Upload
muhammad-aqeel
View
386
Download
44
Embed Size (px)
Citation preview
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
1/12
Power Training for D.G. delay sta
Applied to ZXDU68 W301/T601 Ver. 5
Prepared B
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
2/12
Content
ATS relay control Generator Start
Serial Connect Rectifier D.G. control relay
How to find 2relay port?
Function verify at site with Manual Mode
D.G. Auto start & stop testing @Auto Mod
GEM active alarms o/p from SIU
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
3/12
ATS relay control Generator Start Princip
There is ATS rel
status is OPEN.
When CP OFF, t
relay is change t
Then AMF remo
Generator.
When CP is ON,
active, and relay
Then AMF remo
Generator.
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
4/12
Serial Connect Rectifier D.G. control relaAfter W301 D.G. cont
Open) serial connect w
D.G. start was controll
When CP OFF, ATS se
battery discharge, whe
start voltageDC Low
Low), then CSU relay
changed to CLOSE .
Then AMF remote star
When CP is ON, the se
circuit is OPEN, then A
the Generator.
When Generator charg
Capacity 100% achiev
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
5/12
How to find 2relay port?----CSU Relay Rectifier Relay from SIB board X17 PIN1&2
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
6/12
How to find 2relay port?----ATS RelayIf you dont know ATS control, D.G. maintenance guy can find it easy
You can find the relay at AMF side or ATS box side.
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
7/12
Function verify at site with Manual Mode1st change the Generator Mode to Manual in CSU Batt Para(password:0063)
2nd Switch OFF CP(@MCCB) before ATS, make sure ATS relay is act.
3rd find GEN Ctrl in CSU Ctrl menu, Turn On/Off GEN to verify the function of C
After Manual M
change back Ge
Auto, and test w
0063
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
8/12
D.G. Auto start&stop testing @Auto Mode
2nd change the DC Low Vol. & Batt. Low Volt as 53.0V in CSU Batt Para(password:0063)
1st MCCB switch OFF, ATS relay act.
3rd When DC voltage & Batt Volt
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
9/12
GEM active Alarm
GEM Active alarm:
Its port is SIU Output port 1(Comm1 and NO1), also need to configure BDischarge output relay as A1.
Below are the steps in Para Settings
Para Set > (Password0063)> Alarm Attri. > Batt Discharge > Relay > A1
(> Means Enter)
Take it from b/m slide port and patch it at DDF port 5(White/Grey). For t
power Off AC breaker and Site on batteries then GEM active alarm app
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
10/12
GEM active alarms o/p port in SIU.
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
11/12
Site on-line support:
First call: Abid Khan, 03134774307 TP Ran Power MangeNajeeb, 03458541071 TP Ran Power Manger @C1
Mansoor Malik, 03456190036 TP Ran Power Mang
Anjum Sohail, 03453198563 TP Ran Power Manag
Second Call: JunSan, 03145101341 Power proManager@PK
7/29/2019 TP Project Power Train--ZXDU68 W301 DG Delay1
12/12