologies in that both signalling and speech channels aredigital,and thus GSM is
considered a second generation (2G)mobile phone system. This also facilitates the wide-spread
implementation of data communication applications into the system.
The GSM standard has been an advantage to both consumers, who may benefit from the ability
to roam and switch carriers without replacing phones, and also to network operators, who can
choose equipment from many GSM equipment vendors. GSM also pioneered low-cost
implementation of theshort message service (SMS), also called text messaging, which has since
been supported on other mobile phone standards as well. The standard includes a
worldwideemergency telephone number feature.
Newer versions of the standard were backward-compatible with the original GSM system. For
example,Release '97 of the standard added packet data capabilities by means ofGeneral Packet
Radio Service (GPRS). Release '99 introduced higher speed data transmission usingEnhanced
Data Rates for GSM Evolution (EDGE).
http://en.wikipedia.org/wiki/Comparison_of_mobile_phone_standardshttp://en.wikipedia.org/wiki/Mobile_telephonyhttp://en.wikipedia.org/wiki/GSM_Associationhttp://en.wikipedia.org/wiki/1000000000_(number)http://en.wikipedia.org/wiki/Roaminghttp://en.wikipedia.org/wiki/Mobile_network_operatorhttp://en.wikipedia.org/wiki/Digitalhttp://en.wikipedia.org/wiki/2Ghttp://en.wikipedia.org/wiki/Short_message_servicehttp://en.wikipedia.org/wiki/Emergency_telephone_numberhttp://en.wikipedia.org/wiki/3GPP#Standardshttp://en.wikipedia.org/wiki/General_Packet_Radio_Servicehttp://en.wikipedia.org/wiki/General_Packet_Radio_Servicehttp://en.wikipedia.org/wiki/Enhanced_Data_Rates_for_GSM_Evolutionhttp://en.wikipedia.org/wiki/Enhanced_Data_Rates_for_GSM_Evolutionhttp://en.wikipedia.org/wiki/Enhanced_Data_Rates_for_GSM_Evolutionhttp://en.wikipedia.org/wiki/Enhanced_Data_Rates_for_GSM_Evolutionhttp://en.wikipedia.org/wiki/General_Packet_Radio_Servicehttp://en.wikipedia.org/wiki/General_Packet_Radio_Servicehttp://en.wikipedia.org/wiki/3GPP#Standardshttp://en.wikipedia.org/wiki/Emergency_telephone_numberhttp://en.wikipedia.org/wiki/Short_message_servicehttp://en.wikipedia.org/wiki/2Ghttp://en.wikipedia.org/wiki/Digitalhttp://en.wikipedia.org/wiki/Mobile_network_operatorhttp://en.wikipedia.org/wiki/Roaminghttp://en.wikipedia.org/wiki/1000000000_(number)http://en.wikipedia.org/wiki/GSM_Associationhttp://en.wikipedia.org/wiki/Mobile_telephonyhttp://en.wikipedia.org/wiki/Comparison_of_mobile_phone_standards5/28/2018 Transformer Fault Detection Using Zigbee and GSM
33/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 33
7.2 THE CELLULAR NETWORK
GSM REFERENCE MODEL
MS
The MS consist of physical equipment used by the subscriber to access a PLMN for offered
telecommunication services. The MS includes a Mobile Terminal and depending on the services
it can support various Terminal Equipment(TE).Various type of MS, such as vehicle mounted
station, portable station, or handheld station, are used.
The MSs come in five power classes which define the maximum RF power level that the unit
can transmit. Basically, an MS can be divided into two parts. The first part contains the hardware
and software to support radio and human interface functions. The second part contains
terminal/user-specific data in the form of a smart card, which can effectively be considered a sort
of logical terminal. The SIM card plugs into the first part of the MS and remains in for the
duration of use. Without the SIM card, the MS is not associated with any user and cannot make
or receive calls (except possibly an emergency cal l if the network allows). The SIM card is
issued by the mobile service provider after subscription, while the first part of the MS would be
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
34/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 34
available at retail shops to buy orrent. This type of SIM card mobility is analogous to terminal
mobility, but provides a personal-mobility-like service within the GSM mobile network.
IMSI
The IMSI is assigned to an MS at subscription time. It uniquely identifies a given MS. The IMSI
will be transmitted over the radio interface only if necessary. The IMSI contains 15 digits and
includes
Mobile Country Code (MCC)3 digits (home country)
Mobile Network Code (MNC)2 digits (home GSM PLMN)
Mobile Subscriber Identification (MSIN)
National Mobile Subscriber Identity (NMSI)
TEMPORARY MOBILE SUBSCRIBER IDENTITY (TMSI )
The TMSI is assigned to an MS by the VLR. The MSI uniquely identifies an MS within the
area controlled by a given VLR. The maximum number of bits that can be used for the TMSI is
32
.
IMEI
The IMEI uniquely identifies the MS equipment. It is assigned by the equipment manufacturer.
The IMEI contains 15 digits and carries
The Type Approval Code (TAC)6 digits
The Final Assembly Code (FAC)2 digits
The serial number (SN)6 digits
A Spare (SP)1 digit
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
35/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 35
SIM
The SIM carries the following information
IMSI Authentication Key (Ki)
Subscriber information
Access control class
Cipher Key (Kc)
TMSI
Additional GSM services
Location Area Identity (LAI)
Forbidden PLMN
BSS
The BSS is the physical equipment that provides radio coverage to prescribed geographical
areas, known as the cells. It contains equipment required to communicate with the MS.
Functionally, a BSS consists of a control function carried out by the BSC and a transmitting
function performed by the BTS. The BTS is the radio transmission equipment and covers each
cell. A BSS can serve several cells because it can have multiple BTSs.The BTS contains the
Transcoder Rate Adapter Unit (TRAU). In TRAU, the GSM-specific speech encoding and
decoding is carried out, as well as the rate adaptation function for data. In certain situations the
TRAU is located at the MSC to gain an advantage of more compressed transmission between the
BTS and the MSC
NSS
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
36/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 36
The NSS includes the main switching functions of GSM, databases required for the subscribers,
and mobility management. Its main role is to manage the communi cat ions between GSM and
other network users.Within the NSS, the switching functions are performed by the MSC.
Subscriber information relevant to provisioning of services is kept in the HLR. The other
database in the NSS is the VLR. The MSC performs the necessary switching functions required
for the MSs located in an associated geographical area, called an MSC area. The MSC monitors
the mobility of its subscribers and manages necessary resources required to handle and update
the location registration procedures and to carry out the handover functions. The MSC is
involved in the interworking functions to communicate with other networks such as PSTN and
ISDN. The interworking functions of the MSC depend upon the type of the network to which it
is connected and the type of service to be performed. The call routing and control and echo
control functions are also performed by the MSC.
The HLR is the functional unit used for management of mobile subscribers. The number of
HLRs in a PLMN varies with the characteristics of the PLMN. Two types of information are
stored in the HLR: subscriber information and part of the mobile information to allow incoming
calls to be routed to the MSC for the particular MS. Any administrative action by the service
provider on subscriber data is performed in the HLR. The HLR stores IMSI, MS ISDN number,
VLR address, and subscriber data (e.g., supplementary services).
The VLR is linked to one or more MSCs. The VLR is the functional unit that dynamically stores
subscriber information when the subscriber is located in the area covered by the VLR. When a
roaming MS enters an MSC area, the MSC informs the associated VLR about the MS the
MS goes through a registration procedure. The registration procedure for the MSincludes these
activities:
The VLR recognizes that the MS is from another PLMN.
If roaming is allowed, the VLR finds the MSs HLR in its home PLMN.
The VLR constructs a Global Title (GT) from the IMSI to allow signaling from the VLR
to the MSs HLR via the PSTN/ISDN networks.
The VLR generates a Mobile Subscriber Roaming Number (MSRN) thatis used to route
incoming calls to the MS.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
37/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 37
The MSRN is sent to the MSs HLR.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
38/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 38
ZIGBEE
ZigBee is a low-cost, low-power, wireless mesh network standard. The low cost allows the
technology to be widely deployed in wireless control and monitoring applications. Low power-
usage allows longer life with smaller batteries. Mesh networking provides high reliability and
more extensive range. ZigBee chip vendors typically sell integrated radios and microcontrollers
with between 60 KB and 256 KB flash memory.
ZigBee operates in the industrial, scientific and medical (ISM) radio bands; 868 MHz in Europe,
915 MHz in the USA and Australia, and 2.4 GHz in most jurisdictions worldwide. Data
transmission rates vary from 20 to 900 kilobits/second.
The ZigBee network layer natively supports both star and tree typical networks, and generic
mesh networks. Every network must have one coordinator device, tasked with its creation, the
control of its parameters and basic maintenance.
TYPES OF ZIGBEE DEVICE
Zigbee devices are of three types:
ZigBee coordinator(ZC):The most capable device, the coordinator forms the root of thenetwork tree and might bridge to other networks. There is exactly one ZigBee coordinator in
each network since it is the device that started the network originally. It stores information
about the network, including acting as the Trust Center & repository for security keys.
ZigBee Router(ZR): As well as running an application function, a router can act as anintermediate router, passing on data from other devices.
ZigBee End Device (ZED):Contains just enough functionality to talk to the parent node
(either the coordinator or a router); it cannot relay data from other devices. This relationshipallows the node to be asleep a significant amount of the time thereby giving long battery life.
A ZED requires the least amount of memory, and therefore can be less expensive to
manufacture than a ZR or ZC.
USES OF ZIGBEE
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
39/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 39
ZigBee protocols are intended for embedded applications requiring low data rates and low power
consumption. The resulting network will use very small amounts of power individual devices
must have a battery life of at least two years to pass ZigBee certification.
Typical application areas include:
Home Entertainment and ControlHome automation, smart lighting, advanced
temperature control, safety and security, movies and music
Wireless Sensor Networks Starting with individual sensors like Telosb/Tmote and Iris
from Memsic
Industrial control
Embedded sensing
Medical data collection
Smoke and intruder warning
Building automation
8.2 PIEZO BUZZER
A buzzer or beeper is an audio signaling device, which may be mechanical, electromechanical,
or piezoelectric. Typical uses of buzzers and beepers include alarm devices, timers and
confirmation of user input such as a mouse click or keystroke.
The piezo buzzer produces sound based on reverse of the piezoelectric effect. The generation of
pressure variation or strain by the application of electric potential across a piezoelectric material
is the underlying principle. These buzzers can be used alert a user of an event corresponding to a
switching action, counter signal or sensor input. They are also used in alarm circuits.
The buzzer produces a same noisy sound irrespective of the voltage variation applied to it. It
consists of piezo crystals between two conductors. When a potential is applied across these
crystals, they push on one conductor and pull on the other. This, push and pull action, results in a
sound wave. Most buzzers produce sound in the range of 2 to 4 kHz.
The Red lead is connected to the Input and the Black lead is connected to Ground.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
40/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 40
CIRCUIT DIAGRAM OF BUZZER
This buzzer is an piezo type audio signaling device, which has a piezo element and a oscillating
circuit inside which oscillates the piezo brass base plate, which when given voltage difference
produces sound of a predefined frequency. You must be aware of such sounds of buzzer like
BEEP sound in many appliances.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
41/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 41
INTERFACING
INTERFACING 16x2 LCD WITH MICROCONTROLLER
A 16x2 LCD means it can display 16 characters per line and there are 2 such lines. In this LCD
each character is displayed in 5x7 pixel matrix. This LCD has two registers.
1. Command/Instruction Register- stores the command instructions given to the LCD. A
command is an instruction given to LCD to do a predefined task like initializing, clearing the
screen, setting the cursor position, controlling display etc.
2. Data Register- stores the data to be displayed on the LCD. The data is the ASCII value of the
character to be displayed on the LCD.
Commonly used LCD Command codes:
The pin description of this module is given below:
Hex
Code
Command to LCD Instruction Register
1 Clear screen display
2 Return home
4 Decrement cursor
6 Increment cursor
E Display ON, Cursor ON
80 Force the cursor to the beginning of the 1st
lineC0 Force cursor to the beginning of the 2ndline
38 Use 2 lines and 5x7 matrix
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
42/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 42
Pin configuration:
Pin Symbol Description
1 VSS Ground 0 V2 VCC Main power supply +5 V
3 VEE Power supply to control contrast Contrast adjustment by providing a
variable resistor through VCC
4 RS Register Select RS=0 to select Command Register
RS=1 to select Data Register
5 R/W Read/write R/W=0 to write to the register
R/W=1 to read from the register
6 EN Enable A high to low pulse (minimum
450ns wide) is given when data is
sent to data pins
7 DB0
To display letters or numbers, their
ASCII codes are sent to data pins
(with RS=1). Also instruction
command codes are sent to these
pins.
8 DB1
9 DB2
10 DB3 8-bit data pins
11 DB4
12 DB5
13 DB6
14 DB7
15 Led+ Backlight VCC +5 V
16 Led- Backlight Ground 0 V
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
43/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 43
INTERFACING GSM MODULE WITH MICROCONTROLLER
GSM is widely used mobile communication architecture used in most of the countries. This
project demonstrates theinterfacing of microcontrollerAT89S52 with HyperTerminal andGSM
module. It aims to familiarize with the syntax ofAT Commandsand their Information Response
and Result Codes. The ASCII values of characters in the Information Response, Result Codes
and their syntax can be monitored by an LED array. For the basic concepts, working and
operation of AT commands and GSM module referGSM/GPRS Module.
A GSM module has an RS232 interface for serial communication with an external peripheral. In
this case, the transmit pin (Tx) of the computersSerial port is connected with the receive pin
(Rx) of the GSM modules RS-232 interface. The transmit pin (Tx) of the RS-232 of GSM
module is connected to receive pin (Rx) of microcontrollers serial transmission pin. And the
serial transmit pin of the microcontroller is connected to the receive pin of the computersSerial
port.
http://www.engineersgarage.com/tutorials/at-commandshttp://www.engineersgarage.com/tutorials/at-commandshttp://www.engineersgarage.com/tutorials/at-commandshttp://www.engineersgarage.com/articles/gsm-gprs-moduleshttp://www.engineersgarage.com/articles/gsm-gprs-moduleshttp://www.engineersgarage.com/articles/gsm-gprs-moduleshttp://www.engineersgarage.com/tutorials/at-commands5/28/2018 Transformer Fault Detection Using Zigbee and GSM
44/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 44
SOFTWARE USED
INTRODUCTION TO EMBEDDED C:
Embedded is the extension of c language. Embedded C is a compiler which constitutes more
build in function. By using c language it is easy to connect the comport easily. The embedded c
compiler has the bias function to connect the comport. The command from fussing kit sends
from the c program according to user wish.
HI-TEC C
HI-TEC C is a set of software that translates the program written in the C language in to
executable machine code versions are available which compile the program for the operation
under the host operating system.
Some of the Hi-Tec features are
A simple batch file will compile, assemble and link entire program
The compiler perform strong type checking and issues warning about various constructs
which may represent programming errors
The generated code is extremely small and fast in execution
A full run time library is provided implementing all standard c input/ output and other
function
The source code for all run time routine is provided
A power full general purpose macro-assembler is provided
Programs may be generated to execute under the host operating system or customized
for installation in ROM.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
45/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 45
PROBLEMS RESOLVED BY THE SYSTEM:
Early detection of failures in electric power transformers can be succeeded with
neural modeling and the Local Statistical Approach to Fault Diagnosis
Neuro-fuzzy networks are proposed for modeling the dynamics of a critical parameter
of the power transformer known as Hot Spot Temperature.
The output of the neural-fuzzy network is compared to the output of the exact model
(Representing the fault-free condition of the transformer) and residuals are generated
The residuals undergo statistical signal processing according to a fault detection
and isolation algorithm (Local Statistical Approach to FDI)
The Local Statistical Approach consists of the global test for fault detection and
of the sensitivity and min-max tests for fault isolation If a fault threshold defined by the FDI algorithm is exceeded thendeviation from
normal operation can be detected at its early stages and an alarm can be launched
The proposed FDI approach can be applied to other components of the power grid,
e.g power generators, etc.
ADVANTAGES:
Detecting signs of failure conditions
Reducing probability of catastrophic failure
Reducing unscheduled outages
Addressing specific unit or population issues
Loading T&D equipment for maximum efficiency
Deferring upgrade capital costs
Managing & extending the life of equipment
Reducing Observation & Measurement costs.
5/28/2018 Transformer Fault Detection Using Zigbee and GSM
46/46
TRANSFORMER FAULT DETECTION USING ZIGBEE 2011-12
Department of ECE,DSCE Page 46
CONCLUSION
Transformers are static devices, totally enclosed and generally oil immersed. Therefore chances
of faults occurring on them are very rare. However the consequences of even a rare fault may bevery serious unless the transformer is quickly disconnected from the system. This necessitates to
provide adequate automatic protection for transformers against possible faults. The major faults
on transformers occur due to short circuits in the transformers or in their connections. The basic
system used for protection against these faults is the differential relay Protection of power
transformer is a big challenge nowadays. By the help of microcontroller-based relay, protection
of transformer is performed very quickly and accurately. This system provides a better and safer
protection than the other methods which are currently in use. The advantages of this system over
the current methods in use are fast response, better isolation and accurate detection of the fault.
This system overcomes the other drawbacks in the existing systems such as maintenance and
response time.