Upload
avice-atkins
View
212
Download
0
Embed Size (px)
Citation preview
P R O D U C T I N F O R M AT I O N S H E E T
Safety rating of this project is Grade 2, and
the reasonable life span of this project is 25
years
S T E E L WA R E H O U S E
The basics of a separate
design:
Roof dead load:
0.20KN/m2
Roof Live load: 0.30
KN/M2
Wind Load: 0.40 KN/m2
Snow Load: 0.00 KN/m2 HSE-PIS-Warehouse
Page 1 of 10
E N T E R P R I S E S I N C
Highseas
W A R E H O U S E O F 4 6 5 m 2 :
Size: 30.5m x 15.25m
Height: 7m
Walls made of 0.5mm colour steel
corrugated sheets
Roof made of 0.5mm colour steel
corrugated sheets and 50mm glass
insulation wool
9 Aluminum single glass sliding windows –
48” x 48”
2 Small steel security doors – 36” x 82”
1 Large steel electric shutter door – 160”
x 160”
A warehouse of this size will fit in 1 x 40ft
container
W A R E H O U S E O F 7 . 3 0 0 m 2 :
Size: 120m X 60m
Height: 20m
Walls made of 0.5mm colour steel
corrugated sheets
Roof made of 0.5mm colour steel
corrugated sheets and 50mm glass
insulation wool and stainless steel net
2 electric rolling steel security doors – 5m
x 5m
4 larger electric rolling steel security doors
– 8m x 7m
A warehouse of this size will fill 17 x 40ft
containers
C I F P R I C E : U S $
7 9 , 5 1 5 . 0 0
C I F P R I C E : U S $
1 , 3 3 5 , 9 0 0 . 0 0
S P E C I F I C A T I O N S A N D S T E E L S T R U C T U R E
M A T E R I A L Main components material of Steel frame beam, pillar is Q235, Its material chemical composition and mechanical properties should be in line with national standards – carbon construction steel-(GB/T700-88).Purlin use cold-formed steel, with quality standard – General Cold forming sectional steel- (GB6723-86).
W E L D I N G R O D Q235B steel weld by hand, adapt E43XX style welding rod, the function –carbon steel covered electrode- (GB/T5117-95). Adapt automatic or semi-automatic, use –Welded wires-(GB1300-77) with H08 or H08A wire with the manganese – based or high manganese based flux. Q235B steel weld by hand, adapt E05XX style welding rod, Adapt automatic or semi-automatic, use –welded wires- (GB1300-77) with H08MnA wire with the manganese-based or high-manganese –based flux. Black rough bolt, nuts and washers adapt a (GB700-88)with Q235 steel, the heat treatment, productive and technical requirements will be to in line with (GB5780-86),(GB41-86),(GB95-85).The 10.9 grade high-strength bolt adopt he big orthohexagonal bolt, its function will consistent with national standard –high-strength steel with large hexagon head bolts, large hexagon head nuts, washers and technological conditions (GB1231-91) with 35VB steel, the pre-pull of high-strength bolt is: M16:P=100KN M20:P=155KN.
I N S TA L L A T I O N O F S T R U C T U R E : Before with pre-installation component to conduct a comprehensive inspection, such as the quantities of components, length, perpendicularity , joints installed between the bolt hole size with the design requirementsWhen lifting, should take appropriate measures to prevent excessive bending deformations. After lifting the structure in place, should be fastened/timely support and other components connected to guarantee the stability of componentsAll of the structure lifting, must be in the lower part of the structure in place, correction and fastened support component, then would be requiredConstruction requirements of High-strength bolt:1. High-strength bolt hole should be adapted drilled hole.2. Before installation, match with the bolts and nuts, and nut with a small amount of
mineral oil. 3. In the high-strength bolts connecting the framework of the contact elements to deal
with the use of sandblasting, anti-slip coefficient u, may not paint or defaced.
D E S C A L I N G A N D PA I N T O F S T E E L S T R U C T U R E : Before coating of the components, must deal with surface shot blasting and derusting, the derusting grade is Sa2.5.The first painting with red lead paint, surface is alkyd ready mixed paint. Steel structure in the use of process, should be conducted every three years paint maintenance, of local paint. This note as a general steel plant, if the production of corrosive gases or high temperature and humidity should be dealt with separately.
HSE-PIS-WarehousePage 2 of 10