TRACTOR PERFORMANCE TEST - Francisco Josephinum · Tractor: CASE IH PUMA 175 CVT BLT reference number: 007-CIH/15 - OECD Code 2 Page 3/43 Foreword: CASE IH PUMA 175 CVT tractors and

TRACTOR PERFORMANCE TEST

BLT reference number: 007-CIH/15

Report on test in accordance with the OECD-standard Code 2 for the Official Testing of Agricultural Tractor Performance

Number and date of approval: 2/2 960 on 11 July 2016

Tractor CASE IH PUMA 175 CVT

Location of tractor assembly:

CNH Industrial N.V. Basildon Essex SS14 3AD United Kingdom

CNH Industrial Oesterreich GmbH Steyrerstrasse 32 AT 4300 St Valentin Austria

This report has been approved by the OECD Co-ordinating Centre (ENAMA, Italy) as being in accordance with the OECD Tractors Test Code

HBLFA Francisco Josephinum BLT Wieselburg AT 3250 Wieselburg, Rottenhauser Straße 1 [email protected], http://blt.josephinum.at

OE

CD

- T

ES

T R

EP

OR

T

Tractor: CASE IH PUMA 175 CVT BLT reference number: 007-CIH/15 - OECD Code 2

Page 2/43

TABLE OF CONTENTS

Page

1 SPECIFICATIONS OF TRACTOR ................................................................................................................ 3

1.1 Identification ........................................................................................................................................ 3 1.2 Engine ................................................................................................................................................. 4 1.3 Transmission ....................................................................................................................................... 7 1.4 Power take-off ..................................................................................................................................... 8 1.5 Hydraulic power lift ............................................................................................................................ 10 1.6 Three-point linkage ............................................................................................................................ 11 1.7 Swinging drawbar .............................................................................................................................. 13 1.8 Trailer hitch ........................................................................................................................................ 13 1.9 Holed drawbar ................................................................................................................................... 13 1.10 Steering ............................................................................................................................................. 13 1.11 Brakes ............................................................................................................................................... 13 1.12 Wheels .............................................................................................................................................. 14 1.13 Protective structure ........................................................................................................................... 15 1.14 Seat ................................................................................................................................................... 15 1.15 Lighting .............................................................................................................................................. 16

2 TEST CONDITIONS .................................................................................................................................... 17

2.1 Overall dimensions ............................................................................................................................ 17 2.2 Ground clearance .............................................................................................................................. 17 2.3 Tractor mass ..................................................................................................................................... 17 2.4 Ballast ................................................................................................................................................ 17 2.5 Track specifications ........................................................................................................................... 17 2.6 Tyres and track width specification ................................................................................................... 18 2.7 Fuel.................................................................................................................................................... 19 2.8 Oils and lubricants ............................................................................................................................. 19 2.9 Reagent ............................................................................................................................................. 20

3 TEST RESULTS .......................................................................................................................................... 21

3.1 Main power take-off ........................................................................................................................... 21 3.2 Hydraulic power and lifting force ....................................................................................................... 37 3.3 Compulsory drawbar power and fuel consumption test (unballasted tractor) ................................... 40

4 OPTIONAL TEST RESULTS ...................................................................................................................... 42

4.1 Engine test ........................................................................................................................................ 42 4.2 Optional test results........................................................................................................................... 42

5 REPAIRS AND ADJUSTMENTS ................................................................................................................ 42

6 REMARKS ................................................................................................................................................... 43


Page 3/43

Foreword: CASE IH PUMA 175 CVT tractors and NEW HOLLAND T7.225 AC tractors are technically identical in all main respects except with regard to the trade name and the colour. The effect of these modification on performance has been examined. Modifications are considered not to affect the results of the test. All tests were carried out on a tractor NEW HOLLAND T7.225 AC. The approval number of this NEW HOLLAND T7.225 AC tractor is 2/2 959 on 06th of July 2016.

C5 Tractor manufacturer’s name and address: CNH Industrial Europe Holding S.A. 24, Boulevard Royal L-2449 Luxembourg

D Location of tractor assembly: CNH Industrial N.V. Basildon Essex, SS14 3AD United Kingdom CNH Industrial Oesterreich GmbH Steyrerstrasse 32 AT 4300 St. Valentin Austria

D Submitted for test by: The manufacturer

C Selected for test by: The manufacturer in agreement with BLT

D Place of running-in: Basildon, Essex

D Duration of running-in: 73 hours

C Date of test: Wieselburg, April 2015 to May 2016

C Location of test: HBLFA Francisco Josephinum BLT Wieselburg Rottenhauser Straße 1 AT 3250 Wieselburg

C Code version: OECD Code 2 – July 2014

1 SPECIFICATIONS OF TRACTOR

1.1 Identification

1.1.1 Denomination

C Make of the tractor: CASE IH

C Model (trade name): PUMA 175 CVT

C Type: 4 WD

1.1.2 Numbers

D 1st Serial No. or prototype: ZFEN01001

C Serial No.: ZFEN01223

------------------------------------------------ 5 An item marked “C” indicates to the test report user that the information declared by the manufacturer has been checked; an item marked "D" that the manufacturer's declaration has been endorsed.


Page 4/43

1.1.3 Other specifications (if applicable)

D Model(s) for other countries: N/A

C Transmission type or gears x ranges: CVT – 2 Ranges

C Speed version: 50 km/h

D Manufacturer identification or tech. type number: EPRSBF

1.2 Engine

C Make: FPT Industrial

C Model: F4DFE613M*B

C Type: watercooled 4 stroke diesel engine, common rail injection, supercharged with intercooler and SCR system with DOC

C Serial number: 001325978

1.2.1 Cylinders

C Number / disposition: 6 / vertical in-line

D Bore / stroke: 104 mm / 132 mm

D Capacity: 6728 cm³

D Compression ratio: 18.0:1

D Arrangement of valves: overhead

D Cylinder liners: none, monobloc construction

1.2.2 Supercharging

C Make: Borg Warner

C Model: TS

C Type: exhaust gas driven

D Pressure: 0.2 MPa

1.2.3 Fuel system

C Fuel feed system: gear pump

C Make / Model / Type of fuel filter: N/A, 3 total, 2 disposable canister filters incorporating sediment and water separation plus metal tank strainer and inline filter

D Capacity of fuel tank: 264 + 64 dm3

Injection pump

C Make: Bosch

C Modell: CR-CP3

C Type: high pressure pump common rail

C Serial N°: PN: 5801633945

Manufacturer's production setting of injection pump

C Flow rate unboosted mode

(rated engine speed and full load): 31.8 ± 1.98 dm³/h

C Flow rate boosted mode

(rated engine speed and full load): 37.2 ± 1.98 dm³/h

D Timing: variable


Page 5/43

Injectors

D Make: Bosch

D Modell: N/A

D Type managed by electronic control unit

D Injection pressure: 90 MPa

C Make / Model / Type of carburetor: N/A

1.2.4 Governor

C Make: Bosch

C Model: EDC17CV41

C Type: electronic control

C Governed range of engine speed: from 650 100 to 2300 50 min-1

C Rated engine speed: 2200 min-1 / 2100 min-1 (Remark: explanation in paragraph 6 Remarks)

1.2.5 Air cleaner

Pre-cleaner

C Make: N/A

C Model: N/A

C Type: Spin tubes incorporated

C Location of air intake: air cleaner canister inlet

Main cleaner

C Make: Donaldson

C Model: 1.19.1 01AB

C Type: 3 stage dry paper element

C Location of air intake: under bonnet on front and above radiator

C Maintenance indicator: warning light on instrument panel

1.2.6 Lubrication system

D Type of feed pump: forced feed from concentric rotor

D Type of filter(s): metal mesh strainer in sump on suction line and full flow disposable canister on pressure line to engine

C Number of filter(s): 1

1.2.7 Cooling system

C Type of coolant: water and antifreeze (50 % solution)

D Type of pump: belt driven centrifugal impeller

Specification of fan or blower

C Number of fan blades: 9

C Fan diameter: 555 mm

D Coolant capacity: 25 dm3

C Type of temperature control: thermostat with full flow bypass

D Over-pressure system: 100 kPa


Page 6/43

1.2.8 Starting system

D Make: Iskra

D Model: AZF4115

C Type: solenoid engaged

D Starter motor power rating: 4.2 kW

D Cold starting aid: Phillips and Temro thermostarter (optional)

C Safety device: starting inoperable unless shuttle lever in neutral, clutch pedal depressed and seat presence switch is activated

1.2.9 Electrical system

C Voltage: 12 V

Generator

D Make: Iskra

D Model: AAN5164

C Type: belt driven

D Power: 1.44 kW or 1.8 kW

Battery of accumulators

C Number: 1

C Rating: 12 V, 176 Ah at 20 hours

1.2.10 Exhaust system

DOC

C Make / Modell / Type: Katcon / R 6.77-96.5-150-19-20

C Location: above engine rear (under hood)

SCR/DPF

C Make / Modell / Type: Cor-Tubi / 1-19-IWC-4-4-9.5-R

C Location: on right-hand side of engine rear

Vertical silencer

C Make / Modell / Type: TMM / none / vertical stack pipe with silencer

C Location: on right-hand side of engine rear, above SCR

1.2.11 Reagent Injection System

C Make / Model / Type: CNHi / see above / SCR using DEF

D Location: on right-hand side of engine rear

D Specifications of the reagent to be used: Aqueous Urea Solution 32 (AUS 32) according to ISO 22241-1

1.2.12 Diesel Particulate Filter

D Make / Model / Type: N/A


Page 7/43

1.3 Transmission

1.3.1 Clutch (travel alone)

D Make: CNHi

D Model: own model

D Type: multidisc wet plate clutch

D Number of plates: 9

D Diameter of plates: 160 mm

C Method of operation: electro-hydraulic

1.3.2 Gear box

D Make CNHi

D Model own model

C Type: CVT (mechanic/hydraulic) - SWB

C Description: automatically continuously variable transmission with compound planetary gears. Electro/ Hydraulic, 2 forward and 1 reverse gear ranges, selected by buttons and slide controls on an adjustable lever mounted on the right-hand console. Forward/reverse is actuated by a steering column mounted shuttle lever or 2 buttons on the adjustable lever mounted on the right-hand console.

Forward Reverse

C Number of ranges/groups 2 1

C Number of gears 1 1

C Total of arrangements 2 1

D Available options: 2 x 1 (35 km/h Japan)

2 x 1 (40 km/h Economy) 2 x 1 (50 km/h)

1.3.3 Rear axle and final drivers

D Make: CNHi

D Model: own model

C Type: crown wheel pinion with differential and inboard epicyclic reduction gear final drive

Differential lock

D Type: multiplate wet discs

C Method of engagement: electro-hydraulic actuation in response to signal from switch on right-hand control panel or auto diff lock actuation

C Method of disengagement: via panel switch or in response to signal from brakes on application, or auto diff lock disen-gagement


Page 8/43

1.3.4 Front axle and final drives

C Make: CNHi

D Model: own model

C Type: crown wheel and pinion with differential and outboard epicyclic reduction gear final drives

Differential lock

D Type: mechanical or multiplate clutch

C Method of engagement: electro-hydraulic actuation in response to signal from switch on right-hand control panel or auto diff lock actuation

C Method of disengagement: via panel switch or in response to signal from brakes on application, or auto diff lock disen-gagement

1.3.5 Total ratios and travelling speeds

Gear No

Group or range

Number of engine revolutions for one revolution of the

driving wheels

Nominal travelling speed (*) at rated engine speed of 2200 min-1

km/h

Forward

C F1 N/A 0 -> 13.00

C F2 N/A 13.00 -> 47.30 (**)

Reverse

C R1 N/A 0 -> 19.90

(*) Calculated with a tyre dynamic radius index of 875 mm – ETRTO standards manual 2016 (**) Electronically limited to 50 km/h in case of mounted tyres with dynamic radius index of 925 mm

C Number of revolutions of front-wheels for one revolution of rear-wheels: 1.322

1.4 Power take-off

1.4.1 Main power take-off

C Type: fully independent

C Method of engagement: electro - hydraulic operated multi-plate clutch in response to a signal from a knob on the right–hand control panel

C Number of shafts: 1 interchangeable shaft

Method of changing power take-off speeds

C A (as fitted on test tractor) two speed interchangeable 1000/540 – reversing shaft ends

C B three speed shiftable - 1000/540/540E, by switch on right-hand console

C C three speed shiftable - 1000/1000E/540E, by switch on right-hand console


Page 9/43

1.4.1.1 Power take-off proportional to engine speed

Power take-off at 540 min-1

C Location: rear of tractor

C Diameter of power take-off shaft end: 35 mm

C Number of splines: 6

C Conformity with ISO 500-1:2004/Cor 1:2005, ISO 500-2:2004, ISO 500-3:2004 yes

C Height above ground: 908,5 mm

C Distance from the median plane of the tractor: 0 mm

C Distance behind rear-wheel axis: 570 mm

C PTO speed at rated engine speed:

A 540 603 min-1

B 540 625 min-1

B, C 540E 754 min-1

C Engine speed at standard power take-off speed:

A 540 1969 min-1

B 540 1901 min-1

B, C 540E 1575 min-1

C Ratio of rotation speeds (engine speed/PTO speed)

A 540 3,647

B 540 3,520

B, C 540E 2,917

D Power restriction: none

D Maximum torque transmissible: maximum available

C Direction of rotation (viewed from behind tractor): clockwise

Power take-off at 1000 min-1 (rev/min)

C Location: rear of tractor

C Diameter of power take-off shaft end: 35 mm

C Number of splines: 21

C Conformity with ISO 500-1:2004/Cor 1:2005, ISO 500-2:2004, ISO 500-3:2004 yes

C Height above ground: 908,5 mm

C Distance from the median plane of the tractor: 0 mm

C Distance behind rear-wheel axis: 570 mm

C PTO speed at rated engine speed:

A, B, C 1000 1141 min-1

C 1000E 1380 min-1

C Engine speed at standard power take-off speed:

A, B, C 1000 1929 min-1

C 1000E 1594 min-1

C Ratio of rotation speeds (engine speed/PTO speed)

A, B, C 1000 1,929

C 1000E 1,594


Page 10/43

D Power restriction: none

D Maximum torque transmissible: maximum available

C Direction of rotation (viewed from behind tractor): clockwise

1.4.1.2 Power take-off proportional to ground speed

C Indicate 540 or 1000 min-1(rev/min): N/A

C Travelling distance for one revolution of take-off shaft N/A

C Number of power take-off shaft revolutions for one revolution of (rear) driving wheels: N/A

C Direction of rotation with forward gear engaged (viewed from behind tractor): N/A

1.4.2 Optional power take-off

C Give the same description as for the main PTO. none

1.5 Hydraulic power lift

C Make: CNHi

D Model: own model

C Type: lower link sensing, electronically controlled

C Type of hydraulic system: closed center, load sensing

C Type and number of cylinders: 2 external single acting cylinders 100 mm diameter of cylinder

C Type of linkage lock for transport: hydraulic

D Relief valve pressure setting (tolerance): 21.0 +/- 0.5 MPa

D Opening pressure of cylinder safety valve: 22.0 – 23.0 MPa

D Lift pump type: variable displacement pump

D Transmission between pump and engine: gear driven by transmission

C Type and number of filters: 1 disposable canister and 1 element filter

C Site of oil reservoir: transmission housing

C Type, number and location of tapping points: ISO standard breakaway couplers, 3 standard, 4 or 5 optional (4 test tractor), rear of the tractor optional power-beyond (rear) optional up to 3 mid mount valves

D Maximum volume of oil available to external cylinders: 38 dm³ under normal conditions

40 dm3 when operating stationary


Page 11/43

1.6 Three-point linkage

Figure 1.1: Lift test – linkage geometry

Figure 1.2: Lift test – linkage geometry


Page 12/43

C Category: 2 in conformity with ISO 730:2009

D Category adapter: optional category 3 adaptors available

Figures 1.1 and

1.2

Dimensions or range

Settings used in

test

mm mm

C Length of lift arms: (A) 310 310

C Length of lower links: (B) 974 974

Distance of lift arm pivot point from rear-wheel axis:

C horizontally: (a) 160 160

C vertically: (b) 364 364

C Horizontal distance between the 2 lower link points: (u) 560 560

C Horizontal distance between the 2 lift arm end points: (v) 549 549

C Length of upper link (S) 647 to 930 790

Distance of upper link pivot point from rear-wheel axis:

C horizontally: (c) 410 to 445 410

C vertically: (d) 263.5 to 208.5 263.5

Distance of lower link pivot point from rear-wheel axis

C horizontally: (e) 220 220

C vertically: (f) 250 250

C Distance of lower link pivot points to lift rod pivot points on lower links:

(D)

440 to 505

505

C Length of lift rods: (L) 710 to 865 865

Height of lower hitch points relative to the rear-wheel axis

C in low position (h) 760 to 260 695

C in high position (H) 40 to 322 40

C Height above ground of lower hitch points when locked in transport position (*)

any height

within lift range

(*) Assuming r = 925 tyre dynamic radius index of ISO 4252-1:2005 (pneumatic tyred tractors only)

Table 1.1: Dimensions of linkage geometry when connected to the standard


Page 13/43

1.7 Swinging drawbar

C Type: clevis

Height above ground

C Maximum: 612 mm

C Minimum: 612 mm

C Type of adjustment: longitudinal, by 3 different holes

C Distance of hitch point from rear-wheel axis horizontally: 820-920-970 mm

Distance of hitch point from power take-off shaft end

C Vertically: 296.5 mm

C Horizontally: 250-350-400 mm

Lateral adjustment (centre of clevis)

C Right hand: 15°

C Left hand: 15°

C Distance of pivot point from rear-wheel axis horizontally: N/A

C Diameter of drawbar pinhole: 33 mm

Maximum vertical permissible load:

D Clevis uppermost: 26.25-17.10-14.70 kN

D Clevis underneath: N/A

1.8 Trailer hitch

Not fitted to the tested tractor

1.9 Holed drawbar

Not fitted to the tested tractor

1.10 Steering

D Make: CNHi

D Model: own model

D Type: hydrostatic kingpin steering of front wheels

Method of operation

D Pump: Bosch Rexroth

C Ram(s): 2, balanced system with double acting cylinders one operating each steering arm

D Working pressure: 17.0 ± 0.5 (or 19.0 ± 0.5) MPa

1.11 Brakes

1.11.1 Service brake

D Make: CNHi

D Model: own model

D Type: oil immersed two plate disc

C Method of operation: hydrostatic, independent on rear wheels; when the service brake is activated the front wheel drive is automatically engaged providing 4-wheel braking

D Trailer braking take-off (hydraulic or air brake): not fitted on test tractor


Page 14/43

1.11.2 Parking brake

D Type: fully independent six plate disc operating on bevel pinion shaft

C Method of operation: hand lever with ratchet

1.12 Wheels

Number

C Front: 2 driving and steering

C Rear: 2 driving

C Wheelbase: 2789 mm (suspended front axle)

Track width adjustment:

Minimum mm

Maximum mm

Adjustment method

D Front 1540 2260 reversing wheels and offset lug rims

D Rear 1550 2230 reversing wheels and offset lug rims, optional bar axle


Page 15/43

1.13 Protective structure

C Make: CNHi

C Model: SLTV 21

C Type: isomounted safety cab

C Manufacturer’s name and address: CNH Industrial Europe Holding S.A.

24, Boulevard Royal

L-2449 Luxembourg

Protective device

C Cab/frame/rollguard/other: safety cab

C Tiltable/not tiltable: not tiltable

OECD approval

C Approval number: 4/1 214/2

C Date of approval: 13 May 2015

C Nos. of minor modification certificates, if any: none

C Make: CNHi

C Model: SLTV 22

C Type: suspended safety cab

C Manufacturer’s name and address: CNH Industrial Europe Holding S.A.

24, Boulevard Royal

L-2449 Luxembourg

Protective device

C Cab/frame/rollguard/other: safety cab

C Tiltable/not tiltable: not tiltable

OECD approval

C Approval number: 4/1 213/2

C Date of approval: 13 May 2015

C Nos. of minor modification certificates, if any: none

Suspended cab (SLTV 22) fitted on test tractor.

1.14 Seat

1.14.1 Driver’s seat

C Make / Model / Type: Grammer / MSG95G/741 / air suspended seat

C Seat and steering wheel reversible: no

C Type of suspension: air spring

C Type of damping: hydraulic

Range of adjustment

C Longitudinally: 190 mm

C Vertically: 120 mm

C Safety belt: yes

Type: 2 point, spring retractable


Page 16/43

1.14.2 Optional driver’s seat(s)

D Make / Model / Type: Grammer / MSG95GL/741 / air suspended seat

D Type of suspension: air spring

D Type of damping: hydraulic

Range of adjustment

D Longitudinally: 190 mm

D Vertically: 120 mm

C Safety belt: yes


C Make / Model / Type: Grammer / MSG95AL/741 / air suspended seat, automatic



Range of adjustment



C Safety belt: yes


C Make / Model / Type: Grammer / MSG97EAC/741 / air suspended seat, automatic



Range of adjustment



C Safety belt: yes


Grammer MSG95G/741 fitted on test tractor.

1.14.3 Passenger seat:

C Location: none

C Capacity: none

1.15 Lighting

Height above

ground of centre Size

Distance from outside edge of lights to median

plane of tractor

mm mm mm

C Headlights 1482 140 x 110 190

D Sidelights 1915 80 x 90 900

C Rearlights 2083 265 x 55 885

C Rear fender reflectors Reflector stripes

2083 1910

265 x 55 365 x 32

885 925

D Axle reflectors 925 105 x 45 560

Remark: Sidelights and Axle reflectors not fitted on test tractor


Page 17/43

2 TEST CONDITIONS

2.1 Overall dimensions

Length

Width Height at top of

minimum maximum protective structure

exhaust pipe

mm mm mm mm mm

Ballasted NA NA NA NA NA

Unballasted 4734 2489 3000 3135 3166

2.2 Ground clearance

Unballasted tractor: 475 mm

Clearance-limiting part: APUH carrier

2.3 Tractor mass

Mass with cab

Ballasted Unballasted

Without driver With driver Without driver With driver

kg kg kg kg

Front N/A N/A 2845 2850

Rear N/A N/A 4260 4330

Total N/A N/A 7105 7180

2.4 Ballast

Not applicable

2.5 Track specifications

Not applicable


Page 18/43

2.6 Tyres and track width specification

2.6.1 Tyres and track for Hydraulic power and lifting force tests plus Specifications of tractor

Front Rear

Tyres

dimensions 600/65 R 28 710/70 R 38

ply rating 147 A8 166 A8

type radial radial

maximum load (tyre manufacturer’s) 30.75 kN 53.00 kN

maximum load (tractor manufacturer’s) 30.75 kN 53.00 kN

inflation pressure (tyre manufacturer’s) 160 kPa 160 kPa

dynamic radius index 700 mm 925 mm

Chosen track width 2030 mm 2030 mm

2.6.2 Tyres and track for Drawbar power and fuel consumption tests plus paragraph 1.3.5

Front Rear

Tyres

dimensions 420/85 R 28 520/85 R 38

ply rating 139 D 155 D

type radial radial

maximum load (tyre manufacturer’s) 30.99 kN 49.44 kN

maximum load (tractor manufacturer’s) 30.99 kN 49.44 kN

inflation pressure (tyre manufacturer’s) 160 kPa 160 kPa

dynamic radius index 675 mm 875 mm

Chosen track width 1830 mm 1830 mm


Page 19/43

2.7 Fuel

Type: Diesel oil to Class D, 1.5 to 5.5 cSt in conformity with national standard and directive 2002/80/EC

Density at 15 °C: 0.833 g/cm3

2.8 Oils and lubricants

2.8.1 Capacity and change interval

Capacity Oil change Filter change

dm3 h h

Engine 19 600 600

Gear box 100 1200 600

Front axle 14 1200 N/A

Final drive (front) 2.15 1200 N/A

Rear axle in common with gear box

Final drive (rear) in common with gear box

Hydraulic system (*) in common with gear box

Steering in common with gear box

Brakes 0.5 top-up N/A

(*) State if common with gear box and rear axle.

2.8.2 Specifications (SAE, API, CCMC, ACEA, Mil.L, ISO)

Recommended Used during test

Engine oil

Type: SAE 10W/30 as recommended

Viscosity: 11.5 cSt at 100 °C

Classification: API CG – 4

Transmission oils

Type: SAE 10W/30 as recommended

Viscosity: 9 cSt at 100 °C

Classification: API GL – 4

Hydraulic fluid

Type: same as transmission oil as recommended

Viscosity:

Classification:

Steering oil

Type: same as transmission oil as recommended

Viscosity:

Classification:

Hydraulic brakes fluid

Type: NH 610A as recommended

Viscosity: 6 cSt at 100 °C

Classification: no equivalent


Page 20/43

2.8.3 Grease

Number of lubrication points: 14

2.9 Reagent

Type: Aqueous Urea Solution 32 (AUS 32) according to ISO 22241-1

In conformity/not in conformity with national standard: yes

If the reagent is made of urea, Percentage of urea to water: 32,5 %


Page 21/43

3 TEST RESULTS

3.1 Main power take-off

Date of tests: 29 June 2015

Location of tests: BLT Wieselburg, HBLFA Francisco Josephinum, Austria

Type of dynamometer bench: Eddy Current, SCHENCK W780

UNBOOSTED POWER, rated engine speed 2200 min-1

Power Speed Fuel consumption Specific energy

Reagent consumption

Engine P. T.O. Fan Hourly Specific Hourly Specific

kW min-1 (rev/min) kg/h l/h g/kWh kWh/l kg/h l/h g/kWh

3.1.1 MAXIMUM POWER - ONE-HOUR TEST

127.5 1799 932 1860 28.83 35.05 226 3.64 2.91 2.69 22.8

3.1.2 POWER AT RATED ENGINE SPEED

109.2 2200 1140 1620 27.81 33.70 255 3.24 2.67 2.48 24.5

3.1.3 POWER AT STANDARD PTO SPEED [1000 ± 25 or 540 ± 10 min-1 (rev/min)]

125.0 1930 1000 1860 29.18 35.36 233 3.55 2.94 2.73 23.5

3.1.4 PART LOADS

3.1.4.1 the torque corresponding to maximum power at rated engine speed

109.2 2200 1140 1620 27.81 33.70 255 3.24 2.67 2.48 24.5

3.1.4.2 85% of torque obtained in 3.1.4.1

94.4 2237 1159 1920 24.90 30.20 264 3.12 2.56 2.38 27.2

3.1.4.3 75% of torque defined in 3.1.4.2

71.3 2252 1167 1740 21.20 25.68 297 2.77 1.93 1.79 27.1

3.1.4.4 50 % of torque defined in 3.1.4.2

47.9 2270 1176 1380 16.16 19.58 338 2.45 1.55 1.44 32.3


24.1 2287 1185 1440 12.02 14.58 498 1.66 1.08 1.01 44.9

3.1.4.6 unloaded

- 2306 1195 1500 8.56 10.38 - - 0.53 0.49 -

3.1.5 PART LOADS AT STANDARD POWER TAKE-OFF SPEED [ 1000 ± 25 or 540 ± 10 min-1 (rev/min)]

3.1.5.1 the torque corresponding to maximum power

125.0 1930 1000 1860 29.18 35.36 233 3.55 2.94 2.73 23.5

3.1.5.2 85 % of torque obtained in 3.1.5.1

108.5 1971 1021 1620 25.84 31.34 238 3.46 2.66 2.47 24.5


82.4 1996 1034 1620 20.77 25.19 252 3.27 2.12 1.97 25.7


55.5 2017 1045 1560 15.90 19.28 286 2.88 1.36 1.26 24.5


28.1 2040 1057 1620 11.42 13.85 407 2.03 0.86 0.80 30.6

3.1.5.6 unloaded

- 2055 1065 1620 6.88 8.35 - - 0.39 0.36 -


Page 22/43


Reagent consumption



3.1.6 PART LOADS AT DIFFERENT ENGINE SPEEDS

3.1.6.1 maximum power at rated engine speed

109.2 2200 1140 1620 27.81 33.70 255 3.24 2.67 2.48 24.5

3.1.6.2 80 % of power obtained in 3.1.6.1 at max. speed setting

87.4 2243 1162 1500 24.71 29.96 283 2.92 2.37 2.19 27.1

3.1.6.3 80 % of power obtained in 3.1.6.1 with governor control set to 90 % of rated engine speed

87.4 1980 1026 1560 22.12 26.85 253 3.25 2.26 2.10 25.9


43.7 1980 1026 1560 13.58 16.48 311 2.65 1.15 1.06 26.2


65.5 1320 684 1440 15.47 18.78 236 3.49 1.48 1.38 22.6


43.7 1320 684 1260 11.26 13.67 258 3.20 1.00 0.93 22.9

No load maximum engine speed: 2306 min-1 (rev/min)

Torque (equivalent crankshaft) at maximum power

At rated engine speed: 474.0 Nm

At 1-hour test: 676.9 Nm

Maximum torque (equivalent crankshaft): 742.2 Nm

At engine speed: 1500 min-1 (rev/min)

Mean atmospheric conditions:

Temperature 28 °C

Pressure 100.0 kPa

Relative humidity 60 %

Maximum temperatures:

Coolant 94 °C

Engine oil 120 °C

Fuel 55 °C

Engine air intake 30 °C


Page 23/43

Optional power take-off test BOOSTED POWER, rated engine speed 2200 min-1


Reagent consumption



3.1.1 MAXIMUM POWER - ONE-HOUR TEST (*)

- - - - - - - - - - -


125.2 2200 1140 1920 31.14 37.76 249 3.31 3.02 2.81 24.2


142.0 1930 1000 1980 32.63 39.61 230 3.59 3.10 2.88 21.9

3.1.4 PART LOADS


125.2 2200 1140 1920 31.14 37.76 249 3.31 3.02 2.81 24.2


107.7 2227 1154 1980 27.91 33.85 259 3.18 2.62 2.44 24.4


81.5 2248 1165 1620 22.30 27.04 273 3.02 2.08 1.94 25.5


54.8 2268 1175 1680 17.46 21.18 319 2.59 1.58 1.47 28.8


27.6 2287 1185 1800 12.93 15.69 468 1.76 1.07 1.00 38.8

3.1.4.6 unloaded

- 2310 1197 1680 8.74 10.61 - - 0.50 0.46 -



142.0 1930 1000 1980 32.63 39.61 230 3.59 3.10 2.88 21.9


122.8 1963 1017 1860 29.29 35.58 239 3.45 2.85 2.65 23.2


93.2 1988 1030 1980 22.84 27.74 245 3.36 2.26 2.11 24.3


63.0 2015 1044 1560 17.36 21.09 276 2.99 1.53 1.42 24.3


32.0 2044 1059 1560 12.64 15.36 396 2.08 1.04 0.97 32.7

3.1.5.6 unloaded

- 2065 1070 1620 7.21 8.75 - - 0.75 0.70 -

(*) One-hour test is not available in boosted mode


Page 24/43


Reagent consumption





125.2 2200 1140 1920 31.14 37.76 249 3.31 3.02 2.81 24.2


100.1 2231 1156 1680 27.04 32.82 270 3.05 2.57 2.39 24.7


100.1 1980 1026 1740 23.74 28.81 237 3.48 2.43 2.26 24.2


50.1 1980 1026 1620 14.91 18.08 298 2.77 1.15 1.07 23.0


75.1 1320 684 1440 17.13 20.79 228 3.61 1.65 1.54 22.0


50.1 1320 684 1440 12.37 15.01 247 3.34 1.07 1.05 21.3




At 1-hour test: N/A Nm




Temperature 30 °C

Pressure 100.0 kPa



Coolant 92 °C

Engine oil 121 °C

Fuel 56 °C


3.1.7 OPTIONAL: Additional power take-off ratio Not applicable


Page 25/43

3.1.8 Curves as a function of engine speed


Page 26/43


Page 27/43


Page 28/43

3.1.9 Curves of specific consumption as a function of PTO power


Page 29/43

Optional power take-off test

UNBOOSTED POWER, rated engine speed 2100 min-1


Reagent consumption



3.1.10 MAXIMUM POWER - ONE-HOUR TEST

127.5 1799 932 1860 28.83 35.05 226 3.64 2.91 2.69 22.8


118.5 2100 1088 1620 28.98 35.11 245 3.37 2.80 2.61 23.6


125.0 1930 1000 1860 29.18 35.36 233 3.55 2.94 2.73 23.5

3.1.13 PART LOADS


118.5 2100 1088 1620 28.98 35.11 245 3.37 2.80 2.61 23.6


102.1 2129 1103 1680 26.66 32.32 261 3.16 2.59 2.41 25.4


77.4 2152 1115 1800 20.60 24.99 266 3.10 2.03 1.88 26.2


52.1 2171 1125 1680 16.34 19.82 314 2.63 1.46 1.36 28.1


26.3 2191 1135 1680 12.03 14.59 458 1.80 0.99 0.92 37.8

3.1.13.6 unloaded

- 2214 1147 1620 7.73 9.37 - - 0.51 0.47 -



125.0 1930 1000 1860 29.18 35.36 233 3.55 2.94 2.73 23.5


108.5 1971 1021 1620 25.84 31.34 238 3.46 2.66 2.47 24.5


82.4 1996 1034 1620 20.77 25.19 252 3.27 2.12 1.97 25.7


55.5 2017 1045 1560 15.90 19.28 286 2.88 1.36 1.26 24.5


28.1 2040 1057 1620 11.42 13.85 407 2.03 0.86 0.80 30.6

3.1.14.6 unloaded

- 2055 1065 1620 6.88 8.35 - - 0.39 0.36 -


Page 30/43


Reagent consumption





118.5 2100 1088 1620 28.98 35.11 245 3.37 2.80 2.61 23.6


94.8 2142 1110 1500 24.78 30.07 261 3.15 2.46 2.29 26.0


94.8 1890 979 1500 21.77 26.43 230 3.59 2.33 2.16 24.5


47.4 1890 979 1560 14.05 17.05 296 2.78 1.50 1.39 31.7


71.1 1260 653 1380 16.08 19.52 226 3.64 1.68 1.56 23.6


47.4 1260 653 1200 11.76 14.27 248 3.32 1.11 1.03 23.3




At 1-hour test: 676.9 Nm




Temperature 28 °C

Pressure 100.0 kPa



Coolant 91 °C

Engine oil 120 °C

Fuel 54 °C



Page 31/43

Optional power take-off test BOOSTED POWER, rated engine speed 2100 min-1


Reagent consumption



3.1.16 MAXIMUM POWER - ONE-HOUR TEST (*)

- - - - - - - - - - -


135.1 2100 1088 1980 32.91 39.94 244 3.38 3.14 2.91 23.2


142.0 1930 1000 1980 32.63 39.61 230 3.59 3.10 2.88 21.9

3.1.19 PART LOADS


135.1 2100 1088 1980 32.91 39.94 244 3.38 3.14 2.91 23.2


116.2 2125 1101 1620 28.80 34.95 248 3.33 2.73 2.53 23.4


88.0 2144 1111 1860 22.94 27.85 261 3.16 2.17 2.02 24.6


59.4 2171 1125 1680 17.62 21.39 297 2.78 1.49 1.39 25.1


30.0 2191 1135 1740 12.65 15.36 422 1.95 1.03 0.95 34.3

3.1.19.6 unloaded

- 2208 1144 1680 7.81 9.48 - - 0.50 0.47 -



142.0 1930 1000 1980 32.63 39.61 230 3.59 3.10 2.88 21.9


122.8 1963 1017 1860 29.29 35.58 239 3.45 2.85 2.65 23.2


93.2 1988 1030 1980 22.84 27.74 245 3.36 2.26 2.11 24.3


63.0 2015 1044 1560 17.36 21.09 276 2.99 1.53 1.42 24.3


32.0 2044 1059 1560 12.64 15.36 396 2.08 1.04 0.97 32.7

3.1.20.6 unloaded

- 2065 1070 1620 7.21 8.75 - - 0.75 0.70 -

(*) One-hour test is not available in boosted mode


Page 32/43


Reagent consumption





135.1 2100 1088 1980 32.91 39.94 244 3.38 3.14 2.91 23.2


108.1 2131 1104 1920 26.64 32.33 246 3.34 2.64 2.45 24.4


108.1 1890 979 1800 24.67 29.94 228 3.61 2.52 2.35 23.3


54.1 1890 979 1680 15.14 18.38 280 2.94 1.38 1.28 25.5


81.1 1260 653 1380 18.24 22.15 225 3.66 1.89 1.75 23.3


54.1 1260 653 1380 12.81 15.56 237 3.47 1.13 1.05 20.9




At 1-hour test: N/A Nm




Temperature 30 °C

Pressure 100.0 kPa



Coolant 92 °C

Engine oil 121 °C

Fuel 56 °C



Page 33/43

3.1.22 Curves as a function of engine speed, rated engine speed 2100 min-1


Page 34/43


Page 35/43


Page 36/43

3.1.23 Curves of specific consumption as a function of PTO power, rated engine speed 2100 min-1


Page 37/43

3.2 Hydraulic power and lifting force

Date of tests: 24 April 2015 and 26 June 2015

3.2.1 Hydraulic power test

3.2.1.1 Hydraulic fluid data

Hydraulic fluid type: SAE 10W/30

Viscosity index (ISO 3448:1992): 9 cSt. at 100 °C

Viscosity at 65 C: 36.5 mm2/s

3.2.1.2 Compulsory Reporting (Test Results):

Pressure

Reservoir oil

Temperature C

(65 C target)

Engine speed

Flow rate

Power

MPa Min. Max. min-1 l/min kW

Rated Engine Speed

(Manufacturers Specification) 2200

3.2.1.2.1

Maximum (sustained) pressure with relief valve open as measured at the coupler

Pump stalled: No

20.1 60 69 2205

3.2.1.2.2

Flow rate corresponding to a hydraulic pressure equivalent to 90 % of the actual relief valve pressure setting and corresponding hydraulic power measured at one coupler

18.0 69 2215 78.8 23.6

3.2.1.2.3

Maximum available hydraulic power and corresponding flow and available coupler outlet pressure with flow through a single coupler pair

17.0 69 2210 93.5 26.5

3.2.1.2.4

Maximum available hydraulic power and corresponding flow and available coupler outlet pressure with flow through coupler pairs operating simultaneously

17.0 70 2200 113.2 32.1

3.2.1.3 OPTIONAL Test Results, Supplementary Reporting:

Not applicable


Page 38/43

3.2.1.4 Curves as a function of hydraulic pressure


Page 39/43

3.2.2 Compulsory Power lift test

Linkage settings for test - see paragraph 1.6

at the hitch point on the frame

Height of lower hitch points above ground in down position 230 mm 230 mm

Vertical movement

without lifting force 735 mm 795 mm

with lifting force 695 mm 725 mm

Maximum corrected force exerted through full range 43.3 kN 36.4 kN

Corresponding pressure of hydraulic fluid 18.5 MPa 18.5 MPa

Moment about rear-wheel axis 51.7 kNm 65.7 kNm

Maximum tilt angle of mast from vertical - ° *6 °

*Remark: Maximum tilt angle of mast from vertical at upper link pivot point setting for maximum lift capacity

Lifting heights relative to the horizontal plane including the lower link pivot points

mm -405 -365 -310 -210 -110 0 +140 +240 +290 +320

Lifting forces (the values of force measured shall be corrected to correspond to a hydraulic pressure equivalent to 90 % of the actual relief valve pressure setting of the hydraulic lift system):

at the hitch points in kN: 60.8 61.4 62.2 64.0 65.5 66.5 67.1 66.8 43.3 -

Corresponding pressure: 18.5 MPa

at the frame in kN: 59.0 58.9 59.0 59.0 59.0 58.7 58.15 56.6 55.6 36.4

Corresponding pressure: 18.5 MPa


Page 40/43

3.3 Compulsory drawbar power and fuel consumption test (unballasted tractor)

Date of tests: 21 and 25 April 2016

Type of track: Concrete

Height of drawbar

above ground

Tyre inflation pressure

Front Rear

mm] [kPa] [kPa]

unballasted 4WD 500 110 110

Gear

Num

ber

and r

ange

Pow

er

Dra

wbar

pull

Spe

ed

Eng

ine s

pee

d

Fan s

pee

d

Slip

of w

hee

ls

and/o

r tr

acks

Specific

fu

el

consum

ptio

n

Specific

energ

y

Specific

rea

gen

t

consum

ptio

n

Temperature Atmospheric conditions

Fuel

Coola

nt

Eng

ine o

il

Tem

pera

ture

Rela

tive

hum

idity

Pre

ssure

kW kN km/h min-1 min-1 % g/kWh kWh/l g/ kWh

°C °C °C °C % kPa

3.3.1 MAXIMUM POWER IN TESTED GEARS/SPEED SETTINGS

2.5 35.40 57.96 2.20 2260 1380 15.0 545.4 1.53 N/A 44 79 102 10 37 96.6

3.0 45.38 60.58 2.70 2250 1860 15.1 476.5 1.75 N/A 44 79 104 12 44 96.6

3.5 54.26 61.28 3.19 2250 2040 14.9 432.3 1.93 N/A 46 80 102 11 38 96.6

4.0 62.46 62.80 3.58 2240 1920 15.0 385.3 2.16 N/A 45 80 105 11 34 96.6

4.5 70.07 62.18 4.06 2230 1920 14.9 371.9 2.24 N/A 47 79 106 11 36 96.6

5.0 76.18 61.72 4.44 2170 1980 14.9 347.9 2.39 N/A 47 79 106 14 34 96.6

5.5 78.50 61.87 4.57 2030 1980 15.1 343.3 2.43 N/A 48 78 107 13 34 96.6

6.0 80.62 62.48 4.65 1930 1920 15.0 335.5 2.48 N/A 49 79 107 14 34 96.6

6.5 84.80 62.37 4.89 1840 1740 15.1 303.4 2.74 N/A 49 79 106 13 35 96.6

7.0 88.53 59.60 5.35 1800 1740 11.4 296.3 2.81 N/A 53 81 107 15 32 96.6

7.5 89.57 55.35 5.83 1800 1260 10.1 299.0 2.78 N/A 52 89 111 16 27 96.6

8.0 91.81 52.41 6.31 1800 1620 8.7 293.6 2.84 N/A 55 88 113 17 25 96.6

8.5 92.74 49.83 6.70 1800 1740 8.2 289.3 2.88 N/A 53 82 109 19 28 96.6

9.0 94.20 47.07 7.21 1800 1500 7.5 287.8 2.89 N/A 51 85 105 18 22 96.6

9.5 94.16 44.15 7.68 1800 1680 7.1 286.5 2.91 N/A 55 83 110 20 27 96.6

10.0 94.09 42.99 7.88 1800 1440 6.4 277.1 3.00 N/A 56 87 109 20 22 96.6

10.6 94.63 40.60 8.39 1800 1800 6.1 276.4 3.01 N/A 57 82 110 21 21 96.6

11.0 91.13 37.36 8.78 1800 1140 5.1 290.9 2.86 N/A 43 85 108 9 41 98.8

12.0 93.18 34.83 9.63 1800 1140 5.1 284.7 2.93 N/A 41 87 109 10 43 98.8

13.0 96.55 33.15 10.49 1800 1380 4.8 276.6 3.01 N/A 43 85 110 9 43 98.8

14.0* 88.83 28.15 11.40 1800 2040 4.4 389.5 2.14 N/A 40 77 104 7 50 98.8

15.0* 90.57 26.79 12.17 1800 1260 3.8 378.6 2.20 N/A 40 76 104 8 49 98.8

16.0* 95.55 26.67 12.90 1800 1500 3.5 364.2 2.29 N/A 41 77 103 10 42 98.8

17.0* 97.82 25.52 13.80 1800 1560 4.0 334.1 2.49 N/A 41 76 102 8 37 98.8

Remark:* indicates the operation status BOOSTED MODE (engine power management system activated)

Remark: test up to effective speed of 17 km/h not available (changes UNBOOSTED to BOOSTED MODE)


Page 41/43

Gear

Num

ber

and r

ange

Pow

er

Dra

wbar

pull

Spe

ed

Eng

ine s

pee

d

Fan s

pee

d

Slip

of w

hee

ls

and/o

r tr

acks

Specific

fu

el

consum

ptio

n

Specific

energ

y

Specific

rea

gen

t

consum

ptio

n

Temperature Atmospheric conditions

Fuel

Coola

nt

Eng

ine o

il

Tem

pera

-

ture

R

ela

tive

hum

idity

Pre

ssure

kW kN km/h min-1 min-1 % g/kWh kWh/l g/ kWh

°C °C °C °C % kPa

3.3.2 FUEL CONSUMPTION

3.3.2.1 in selected gear/speed setting nearest 7.5 km/h, at maximum power at rated engine speed

8.0 91.54 42.70 7.72 2100 1380 5.8 294.2 2.83 N/A 40 79 98 5 57 98.8

3.3.2.1.1 75 % of pull corresponding to maximum power at rated engine speed

8.0 69.59 31.85 7.87 2240 1440 4.2 326.1 2.55 N/A 45 79 105 6 55 98.8


8.0 46.76 21.17 7.95 2270 1320 3.5 382.7 2.18 N/A 46 79 101 9 40 98.8

3.3.2.1.3 highest gear/speed setting at reduced engine speed able to achieve both 3.3.2.1.1 and 3.3.2.1.2 ; same pull and travelling speed as in 3.3.2.1.1

8.5 69.51 32.18 7.78 2040 1920 4.2 302.2 2.75 N/A 47 79 104 9 32 98.8

3.3.2.1.4 same gear/speed selection as 3.3.2.1.3 at reduced engine speed; same pull and travelling speed as in 3.3.2.1.2

8.5 47.23 21.33 7.97 2070 1260 3.2 352.9 2.36 N/A 47 79 102 7 52 98.8

3.3.2.2 in selected gear/speed setting nearest between 7 km/h and 10 km/h at rated engine speed

10.0 91.00 33.49 9.78 2100 1260 4.6 319.4 2.61 N/A 46 80 104 9 45 98.8


10.0 68.78 25.00 9.91 2240 1380 3.8 334.3 2.49 N/A 49 79 105 10 35 98.8


10.0 46.51 16.79 9.98 2270 1380 2.8 385.5 2.16 N/A 49 79 104 11 34 98.8

3.3.2.2.3 highest gear/speed setting at reduced engine speed able to achieve both 3.3.2.2.1 and 3.3.2.2.2 ; same pull and travelling speed as in 3.3.2.2.1

10.5 68.63 25.25 9.78 2050 1380 3.6 302.3 2.75 N/A 47 79 101 10 33 98.8

3.3.2.2.4 same gear/speed setting as 3.3.2.2.3 at reduced engine speed; same pull and travelling speed as in 3.3.2.2.3

10.5 46.36 16.71 9.99 2070 1260 2.9 349.8 2.38 N/A 47 79 99 10 37 98.8


Page 42/43

4 OPTIONAL TEST RESULTS

4.1 Engine test

Optional P.T.O. test (boosted, engine rated speed 2100 min-1 at unboosted and boosted)

Reagent consumption during Power take-off testing

4.2 Optional test results

4.2.1 Measurement of noise level at the driving position according to OECD Code 5

Date of test: 29 September 2015

Location of test: BLT Wieselburg

Version of Code 5 used: July 2014

Approval number: N/A

Date of approval: N/A

Make / model / type of Sound level meter: RION / NL / 31

Type of track: Concrete

Four wheel drive engaged windows closed:

Gear Test

Condition

Engine speed Measured traveling

speed Sound level

[min-1 (rev/min)] [km/h] [dB(A)]

F1 / 7.8 without load 2310 7.6 71

Four wheel drive engaged windows open:

Gear Test

Condition

Engine speed Measured traveling

speed Sound level

[min-1 (rev/min)] [km/h] [dB(A)]

F1 / 7.8 without load 2310 7.6 82

5 REPAIRS AND ADJUSTMENTS

None


Page 43/43

6 REMARKS

Boosted Power Take – Off (P.T.O.) Operation This vehicle is equipped with an electronically – controlled engine Power Management ™ system that monitors and boosts engine power output in certain circumstances, as engine load increases. This is achieved by electronically changing the characteristics of the engine power – speed curve. The engine Power Management function (“boosted” power level) becomes active in the higher transmission gear (mechanical range 2). The system is also activated once power transfer through the rear P.T.O. exceeds a pre – set level (and forward speed exceeds 0.5 km/h), for mobile P.T.O. – driven implement applications. An over – ride system is provided to enable P.T.O. operation at the “boosted” power level whilst the vehicle is stationary and to achieve rated engine speed, for test purposes. The results of such a P.T.O. power output test are presented in this report. Engine rated Speed Management This vehicle is equipped with an electronically – controlled engine Speed Management ™ system that monitors and limits the engine speed in certain circumstances to increase fuel economy. The rated engine speed of 2200 rpm is limited to 2100 rpm in many cases. Exemptions to this rule where the “extra speed” becomes active are ... + in the manual mode of CVT transmissions (regardless if P.T.O. is engaged or not) The engine speed is controlled/limited to 2100 rpm for drawbar performance test as well as for many other conditions not part of the OECD test code like ... + in the auto mode of CVT transmissions + when P.T.O. is engaged (with CVT and auto mode) Date of test report: 26 September 2016

Documents

TRACTOR PERFORMANCE TEST - Francisco Josephinum · Tractor: CASE IH PUMA 175 CVT BLT reference number: 007-CIH/15 - OECD Code 2 Page 3/43 Foreword: CASE IH PUMA 175 CVT tractors and