TPV Component Specificationows2.tpv-tech.com/e_mp/uploadfile/specification/201505/T...TPV Component Specification Page 3 Form__V02 1. Transformer Incoming Inspection Key Items No

TPV Component Specification

Page 1 Form__V02

TPV PART NO. SUPPLIER PART DESCRIPTION

LI TAI TRANSFORMER

TPV : Sky Lin Approved: Frank Tung

NOTICE :

1. Any specification changed of component, especially following items: Raw Material, Process, Tooling, Factory, Label, halftone, and any

engineering changed of production, should be approved by TPV. 2. Any engineering changed of component should be in version record, provide old version parts management information to TPV if

required. 3. All raw material of supplied parts should be meet the TPV standard (RDEMS-01) or its latest version, and the requirement of regional or

country laws and ordinances.

SUPPLIER SUPPLIER PART NO. PT-019875 FACTORY 福清 SIGNATURE STAMP

VERSION RECORD VER DESCRIPTION OF CHANGE OWNER RELEASE DATE

A CHECKED AND ELEASED 謝炳煌 2015-03-04

N2 10---7,8 N6 6TS 變更為 N2 9,10---7,8 N6 5TS 謝炳煌 2015-03-11


Page 2 Form__V02

CONTENTS Item Page

Cover and Version Record 1

Contents 2

1.Transformer Incoming Inspection Key Items 3

2.TPV Transformer Coding Rule 4

3.Appearance & Mechanical Characteristics 5

4.Electric characteristics 9

5.Reliability 10

6.Packing list 11

7. Material List(Supplier BOM) 12

8.No Use Guarantee Letter(Raw material name and supplier list) 13

9.Core Dimensions & Characterics 41-44

10.Transformer Insulation System UL file 13

11.Material data sheet & UL file: Bobbin,Tape & Margin tape,Copper wire &

Triple wire,Tube,Varnish,Epoxy 19-40

12.Inspection report(Dimensionsn, Electric,Hi-pot & Insulation)

13.TPV RoHS component solderability/Resistance to soldering heat Spec 18

14.Varnish Control list & Drying SOP 45-47

15.VOC Guarantee Letter, HI-POT Guarantee ?


Page 3 Form__V02

1. Transformer Incoming Inspection Key Items

No. Item Description Remark

1 Inductance(uH or mH) Tolerance or Range

2 DC Resistance(OHM or mOHM) Tolerance or Range

3 Leakage Inductance(uH or mH) Tolerance or Range

4 Q Value MIN

5 Turn ratio Output voltage, voltage phase

6 HI-POT No damage and corona

7 Layer short test Curve can't abnormal

8 Insulation Resistance MIN

9 Construction analyze Outer layer to inner layer , wire diameter ,

Turns , Tube , Varnish .

10 Solderability Temperature , Time

11 Resistance to soldering heat Temperature , Time

12 Tensile strength Angle , Force

13 Bending strength Force, Times

14 Dimension Body size(W L T),pitch dimension ,diameter

15 Mark Insulation System / HI-POT OK / PN

16 Appearance Clean

17 Supplier output inspection

report QC pass


Page 4 Form__V02

2. TPV Transformer Coding Rule

380 G ****— ***—** *- **** A B C D E F

A：大分类：电源变压器 Main category：Transformer B：中分类 : 按机种的尺寸分类。 Sub category: Classify model size

L19T Inverter transformer, for 15-22”model L32T Inverter transformer, for 23-37”model L52T Inverter transformer, for >=40”model L19P Power transformer, for 15-22”model L32P Power transformer, for 23-37”model L52P Power transformer, for >=40”model

C：流水码，表示不同型号 Serial number for different type. 001、002、… Z99 D：厂商代码, ( Vendor code, ): E：派生码，如 (derived code , for example): 0、1、2、…Z F: 特殊码（special code） 00HF --- 无卤料件（HF part）

00TP --- TP Vision

PFC choke Coding Rule 373 G ****—***—** * - **** A B C D E F

A：大分类 : 固定电感器、电源滤波器

Main category: Choke、Line Filter B：中分类: （Sub category）

0174——电源滤波器, PFC 电感 [安规电感必须编为此中分类] Common-Mode choke coil ，PFC choke [ safety choke only ]

C：流水码： Serial number 001、002、…Z99 D：厂家代码 , Verdor code E: 流水码: 用于派生料号, 如， (Derived code, for example) 0、1、...Z F: 特殊码（special code） 00HF --- 无卤料件（HF part）

00TP ---- TP Vision


Page 5 Form__V02

Steel 78%Cu 22%

Sn 99.99% (Thickness 6 -1μ)+2

Lead Free SolderSn 98% Cu 2%

NOTE: 1.Lead Wire Composition

3, Mechanical Characteristics 3.1 Dimensions

NOTE:

1.GAP CORE TO TOP SIDE.

2.CORE中柱点胶.

3.ALL PINS 1.0TS MIN.

4.PIN 3 CUT OFF,PIN 5 CUT OFF 1/2.

3.2 Marking Contents: (1) TPV P/N : P/N (2) Vendor Name or Trade Mark : LI TAI (3) Date Code: YEAR (XX) & WEEK (XX) & CORE SUPPLIERS (XX)

（Marking date code 尾碼增加兩碼標示量產鐵芯） (4) “HI-POT OK” Model of Written Characters. (5) Insulation System Designation: CIS.04 TABLE III CLASS B（130℃） (6) Marking Standards:

P/N HI-POT OK LI TAI LT□□ CIS.04 XXXX XX

(7) Manufacture site: LTFC:Fujian,China LTSZ:Shenzhen,Guangdong,China LTSJ:Suzhou,Jiangsu,China

3.3 Technique Request: (1) The part must be dipped varnish and must be dipped in vacuum. Varnish must go through the

neighborhood layers of the coil. The coil should not loose. (2) External of part must be immaculate, marking must be clear. (3) Two cores must be aim, not shift. Core and winding should not move. (4) Script or marking orient Pin 1 . (5) Lead wire of every pin must set an individual groove. (6) The transformer is a lead free product. (7) All bobbin and winding must be covered entirely by insulation tape (8)Tube must be over margin tape, tube over bobbin 2.5mmMIN ( Ref the pic. next page.). (9) Mylay tape: 25um*5.5mmW.

NO Supplie of core 02 DMEGC 03 ACME

A = 34.0±2.0mm B = 13.5±1.0mm C = 40.5±2.0mm D = 3.5±0.3mm E1= 5.0±0.3mm E2 = 47.5±0.5mm Φd = 08*0.8±0.1mm WEIGHT IS 51.6g±2g.

WINDING DIRECTION

CORE TAPE:0.025tx22mmWx2ts MIN

EPOXY

A

MARKING

61

12

1

6

C

E1

B

76

1

7

16

7 12

E2

外圍TAPE:0.025tx38mmWx1T MIN起始和結束需重疊 8mm MIN


Page 6 Form__V02

骨架图纸 (Bobbin Dimensions):


Page 7 Form__V02

套管 / 点胶 / 磁芯背胶图示 (Tube / Epoxy / Core tape picture ):

中柱点胶（胶需布满中柱）套管外露 2.5mm MIN


Page 8 Form__V02

3.4 Schematic

3.5 Winding construction

Mylay tape: t25um*5.5mmW 1.PIN 1,2,4,5,6,11 ADDED TUBE 2.TUBE over winding 2.5mm MIN 3.6 Winding mode:

No. COIL TERMINAL WIRE GAUGE WIRE TYPE TUNS WINDING METHOD

TAPE 2T

1 N1 6---5 φ0.35 UEW 13 CLOSED 1T 2 N2 9,10---7,8 φ0.5*4 TIW-M 4 CLOSED 1T

3 N3 5---4 φ0.35*2 UEW 13 CLOSED 1T

4 N4 11---10 φ0.4*2 TIW-M 3 CLOSED 1T 5 N5 6---5 φ0.35 UEW 13 CLOSED 1T

6 N6 1---2 φ0.25 UEW 5 CLOSED 3TS 3.7 Winding direction: IT IS CLOCKWISE FROM BOTTOM SIDE Note: 1) Bare wires and insulated wires should not intersect contacts each other. (漆包线和绝缘线不能相互交叉接触） 2) Reflexed tape of copper foil :NA

N1(6--5)

N2(9,10--7,8)

N3(5--4)

N4(11--10)

N5(6--5)

TAPE 2T

TAPE 3TsN6(1--2)

TAPE 1T

TAPE 1T

TAPE 1T

TAPE 1T

TAPE 1T

PIN

PRI SEC

" " WINDING START

N4

6

7,8

N1,N5

4

5

N3

N6

2

1

TUBE

PIN

1,2,4,5,6,11

TUBE LENGHT

12mm MIN

N2

10

11

9,10


Page 9 Form__V02

4. Electric characteristics 4.1 Inductance：

L（6---4）= 260uH±10% @ 100 KHz,1 Vrms , 25℃ L 值 CPk >=1.33 备注：CPK 值做为厂家制程能力的评估项目,不作为进料判定依据

4.2 Leakage Inductance:

Le（6---4）= 6.0μH MAX @100KHz,1 Vrms , 25℃. SEC SHORTED. 4.3 DC Bais:

L（6---4） = L(0A) x 90% MIN WK3260B @100 kHz,1Vrms, 25

4.4 DC Resistance: @ 25℃ R（6---4）= 195mΩ MAX R（1---2）= 230mΩ MAX R（11---10）= 25 mΩ MAX R（9,10---7,8）= 10mΩ MAX

4.5 Voltage Ratio

INPUT: OUTPUT: 6---4 V（1---2）= 0.1923 Vrms±10% V（11---10）= 0.1153 Vrms±10% V（9,10---7,8）= 0.1538 Vrms±10% APPLY 20 KHz , 1 Vrms, 25 BETWEEN PRIMARY WINDING ℃ （6---4）

4.6, Q Value

Q（6---4）= 100 MIN @100 KHz,1 Vrms, 25℃

4.7 HI-POT Test: P---S: AC 3750 V , 50/60 Hz , 0.5mA , 60 SEC. P---CORE: AC 500 V , 50/60 Hz , 0.5mA , 60 SEC. S---CORE: AC 3750 V , 50/60 Hz , 0.5mA , 60 SEC. NOTE: When sample test, this test must be 60 seconds.

4.8 Insulation resistance: P---S: 100MΩ MIN @DC500V P,S ---CORE: 100MΩ MIN @DC500V

4.9 Layer Short Test: Apply a voltage of 1.0KVp-p AC between the primary winding （6---4） without damage as arcing, Etc.

4.10 RH Test: R.h.90~95% ,40± 2℃, 120hrs.

P---S: AC 3750V , 50/60 Hz , 60SEC 4.11 Condition of work

(1). The part normal work be allowed ambient temperature: -25 ~ +85 .℃ ℃ (2). The part must be allowed maximum high temperature: +130 .℃ (3). The part normal work be allowed temperature rise: 40℃ (4). The part is allowed storage ambient temperature: -25 ~ +85 .℃ ℃ (5). Storage life: one year (6). The part be allowed work ambient frequency: 1 KHz ~ 300 KHz.

*送承認的樣品結構/規格/工法,與交貨到工廠的樣品結構/規格/工法須一致. (廠家要依照規格書生產製造樣品) *若使用 TAPE:*加註:規格書內,所有 2Ts, 3Ts 絕緣膠帶,是定義 -指單層膠帶繞 2Ts, 3Ts.


Page 10 Form__V02

5. Reliability : 5.1 Strength test: [Ref. GB/T 2423.29-1999]

The load of 20N (φ1.0/20N; φ0.8/15N; φ0.7, 0.6, 0.5/10N) shall be applied to the terminal and hold for 1minute. Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.2 Bending strength: [Ref. GB/T 2423.29-1999] The load of 10N (φ1.0/10N; φ0.8, 0.7, 0.6, 0.5 / 5N) shall be applied to the terminal, from the vertical direction bending 90º,back to original position, the opposite direction bending 90º, back to original position,those 4 steps is one cycle, total test 2 cycles. Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.3 Vibration: [Ref. GB/T 2423.10-2008] Amplitude:1.5mm Max,1 minute change from 10Hz-55Hz-10Hz, vibration direction: three axials X,Y,and Z, vibration time: each axial 2 hours, total of 6 hours; Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.4 High temperature resistance: [Ref. GB/T 2423.2-2008] The transformer shall be stored at 125±2℃ for 500 hours. then take out on standard atmospheric pressure for 2 hours. Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.5 Cool resistance: [Ref. GB/T 2423.1-2008] The transformer shall be stored at -25±2℃ for 500 hours. then take out on standard atmospheric pressure for 2 hours. Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.6 Damp heat: [Ref. GB/T 2423.3-2008] The transformer shall be stored at 40±2℃ and relative humidity 90%~95% for 500 hours. then take out on standard atmospheric pressure for 2 hours. Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.7 Thermal Shock: [Ref. SJ/T10004-91 & GB/T 2423.22-2002] The transformer shall be test 5 cycles,then take out on standard atmospheric pressure for 2 hours. Note: Step 1-2-3-4 is one cycle. Total: 5 cycles. Electrical, Mechanical Characteristics and insulation should not be abnormity.

5.8 Solder ability test [Ref. TPV RDS-02]

Put the terminal in fluxing for 2~3 seconds,after fluxing,component terminal shall be dipped in a melted solder bath at 235±5℃ for 2.5±0.5seconds. More than 90% of terminal electrode should be covered with solder. Note: Solder ability should meet TPV《RoHS 零件可焊性、耐焊接热试验规范》，RDS-02

5.9 Solder heat test [Ref. TPV RDS-02]

Preheat temperature：120℃ for 80 seconds,After preheat,put the component terminal dipped in a melted solder bath at 260+5/-0℃ for 10 seconds.Then inspect the sample. Electrical, Mechanical Characteristics and insulation should not be abnormity. Note: Solder heat test should meet TPV《RoHS 零件可焊性、耐焊接热试验规范》，RDS-02

STEP TEMPERATURE DURATION 1 -40±2℃ 30 minute 2 -40℃ 100℃ 2~3 minute 3 100±2℃ 30 minute 4 100℃ -40℃ 2~3 minute


Page 11 Form__V02

MADE IN CHINA

Cross Weight

New Weight

防湿

9

馱　: 福建省福清市景翔电子配件有限公司

背面

客户:

料号 :

左侧面

体积

堆层板限小心轻放向上

3

ISO 9001认证书证册号: 12-100-18264-TMS

收货单位:

地址:

通过标签

右侧面

月别标签

庨婖　　

　講

蹋?

条形码

料号:

数量:

江苏省苏州市吴中区孙武路1027-2号

数量 :

27.2 35.5

26.0

包装盒

纸箱

正面

每盒 :24PCS每箱 :9盒总数量:215PCS

6. Packing & Label (1). Quantity of the products placed in the clotty pulp:

24 PCS per Case , 9 Case per box Total quantity of one box is 215 PCS

(2). Warning: the boxes height should not be more than 8 floors. (3). Signing blue “ROHS” label under the barcode and transfort label. (4). The gross weight of one box is 11.5 kg(REF)，the net weight is 10.4 kg(REF) (5). Material of the box: 5 layer AC corrugated paper (6). Box Allowable pressure=650kgf，Impact resistance=18kgf/cm² (7). The process of packaging:


Page 12 Form__V02

7.Material List (Supplier’s BOM)

NO SUB PART TYPE UL File NO. FLAME MANUFACTURER

1 CORE

EQ33 DMR44/P41

L:33.0mm±0.5mm

W:25.0m±0.3mm

H:13.1mm±0.3mm

N/A N/A DMEGC/ACME

2 BOBBIN

PM−9820

THICKNESS 0.45mmMIN

L:40.5mm±0.3mm

W:33.0m±0.3mm

H:11.6mm±0.2mm

E41429 94V-0

/150℃

SUMITOMO BAKELITE CO

LTD

3 WIRE DD−NYU

(ANSI MW−28) E84081 130℃

PACIFIC ELECTRIC WIRE &

CABLE CO.,LTD

E213764 TŰV

B070252617001VDE

138053 4 TRIPLE WIRE TIW−M

NEMKO P01102418

130℃ COSMOLINK CO.,LTD

NO. CT 〔CT(c),

CTI GPOUP I THICKNESS 0.06mm〕

E165111

JINGJIANG YAHUA

PRESSURE SENSITIVE CO

LTD

5 TAPE NO.35660Y

〔35660Y*(%) (CTI GROUPI)

THICKNESS 0.055mm〕

E50292

130℃

SYMBIO INC

6 TUBE TEFLON TUBE

TFL E156256 200℃

GREAT HOLDING

INDUSTRIAL CO.,LTD

7 VARNISH V1380FC E75225 130℃

ELANTAS ELECTRICAL

INSULATION ELANTAS PDG

INC

8 EPOXY E−500(XX) E218090 130℃

DONGGUAN EATTO

ELECTRONIC MATERIAL CO.,

LTD

9 TIN Sn99.3Cu0.7 N/A N/A WELL FORE SPECIAL

WIRE CORPORATION

10 INK N/A N/A 多米诺标识科技有限公司

11 SOLDER (LEAD FREE SOLDER)

A02R N/A N/A 實品金屬有限公司

贵司名称限制管理物质合格保证书

敝司保证敝司（包括敝司的子公司，联营公司，以下类同）直接或通过

第 3 方单位向冠捷及其关联公司提供的制品或部品（附属物及其它随制品一

起提供的所有物品）中所包含的所有物质符合冠捷环境管理物质标准

（RDEMS-01 Ver.: A.09.0）第 4节的规定，包括以下指定的物质：

No. 物质 CAS No. 限值(ppm) 管制范围备注

20 焊锡

1 镉及其化合物 7440-43-9 50

除焊锡外的所有

均质材料，豁免项

目除外(豁免项目请参照表 Annex II)

EU: RoHS管控项目

2 铅及其化合物 7439-92-1 50

所有均质材料，豁

免项目除外(豁免项目请参照表Annex II)


ND 发光装置 ( 如CCFL, LED)，豁免项目除外 3 汞及其化合物 7439-97-6

500 其他均质材料，豁

免项目除外


不得含有金属

4 六价铬及其化合物 -- 500

除了上述项目外

的其他均质材料

(豁免项目请参照表Annex II)


5

多溴联苯(PBB)，包含十溴联苯醚(DecaBDE)的多溴二苯醚，及其氧化物 (PBDEs, PBBEs, PBBOs)

PBB: 59536-65-1 PBDE: 1163-19-5 32536-52-0 36483-60-0 32534-81-9

500

所有均质材料 EU: RoHS管控项目;含溴阻燃

剂

6 四溴二苯醚/五溴二苯醚 40088-47-9/ 32534-81-9 不得含有

黏胶, 胶水 EU: RoHS管控项目;含溴阻燃

剂

7 铍及其化合物(含氧化铍) BeO: 1304-56-9 不得有意

添加所有均质材料

8 镁及其化合物 7439-95-4 1000 所有均质材料

10 Panel中用到的玻璃

9 砷及其化合物(含五氧化二砷，三氧化二砷)

As2O5: 1303-28-2 As2O3: 1327-53-3 100

除了上述项目外


10 锑及其化合物 7440-36-0 1000 所有均质材料

11 镍及其化合物 7440-02-0 0.5 µg/cm2/周

仅限于直接与皮

肤有长期接触

(>30秒)的物品表面处理应用

12 铋及其化合物 7440-69-9 1000 所有均质材料 13 硒及其化合物 7782-49-2 1000 所有均质材料

14 二氯化钴 7646-79-9 7791-13-1 14216-74-1

不得有意

添加

用于干燥剂(硅胶等)中的湿度指示剂

15 石棉 -- 不得含有所有均质材料参照Annex I

16 臭氧层破坏物质(ODS) -- 不得含有所有均质材料参照Annex I

17 氟化温室气体 (SF6, PFCs, HFCs) -- 不得含有所有均质材料参照

Annex I 1µg/m2 涂层材料

18 全氟辛烷磺酸 (PFOA)及其酯化物(PFOS)

PFOA: 1723-23-1 1000 除了上述项目外


19 多氯化戴奥辛及呋喃 (PCDDs & PCDFs) -- 不得含有所有均质材料

20 六氯环己烷(HCH) 608-73-1 不得含有所有均质材料 21 多氯联苯(PCB) 1336-36-3 不得含有所有均质材料 22 多氯三联苯(PCT) 61788-33-8 不得含有所有均质材料 23 多氯化萘(PCN) 70776-03-3 不得含有所有均质材料

24 短链氯化石蜡（ C10-C13 SCCP）

71011-12-6 85535-84-8 85536-22-7 85681-73-8 108171-26-2

不得含有

所有均质材料

25 中链氯化石蜡 MCCP 85535-85-9 不得有意添加

所有均质材料

26 五氯苯酚(PCP)及其盐类与酯类

87-86-5 不得有意添加

所有均质材料

27 单甲基二氯二苯甲烷（Ugilec 121 或 Ugilec 21）

-- 不得含有所有均质材料

28 单甲基四氯乙烷甲烷 (Ugilec 141) 76253-60-6 不得含有所有均质材料

29 单甲基二溴二苯基甲烷（DBBT）

99688-47-8 不得含有所有均质材料

1000 所有均质材料

30 六溴环十二烷(HBCDD)及其主要光学异构物

25637-99-4 3194-55-6 134237-50-6 134237-51-7 134237-52-8

不得含有

针对中国十环认

证产品中的>25克的塑料零件

含溴阻燃

剂参照Annex I

31 四溴双酚A(TBBPA) 79-94-7 1000

除了印刷电路板、

IC封装本体、线材与连接器以外的

所有均质材料

含溴阻燃

剂

32 多溴化戴奥辛及呋喃 (PBDDs & PBDFs) -- 不得含有所有均质材料

33 特定偶氮化合物 -- 30 会与人体接触的所有均质材料

参照Annex I

34 三丁基锡（TBT）、三苯基锡（TPT）、氧化三丁锡（TBTO）

TBTO: 56-35-9 不得含有

所有均质材料

35 二丁基锡（DBT）、二辛基锡（DOT）化合物

DBTO: 818-08-6 DOTO: 870-08-6

不得含有

所有均质材料

36 壬基酚与壬基酚聚氧乙烯醚及相关物质（NP/NPEs）

-- 不得含有所有均质材料

37 烷基酚（OP） -- 不得含有所有均质材料 38 富马酸二甲酯(DMF) 624-49-7 0.1 所有均质材料

39 特定邻苯二甲酸盐 -- 1000 所有均质材料参照Annex I

39 特定邻苯二甲酸盐 -- 不得含有针对中国十环认

证产品中的>25克的塑料零件

参照Annex I

不得含有与皮肤接触30秒

以上部件

苯并 (a)芘: 20

针对中国十环认

证产品中的产品

外壳、键盘及各类

按键、鼠标外壳、

触摸板以及外接

电源线

40 多环芳香烃(PAHs) --

50 其他均质材料

参照Annex I

41 挥发性有机物(VOCs) -- 1000 黏合剂、涂料参照Annex I 42 双酚A(Bisphenol A) 80-05-7 25 塑料

43 麝香类物质(二甲苯麝香及酮麝香)

Musk xylene: 81-15-2 500

所有均质材料

44 4,4'- 二氨基二苯基甲烷（MDA）

101-77-9 1000 所有均质材料

45 2-(2'-羟基-3',5'-二叔丁基苯基)-苯并三唑

3846-71-7 不得有意添加

用于塑料中作为

紫外线防护剂、紫

外线吸收剂的用

途

46 氨基-/硝基-苯/联苯/有机物 -- 不得有意添加

所有均质材料

47 对二氨基联苯及其盐类 -- 不得含有所有均质材料

48 红磷，黄磷 7723-14-0 不得有意添加

所有均质材料

49 六氯乙烷 67-72-1 禁止非铁金属的制造与加工

50 三氯生 3380-34-5 10 所有均质材料

51 表面活性剂(DTDMAC/DODMAC/ DHTDMAC)

DTDMAC: 68783-78-8 DODMAC: 107-64-2 DHTDMAC: 61789-80-8

总和1000

清洗剂

52

磷酸三(2-氯乙基)酯(TCEP), 磷酸三(2-氯丙基)酯(TCPP)，磷酸三 (2,3- 二氯丙基 ) 酯(TDCPP)

115-96-8 13674-84-5 13674-87-8

1000 用于塑料、树脂、

纤维、布料的难燃

剂用途

53 放射性物质 -- 不得含有所有均质材料 54 高氯酸盐(Perchlorates) 7791-03-9 0.006 所有均质材料

签名(Signature):

职位 (Position):

日期 (Date):

公章 (Cachet):

Systems, Electrical Insulation - Component

Class 130 (B) insulation system, designated Viking B-2.

Class 130 (B) insulation system, designated HIS-8A.

Class 130 (B) insulation system, designated GH-130.

Class 130 (B) insulation system, designated DASH 2 B-19.

Class 130 (B) insulation system , designated CIS.04.

Class 155 (F) insulation system , designated RXT-2.

Marking: Company name or "LI TAI" and system designation.

Copyright © 2007 Underwriters Laboratories Inc.®

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright © 2007 Underwriters Laboratories Inc.®"

OBJY2.E182002Systems, Electrical Insulation - Component

Page Bottom

See General Information for Systems, Electrical Insulation - Component

LI TAI ELECTRONIC ENTERPRISE CO LTD E182002

2ND FL-2

16 JIAN BA RD

CHANG HO, TAIPEI 235 TAIWAN

Last Updated on 2006-12-14

Questions? Notice of Disclaimer Page Top

RoHS /

DIP , Wave Solder

: : 235 +5/-5 2.5 0.5 secSolderability : Test Condition : TEMP. 235 +5/-5 2.5 0.5 sec

: 90%90% coverage,

[ RoHS ]Please see attachment for details

: : 260 –0/+2 10 0.5 sec [ ]Resistance to Soldering Heat: Test Condition : TEMP. 260 –0/+2 10 0.5 sec (Terminal)

:


SMD , Solder Reflow

: : 235 +5/-5 2.5 0.5 sec Solderability : Test Condition : TEMP. 235 +5/–5 2.5 0.5 sec

: 90% 90% coverage,


: : 260 + 5 10 –0.5/+0.5 secResistance to Soldering Heat: Test Condition : TEMP. 260 –0/+5 10–0.5/+0.5 sec (Terminal)

:


RoHS RoHS

RoHS

___________________ Supplier Name

_______________________ Signature

_________________________ Company Seal

Plastics - Component

QMFZ2.E41429Plastics - Component

Additional information regarding this certification can be found in UL's iQ Family of Databases (www.ul.com/iq).

NEW -- for additional information concerning the individual material, click on the material designation.

Page Bottom

See General Information for Plastics - Component

SUMITOMO BAKELITE CO LTD E41429

5-8 HIGASHI-SHINAGAWA 2-CHOME

SHINAGAWA-KU

TOKYO, 140-0002 JAPAN

H D

Min. H H R T I V 4 C

Thk Flame W A Elec Mech T 9 T

Material Dsg Color mm Class I I Imp Str R 5 I

Acrylonitrile Butadiene Styrene (ABS), modified, "PERMAFLOW", furnished as pellets.

U-101 ALL 1.5 V-1 3 0 60 60 60 2

3.0 V-0 1 0 60 60 60

Acrylonitrile Butadiene Styrene (ABS), "Sumikon", furnished as pellets.

FM-CS200 BK 1.5 HB - - 60 60 60

FM-CS20A BK 0.96 HB - - 60 60 60

-3.0 - - - - - -

FM-MS100XX NC 1.0-3.0 HB - - 60 60 60

Alkyd Molding Compound "Polyester" (AMC), "SUMIKON", furnished as granular, pellets.

TM-4101 ALL 0.86 HB 3 1 105 130 130 0

3.0 HB 0 1 105 130 130

TM-4120 ALL 0.75 V-0 - - 105 130 130 0 4 0

1.1 V-0 0 1 105 130 130

BK, BN 0.75 V-0 - - 105 130 130

3.0 V-0 0 0 105 130 130

TM-4125 BK 0.75 V-0 1 0 105 130 130 0 4 0

1.5 V-0 1 0 105 130 130

3.0 V-0 0 0 105 130 130

Alkyd Molding Compound "Polyester" (AMC), "Sumikon", furnished as pellets, granular material.

TM-4190 ALL 1.5 V-0 1 0 105 130 130 0

2.1 V-0 1 0 105 130 130

3.0 V-0 0 0 130 130 130

TM-4195 BK, BN 1.5 V-0 1 0 105 130 130 4 0

3.0 V-0 0 2 150 150 150

PM-950 BK 0.48 V-0 - - 150 150 150

PM-9501 BK 1.5 V-0 - - 150 150 150 3

3.0 V-0 - - 150 150 150

PM-950J BK 0.48 V-0 - - 150 150 150

PM-9600 BK 3.0 V-0 - - 150 150 150

PM-9620 BK 1.0 V-0 - - 150 150 150

PM-9630 BK 0.16 V-0 4 0 150 150 150 0 4 3

0.32 V-0 3 0 150 150 150

0.51 V-0 0 0 150 150 150

3.0 V-0 0 1 150 150 150

PM-9650 BK 0.81 V-1 - - 150 150 150

1.5 V-0 - - 150 150 150

PM-9660 NC, BN, BK 0.46 V-0 - - 150 150 150

0.75 V-0 - - 150 150 150

PM-9690 BK 0.75 V-1 - - 150 150 150

1.5 V-1 - - 150 150 150

3.0 V-0 - - 150 150 150

PM-9720 BK, BN 0.28 V-0 - - 150 150 150 0 5 3

0.75 V-0 2 3 150 150 150

1.5 V-0 0 0 150 150 150

3.5 V-0 0 2 150 150 150

PM-9750 BK 0.30 V-0 - - 150 150 150 0 4 3

BK, BN 0.43 V-0 2 3 150 150 150

1.5 V-0 0 3 150 150 150

3.0 V-0 0 3 150 150 150

PM-9800 BK 0.81 HB - - 150 150 150

PM-9820 BK 0.16 V-0 - - 150 150 150 0 5 3

0.51 V-0 3 1 150 150 150

BN 0.18 V-0 - - 150 150 150

0.70 V-0 1 2 150 150 150

1.5 V-0 0 2 150 150 150

3.0 V-0 0 2 150 150 150

PM-9830 BK 0.69 V-0 0 0 150 150 150 0 4 3

3.0 V-0 0 0 150 150 150

PM-9850 BK 0.29 V-0 - - 150 150 150

PM-9870 BK 0.61 V-0 - - 150 150 150

Phenolic (PF), "SUMIKON".

PM-6432M BK 3.0 V-0 - - 150 150 150

RX-8652S BK 1.5 V-0 - - 150 150 150

TEST REPORT FOR FLAME CLASS 94V-0./

BALL PRESSURE TEST FOR BOBBIN

****BOBBIN 94V-0

BOBBIN: .MANUFACTURER:CHANG CHUN PLASTICS CO., LTD

.MANUFACTURER PART NO:PM-9820

BOBBIN:PM-9820

TEST

SAMPLE

SAMPLE1 10S 0S 0S OK





*** 10S

*** BALL PRESSURE TEST FOR BOBBIN:

1. OPERATING AMBIENT TEMPERATURE 125 ,1hr.

2. AFTER TEST PET ITEM 1,THEN MEASURED THE DIMETER OF HOLE ABOUT 0.5mm

3. THE TEST CAN MEET IEC 950 ALL REQUIRENENT.

REMARK: ***BOBBIN***

1. MAKER: SUMITOMO BAKELITE CO.,LTD2. MATERIAL: PHENOLI C

3. P/N: PM-9820,94V -0

4. UL FILE NO: E41429

Insulating Tape - Component

Polyethylene-Terephthalate film insulating tape with acrylic adhesive, Cat. No. 35660*@, rated 130° C.

Polyethylene-Terephthalate film insulating tape with acrylic adhesive, Cat. Nos. 35660*@, rated 130° C; Cat. No. 35660Y*(%), rated 130 C.

Flame retardant double sided acrylic tape, Cat. No. DS31+.

Aramid "Nomex" paper insulating tape, Cat. No. NM130* rated 155 C .

Aramid "Nomex" paper insulating tape, Cat. No. NM13K*, rated 155 C.

Woven glass cloth backing with silicone adhesive, Cat. Nos. GL06* and GL08*, rated 200 C.

Woven glass cloth insulating tape with acrylic adhesive, Cat. No. GL15 rated 155 C.

Woven glass cloth insulating tape with rubber adhesive, Cat. No. GL27 rated 130 C.

Polyethylene-Terephalate film insulating tape with acrylic adhesive, Cat. No. MY130# rated 130 C.

Polyethylene-Terephalate film insulating tape with acrylic adhesive, Cat. No. MY9XHF(e)(f), rated 130 C, where X represents tape color: 0 = red, 1 = yellow, 2 = blue, 3 = green, B = black, W = white.

Polyimide film insulating tape with silicone base adhesive, Cat. No. KA180* rated 200 C.

Woven acetate cloth insulating tape with rubber base adhesive, Cat. No. ACO* rated 130 C.

Polyethylene-Terephthalate film insulating tape with acrylic adhesive, Cat. No. 35661$ rated 130 C.

Polyethylene-Terephthalate film insulating tape with rubber based adhesive, Cat. No. MYOY(&), rated 130C.

Polyimide film insulating tape with acrylic adhesive, Cat. No. KA170*, rated 200 C.

Polyethylene-Terephthalate film insulating tape with acrylic adhesive, Cat. No. 35660W*c, rated 130 C.

Polyimide film insulating tape with silicone base adhesive, Cat. No. KA180L* , rated 200 C.

Polyimide film insulating tape with silicone base adhesive, Cat. No. KA180H*, rated 200 C.

Polyimide film insulating tape with silicone base adhesive, Cat. No. KA180HA*, rated 200 C.

Polyimide film insulating tape with silicone base adhesive, Cat. Nos. KA180K* and KA180E*, rated 200 C.

Polyimide film insulating tape with silicone base adhesive, Cat. No. KA200*, rated 200 C.

Woven fiberglass coated with PTFE insulating tape with silicone base adhesive, Cat. No. TF05*, rated 180 C.

Polyethylene-Terephthalate film insulating tape with acrylic adhesive, Cat. No. MY9XAF*(g), where X represents tape color: 0 = red, 1 = yellow, 2 = blue, 3 = green, B = black, W = white,Y = light yellow, C = Clear, rated 130°C.

Polyethylene-Terephthalate film with non-woven PET fiber reinforcement insulating tape with acrylic adhesive, Cat. Nos. 35661-3(h) and 35661-2(h) rated 130 C.

+ - Subjected to flame retardant test only. Shall be marked "Flame Retardant" only.

* - Complies with flame retardant requirements when so marked.

OANZ2.E50292 Insulating Tape - Component

Page Bottom

See General Information for Insulating Tape - Component

SYMBIO INC E50292

12 XING HUA RD

TAOYUAN, 330 TAIWAN

1 2OANZ2.E50292 - Insulating Tape - Component

2011/3/28http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name...

@ - "Film side CTI Performance Level Category PLC=3, Voltage 225 or less, per UL 746A/ASTM D3638", and/or "Film side CTI225 per IEC112, Third Edition (1979) ", and/or "Adhesive side CTI Performance Level Category PLC=2, Voltage 250 or less, per UL 746A/ASTM D3638", and/or "Adhesive side CTI 250 per IEC112, Third Edition (1979) " or equivalent.

# - "Film side CTI Performance Level Category PLC = 3 Voltage 200 or less per UL 746A/ASTM D3638", or equivalent.

$ - "Film/adhesive side CTI Performance Level Category PLC=0, Voltage 600 or greater, per UL 746A/ASTM D 3638" and/or "Film/adhesive side CTI 600 per IEC112, Third Edition (1979)" or equivalent.

(&) - "CTI Performance Level Category film side PLC=O, Voltage 600 or greater, per UL 746A/ASTM D3638" and/or "Film Side CTI 600 - 0.19mm per IEC112, Third Edition (1979)" or equivalent.

(c) - "Adhesive side CTI Performance Level Category PLC=0, Voltage 600 or greater, per UL 746A/ASTM D 3638", and/or "Adhesive side CTI 600 per IEC112, Third Edition (1979)", and/or "Film side CTI Performance Level Category PLC=1, Voltage 420 or less, per UL 746A/ASTM D 3638", and/or "Film side CTI 420(380) per IEC112, Third Edition (1979)" or equivalent.

(d) - "Adhesive side CTI Performance Level Category PLC=0, Voltage 600 or greater, per UL 746A/ASTM D 3638", and/or "Adhesive side CTI 575-0.20 per IEC 60112, Fourth Edition (2003)", and/or "Film side CTI Performance Level Category PLC=0, Voltage 600 or greater, per UL 746A/ASTM D 3638", and/or "Film side CTI 575-0.43 per IEC 60112, Fourth Edition (2003), or equivalent.".

(e) - Tape Cat. No. MY9BHF in black color only complies with flame retardant requirements when so marked.

(f) - "Film side CTI Performance Level Category PLC=2, Voltage 281, per UL 746A/ASTM D3638", and/or "Adhesive side CTI Performance Level Category PLC=2, Voltage 385, per UL 746A/ASTM D3638", or equivalent.

(g) - "Film side CTI Performance Level Category PLC = 3, Voltage 228, per UL 746A/ASTM D3638", and/or "Adhesive side CTI Performance Level Category PLC = 2, Voltage 302, per UL 746A/ASTM D3638", or equivalent.

(h) - "Film/adhesive side CTI Performance Level Category PLC=0, Voltage 600 or greater, per UL 746A/ASTM D 3638" or equivalent.

(%) Adhesive side CTI Performance Level Category PLC=0, Voltage 600 or greater, per UL 746A/ASTM D 3638 or "Adhesive side CTI 575-0.20 per IEC60112, 4th Edition (2003)" or "Film side CTI Performance Level Category PLC=0,Voltage 600 or greater, per UL 746A/ASTM D 3638" or "Film side CTI 575-0.43 per IEC60112, 4th Edition (2003)"or equivalent.

Marking: Company name or file number "E50292", catalog designation and "Flame Retardant" if authorized, printed on carton, wrapper and/or core.

Copyright ?2011 Underwriters Laboratories Inc.®

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufacturedunder UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." mustappear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright © 2011 Underwriters Laboratories Inc.®"


Questions? Print this page Notice of Disclaimer Page Top

2 2OANZ2.E50292 - Insulating Tape - Component


Administrator線段

Administrator線段

Insulating Tape - Component

Copper foil tape, Cat. No. CP-3002*.

Nonwoven cloth/polyethylene terepthalate film tape, Cat. No. WF with suffixes, rated 130 C* (c) (h).

Polimide film tape, Cat. No. PF with suffixes, rated 180 C* (d) (g).

Polyethylene terephthalate film tape, Cat. No. CT with suffixes, yellow color, rated 130 C*(c) (e) (g).

Polyethylene terephthalate film tape, Cat. No. CT with suffixes, all colors except yellow, rated 130 C(b)(f) (g).

Polyethylene terephthalate film tape, Cat. No. PZ with additional suffixes, rated 130 C*(b).

*Complies with flame retardant requirements when so marked.

(b)Comparative Tracking Index (CTI) performance indicates material Group IIIa, PLC=2, CTI equal to or greater than 250 but less than 400 v.

(c)Comparative Tracking Index (CTI) performance indicates material Group I, PLC=0, CTI equal to or greater than 600 v.

(d)Comparative Tracking Index (CTI) performance indicates material Group IIIb, PLC=4, CTI equal to or greater than 100 v but less than 175v.

(e) - Yellow color only

(f) - All colors except yellow

(g) - The CTI test was conducted per IEC 112, 3rd Edition 1979 and the assigned level is based on the testing of both film and adhesive sides.

(h) - The CTI test was conducted per IEC 60112, 4th Edition 2003 and the assigned level is based on the testing of both film and adhesive sides.

Marking: Company name or "E165111" and catalog designation printed on the carton, wrapper or core.

Copyright © 2008 Underwriters Laboratories Inc.®


OANZ2.E165111Insulating Tape - Component

Page Bottom

See General Information for Insulating Tape - Component

JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO LTD E165111

SOUTHWEST AROUND RD

JINGJIANG, JIANGSU 214500 CHINA


Questions? Notice of Disclaimer Page Top

YAHUA FLAME-RETARDANT POLYESTER ADHESIVE TAPE

NO. CT Tape1. Feature

1) Excellent electric insulating properties2) Flame-retardant, UL-listed under the subject 510 FR. 3) Heat resistant, UL-listed under the subject 510 at 130 (Class B).4) Specifications about an environment related substances

--- None use of prohibited substances, all products accord with RoHS, SS-00259 and Customers' requests.

2. ConstructionSketch Map of CT Tape’s Structure 1mil & 2mil

3. General Properties

Testing Item UnitCT Standard values

1mil(25#) 2mil(50#) *Adhesion to steel N/10mm 3.8 3.8

*Peeling strength N/M 300 or more 300 or more

*Heat resistance ---- Good Good

*Tensile strength N/10mm 44 88

*Elongation % 80 80

*Solvent resistance ---- Excellent Excellent

Insulating Resistance >1 106 >1 106

*Dielectric breakdown KV 5.0 6.5

*Electrolytic corrosion coefficient ---- 0.98 0.98

*Heat resistance temperature ---- UL temperature rating

130

UL temperature rating

130

CTI grade ---- I IValues listed above are typical and should not be used for any specification purposes.

Note:1) Test Method: ASTM-D1000 2) Colour: Light Yellow3) UL Recognized File No.: E165111 4) Shelf Life: 12 months when storage in original carton at 23 and 65% relative humidity.

(Backing Material):Pet Film

Adhesive

Acrylic Adhesive

0.025 0.003(0.050 0.005 )

Thickness:0.035 0.005

Thickness

Single- and Multi-layer Insulated Winding Wire - Component

Cat. No. TIW-M, reinforced insulation rated 130°C (Class B), 1.41 kV peak for Information Technology Equipment, 18 - 32 AWG (1.00 - 0.20 mm).

Cat. No. TIW-M (F) reinforced insulation rated 155°C (Class F), 1.41 kV peak for Information Technology Equipment, 18 - 32 AWG.

Cat. No. TIW-M (B) reinforced insulation rated 130°C (Class B), 1.41 kV peak for Information Technology Equipment, 18 - 32 AWG.

Cat. No. TIW-M (A) reinforced insulation rated 105°C (Class A), 1.41 kV peak for Information Technology Equipment, 18 - 32 AWG.

Marking: Company name and material designation on smallest unit container, spool or on a tag attached to the end of the wire, and the

Recognized Component Mark .

2013 UL LLC

When the UL Leaf Mark is on the product, or when the word "Environment" is included in the UL Mark, please search the UL Environment databasefor additional information regarding this product's certification.

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufacturedunder UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "© 2013 UL LLC".

OBJT2.E213764 Single- and Multi-layer Insulated Winding Wire - Component

Page Bottom

See General Information for Single- and Multi-layer Insulated Winding Wire - Component

COSMOLINK CO LTD E213764

449 GUN GIN-LEE

IWON-MYUN

OKCHUN-GUN, CHUNG CHONG BUK-DO 373-860 REPUBLIC OF KOREA


Questions? Print this page Terms of Use Page Top

1 1OBJT2.E213764 - Single- and Multi-layer Insulated Winding Wire - Component


Tubing, Extruded Insulating - Component

#- Tubing is considered to comply with the optional VW-1 flammability requirements only if so marked.

Marking: Company name or "E156256" or trademark , catalog number, voltage rating, temperature rating in degrees C and inside diameter, shall be marked on tags attached to both ends of the tubing on the shipping spool label or on the smallest unit container.



UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright © 2010 Underwriters Laboratories Inc.®"

YDPU2.E156256 Tubing, Extruded Insulating - Component

Page Bottom

See General Information for Tubing, Extruded Insulating - Component

GREAT HOLDING INDUSTRIAL CO LTD E156256

10TH FL

649-3 CHUNG CHENG RD

HSIN CHUNG

TAIPEI HSIEN, 242 TAIWAN

Cat. No.Max

VMax

Temp CCol

Recognized

Max Temp

Rated Oil Resistance, C

VW-1Rated #

Not heat-shrinkable polytetrafluoroethylene (PTFE) tubing.

TFL 150 200 BL,NAT Yes

TFT 300 200 BL,NAT Yes

TFS 600 200 BL,NAT Yes

TFL-201 150 200 NAT Yes

TFT-201 300 200 NAT Yes

TFS-201 600 200 NAT Yes



Varnishes - Component

OBOR2.E75225Varnishes - Component

Page Bottom

See General Information for Varnishes - Component

ELANTAS ELECTRICAL INSULATION ELANTAS PDG INC E75225

5200 N 2ND ST

ST LOUIS, MO 63147 USA

Varnish Dsg

ANSI Magnet

Wire Type

Varnish Thermal Class C

TP HC CE

700, 12-0-12-C-66 MW28 130 130

MW76 155 180

MW35 180 200

MW16 220 180

961, 961-40 MW28 130 130

MW76 155 180

MW35 180 200

MW26 155 180

MW16 220 155

91 Hi Bond MW28 130 130

MW76 155 180

MW35 180 200

MW16 220 180

711-F-2106 MW28 130 130

MW76 155 200

MW35 180 200

MW26 180 180

MW16 240 180

MW35A 200

740-2103 MW28 130 130

MW76 155 180

MW35 155 200

MW16 220 180

777, 2000 MW28 130 130

* - With or without suffix -66.

** - Not a commercially available varnish. Data provided for reference purposes only.

@ - May be followed by "XX solids, YY version", where XX represents the percentage of nonvolatile and YY represents the type of co-solvent. All of which relates to viscosity. May be followed by a one or two digit alphanumeric suffix, possibly followed by -

MW35 180

577 MW35 200 155

GRC20, -20 Rev 3, -27, -81 (xx) MW76 180 180

MW35 200 200

MW28 130

GRC51, -57, -59(+++) MW28 130

MW35 180 180

GRC20/4(x), -20/4B(x), -20/4C(x) MW28 130

MW35 180

GRC20/8 MW28 130 155

MW35 200 200

MW16 220 180

8181-01 MW35 180

Esterlite 805 MW28 130

MW76 155

MW35 180

9183 MW35 180 200

V1630FS, V1630, V1630FS50, V1630FS Black, 80361, 80361FS MW28 130 155

MW35 180 180

MW76 155

MW80 155

C1525A, C1525F35, C1525G45 MW16 240

MW28 130

MW35 180 180

MW76 180

MW80 130

V1380, V1380FC, V1380FC Black, 80381FC MW16 240

MW28 130

MW35 180 180

MW76 180

MW80 130

V1305A MW35 155

66, possibly followed by -B, -R, -S or -T, all indicating the types and amounts of solvents, fillers and/or colors. Isolite varnishdesignations may be followed by the letters A, B, C, F, H, LV, M, PC T or a color.

@@ - May be followed by suffixes XXYYY in which XX represent the solid content and three letters replace YYY indicating the color.

% - Isolite varnish designations may be followed by the letters A, B, C, F, H, LV, M, PC, T or a color.

%% - RSTAI bondable wire.

# - MW24 construction with 180 C temperature class rating.

(##) - May be 0-70 percent silica filled.

$ - Polyborndex G Bond M Bondable wire.

$$ - Magnebond CAB-180 by Nexans.

(++) - Varnish 7183 may be supplied in 2 parts the individual parts are designated "70V+ promoted Part A" and "70VT inhiited Part 3".

(+3) - May be followed by XXF. Where XX designates level of inorganic filler and letter F or filler.

(x) - May be preceeded by prefix "E" and may be followed by a one to five alphanumeric suffix indicating percent of inert fillerand/or color.

(+)-Designation may optionally include two digit suffix indicating percent inorganic filler.

(+++)-Replaced by number denoting solids content (%).

Grade designations may have -66 suffix.

Marking: Company name or trademarks , "THERMELEC", "ISONEL®", "AQUANEL®", "ISOLITE®" or "ISOPOXY®" and varnish designation, which may be preceded by "PED" or "Pedigree" on shipping container.



UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1.The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright © 2010 Underwriters Laboratories Inc.®"



Plastics - Component

(XX) - Denotes two letters, AA - ZZ, representing a customer code of Dongguan Eatto.

Marking: Company name and material designation on container, wrapper or finished part.



UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide

QMFZ2.E218090Plastics - Component

Additional information regarding this certification can be found in UL's iQ Family of Databases (iq.ul.com).

NEW -- for additional information concerning the individual material, click on the material designation.

Page Bottom

See General Information for Plastics - Component

DONGGUAN EATTO ELECTRONIC MATERIAL CO LTD E218090

GUANWAN INDUSTRIAL

XINWAN

HUMEN TOWN

DONGGUAN, GUANGDONG 523938 CHINA

H D

Min. H H R T I V 4 C

Thk Flame W A Elec Mech T 9 T

Material Dsg Color mm Class I I Imp Str R 5 I

Epoxy Molding Compound (EP - Molding), furnished as paste.

E-500 (XX) ALL 3.0 V-0 - - 130 130 130

Epoxy Potting Compound (EP - Potting), furnished as single-part paste.

3300 WT, BK 3.0 V-0, 5VA - - 90 90 90

10.0 V-0, 5VA - - 90 90 90

Epoxy Potting Compound (EP - Potting), furnished as two liquid components.

3300A-1/3300B-1 BK, YL 1.0 V-0 3 0 130 130 130 0

3.0 V-0 1 0 130 130 130

3300A-2/3300B-2 NC, WT, RD 1.0 V-0 - - 130 130 130

3.0 V-0 - - 130 130 130

3300A/B BK 1.0-1.1 V-0 - - 90 90 90

2.6-2.86 V-1 - - 90 90 90

WT, RD 1.0 V-0 - - 90 90 90

2.6-2.86 V-0 - - 90 90 90

3300AB(1) ALL 3.0-3.3 V-0, 5VA 0 0 90 90 90 4



Administrator線段

Core Vendor /Type DMEGC/E

Core Loss

g/cm2 E M

Pcv (Kw/M3)@ 80 Pcv (Kw/M3)@ 100

DMR44( PC44) 4.8 50N

MIN

50N

MIN

320 (Kw/M3) MAX 300(Kw/M3) MAX

Initial Permeability curve V.S. Temperature Power loss curve (Pcv max) V.S. Temperature

Core Vendor /Type ACME/ EQ33

Core Loss

g/cm2 E M

Pcv (Kw/M3)@ 80 Pcv (Kw/M3)@ 100

P41(

PC44)

4.85 50N

MIN

50N

MIN

420(Kw/M3) MAX 400(Kw/M3) MAX

Initial Permeability curve V.S. Temperature Power loss curve (Pcv max) V.S. Temperature

Administrator文字方塊

Administrator文字方塊PT-019875

Administrator文字方塊PT-019875

Administrator矩形

TPV : : : :

PREPARED BY: CHECKED BY: APPROVED BY:

PT-019875

LI TAI ELECTRONIC ENTERPRISE CO., LTD. CERTIFICATE OF COMPLANCE

CUSTOMER PART NUMBER:

LI TAI PART NUMBER: PT-019875

PURCHASE ORDER NUMBER:

LI TAI LOT NUMBER:

SHIPPING DATE:

QUANTITY IN LOT:

THIS IS TO CERTIFY THAT THE ENCLOSED UNITS ARE IN STRICT COMPLIANCE

WITH THE APPROVED SAMPLE AND/CURRENT LI TAI ADVERTISED SPECIFICATIONS

THIS PART HAS BEEN DESIGNED TO COMPLY WITH THE CREEPAGE AND CLEARANCE

DISTANCES REQUIRED PER IEC60950 / IEC 60065 AND 100% HI-POT TEST.

PRODUCTION TEST CONDITION:

PRIMARY TO SECONDARY: 4500 VAC 0.5 mA 1 SEC.

PRIMARY TO CORE: 2250 VAC 0.5 mA 1 SEC.

SECONDARY TO CORE: 4500 VAC 0.5 mA 1 SEC.

* PS : Production Line - Hi-pot 100% Test Time 1 Second ( It doesn’t include the Ramp up time of the Equipment ).

生产线打 HI-POT 100% Test Time 1 Second（不包括仪器爬升到设定电压的时间）

LI TAI PLANT: 福清 MANAGER OF Q.C: IN SP ECTED BY:

版本:A 表单编号:10RQ10

Documents

TPV Component Specificationows2.tpv-tech.com/e_mp/uploadfile/specification/201505/T...TPV Component Specification Page 3 Form__V02 1. Transformer Incoming Inspection Key Items No