Follow us on TWITTER http://twitter.com/mauisails and FACEBOOK http://www.facebook.com/MauiSailsHawaii www.MAUISAILS.com

Our Experience, Your Reward

Please take care of Your Sail

Take care to keep your sail out of the sun when at rest or in storage. The use of a rig cover will prevent degradation.

Thread the pulley according to the instructions. Be sure to thread the rope correctly to ensure smooth downhauling and no cross threading of the rope.

You need to have a mast extension with at least 2 pulley’s and a cleat. Take your downhaul line from the dead end on

your base to the same side of the forward pulley wheel, feeding up. Then feed the rope into the pulley next to the cleat from down to up.

6:1 Tack Pulley Fitting

Feed the rope up to the pulley wheel farthest from the mast (towards the clew of the sail), inserting from the same side,

ie up to down. Then feed the rope back down the pulley on the base which is farthest away from the cleat, from up to down. This makes a correct lead with no twist.

Then go up and over the middle wheel and back into the cleat. You are now ready to apply downhaul tension.

1

2

3

Important Details

Batten Tension System Correct batten tension is applied using the stainless steel hex key supplied in the mesh pouch in the tack fairing. The screw should be tightened clockwise to remove wrinkles in the batten pockets. More batten tension is required in the lower part of

the sail, less batten tension is required in the upper part of the sail. Tension battens before rigging.

Removal and replacement of battens1. Release tension with counter-clockwise turns

of the tool.2. Slip string off the tensioner.3. Remove batten and tensioner.

To reinstall battens1. Insert batten with tensioner on and the screw

flush in the piece. Push the batten in as far as possible.

2. Slip the string up into the tensioner groove and tighten the screw to restore normal batten tension.

Uphaul Access holeThere is a small opening near the tack of the sail to insert your uphaul and place around the mast extension.

Tensioner keyThe tensioner key is stored in a mesh pouch inside the fairing. This is also good for containing the tail of your downhaul rope.

Tack StrapThe tack strap is placed around your mast base (mast foot) and tightened moderately for slalom sailing. You may use this adjustment to develop extra fullness in the lower sections

and slightly increase leech tension when using the larger sizes for Formula sailing.

Recommended mastTesting and development has been done using the MauiSails SRS 100 Carbon race masts. To get the most out of your new race sail, you should use this mast. Other masts with similar diameters and bends will give acceptable but not necessarily optimum performance.

• Tocleanyoursail,usefreshwaterandmildsoap,notharshsolvents or abrasive cleaners.

• Alwaysfixanysailwithsmallholesortears,orriskeasilyenlarging the damage.

• Storeyoursailinthebag,cleananddry,rolledtightly.Donottocrush or crease it.

• Adroportwooflightoilonyourtackpulleywilllimitcorrosionand reduce friction.

Get Your Reward, Get MauiSails

How to read specification box

When rigging your MauiSails you must consider the mast, extension, and boom length you should use. The answer for those questions is printed in the lower part of the sail. Those are recommended settings we found the best to get the correct amount of downhaul and outhaul forthegeneralrangeofuse.Let’sgothroughtheparametersofthespecificationbox.

Mast and IMCSThese are the two main variables that characterize the mast. It tells you how long a mast you should use and IMCS describes its stiffness.

Luff and Downhaul (dh)These two parameters are dependent on each other and together indicate how much extension you should use. Downhaul (DH) should be measured from the base of the mast to the front lower corner of the tack pulley on the sail using a ruler or tape measure. This is the absolute accuracyofyoursettingsandwillhelpyoutoachievefinetuning(seeillustrationbelow).Thebasesettingistomakesureyouhaveenoughdistance to properly tune the sail. Luff length is measured as :

Luff length = Mast length + Downhaul

BoomBoom length is the distance from the front of the mast to the edge of the sail at the clew with the boom centered in the cutout. If you set your boom at the highest point, the dimension increases. Likewise if you are at the bottom of the cutout it might be a bit shorter.

In the case where you would use an adjustable outhaul and might want to have extra boom length to flatten the sail, by all means add another few centimeters to cover.

Our Experience, Your Reward

TR-5 Rigging and Tuning

Observing and practicing correct rigging procedure will help you get on the water with the minimum of hassle and the least amount of wear and tear on your whole rig.

There are two ways to put on the cambers. Thefirstwayistodownhaul,putyourboomonfirst,thenpoponthecambers.The second way is to downhaul to about 10cm from maximum and then pop on the cambers. Both ways will be described in this rigging manual.

Get all your gear together and make sure all parts are in good shape with no visible damage. Check pins and fastenings on the mast base and universal. Check the mast for obvious dings or cracks.

Make sure your two-piece mast is fully connected at the joint.

Insert the mast from the bottom of the sail on the top of the cams.

Make sure all the zippers are closed when inserting the mast.Donotattempttoputthe cams on the mast yet. Make sure the mast is fully inserted to the top of the sail.

1

Find a clean soft area, preferably grass, and unroll the sail with the head upwind to prevent flogging.

Set the mast base and boom at the recommended positions as specifiedonthesailbagorthetackareaofthesail.

Tension the battens before you begin to rig your sail. Using the batten tensioning tool, start at the bottom and tension all nine battens with more tension on the bottom battens and less tension the top battens. Make sure there are no wrinkles under the battens and the batten pockets are stretched tight.

Rigging with the boom on first

2

Downhaulthesailuntilthemastisshowing in the boom cutout enough

to enable you to put the boom on.

Downhaulshouldbeabout8-12cmfrommaximum setting. If you have trouble putting the boom on, you may have to put on more downhaul to get the mast where youcanmoreeasilyfittheboom.

3

Get Your Reward, Get MauiSails

Once the boom is on the mast, attach the outhaul, pulling the sail flat. This

keeps the sail off the surface and protects the battens and pockets.

Now, ease the downhaul approximately 20-30cm, until the

middle of the sail is loose.

With the sail loose you can undo each zipper, reach inside, and put

gentle pressure on the batten inside the sleeve behind the cams. Pop the cams on. Before moving up to the next cam, pull the zipper closed. Begin at the foot batten and work up.

4

5

6

For the battens above and below the boom, put your hand inside the sleeve cutout and press down on the batten close to the cam. Pop the cam onto the mast. If the cam falls off, pull on a little bit of downhaul.

When the cams are on the mast, downhaul the sail to the desired

setting, and then release the outhaul slightly.

TIP : Fold up the fairing at the base to make it easier to thread the downhaul.

7

Rigging without the boom on

Downhaulthe sail with

the cams off the mast to about 10cm off maximum downhaul.

1 Start at the cam above the boom and

holding the mast with one had push the cam back and onto the mast. Then move to the highest cam. Open the zipper and push on the cam the same way.

2 Then move to the cam below

the boom and push on the cam.

3 Next open the zipper on

the lowest cam and push on the cam.

4

Once all the cams are on

the sail, put on the boom.

5 Now pull the downhaul to

the correct setting and attach the outhaul rope to the clewfitting.

6

TR-5 Sail Tuning Tips

Our Experience, Your Reward

•Sailswithoutenoughdownhaulwillfeelsluggishandheavy.Thebalance will be poor, and the power will feel high up in the rig. If you have too much downhaul, you will have very little power, and it will be hard to get upwind.•Aproperlytunedracesailonthecorrectmastwillbeveryloose

along the entire leech, becoming progressively looser as you move up the sail. •Ifyouhavetroublewithcamrotation,easeupthedownhaul

about 5mm and then see if it rotates. Cams rotate on the water not on dry land test.

•Ifyouhavetroublecontrollingtheboard,andcan’tmaintainyourdesired course or are spinning out, try more downhaul. If there is still too much pressure on your back hand, try more outhaul.•Ifyoucan’tgetanydriveupwindandtheboardwon’ttrackorlift,

try less downhaul, or more outhaul.•Ifyougowelldownwindbuthavenopowerupwind,tryabitless

downhaul.•Useshorterharnesslinesforlighterwindandflatterwater.Longer

lines work well for being overpowered and in choppy conditions.•Mostofall,payattentiontoyourfellowsailors,respect the locals

and the environment, and have fun.

On the leech there should be looseness between the battens, gradually decreasing as you go down to batten numberfive.Theluffpocketshouldbeafirmfitonthemast at the second batten.

It is recommended to use an adjustable outhaul with a race sail. You will need to adjust the tension for the various course angles, and you can use the outhaul to help you get through gusty periods or when very overpowered. Off the wind, you will need to ease your outhaul to keep power on in low apparent wind, and upwind you will want to trim the sail much flatter to get good angles and speed.

Get Your Reward, Get MauiSails

Ask Barry Spanier

Don’thesitatetocontacttheMauiSailsteamovertheforum(AskBarrySpanier)atwww.mauisails.com/forum.What’smore,onourwebsiteyouwillfindinour“FrequentlyAskedQuestions” section, we present answers for questions that our customers have asked us over the years. Check it out. Maybe youwillfindthesolutiontoyourproblemtoo!

Boom chafe reinforcement

On race sails where the batten crosses the boom, we have added a very light and extremely tough anti-chafe patch to the batten pocket to prevent wear in this area. This is in response to feedback we received in our forum.

Contact Maui Sails

Synergy Sports, Inc.810HaikuRoadSuite113PMB302

Haiku,Hawaii,96708USA

website: www.mauisails.come-mail: media@mauisails.com

Derigging

Start thinking about more wind tomorrow

1. Remove your outhaul rope off the clew pulley and remove the boom from the mast. Swing your boom away from the rig to prepare letting off the downhaul.

2. Let off the downhaul and remove the rope from the pulleys. The cams should fall off the mast at this point. If the bottom cam does not fall off, push the sleeve up and ease the cam off the mast before removing the mast completely.

3. Roll up the sail starting from the top.

Follow us on TWITTER http://twitter.com/mauisails and FACEBOOK http://www.facebook.com/MauiSailsHawaii www.MAUISAILS.com