Upload
irwan-joe
View
220
Download
0
Embed Size (px)
Citation preview
7/29/2019 Track Detail Procedure English
1/40
INDONESIAN RAILWAY TECHNICALSTANDARD
ONDETAILED PROCEDURE FOR TRACK
STRUCTURE DESIGN
7/29/2019 Track Detail Procedure English
2/40
Indonesian Railway Technical Standard Track : Detailed Procedure
Table of Content
1. Scope 1
2. Objective 1
3. Definition 1
4. Basic Principle 2
5. Procedure for Track Structure Design 3
6. Loading 6
6.1 Application of Load 6
6.2 Train load in the straight line section 6
6.3 Train load in the curved section 7
6.4 Design load conditions on Combination of train loads 87. Design specifications of Track materials 11
7.1 General 11
7.2 Rail 11
7.3 Sleepers 12
7.4 Rail Fastening 13
7.4.1 F type and other similar fastening 13
7.4.2 Fastening Apparatus with Dog Spikes 14
7.4.3 The Other Fastening Apparatus 14
7.5 Ballast Materials 14
7.6 Roadbed 15
8. Examination on Excessive loads 16
8.1 General 16
8.2 Examination on Rail bending stress 16
8.2.1 The first method of examination of rail bending stress 16
8.2.2 The second method of examination of rail bending stress 17
8.3 Examination on Roadbed Strength 18
8.3.1 The First method of examination of Roadbed strength 18
8.3.2 The second method of examination of roadbed strength 19
8.4 Examination on Cracks in PC Sleeper 19
8.5 Examination on Cracks in Track slab 20
8.6 Examination on Damage to Rail Fastening 20
8.7 Examination on Occurrence of Sudden Irregularity of Alignment 21
8.8 Examination on Push-out and Pull out of Dog spike without Base Plate 22
8.9 Examination on Pull-out of dog spike with base plate 24
i
7/29/2019 Track Detail Procedure English
3/40
Indonesian Railway Technical Standard Track : Detailed Procedure
9. Examination on Repeated load 25
9.1 Examination on Development of Irregularity of Longitudinal level of rail 25
9.1.1 Examination with the First Method 25
9.1.2 Examination by the Second Method 27
9.2 Examination on Development of Irregularity of Alignment 28
9.2.1 Allowable Development of Alignment Irregularity 28
9.2.2 Estimated Development of Alignment Irregularity 30
9.2.3 Examination on Development of Alignment Irregularity 30
9.3 Examination on Damage to rail holding part of the rail fastenings and lateral pressure
receiving part of the rail fastenings 31
9.3.1 Examination on Damage to Rail Holding Part of the Rail Fastenings 31
9.3.2 Examination on Damage to Lateral Pressure Receiving Part of the RailFastenings 31
9.3.3 Examination on Rail Pad 32
10. Examination on Buckling Safety 33
11. Structure of Turnout 34
12. Additional Rule 35
ii
7/29/2019 Track Detail Procedure English
4/40
Indonesian Railway Technical Standard Track : Detailed Procedure
List of Table
Table 5-1 Test of factor 3
Table 6.4-1 8
Table 6.4-2 9
iii
7/29/2019 Track Detail Procedure English
5/40
Indonesian Railway Technical Standard Track : Detailed Procedure
1.Scope
(1) These detailed procedures shall be applied to the track structure design intended fornew installation, improvement of the track, speed-up of trains or rolling stocks, increase
in transportation capacity etc, and to confirmation of the obtainable strength and the
workable mode of maintenance of the track.
(2) These detailed procedures shall be applied to both of the existing lines and the newlines.
(3) In case that application of each of the procedures on As is basis (i.e. without anymodification thereto) proves impractical, or use of the new technology alreadydeveloped is apparently more suitable, after careful examination/study, application of
the method different from the detailed procedures and considered the most suitable may
be used.
2. Objective
The objective under the Detailed Procedures is to design the track structure in such a manner
that it shall be so designed that it can ensure not only the safety in train operation, but efficient
and economical management, as well.
3. Definition
(Not used)
1
7/29/2019 Track Detail Procedure English
6/40
Indonesian Railway Technical Standard Track : Detailed Procedure
4. Basic Principle
(4) The track structure shall bear the train load and guide a train or rolling stock, inconnection with which, the operating stability and the ride comfort of a train of rolling
stock shall be fully secured. Therefore, full attention shall be paid to the strength,
durability of the materials building up the track system and the irregularity of track, in
track structure design.
(5) For ballast tracks, maintenance against development of track irregularity due torepeated operation of trains or rolling stocks, is absolutely necessary. Hence, track
structure shall be decided, taking into full account, such factors as the state of the track
concerned, the maintenance method, the cost/expenses to be incurred thereby, etc.
2
7/29/2019 Track Detail Procedure English
7/40
Indonesian Railway Technical Standard Track : Detailed Procedure
5. Procedure for Track Structure Design
In designing the track structure, any of the following items shall be fully considered and the
requirements specified therein, shall be met with.
(6) Examination on Stress being Generated to Track Materials and PanelsWith regard to excessive load and repeated load accompanied by operation of a train or
rolling stock, the stress being generated to each track material shall be calculated taking
into consideration the track structural conditions, the rolling stock and the track
situations and so on. Appropriateness of the track structure shall be judged, by
comparison of the value calculated above and the permissible values of fatigue anddestructive strength of the material obtained from the safety in train operation.
Depending on the curve passing speed of a train or rolling stock, abruptly occurring
irregularity to track alignment shall also be checked and confirmed.
Depend on track type and condition, type of material use and operation condition, the
items for confirmation shall be specified in the following table 5-1.
Table5-1 Test of factor
Items and Methods for
Confirmation in Design of Track Structure
(Used for both existing line and Shinkansen line)
Condition for confirmation
Item for confirmation
New railway track, material or
new operation condition
New/Rehabilitation
with existing
operation condition
Examination on rail
bending stressO X
Examination on pressure
to roadbedO X
Examination on crack to
PC sleeperO X
Examination
on excessive
load
Examination on crack to
slabO X
3
7/29/2019 Track Detail Procedure English
8/40
Indonesian Railway Technical Standard Track : Detailed Procedure
Examination on damage
to rail holding and lateral
force receiving part of rail
fastenings
O X
Examination on
occurrence of rapid
alignment irregularity
O (Confirmed by First method)
Examination on Dog
spikes push-out and pull-
out
O (Confirmed by First method)
Examination on
development of
longitudinal level
irregularity
O O
Examination development
of alignment irregularity(Confirmed by First method, if necessary)
Examination
on repeated
loadExamination on damage
to rail holding and lateral
pressure receiving parts of
rail fastenings
O X
Examination on buckling
safetyO X
Note: The items marked with (x) shall be applied to the existing lines under the conditions described in
detailed procedures (Regulation) hereof.
(7) Examination on Development of Irregularity of Ballast TrackThe development of the track irregularity due to repeated operation of trains or rolling
stocks (Level, Alignment) shall be estimated by the track structural and the train load
conditions, and the estimated value shall be compared with the permissible value of the
track irregularity obtained from the target level of maintenance in respect of the rolling
stock and its operating situation and the safety in operation and the ride comfort, and
appropriateness of the track structure shall be judged by the same comparison.
(8) Examination on Buckling Safety
4
7/29/2019 Track Detail Procedure English
9/40
Indonesian Railway Technical Standard Track : Detailed Procedure
Regarding the increase in Axial force in rail due to rise in temperature, the buckling
safety of track shall be checked and consequently appropriateness of the track structure
shall be judged.
(9) Structure of TurnoutsStructure of turnouts shall be checked and confirmed, in terms of whether or no, they
are so structured or shaped that they can guide a train or rolling stock into the main line
track side or the branch line side and let it pass through.
5
7/29/2019 Track Detail Procedure English
10/40
Indonesian Railway Technical Standard Track : Detailed Procedure
6. Loading
6.1 Application of Load
Application of load shall be done according to the following:
(1) For the examinations on development of track irregularity and on stress beinggenerated to the track materials, mainly train load shall be taken into consideration.
Regarding the examination on the buckling stability, what shall be considered as a
main factor is Axial force in rail.
(2) Train load is the load inflicted from the car wheel to the rail, being divided into thevertical load right angled to the track surface (wheel weight) and the lateral load in
the horizontal direction (lateral stress). Train load is also classified into two kinds of
loads, i.e. those for the straight line section and for the curved line section, in terms
of kind of load inflicting factors. Furthermore, it is divided into the static load
obtained from the rolling stock operating conditions and the track characteristics and
the dynamic load followed by track irregularities, etc.
(3) By combination of the train loads as specified in the preceding, the train loadconditions to be used in Examination on excessive train load and Examination on
Repeated train load shall be determined.
(4) Only temperature load shall be used as the load inflicted in the axial direction inexamining the buckling stability in the track. However, in case of the examination of
rail-creep, brake load and start load shall be considered.
(5) In case that the value actually measured is obtained through speed increasing test,etc., the actual value may be used.
6.2 Train load in the straight line section
(1) Vertical Train Loada. Vertical train load (Wheel load) at the straight line section is expressed as the
total of the static and the dynamic loads.
6
7/29/2019 Track Detail Procedure English
11/40
Indonesian Railway Technical Standard Track : Detailed Procedure
b. As the static load value, the static wheel load (1/2 of the axial load) shall be used.c. As the dynamic load value, a formula established by fully considering the
following two factors, shall be used.
i. Inertial force accompanied by vertical vibration of car body occurring fromirregularity to longitudinal level.
ii. Shock due to vertical vibration of the mass under the spring which supportthe vehicle (no suspended load) being caused by the unevenness between
wheel and rail
(2) Lateral Train Loada. Assuming that as the static load, side to lateral load (lateral force) will not exist,
only the train load as the dynamic load, shall be considered.b. For the dynamic load, a formula established in the view of the inertia force of
lateral vibration of car body due to irregularity of alignment, shall be used.
6.3 Train load in the curved section
(2) Vertical Loada. Vertical train load (wheel load) is expressed as the total of the static and dynamic
loads.
b. As the static load, increase and decrease by the load due to excessive centrifugalforce shall be considered, in addition to the static wheel load.
c. The dynamic load in the curved section shall be the same as Section 6.1.(3).(3) Lateral Load
a. Lateral load (lateral force) in the curved section, is expressed as the total of thestatic and the dynamic loads.
b. As the static load, a formula established with the view of curve changing lateralforce and lateral force due to excessive centrifugal force, shall be considered.
c. As the dynamic load, a formula established with the view of inertia forceaccompanied by lateral vibration of car body, shall be considered. However, in
case of the track with ordinary rail joints, the dynamic lateral force mainly from
axial shock occurring at the area near the joints shall also be taken into
consideration.
7
7/29/2019 Track Detail Procedure English
12/40
Indonesian Railway Technical Standard Track : Detailed Procedure
6.4 Design load conditions on Combination of train loads
(1) Load conditions in examination of stress of the materials against excessive loada. As the load conditions when examining the stress of a track material against its
excessive load, excessive load rarely taking place in the section concerned shall
be calculated.
b. The value of the dynamic vertical and lateral load shall be three times as much asthe standard deviation.
c. In calculation of the dynamic vertical and lateral (right to left) load values, thetarget values for irregularities of longitudinal level and of alignment (as specified
in the following table, the same hereinafter) shall be used.
Table 6.4-1
Description Safety Limit Remarks
Vertical vibration
Full amplitude4.0 m/s2
Lateral Vibration
Full amplitude
3.0 m/s2 in case ofh 0.60 m/s2(4.2 2h) m/s
2 in case ofh > 0.60 m/s2
h: Lateral static
(regular) acceleration
d. The static vertical load shall be used as the representative vertical load that isput on with the combination of lateral loads of the sleeper lateral stress or the rail
lateral stress.
(2) Load conditions in Examination of stress of a material against repeated loada. As the load conditions for examination of the material against repeated load,
considerable load often occurring in the section concerned shall be calculated.
b. Vertical and lateral dynamic load value to be used for examination of stress of thematerial shall be the same as that of the standard deviation.
c. In calculation of the vertical and lateral dynamic load, the target values for thesafety in irregularities of longitudinal level and alignment of track.
d. As the vertical load that is combined with lateral load of the sleeper lateral stressor the rail lateral stress, etc., its static load value shall be used.
(3) Load conditions for Examination on Development of Irregularities of Track.
8
7/29/2019 Track Detail Procedure English
13/40
Indonesian Railway Technical Standard Track : Detailed Procedure
a. The load conditions for examination on development of irregularities of trackshall be calculated for the whole train load in the section concerned.
b. The vertical and lateral dynamic load values to be used for estimation ofdevelopment of track irregularities (longitudinal and alignment) shall be three
times as much as the standard deviation beside its static load values.
c. In calculation of the vertical and lateral dynamic loads, the target value in the ridecomfort index(as specified in the table attached hereto, and referred to as the
same, hereinafter) shall be used.
Table 6.4-2
Target of ride comfort Remark
Vertical vibrationFull amplitude
2.5 m/s2
h: Lateral2.0 m/s2 in case ofh 0.60 m/s2 Lateral vibration
Full amplitude
static
(regular)(3.2 - 2h) m/s
2 in case ofh > 0.60 m/s2
acceleration
d. For the vertical load that is put on with the lateral load in estimation ofdevelopment of alignment irregularities, the static load value shall be used among
the two types (i.e. dynamic and static).
(4) Track Design load arrangementRegarding the vertical load and the lateral load, the factor of Track Design load
arrangement shall be considered, in case that the nearest wheel are within the
distance of 2.5m.
(5) Track Design load in the axial directiona. It shall be assumed that the temperature load is generated, in case that the rail
encounters a change in temperature when it is held in the direction of the axis and
it is inflicted evenly in the axial direction of rail and uniformly to the whole
cross-section of rail.
b. Amount of temperature load in the long rail installed section, shall be obtained bythe following formula.
)( ottEAP =
Where, P : Rail axial force
9
7/29/2019 Track Detail Procedure English
14/40
Indonesian Railway Technical Standard Track : Detailed Procedure
E : Youngs modulus of rail steel
A : Rail cross-section modulus
: Rail steel liner expansion coefficient
t : Long rail temperature
to : Installation temperature of long rail
(6) Braking Load and Starting LoadRegarding braking and starting loads, the corresponding specifications in the Design
standard on concrete structures, steel and composite structures shall apply.
10
7/29/2019 Track Detail Procedure English
15/40
Indonesian Railway Technical Standard Track : Detailed Procedure
7. Design specifications of Track materials
7.1 General
Design specifications to be used for track structure shall be as per the followings, but in
the event that application of these values is considered impractical, the value obtained by
relevant test or experiment, etc. and regarded as appropriate may be applied.
7.2 Rail
(1) Bending stiffness of rail(Vertical: EIx and Horizontal: EIy)Type of Rail EIx ( 10
8N-cm2) EIy ( 108N-cm2)
60kg 648.9 107.5
R54 492.7 87.7
50N 411.6 67.6
50kg 366.2 79.2
R42 290.6 49.4
40N 289.4 48.337kg 199.8 47.7
R33 217.7 31.6
30kg 126.8 31.9
(2) Section modulus of railZx (cm
3)Type of Rail
60kg 397R54 313
50N 274
50kg 261
R42 190
40N 197
37kg 164
R33 151
11
7/29/2019 Track Detail Procedure English
16/40
Indonesian Railway Technical Standard Track : Detailed Procedure
30kg 116
(3) Rail lateral stiffnessJ (cm4)Type of Rail
60kg 512
R54 418
50N 322
50kg 377
R42 235
40N 230
37kg 227
R33 151
30kg 152
(4) Material coefficient of steel used for design calculationYoungs modulus 210 GPa
Shearing elasticity coefficient 81 GPa
Poissons ratio 0.3
1.1410-5/oCLine expansion coefficient
7.3 Sleepers
(1) PC Sleepers
a. For any other calculation than bending stress, PC sleeper shall be treated as arigid body.
b. The standard coefficient of friction between sleeper and ballast shall be 0.65.(2) Wooden Sleepers
a. The standard compressive spring coefficient of wooden sleeper shall be100.0MN/m.
b. The standard coefficient of friction between rail and sleeper shall be 0.60.c. The standard coefficient of friction between sleeper and ballast shall be 0.65.
12
7/29/2019 Track Detail Procedure English
17/40
Indonesian Railway Technical Standard Track : Detailed Procedure
(3) The Others
a. Firstly, the specifications shall be determined, according to the requirement fordesign of mass, shape and dimensions etc.
b. In case that assumption of sleeper as a rigid body is impossible and springcoefficient to compression and bending of sleeper itself is unknown, then it may
be decided, by carrying out tests or experiments.
7.4 Rail Fastening
7.4.1 F type and other similar fastening
(1) The fastening/Clipa. Lateral spring and Tip spring constants shall be obtained by theoretical
calculation or experiment.
b. Initial fastening capability shall be obtained by theoretical calculation.c. The standard coefficient of friction between rail and fastening spring shall be
0.25.
d. The standard coefficient of friction between fastening spring and pad shall be0.65.
(2) Rail Pada. Spring coefficient shall be obtained, depending on the quality, shape etc. of
materials to be used.
b. As regards the pads as specified in JIS standard, etc., the values as indicated inthe same standard, shall be applied.
(3) Spring Supporters (Support Plate)The compressive strength of spring supporter shall be obtained, according to JIS
E 1118: Test on Compressive strength with necessary modification.
(4) Compressive Strength of Support PlateCompressive strength of support plate shall be obtained, according to JIS E 1118:
Test on compressive strength with necessary modification.
(5) Pull-out Resistance of Buried Plate (Embedded Insert)
13
7/29/2019 Track Detail Procedure English
18/40
Indonesian Railway Technical Standard Track : Detailed Procedure
Pull-out resistance of buried plate shall be obtained, according to JIS E1118: Test
on pull out resistance with necessary modification.
7.4.2 Fastening Apparatus with Dog Spikes
(1) Clear indication shall be made as to whether or no tie plates are used.(2) As regards the factors or items that are used in design calculation for use of tie
plates and specified in JIS standard etc., the values as indicated in the same
standard shall be applied, and regarding the factors or items not specified in JIS
standard, etc., the dimensions actually measured shall be applied.
(3) Push out limit of dog spike shall be set as its standard at 7.0 kN.(4) Pull out limit of dog spike shall be set at 1.0mm as its standard.7.4.3 The Other Fastening Apparatus
In case of use of the fastening apparatus corresponding to neither 3 nor 4 above, the
design values shall be obtained, by theoretical calculation and performance of test/s.
7.5 Ballast Materials
In case of use of crushed stones, the design values shall be obtained as follows:
(1) The width actually measured shall be treated as the standard for the width of ballastshoulder. Nevertheless, in a case (such as new installation of rail) that such a
measurement is impossible, the design value may be used.
(2) The standard unit mass shall be fixed at 1.7 t/m3.(3) Ballast spring constant shall be 200.0MN/m as its standard regardless of ballast
thickness
14
7/29/2019 Track Detail Procedure English
19/40
Indonesian Railway Technical Standard Track : Detailed Procedure
7.6 Roadbed
Such soil roadbed, stabilized roadbed, other types of roadbed, site ground roadbed as
specified in Standard on Design of Soil Structures and the concrete-structured roadbed
as specified in Standard on Design of Concrete Structures shall be treated as the
Standard of Roadbed, whose design values shall be obtained as follows:
(1) With regard to soil roadbed, stabilized roadbed, other type of roadbed, site groundroadbed, the geometrical features shall be clarified, and then a variety of factor values
to be used for design calculations shall be obtained, by performing tests etc.
a. The test method shall be as per Standard Design of Earth Work. However, theallowable bearing capacity of soil roadbed may be fixed at 2.88 kg/cm
2
.b. K30 value of plate bearing testc. Kohn Penetration resistance valued. Allowable bearing capacity of roadbed
(3) Regarding concrete structured roadbed, it shall be treated as a rigid body, and thevalues referred to in (1) above, may be fixed as infinite.
(4) In the event of use of any other roadbed than (1) and (2) or, of insertion of anintermediate material between ballast and roadbed and further it being impossible to
classify into the rigid structure, the following items shall be determined/established
by performing the necessary tests, etc.
a. Spring coefficient of the roadbed and the intermediate materialb. Allowable bearing capacity of the roadbed and the intermediate material
15
7/29/2019 Track Detail Procedure English
20/40
Indonesian Railway Technical Standard Track : Detailed Procedure
8. Examination on Excessive loads
8.1 General
With regard to examination of excessive loads, the strength conforming to the train load,
shall be secured and confirmed.
(1) Rolling stocks entering the line for the first time(2) At the time of new laying and improvement of track (Examination to be conducted by
use of the maximum speed)
(3) At the time of improvement of the maximum speed or increase of the curve passingspeed, in existing lines.
8.2 Examination on Rail bending stress
Among the line divisions where the highest speed train or rolling stock in the line sectionconcerned(heaviest one among the highest speed trains) and the heaviest train or rolling
stock run at their maximum speed, the smallest radius curve shall be picked up, in the
case of which, the rail bending stress under the excessive load and allowable stress shall
be calculated, and examined.
8.2.1 The first method of examination of rail bending stress
When examining the rail bending stress by the first method, it shall be carried out
according to the following procedure.
(1) According to the real sudden rupture strength and the fatigue limit, figures/data ondurability limit shall be obtained.
(2) Residual stress shall be considered.(3) Temperature stress shall be considered for regular rail and long rail respectively.
16
7/29/2019 Track Detail Procedure English
21/40
Indonesian Railway Technical Standard Track : Detailed Procedure
(4) From the figures on durability limit, the allowable stress of rail against train loadshall be obtained.
(5) Additional stress occurring from lateral force shall be taken into account.(6) Allowable stress for wheel load shall be calculated, and be multiplied by 0.8 into
Permissible bending stress of rail (P). Furthermore, rail fatigue limit of half
amplitude in calculation of the allowable bending stress value (fatigue limit in
terms of each type of rail) may be as per the following table, instead of the
preceding (1) through (4).
Fatigue limit of rail (Mpa)Type of Rail
Regular rail Long rail
R60 130 112
R54 130 112
50N 130 112
50 kg 126 107
R42 130 112
40N 130 11237kg 122 102
30kg 122 102
(7) Rail bending generated stress (ao , ai) shall be calculated and obtained.(8) The safety shall be confirmed, from and in the light of the relationship ofao
p, aip.
p ; Allowable bending stress
8.2.2 The second method of examination of rail bending stress
The second method of examination shall be as per the following procedure:
(1) Allowable rail bending stress (p) shall be fixed as the following.-Long rail : 130 Mpa (1300 kg/cm2)
17
7/29/2019 Track Detail Procedure English
22/40
Indonesian Railway Technical Standard Track : Detailed Procedure
-Standard rail : 160 Mpa (1600 kg/cm2)(2) Assuming the track deformation as a continuous elasticity supporting model, the
maximum rail bending moment, shall be obtained from the influence line.
(4) It shall be confirmed that the rail stress (i) of which are generated by themaximum rail bending moment, and allowable bending stress should satisfy the
relation materialized in the following formula.
i p
p ; Allowable bending stress
8.3 Examination on Roadbed Strength
Among the curves where the highest speed train ( the heaviest rolling stock in the highest
speed train) and the heaviest rolling stock run through at the highest speed, the smallest
radius curve shall be picked up, against which, the roadbed- affected stress under the
excessive load and the allowable stress shall be obtained, and the roadbed strength shall be
examined.
8.3.1 The First method of examination of Roadbed strength
When examining the roadbed strength with the first method, the procedure thereof
shall be as per the following:
(1) The examination of roadbed strength shall be conducted by the followingformula, with the values of the pressure to roadbed being calculated by the design
load and the allowable bearing capacity of roadbed.
Psmean qa
Where, Psmeam : Average pressure to roadbed
qa : Allowable bearing capacity of roadbed
18
7/29/2019 Track Detail Procedure English
23/40
Indonesian Railway Technical Standard Track : Detailed Procedure
(2) The allowable bearing capacity of roadbed shall be calculated/obtainedseparately, according to Standard on Design of soil structures and Standard on
Design of foundation structures.
(3) Regarding the roadbed structured by any other than the material assumed as arigid body, the method of (1) above, shall be applied.
8.3.2 The second method of examination of roadbed strength
When examining the roadbed strength with the second method, the procedure thereof
shall be as per the following:
(1) The allowable bearing capacity of roadbed may be applied at 2.88kg/cm2.(2) Assuming the rail deformation as a continuous elasticity supporting model, the
maximum pressure to roadbed (Pbdy) shall be obtained, and it shall also satisfy the
following formula, with the allowable bearing capacity of roadbed.
Pbdy qa
8.4 Examination on Cracks in PC Sleeper
Among the curves where the highest speed train in the line division concerned (the
heaviest rolling stock in the highest speed train) and the heaviest rolling stock run at the
highest speed, the smallest radius curve shall be picked up, against which, the stress under
the excessive load, shall be calculated/obtained, and then cross-examined with the
acceptable stress obtained through the following:
(1) Bearing pressure of ballast shall be assumed.(2) The acceptable value of the stress generated by the excessive load shall be obtained
from the value of effective pre-stress.
19
7/29/2019 Track Detail Procedure English
24/40
Indonesian Railway Technical Standard Track : Detailed Procedure
8.5 Examination on Cracks in Track slab
Cracks in Track slab shall be examined in the following manner.
Among the curves where the highest speed train in the line division concerned (more
specifically, the heaviest rolling stock in the highest speed train) and the heaviest rolling
stock run at the highest speed, the smallest radius curve shall be picked up, towards
which, the stress being generated by excessive loads being inflicted when the said rolling
stocks run at the maximum speed, shall be calculated/obtained, and then cross-examined
with the acceptable stress obtained from the following:
(1) RC Track SlabStress of reinforcement bar shall be calculated from the moment being generated by
the load, but shall be within the limit of the allowable steelstress (1,800kg/cm2).
(2) PRC Track SlabStress of reinforcement bar shall be calculated from the moment being generated by
the load, but shall be within the limit of the allowable steel stress (1,000kg/cm2) for
RRC slab.
8.6 Examination on Damage to Rail Fastening
Among the curve sections where the highest speed train (the heaviest rolling stock in the
highest speed train) and the heaviest rolling stock run at the maximum speed, the smallest
radius curve shall be picked up, towards which, the stress being generated by excessive
loads when the said rolling stocks run through it at the maximum speed, shall be
calculated/obtained, and then examined in comparison with the allowable stress values for
the following:
(1) Examination on Damage to Rail Holding PartThe stress generated due to excessive loads or counter-action of the rail holding part
to prevent irregular inclination of rail from occurring, shall be calculated/obtained,
and then examination shall be made, in the form of comparison of the allowable stress
or the permissible load, according to the following procedure.
20
7/29/2019 Track Detail Procedure English
25/40
Indonesian Railway Technical Standard Track : Detailed Procedure
a. Limit line for durability of fastening springs shall be calculated and organized byreal sudden rupture strength, fatigue limit, time limit, elasticity limit and yield
point etc.
b. Initial fastening stress of the spring and bolt shall be considered.c. From the second sudden rupture limit and the second exhaustion limit in the
durability limit figure, the allowable stress of the spring to the load shall be
calculated and obtained. Further, in case of impossibility of theoretical
calculation of the stress generated to the springs, etc., it may be obtained by tests.
d. According to JIS E1118: Test on Pull-out resistance, the pull-out load limit toburied plate (embedded insert) shall be calculated, and the allowable load shall be
fixed at 1/4 as much as the said pull-out resistance.e. From the fatigue limit and the yield point in the bolt durability figure, the
allowable stress of the fastening bolt to the load shall be obtained.
(2) Examination on Damage to Lateral Force Receiving Part of Rail FasteningsThe stress being generated to lateral force receiving part shall be calculated/obtained,
under the excessive load and then examined by comparison thereof with the allowable
stresses obtained in the following:
a. Durability limit Figure of fastening springs shall be calculated/obtained by realsudden rupture strength, fatigue limit, time limit, elasticity limit and yield point.
b. Initial fastening stress of the fastening spring and the support plate or receivingplate shall be taken into account.
c. From the second sudden rupture strength limit and the second exhaustion limit inthe durability limit figure of fastening springs, the allowable stress to the load
shall be obtained.
d. According to JIS E1118: Test on Compressive Strength, the bearing pressurelimit of support plate or receiving plate shall be calculated/obtained, and the
allowable stress shall be half the said limit.
8.7 Examination on Occurrence of Sudden Irregularity of Alignment
In case of operating a train or rolling stock at more than 20 km/h higher speed than the
basic speed specified in Basic Velocity under speed restriction through curves in the table
21
7/29/2019 Track Detail Procedure English
26/40
Indonesian Railway Technical Standard Track : Detailed Procedure
on train operating speed, the safety towards occurrence of sudden irregularity of track
alignment shall be examined. The examination shall, ini principle, be conducted by the
lateral pressure to sleeper due to excessive loads and the lateral ballast resistance of
sleeper under consideration of the differences according to the track structures and load
conditions. However, another examination method may be used, so long as it can satisfy
the formulas related to the design load.
Rail pressure by static wheel load, lateral stress to rail from excessive lateral force, lateral
ballast resistance shall be calculated/obtained, and it shall be confirmed that the following
formula is met with.
85.0120
21